Hybrid /spl Sigma//spl Delta/ modulators with adaptive calibration

This paper describes an architecture for stable high-order /spl Sigma//spl Delta/ modulation. The architecture is based on a hybrid /spl Sigma//spl Delta/ modulator, wherein hybrid integrators replace conventional analog integrators. The hybrid integrator, which is a combination of an analog integrator and a digital integrator, offers an increased dynamic range and helps make the resulting high-order /spl Sigma//spl Delta/ modulator stable. However, the hybrid /spl Sigma//spl Delta/ modulator relies on precise matching of analog and digital paths. In this paper, a calibration technique to alleviate possible mismatch between analog and digital paths is proposed. The calibration adaptively adjusts the digital integrators so that their transfer functions match the transfer functions of corresponding analog integrators. Through behavioral-level simulations of fourth-order /spl Sigma//spl Delta/ modulators, the calibration technique is verified.     

A direct digital frequency synthesizer with fourth-order phase domain /spl Delta//spl Sigma/ noise shaper and 12-bit current-steering DAC

This paper presents a direct digital frequency synthesizer (DDFS) with a 16-bit accumulator, a fourth-order phase domain single-stage /spl Delta//spl Sigma/ interpolator, and a 300-MS/s 12-bit current-steering DAC based on the Q/sup 2/ Random Walk switching scheme. The /spl Delta//spl Sigma/ interpolator is used to reduce the phase truncation error and the ROM size. The implemented fourth-order single-stage /spl Delta//spl Sigma/ noise shaper reduces the effective phase bits by four and reduces the ROM size by 16 times. The DDFS prototype is fabricated in a 0.35-/spl mu/m CMOS technology with active area of 1.11mm/sup 2/ including a 12-bit DAC. The measured DDFS spurious-free dynamic range (SFDR) is greater than 78 dB using a reduced ROM with 8-bit phase, 12-bit amplitude resolution and a size of 0.09 mm/sup 2/. The total power consumption of the DDFS is 200mW with a 3.3-V power supply.     

IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator for digital receiver applications

Bandpass modulators sampling at high IFs (/spl sim/200 MHz) allow direct sampling of an IF signal, reducing analog hardware, and make it easier to realize completely software-programmable receivers. This paper presents the circuit design of and test results from a continuous-time tunable IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator implemented in InP HBT IC technology for use in a multimode digital receiver application. The bandpass /spl Delta//spl Sigma/ modulator is fabricated in AlInAs-GaInAs heterojunction bipolar technology with a peak unity current gain cutoff frequency (f/sub T/) of 130 GHz and a maximum frequency of oscillation (f/sub MAX/) of 130 GHz. The fourth-order bandpass /spl Delta//spl Sigma/ modulator consists of two bandpass resonators that can be tuned to optimize both wide-band and narrow-band operation. The IF is tunable from 140 to 210 MHz in this /spl Delta//spl Sigma/ modulator for use in multiple platform applications. Operating from /spl plusmn/5-V power supplies, the fabricated fourth-order /spl Delta//spl Sigma/ modulator sampling at 4 GSPS demonstrates stable behavior and achieves a signal-to-(noise + distortion) ratio (SNDR) of 78 dB at 1 MHz BW and 50 dB at 60 MHz BW. The average SNDR performance measured on over 250 parts is 72.5 dB at 1 MHz BW and 47.7 dB at 60 MHz BW.     

A time-delay jitter-insensitive continuous-time bandpass /spl Delta//spl Sigma/ modulator architecture

In this paper, we present a new continuous-time bandpass delta-sigma (/spl Delta//spl Sigma/) modulator architecture with mixer inside the feedback loop. The proposed bandpass /spl Delta//spl Sigma/ modulator is insensitive to time-delay jitter in the digital-to-analog conversion feedback pulse, unlike conventional continuous-time bandpass /spl Delta//spl Sigma/ modulators. The sampling frequency of the proposed /spl Delta//spl Sigma/ modulator can be less than the center frequency of the input narrow-band signal.     

A low-power multi-bit /spl Sigma//spl Delta/ modulator in 90-nm digital CMOS without DEM

Multi-bit sigma-delta modulators are widely used in analog-to-digital conversion especially in the modern deep-submicron CMOS process. As the quantizer resolution of /spl Sigma//spl Delta/ modulators increases, the SNR performance improves. However, the feedback DAC has to maintain high linearity. The general practice to achieve that is to use dynamic element matching (DEM). The methodology proposed in this paper will greatly reduce the complexity or even avoid usage of DEM for multi-bit /spl Sigma//spl Delta/ modulators. The proposed methodology-truncation error shaping and cancellation-reduces the feedback DAC levels for multi-bit quantizers. A prototype was designed in a standard CMOS 90-nm process to demonstrate the proposed methodologies. It achieved targeted performance without DEM at low power consumption with small silicon area.     

A bandpass mismatch noise-shaping technique for /spl Sigma/-/spl Delta/ Modulators

A simple bandpass mismatch noise-shaping technique for /spl Sigma/-/spl Delta/ modulators is presented. This technique uses the data-directed scrambler structure and achieves /spl sim/20 dB improvement in signal-to-noise ratio (SNR) for an oversampling ratio (OSR) of 32. Compared to the technique of bandpass mismatch noise shaping of Lin and Schreier, here, the SNR is improved by /spl sim/ 7dB resulting in a 1-bit improvement in resolution. The selection logic is half the size of the logic in Lin and Schreier and is fully compatible with the low-pass selection logic of Kwan et al.. This compatibility allows implementation of bandpass/low-pass modulator as a single product.     

Continuous-time /spl Delta//spl Sigma/ modulators using distributed resonators

We derive a method for using distributed resonators in /spl Delta//spl Sigma/ modulators and demonstrate these /spl Delta//spl Sigma/ modulators have several advantages over existing /spl Delta//spl Sigma/ modulator architectures. Like continuous-time (CT) /spl Delta//spl Sigma/ modulators, the proposed /spl Delta//spl Sigma/ modulators do not require a high-precision track-and-hold, and additionally can take advantage of the high-Q of distributed resonators. Like discrete-time /spl Delta//spl Sigma/ modulators, the proposed /spl Delta//spl Sigma/ modulators are relatively insensitive to feedback loop delays and can subsample. We present simulations of several types of these /spl Delta//spl Sigma/ modulators and examine the challenges in their design.     

Self-tuning algorithms for high-performance bandpass switched-capacitor /spl Sigma//spl Delta/ modulators

Switched-capacitor high-frequency bandpass /spl Sigma//spl Delta/ modulators could suffer from capacitor mismatch, finite opamp dc gain, and finite opamp bandwidth. These problems make the notch frequency and the quality factor of the zeros of the noise transfer function to deviate from their nominal values, strongly affecting the modulator dynamic range (DR). In order to avoid this situation, two sampled-data algorithms have been developed which allow to self-calibrate the bandpass /spl Sigma//spl Delta/ modulators. They use 3500 gate and 0.043 mm/sup 2/ area and consume power only when they are active, while, when the system is on, they are off and do not interfere with standard operation. The validity of the proposal is demonstrated by a silicon prototype in which the proposed solution allows to guarantee a 75-dB DR performance also under worst case conditions. In the particular case, it allows for the recovery of 3 dB in the SNR for the 200-kHz FM band (from 73 to 76 dB).     

Numerical method for determining the quantization error PDF of single-bit /spl Sigma//spl Delta/ Modulators

Existing models for the quantizer of /spl Sigma//spl Delta/ modulators make assumptions on the probability density function (pdf) of the quantization error, or some other convenient signal of the modulator. In this paper, a method for the determination of this pdf for single-bit /spl Sigma//spl Delta/ modulators is presented. First, a numerical method is proposed in order to solve the simplified equation for the quantization error pdf for first-order systems considering noiseless and noisy dc input signals. Then, it is shown how most practical high-order (>2)/spl Sigma//spl Delta/ modulators, resulting from well-established design methods, can be modeled as first-order systems plus an additive noise source at the input. Hence, their quantization error pdf is analyzed using the proposed method. Simulation results are shown to be in considerable agreement with those of the proposed method.     

Design of low-voltage MOSFET-only /spl Sigma//spl Delta/ modulators in standard digital CMOS technology

A design strategy of low-voltage high-linearity MOSFET-only /spl Sigma//spl Delta/ modulators in standard digital CMOS technology is presented. The modulators use substrate-biased MOSFETs in the depletion region as capacitors, linearized by different compensation techniques. This work shows the design, simulation and measured results of a number of MOSFET-only /spl Sigma//spl Delta/ modulators using different implementations of so called compensated depletion-mode MOS capacitors. The modulators are designed for the demands of speech band applications. The performance of the modulators proves the capability of compensated depletion-mode MOS capacitors to fulfill analog circuit requirements at low supply voltages with reduced processing efforts.     

A triple-mode continuous-time /spl Sigma//spl Delta/ modulator with switched-capacitor feedback DAC for a GSM-EDGE/CDMA2000/UMTS receiver

Time jitter in continuous-time /spl Sigma//spl Delta/ modulators is a known limitation on the maximum achievable signal-to-noise-ratio (SNR). Analysis of time jitter in this type of converter shows that a switched-capacitor (SC) feedback digital-to-analog converter (DAC) reduces the sensitivity to time jitter significantly. In this paper, an I and Q continuous-time fifth-order /spl Sigma//spl Delta/ modulator with 1-bit quantizer and SC feedback DAC is presented, which demonstrates the improvement in maximum achievable SNR when using an SC instead of a switched-current (SI) feedback circuit. The modulator is designed for a GSM/CDMA2000/UMTS receiver and achieves a dynamic range of 92/83/72 dB in 200/1228/3840 kHz, respectively. The intermodulation distance IM2, 3 is better than 87 dB in all modes. Both the I and Q modulator consumes a power of 3.8/4.1/4.5 mW at 1.8 V. Processed in 0.18-/spl mu/m CMOS, the 0.55-mm/sup 2/ integrated circuit includes a phase-locked loop, two oscillators, and a bandgap.     

Hexagonal /spl Sigma//spl Delta/ modulators in power electronics

Design techniques for /spl Sigma//spl Delta/ modulators from communications are applied and adapted to improve the spectral characteristics of high frequency power electronic applications. A high frequency power electronic circuit can be regarded as a quantizer in an interpolative /spl Sigma//spl Delta/ modulator. We review one dimensional /spl Sigma//spl Delta/ modulators and then generalize to the hexagonal sigma-delta modulators that are appropriate to three-phase converters. A range of interpolative modulator designs from communications can then be generalized and applied to power electronic circuits. White noise spectral analysis of sigma-delta modulators is generalized and applied to analyze the designs so that the noise can be shaped to design requirements. Simulation results for an inverter show significant improvements in spectral performance.     

Tunable continuous-time bandpass /spl Sigma//spl Delta/ modulators with fractional delays

An analytical design methodology for continuous-time (CT) bandpass (BP) /spl Sigma//spl Delta/ modulators is presented. Second- and fourth-order tunable continuous time BP /spl Sigma//spl Delta/ modulator design equations are presented. A novel /spl Sigma//spl Delta/ loop architecture, where the traditional CT BP loop filter function is replaced with the filter function with fractional delays, is proposed. Validity of the methodology is confirmed by mixed-signal behavioral simulations.     

80-MHz bandpass /spl Delta//spl Sigma/ modulators for multimode digital IF receivers

Three fully differential bandpass (BP) /spl Delta//spl Sigma/ modulators are presented. Two double-delay resonators are implemented using only one operational amplifier. The prototype circuits operate at a sampling frequency of 80 MHz. The BP /spl Delta//spl Sigma/ modulators can be used in an intermediate-frequency (IF) receiver to combine frequency downconversion with analog-to-digital conversion by directly sampling an input signal from an IF of 60 MHz to a digital IF of 20 MHz. The measured peak signal-to-noise-plus-distortion ratios are 78 dB for 270 kHz (GSM), 75 dB for 1.25 MHz (IS-95), 69 dB for 1.762 MHz (DECT), and 48 dB for 3.84 MHz (WCDMA/CDMA2000) bandwidths. The circuits are implemented with a 0.35-/spl mu/m CMOS technology and consume 24-38 mW from a 3.0-V supply, depending on the architecture.     

1-bit quantiser with rail to rail input range for sub-1 V /spl Delta//spl Sigma/ modulators

A new, fully differential comparator with rail to rail input range is presented. This comparator can be used as a 1-bit quantiser in sub-1 V /spl Delta//spl Sigma/ modulators. The quantiser is laid out in 0.18 /spl mu/m CMOS technology. The post-layout simulation results show that the quantiser is capable of working at 10 MHz with 10 /spl mu/V resolution. This quantiser is successfully used in 0.8 V first-order and second-order fully differential /spl Delta//spl Sigma/ modulators.     

A 10.7-MHz self-calibrated switched-capacitor-based multibit second-order bandpass /spl Sigma//spl Delta/ modulator with on-chip switched buffer

A second-order multibit bandpass /spl Sigma//spl Delta/ modulator (BP/spl Sigma//spl Delta/M) used for the digitizing of AM/FM radio broadcasting signals at a 10.7-MHz IF is presented. The BP/spl Sigma//spl Delta/M is realized with switched-capacitor (SC) techniques and operates with a sampling frequency of 37.05 MHz. The input impulse current, required by the SC input branch, is minimized by the use of a switched buffer without deteriorating the overall system performance. The accuracy of the in-band noise shaping is ensured with two self-calibrating control systems. In a 0.18-/spl mu/m CMOS technology, the device die size is 1 mm/sup 2/ and the power consumption is 88 mW. In production, the BP/spl Sigma//spl Delta/M features at least 78-dB dynamic range and 72-dB peak SNR within a 200-kHz bandwidth (FM bandwidth). The intermodulation (IMD) is -65 dBc for two tones at -11 dBFS. The robustness of the aforementioned performance is demonstrated by the fact that it has been realized with the BP/spl Sigma//spl Delta/M embedded in the noisy on-chip environment of a complete mixed-signal FM receiver.     

Adaptive order reduction scheme for high-order single-bit /spl Delta//spl Sigma/ Modulators

A scheme for achieving adaptive reduction in the order of the loop filter of usual high-order, single-stage, single-bit Delta-Sigma (/spl Delta//spl Sigma/) modulators is proposed in order to improve their performance. The resulting /spl Delta//spl Sigma/ modulators can recover from instability effectively, having also an extended input signal range in comparison to that of the corresponding conventional /spl Delta//spl Sigma/ modulators.     

A 75-dB image rejection IF-input quadrature-sampling SC /spl Sigma//spl Delta/ Modulator

Quadrature sampling of intermediate frequency (IF) signals is subject to the well-known problem of gain and phase mismatches between the in-phase (I) and quadrature (Q) channels. This paper presents an IF-input quadrature-sampling switched-capacitor (SC) /spl Sigma//spl Delta/ modulator that circumvents the I/Q mismatch problem by time-sharing between the I and Q channels the critical circuit components, namely, the sampling capacitor and the capacitor of the first-stage feedback digital-to-analog converter (DAC). In addition, a clocking scheme that is insensitive to I/Q phase imbalance is used. A third-order single-loop 1-bit low-pass modulator has been designed and fabricated in a 0.35-/spl mu/m CMOS process with an active area of 0.57mm/sup 2/. The experimental results show that the modulator achieves an image-rejection ratio (IRR) of greater than 75dB throughout a 200-kHz signal bandwidth.     

A 1-MHz-bandwidth second-order continuous-time quadrature bandpass sigma-delta modulator for low-IF radio receivers

This paper presents a quadrature bandpass /spl Sigma//spl Delta/ modulator with continuous-time architecture. Due to the continuous-time architecture and the inherent anti-aliasing filter, the proposed /spl Sigma//spl Delta/ modulator needs no additional anti-aliasing filter in front of the modulator in contrast to quadrature bandpass /spl Sigma//spl Delta/ modulators with switched-capacitor architectures. The second-order /spl Sigma//spl Delta/ modulator digitizes complex analog I/Q input signals at 1-MHz intermediate frequency and operates within a clock frequency range of 25-100 MHz. The modulator chip achieves a peak signal-to-noise-distortion ratio (SNDR) of 56.7 dB and a dynamic range of 63.8 dB within a 1-MHz signal bandwidth and at a clock frequency of 100 MHz. Furthermore, it provides an image rejection of at least 40 dB. The 0.65-/spl mu/m BiCMOS chip consumes 21.8 mW at 2.7-V supply voltage.     

Improved design method for continuous-time quadrature bandpass /spl Sigma//spl Delta/ ADCs

In continuous-time quadrature bandpass /spl Sigma//spl Delta/ ADCs it is desirable to limit the number of cross-couplings. This can be achieved by implementing the loop as a cascade of complex integrators with only real coefficients. It is shown that this may result in a very poor approximation of the desired noise transfer function, because the effect of the DAC pulse is not taken into account correctly. A simple implementation that solves this problem is proposed.