Dynamic mechanical properties of quinazolone–imide block copolymer

Dynamic mechanical properties have been investigated over the temperature range of?150–360°C for the quinazolone–imide copolymers, prepared by condensation of the amine-terminated quinazolone prepolymer with a stoichiometric quantity of pyromellitic dianhydride or 3,3′,4,4′-benzophenone-tetracarboxilic dianhydride. Both copolymers have, respectively, the low-temperature β-relaxation and the β^*-relaxation, as well as the case of poly(4,4′-oxydiphenylene–pyromellite-imide) (Kapton) examined for comparison. These relaxations seem to contribute to toughness of the copolymers. The α-relaxations for both copolymers occurred at much the same temperature of 320°C, which can be assigned to a large scale segmental motion of the quinazolone chain sequence. The α-peak temperatures shifted into higher temperatures by heat aging. This can be explained in terms of crosslinking in the copolymers, supported by swelling test in hot m-cresol and IR spectroscopy.     

Synthesis of polyurethane–imide (PU–imide) copolymers with different dianhydrides and their properties

This study reports the synthesis of polyurethane–imide (PU–imide) copolymers using 4,4′-diphenylmethane diisocyanate (MDI) polytetramethylene glycols (PTMGs) and different aromatic dianhydrides. Differential scanning calorimetry (DSC) results indicate that PU–imide copolymers had two phase structures containing four transition temperatures (T_gs, T_ms, T_gh and T_mh). However, only PU–imide copolymers were formed by soft PTMG(2000) segments possessing a T_ms (melting point of soft segment). When different aromatic dianhydrides were introduced into the backbone chain of the polyurethane, although the T_gs (glass transition temperature of the soft segment) of some of PU–imide copolymers did not change, the copolymers with long soft segments had low T_gs values. The T_gh (glass transition temperature of hard segment) values of PU–imide copolymers were higher than that of polyurethane (PU). In addition, the high hard segment content of PU–imide copolymer series also had an obvious T_mh (melting point of hard segment). According to thermogravimetric analysis (TGA) and differential thermogravimetric analysis (DTGA), the PU–imide copolymers had at least two stages of degradation. Although the T_di (initial temperature of degradation) depended on the hard segment content and the composition of hard segment, the different soft segment lengths did not obviously influence the T_di. However, PU–imide copolymers with a longer soft segment had a higher thermal stability in the degradation temperature range of middle weight loss (about T_d 5%–50%). However, beyond T_d 50% (50% weight loss at temperature of degradation), the temperature of degradation of PU–imide copolymers increased with increasing hard segment content. Mechanical properties revealed that the modulus and tensile strength of PU–imide copolymers surpassed those of PU. Wide angle X-ray diffraction patterns demonstrated that PU–imide copolymers are crystallizable. © 1999 Society of Chemical Industry     

Study on synthesis and thermal properties of polyurethane–imide copolymers with multiple hard segments

Different multiple hard segment polyurethane–imide copolymers (MHPUI) were synthesized and characterized. FTIR spectroscopy confirmed the characteristic absorption of the MHPUI copolymer. The difference in the imide group FTIR absorption bands in different MH segment PUI copolymers was found in this study and was explained by the different MH segment types, hard segment contents, and hard segment rigidity with different interactions of the molecular chains. The hard segment interaction in MHPUI with an increase of the structure rigidity of the short hard segments is strengthening. The DSC analysis revealed that the glass‐transition temperature of the soft segment of PUI rose in value from ?42 to ?3.4°C with the introduction of MH and different MH segments. The DSC results suggest that the soft segment is more compatible with the hard segment rigidity increase. The TGA results showed the hard segment structure symmetry has a more important role in the MHPUI thermal stability. Every sample containing symmetrical structure short hard groups (4,4′‐diphenylmethane diisocyanate or 4,4′‐diaminodiphenylmethane) is more thermally stable than that with worse symmetry structure groups (2,4‐toluene diisocyanate or 3,3′‐dichloro‐4,4′‐diamino‐diphenylmethane). The three‐step mechanism of PUI thermal degradation was further verified by the TGA study. The thermally unstable group was confirmed as urethane or a urea–urethane segment. The TGA results showed that MHPUI copolymers with higher separation of the soft–hard phase have higher thermal stability. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2206–2215, 2002     

Preparation and properties of imide–pyrrone copolymers

Two series of copolymers containing imidazopyrrolone (pyrrone) and imide groups were prepared by solution polymerization. Thin films of the copolymers showed a general increase in the tangent modulus and a decrease in elongation with increasing pyrrone content. The copolymers were more resistant to degradation by strong acids and bases than the corresponding polyimides. The thermal stabilities of the copolymers in air improved with increasing imide content, while the thermal stabilities in a vacuum improved with increasing pyrrone content. These copolymers represent a way to combine the desirable properties of both classes of homopolymers.     

Hexamethyl cyclotrisiloxane–styrene block copolymers and their chemical composition

Triblock copolymers of hexamethyl cyclotrisiloxane (D₃) and styrene were synthesized by first preparing “living” species of polystyrene dianion followed by polymerization of D₃. The chain lenght of polymeric blocks could be controlled in a predictable fashion leading to a central hard block of polystyrene and the two end segments of amorphous polydimethylsiloxane having narrow molecular weight distribution, were characterized by gel permeation chromatography. The chemical composition of block copolymers was determined by silicon analysis and infrared and nuclear magnetic resonance spectra. Thermal aging of block copolymers at 150, 200, and 300°C was also discussed.     

Melt polymerization of copoly(ethylene terephthalate–imide)s and thermal properties

Copoly(ethylene terephthalate–imide)s (PETI) were prepared by melt polycondensation of bis(2-hydroxyethyl)terephthalate (BHET) and imide containing oligomer, i.e., 4,4′-bis[(4-carbo-2-hydroxyethoxy)phthalimido]diphenylmethane(BHEI). The apparent rate of poly-condensation reaction was faster than that of homo poly(ethylene terephthalate) (PET) due to the presence of imide units. The PETI copolymers with up to 10 mol % of BHEI unit in the copolymer showed about the same molecular weight and carboxyl end group content as homo PET prepared under similar reaction conditions. The increase in T_g of copolymer was more dependent on molar substitution of BHEI than on substitution of BHEN, reaching 91°C with 8 mol % BHEI units in the copolymer from T_g = 78.9°C of homo PET. In the case of PETN copolymer, 32 mol % of bis(2-Hydroxyethyl)naphthalate (BHEN) units gave T_g of 90°C. The maximum decomposition temperature of PETI copolymer was about the same as that of homo PET by TGA analysis. The char yield at 800°C was higher than that of homo PET. © 1996 John Wiley & Sons, Inc.     

Synthesis of thermostable nomex copoly(amide–imide) and their properties

Thermostable Nomex copoly(amide–imide)s with inherent viscosity of 0.72–1.31 dL/g were synthesized by reacting diacid-terminated Nomex prepolymer with various diisocyanate-terminated polyimide prepolymers. The polyimide prepolymer was prepared by using 4,4′-diphenylmethane diisocyanate to react with 3,3′,4,4′-benzophenonetetracarboxylic dianhydride, pyromellitic dianhydride, or 3,3′,4,4′-sulfonyl diphthalic anhydride using a direct one pot method in order to improve their solubility. The copolymers, except B-1, P-1, P-2, D-1, and D-2, could be dissolved in N, N-dimethylacetamide +5% lithium chloride at room temperature or dimethyl sulfoxide at high temperature but were not soluble in N,N-dimethylformamide or pyridine. The solubility is considered to be related to their crystallinity. Those copolymers with crystalline structure displayed poor solubility. All the Nomex copoly(amide–imide)s had glass transition temperatures in the range of 223–352°C and showed a 10% weight loss temperature of 438–574°C in air and 441–585°C in nitrogen atmosphere. The tensile strength, elongation at break, and initial modulus of polymer films ranged 63–118 MPa, 4–9% and 1.67–2.53 GPa, respectively. From the X-ray diffraction studies, copolymers of B-1, P-1, P-2, D-1, and D-2 with high content of PmIA showed a crystalline structure, but the others only displayed an amorphous morphology. © 1996 John Wiley amp; Sons, Inc.     

Synthesis and characterization of rubbery highly fluorinated siloxane–imide segmented copolymers

The synthesis and characterization of a series of poly(siloxane–imide) block (or segmented) copolymers obtained by copolymerization of amine‐terminated polydimethylsiloxane with fluorinated aromatic compounds containing anhydride and amine functionality are reported. New fluorinated block copolymers have been synthesized to obtain organophilic polyimides potentially interesting for molecular membrane separations. The new aspects of this work relative to the literature are (1) a comparison of solution and solid‐state approaches in the imidization step to generate the target poly(siloxane–imide) copolymers and (2) exploration of new compositions involving fluorinated aromatic polymers derived from added diamine compounds. It is shown that the copolymer properties can be tailored from glassy to rubbery materials by varying the amount and the type of oligosiloxane used; the transition between glassy and rubbery properties is characterized at a siloxane content of 60 wt%. As a main result, it is shown that the solid‐state approach for inducing the cyclo‐imidization step is the more efficient one for synthesizing polymers with good mechanical properties, when the amount of siloxane block is increased in the copolymer series. Physical and chemical methods (thermogravimetric analysis, Fourier transform infrared spectroscopy, viscosity measurements) were used to characterize the copolymer properties obtained according to the two different synthesis routes. The obtained siloxane–imide copolymers are well soluble in a large variety of moderately polar solvents and exhibit very good thermal stability up to 400 °C. Hence the prepared copolyimides would seem to be promising candidates as organophilic membranes as well as gas permeation membranes. © 2012 Society of Chemical Industry     

Preparation,characterization, and properties of cellulose–polyacrylamide graft copolymers

Graft copolymers of acrylamide on cellulose materials (α‐cellulose 55.8%, DP 287.3) obtained from Terminalia superba wood meal and its carboxymethylated derivative (DS 0.438) were prepared using a ceric ion initiator and batch polymerization and modified batch polymerization processes. The extent of graft polymer formation was measured in graft level, grafting efficiency, molecular weight of grafted polymer chains, frequency of grafting as a function of the polymerization medium, and initiator and monomer concentrations. It was found that the modified batch polymerization process yielded greater graft polymer formation and that graft copolymerization in aqueous alcohol medium resulted in enhanced levels of grafting and formation of many short grafted polymer chains. Viscosity measurements in aqueous solutions of carboxymethyl cellulose‐g‐polyacrylamide copolymer samples showed that interpositioning of polyacrylamide chains markedly increased the specific viscosity and resistance to biodegradation of the graft copolymers. The flocculation characteristics of the graft copolymers were determined with kaolin suspension. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 913–923, 2003     

Preparation of Pt–Ru–Co trimetallic nanoparticles and their electrocatalytic properties

Ternary Pt–Ru–Co nanoparticles are prepared by microemulsions procession. These resulting materials showed a homogenous alloy structure, the mono-dispersion and an average diameter of 2.7 ± 0.6 nm with a narrow particle size distribution. The composition of Pt–Ru–Co nanoparticles can be controlled by adjusting the initial metal salt solution and preparation conditions. Pt–Ru–Co ternary metallic nanoparticles can enhance catalytic activity towards methanol oxidation compared to Pt–Ru bimetallic nanoparticles.     

Synthesis and properties of some novel,soluble and light‐coloured,aromatic poly(amide–imide) copolymers

A new type of tetraimide‐dicarboxylic acid (I) was synthesized starting from the ring‐opening addition of m‐aminobenzoic acid (m‐ABA), 4,4′‐oxydiphthalic anhydride (ODPA) and 4,4′‐methylenedianiline (MDA) at a 2:2:1 molar ratio in N‐methyl‐2‐pyrrolidone (NMP), followed by cyclodehydration to the diacid I. A series of soluble and light‐coloured poly(amide–imide–imide)s (III_a–j) was prepared by triphenyl phosphite‐activated polycondensation from the tetraimide‐diacid I with various aromatic diamines (II_a–j). All films cast from DMAc had cutoff wavelengths shorter than 400 nm (376–393 nm) and had b* values between 20.46 and 40.67; these polymers were much lighter in colour than those of the corresponding trimellitimide series. All polymers were readily soluble in a variety of organic solvents such as NMP, N,N‐dimethylacetamide, dimethyl sulfoxide, and even in the less polar m‐cresol and pyridine. Compared with those of corresponding ODPA–MDA polyimide, the solubilities of poly(amide–imide–imide)s III_a–j were greatly improved. Polymers III_a–j afforded tough, transparent, and flexible films, which had tensile strengths ranging from 82 to 105 MPa, elongations at break from 8 to 14%, and initial moduli from 2.0 to 2.2 GPa. The glass transition temperature of polymers were recorded at 255–288 °C. They had 10% weight loss at a temperature above 540 °C and left more than 60% residue even at 800 °C in nitrogen. © 2002 Society of Chemical Industry     

Synthesis and thermal properties of poly(urethane‐imide)

The synthesis and thermal properties of thermoplastic poly(urethane‐imide) (PUI) resins were studied. Model reaction studies on the reactions of 4,4′‐diphenylcarbamatodiphenylmethane and 4,4′‐diisocyanatodiphenylmethane with phthalic anhydride were performed. We found that the reaction of anhydrides with urethane groups could take place under certain reaction conditions. According to the model reaction studies, N‐2‐methyl‐pyrrolidone was employed as a solvent, and no catalyst was used in the polymerization. To restrain the side reaction of anhydrides with urethane groups, we adopted a two‐step chain‐extending procedure in a chain‐extending reaction. The inherent viscosity of PUI was 0.83–0.99 dL/g. The prepared polymers not only exhibited improved solubility in organic solvents but also formed flexible films. Thermogravimetric analysis showed that PUI exhibited a two‐step thermal weight‐loss pattern. The first step of the thermal degradation of PUI was attributed to the thermooxidizing cleavage of weak and labile linkage, such as urethane groups, isopropylidene, and methylene, except for imide rings. The polymer inherent viscosity decreased sharply during the first step of thermal degradation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 773–781, 2001     

Phosphorus‐containing poly(ester‐imide)–polydimethylsiloxane copolymers

New phosphorus‐containing poly(ester‐imide)‐polydimethylsiloxane copolymers were prepared by solution polycondensation of 1,4‐[2‐(6‐oxido‐6H‐dibenz < c,e > < 1, 2 > oxaphosphorin‐6‐yl)]naphthalene‐bis(trimellitate) dianhydride with a mixture of an aromatic diamine (1,3‐bis(4‐aminophenoxy)benzene) and α,ω‐bis(3‐aminopropyl)oligodimethylsiloxane of controlled molecular weight, in various ratios. Poly(amic acid) intermediates were converted quantitatively to the corresponding polyimide structures using a solution imidization procedure. The polymers are easily soluble in polar organic solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylformamide, as well as in less polar solvents such as tetrahydrofuran. They show good thermal stability, the decomposition temperature being above 370 °C. The glass transition temperatures are in the range 165–216 °C. Solutions of the polymers in N‐methyl‐2‐pyrrolidone exhibit photoluminescence in the blue region. Copyright © 2010 Society of Chemical Industry     

Preparation and thermal properties of polyethylene terephthalate/huntite–hydromagnesite composites

In this report, it was aimed to the improve thermal stability of polyethylene terephthalate (PET) by adding huntite/hydromagnesite minerale. PET/huntite/hydromagnesite composites were prepared by adding various proportions of huntite/hydromagnesite to PET. The chemical structures of the composites were characterized by Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) analysis. Thermal properties of the composites were determined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Glass‐transition temperatures and char yields increased with the increase of the huntite/hydromagnesite content in the composites. The surface morphologies of the composites were investigated by a scanning electron microscopy. The obtained results proved that the composite system is more thermally stable than the pure PET itself. POLYM. COMPOS., 37:3275–3279, 2016. © 2015 Society of Plastics Engineers     

Syntheses,structure, reactivity,and thermal properties of epoxy–imide resin cured by phosphorylated triamine

A new phosphorylated epoxy–imide polymer was obtained using diimide–diepoxide (DIDE) cured with tris(3-aminophenyl)phosphine oxide (TAPO). In addition, compositions of the synthesized diimide diepoxide (DIDE), Epon 828, and DEN 438 with common curing agents, e.g., 4,4′-diaminodiphenyl ether (DDE) and 4,4′-diaminodiphenylsulfone (DDS), were compared as to curing reactivity and heat and flame retardation with that of tris(3-aminophenyl)phosphine oxide. The reactivities of those curing agent toward the three kinds of epoxy resins, as measured by differential scanning calorimetry (DSC), were in the order DDE > TAPO > DDS. Through thermal gravimetric analysis (TGA), the thermal and flame resistances of epoxy were confirmed in this study as capable of being significantly improved through introduction of imide and phosphorus groups into the epoxide structure. © 1996 John Wiley & Sons, Inc.     

氢气刻蚀法制备Pt/CNTs复合材料及其热稳定性

采用碳化硅高温热分解法制备整齐排列的直立碳纳米管阵列,并对其进行Pt金属粒子修饰,通过氢气刻蚀法可以将闭口碳纳米管阵列开口,并将Pt纳米粒子嵌入到碳纳米管中。这种新型Pt/CNTs复合材料具有独特的电子限域效应,有助于抑制金属催化剂的烧结,对提高其后续催化活性和应用性能有着重要意义。     

Benzoxazine–epoxy copolymers: effect of molecular weight and crosslinking on thermal and viscoelastic properties

Bisphenol‐A‐based benzoxazine was copolymerized with epoxy and chain‐extended epoxies in order to study the effect of molecular weight on cured resin properties. Cure behaviour of the copolymers was studied using differential scanning calorimetry, which indicated a single exothermic curing peak at 248 °C. Dynamic mechanical thermal analysis was used to study the viscoelastic properties of the cured resins. A decrease in tan δ peak position and an increase in storage modulus and tan δ peak height were observed due to chain extension. Higher char yield was observed for the copolymer chain extended with tetrabromobisphenol‐A. Copyright © 2005 Society of Chemical Industry     

Preparation and thermal properties of resole‐type phenol resin–clay nanocomposites

Resole‐type phenol resin–clay nanocomposites have been prepared successfully by melt compounding phenol resin with organophilic clay. In the resulting phenol resin–clay nanocomposite, the silicate layers of the clay were exfoliated and dispersed as monolayers. The nanocomposite exhibited higher long‐term heat resistance when compared with unmodified phenol resin. It was surmised that the silicate layers of the clay acted as barriers to oxygen penetration into the resin, as the degree of heat degradation of the nanocomposite was much lower than that of the straight phenol resin. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3236–3240, 2006     

酰胺基卟啉化合物的制备、表征及热分析

5-(4-氨基)苯基-10,15,20-三苯基卟啉(MATPP)与棕榈酸在CH2Cl2中直接反应,得到一种新型不对称酰胺基卟啉5-(4-棕榈酸酰亚胺基)苯基-10,15,20-三苯基卟啉(PITPPH2),利用紫外-可见光谱、红外光谱、核磁共振氢谱、元素分析等测试方法对化合物的结构加以确认。热分析表明,卟啉PITPPH2从200℃开始分解,具有较高的热稳定性。