Synthesis and rheological properties of soluble poly(hydroxyethyl methacrylate) and some copolymers

Methods to synthesise soluble poly(2-hydroxyethyl methacrylate) (PHEMA) with varying molar mass were developed. Conversions over 90% were achieved without losing solubility. Steady state tests (range 0.01–590 Pa) and oscillatory tests (range 0.001–40 Hz) were carried out on 40% solutions in dimethyl formamide using a Carri-Med rheometer. Only PHEMA having molar mass over 500000 showed significant shear thinning and viscoelastic properties. The copolymers of 2-hydroxyethyl methacrylate (HEMA) with n-butyl acrylate (BA) and 2-hydroxypropyl acrylate (HPA) showed higher viscosities and viscoelastic properties compared with PHEMA homopolymer prepared under identical conditions. Also, viscosity and viscoelasticity increased with increase in acrylate content in the initial mixture. This was attributed to the higher molar mass of copolymers, which resulted from faster polymerisation rates owing to the inclusion of relatively highly reactive acrylates. However, in the case of HEMA : BA copolymers, first, the viscosity and viscoelasticity increased with increasing BA content and then dropped again, giving a maximum around HEMA : BA 75 : 25. This anomaly was explained by taking the effects of changes in inter-and intra-molecular hydrogen bonding as well as conformational differences caused by inclusion of BA in the PHEMA chain into account.     

Synthesis and properties of well-defined poly (dimethylsiloxane)-b-poly(2-hydroxyethyl methacrylate) copolymers

Block copolymers containing dimethyl siloxane and 2-hydroxyethyl methacrylate sequences were synthesized by group transfer polymerization (GTP) of 2-trimethylsilyloxyethyl methacrylate (TMS-HEMA) using silyl ketene acetal terminated poly(dimethylsiloxane) (PDMS) as macroinitiator, followed by hydrolysis of TMS-HEMA to HEMA. The block copolymers were obtained with controlled molecular weight and narrow molecular weight distribution. Trimethylsilyl groups in the P(TMS-HEMA) block could be selectively hydrolyzed without cleaving Si-O bond in PDMS block. The block copolymers formed micelles in methanol, the effective diameters (R_h) of which were in the range of 78 – 110 nm with narrow distribution by dynamic light scattering (DLS). The TEM image showed micelles with a spherical shape. Received: 10 May 2001/Revised version: 23 August 2001/Accepted: 24 August 2001     

Preparation and characterization of poly(vinyl alcohol-co-methyl methacrylate) copolymers

Summary An investigation is presented of the preparation and characterization of poly(vinyl alcohol-co-methyl methacrylate) copolymers which can be used for the preparation of novel membranes. These polymers were prepared by copolymerization of vinyl acetate and methyl methacrylate by -irradiation, followed by methanolysis of the produced copolymers. IR and ¹H-NMR studies established the structure of the copolymers.On sabbatical leave from the Department of Chemical Engineering, Sung Kyun Kwan University, Suwon 170-00, Republic of Korea.     

Stereocomplex formation in polybutadiene-syndiotactic poly(methyl methacrylate) block copolymers blended with isotactic poly(methyl methacrylate)

Summary The process of stereocomplexation in blends of isotactic poly(methyl methacrylate)s and polybutadiene-syndiotactic poly(methyl methacrylate) diblock copolymers was studied by differential scanning calorimetry as a function of molar mass of the constituents, annealing time and temperature. The amount of complex formed is dependent on these three parameters, while the temperature of decomposition of the complex is only dependent on the annealing temperature. Complex formation can be observed in blends containing a copolymer with a very low molar mass syndiotactic poly(methyl methacrylate) block (Mn=700). In contrast to homopolymer blends, for which two endotherms of decomposition were generally reported, only one endotherm is observed for copolymer-homopolymer blends. This behavior is attributed to the elastomer block.     

Copolymer electron resists: poly(stryene-methyl methacrylate) copolymers

The factors influencing electron beam sensitivity are reviewed. The variation of electron beam sensitivity and constrast are reported for a series of random copolymers of styrene and methyl methacrylate. Data are also presented for an alternating copolymer of styrene and methyl methacrylate. This study indicates the effects which arise when a negative resist material, polystyrene, is incorporated into a positive resist material, poly(methyl methacrylate).     

The reinforcement of polystyrene and poly(methyl methacrylate) interfaces using alternating copolymers

Asymmetric double cantilever beam studies are presented that document the ability of alternating copolymers to strengthen a polymer/polymer interface. For polystyrene/poly(methyl methacrylate) interfaces, these results show that the alternating copolymer is the least effective sequence distribution of a linear copolymer at strengthening the polystyrene/poly(methyl methacrylate) interface, where the copolymers that are compared all have similar molecular weight and composition. The results also demonstrate that the effect of copolymer molecular weight on the ability of the copolymer to strengthen an interface is controlled by the balance between the increased entanglements and decreased miscibility of the copolymer with the homopolymers with increasing molecular weight.     

Graft copolymers of poly(methyl methacrylate) backbone and poly(propylene oxide-b-ethylene oxide) branches

Summary Two mono-functional macromonomers of poly (propylene oxide-b-ethylene oxide) were synthesized by reaction with methacryloyl chloride. The macromonomers have the same molecular weight and ratio of ethylene oxide and propylene oxide sequences. The reactive methacrylate group can be linked to the ethylene oxide (BuPPOPEO) or to the propylene oxide (BuPEOPPO). These macromonomers showed self-gelling in one week even at low temperature and under a dry atmosphere. Graft copolymers were obtained by reaction of these macromonomers with methyl methacrylate upon free-radical initiation and they were characterized by GPC, VPO, IR and ¹H NMR spectra.     

Miscibility of poly(methoxymethyl methacrylate) and poly(methylthiomethyl methacrylate) with poly(methyl methacrylate)

Summary Poly(n-propyl methacrylate) is known to be immiscible with poly(methyl methacrylate) (PMMA). However, we have found that poly(methoxymethyl methacrylate) is miscible with PMMA, indicating the importance of ether oxygen atoms in achieving miscibility. On the other hand, poly(methylthiomethyl methacrylate) is immiscible with PMMA.     

Surface properties for poly(perfluoroalkylethyl methacrylate)/poly(n-alkyl methacrylate)s mixtures

A poly(perfluoroalkylethyl methacrylate) and a series of poly(n-alkyl methacrylate)s such as poly(methyl methacrylate), poly(ethyl methacrylate), and poly(n-butyl methacrylate) were prepared and used to investigate the surface properties of polymer mixtures containing a fluorinated homopolymer and a nonfluorinated homopolymer and the effect of the side-chain length of poly(n-alkyl methacrylate) on the surface free energy for the polymer mixtures. Contact angles were measured for the surfaces of polymer mixtures by varying the concentration of poly(perfluoroalkylethyl methacrylate). From the contact angle data, it can be inferred that most of the poly(perfluoroalkylethyl methacrylate) added to poly(n-alkyl methacrylate)s is located in the outermost layer of polymer-mixture surface. Surface free energies for the outermost surfaces of polymer mixtures were calculated from the contact angle data using Owen and Wendt's equation. The decrease in the surface free energy for the polymer mixture with the poly(perfluoroalkylethyl methacrylate) addition is more pronounced as the side-chain length of poly(n-alkyl methacrylate) decreases. Due to the steric effect of the side chain of poly(n-alkyl methacrylate), the arrangement of the perfluoroalkylethyl group of poly(perfluoroalkylethyl methacrylate) to the air side is considerably hindered. The ESCA analysis of atomic compositions of the surface for the polymer mixture verified that poly(perfluoroalkylethyl methacrylate) is preferentially arranged and concentrates at the polymer mixture–air interface. The results of functional group compositions obtained by ESCA showed that the functional group composition of  CF₃ for the outermost layer has a more important effect on the surface free energy than that of  CF₂ and confirmed the hindrance of the arrangement of perfluoroalkylethyl group to the air side by the side chain of poly(n-alkyl methacrylate). © 1994 John Wiley & Sons, Inc.     

Viscoelastic properties of poly(ethylene-co-styrene) copolymers

The viscoelastic properties of narrowly distributed linear poly(ethylene-co-styrene) copolymers with different mole fractions of styrene (x_S = 0–20.5 mol %) and molecular weights (M_w = 64–214 kg/mol) were analyzed in the molten state at different temperatures by means of oscillatory rheometry. Analyzing the thermorheological properties of the polymers, we found that the time temperature superposition principle is fulfilled. The corresponding shift factors follow up to 16.5 mol % of styrene units the Arrhenius behavior of neat polyethylene. For a styrene content of about 20 mol %, the polymers no longer crystallize and a transition from Arrhenius to WLF behavior of pure polystyrene was observed. The zero shear viscosity, η₀, of the polymers was derived from the mastercurves. The determination of the plateau modulus by the well-known tan δ-min criterion is not possible due to the beginning crystallization in the corresponding temperature range. An approximate calculation of this value is based on the characteristic relaxation time λ_x = 1/ω_x, corresponding to the crossover of G′ and G′. Indeed, the characteristic modulus G_px calculated as η₀/λ_x is a good approximation for the plateau modulus G_p. The viscosity–molecular weight and relaxation time–molecular weight scaling relations were established for three copolymers with different molecular weights and nearly the same styrene content. For both material parameters, the scaling exponent is around 3.4, confirming the linear architecture of the investigated polymers. The mixing rules describing the change of such material parameters like zero shear viscosity or plateau modulus independent of styrene content are of logarithmic linear character using the weight fraction of styrene units instead of the mole fraction. The relations found allow the prediction of melt state properties for polymers with arbitrary styrene content. In the future, when catalysts with sufficient activity for the synthesis of high styrene content copolymers are available, these predictions will have to be checked. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65:209–215, 1997     

Well-defined poly(2-hydroxyethyl methacrylate) and its amphiphilic block copolymers via acidolysis of anionically synthesized poly(2-vinyloxyethyl methacrylate)

Summary A novel approach to a well-defined poly(2-hydroxyethyl methacrylate) [poly(HEMA)] and to its amphiphilic block copolymers was developed. The selective living anionic polymerization of the methacryloyl group of the bifunctional monomer 2-vinyloxyethyl methacrylate (VEMA) generated a functional polymer with a controlled molecular weight and a narrow molecular weight distribution (M_w/M_n= 1.05–1.09). This polymer is very stable under normal conditions. Being soluble in the common organic solvents, its characterization could be carried out easily. The unreacted vinyl groups in the side chains of the resulting polymer were further reacted with hydrochloric acid. This acidolysis changed poly(VEMA) to a well-defined poly(HEMA). In addition, the anionic block copolymerization of VEMA with styrene or methyl methacrylate also proceeded smoothly, generating the corresponding block copolymers. After acidolysis, these copolymers were turned into amphiphilic block copolymers containing a hydrophilic poly(HEMA) block. Received: 22 June 2001/Revised version: 15 August 2001/Accepted: 15 August 2001     

Synthesis and characterization of poly(dimethylamino ethyl methacrylate)–poly(ethylene oxide)–poly(dimethylamino ethyl methacrylate) triblock copolymers

Novel, monodispersed, and well‐defined ABA triblock copolymers [poly(dimethylamino ethyl methacrylate)–poly(ethylene oxide)–poly(dimethylamino ethyl methacrylate)] were synthesized by oxyanionic polymerization with potassium tert‐butanoxide as the initiator. Gel permeation chromatography and ¹H‐NMR analysis showed that the obtained products were the desired copolymers with molecular weights close to calculated values. Because the poly(dimethylamino ethyl methacrylate) block was pH‐ and temperature‐sensitive, the aqueous solution behavior of the polymers was investigated with ¹H‐NMR and dynamic light scattering techniques at different pH values and at different temperatures. The micelle morphology was determined with transmission electron microscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of polycarbonate‐poly(methyl methacrylate) graft copolymers by polycondensation of macromonomers

Polycarbonates (PCs) having poly(methyl methacrylate)s (PMMAs) as graft chains were prepared by the polycondensation of PC oligomers bearing chloroformate groups as the end groups with dicarboxyl‐terminated PMMA macromonomers, which were prepared by the radical polymerization of methyl methacrylate in the presence of thiomalic acid as a chain transfer. The resulting PC‐PMMA graft copolymers were transparent in comparison with PC/PMMA blend polymers, and had higher Vickers hardness than blend polymers when both of them had the same PMMA content. According to the results of multiple regression analysis, the improvement of Vickers hardness was conducive to length (46%) and number (37%) of PMMA branches. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2670–2675, 2001     

Block copolymers comprising poly(ethylene oxide) and poly(hydroxyethyl methacrylate) blocks: synthesis and characterization

Monofunctional poly(ethylene oxide) macroinitiators with a molecular weight of 2000, 5000, 10?000, 20?000 and bifunctional poly(ethylene oxide) macroinitiators with a molecular weight of 20?000 were used for the atom transfer radical polymerisation (ATRP) of hydroxyethyl methacrylate (HEMA) in ethylene glycol as a solvent. The polymerisation proceeds in a controlled way up to high conversions. The molecular weight of the obtained copolymers increases linearly with conversion. A high rate of polymerisation was observed for the ATRP of HEMA. The effect of the poly(ethylene oxide) moiety on the course of the reaction is limited to solvating effects. The surface analysis of poly(ethylene oxide)/poly(hydroxyethyl methacrylate) block copolymers by means of atomic force microscopy in tapping mode using phase imaging shows phase separated domains with characteristic features related to the volume fraction of the respective blocks.     

Surface modification of poly(vinyl chloride) with poly(methyl methacrylate)/poly(dimethyl siloxane) graft copolymers

X-ray photoelectron spectroscopy is used to study the surface segregation of siloxane in dilute blends of poly(methyl methacrylate)/poly(dimethyl siloxane) graft copolymers in poly(vinyl chloride)(PVC). The graft copolymers are found to be extremely efficient surface modifiers, which form, when added in amounts of 0.5% or more, a continuous siloxane overlayer on the surface of PVC. © 1995 John Wiley & Sons, Inc.     

Shape memory behavior of poly(methyl methacrylate)-graft-poly(ethylene glycol) copolymers

This paper describes a shape memory behavior of graft copolymers poly(methyl methacrylate)-graft-poly(ethylene glycol) (PMMA-g-PEG). In shape memory test, the sample was deformed from its original shape to a temporary shape above glass transition temperature (T_g), cooled below T_g to fix the temporary shape, and subsequently heated above T_g for spontaneous recovery to the original shape. By grafting PEG onto PMMA backbone, shape memory ability was drastically enhanced than PMMA homopolymer. The shape recovery ratio was decreased with the increase in the shape deformation temperature. With considering a good miscibility of backbone and side chain in PMMA-g-PEG, this shape memory ability may be related to a physically cross-linked network structure by chain entanglement of the comb-like graft copolymer. Stress relaxation measurements were investigated in order to confirm the effect of the graft chains on the shape memory behavior.     

The limits of linear viscoelasticity in poly(methyl methacrylate) and poly(ethyl methacrylate)

The limit of linear viscoelasticity is determined for poly(methyl methacrylate) (PMMA) and poly(ethyl methacrylate) (PEMA) in uniaxial tension creep over the temperature range of 20° to T_g ?10°C. The time span covered is from 10 to 1000 sec. The linear limit is defined as the point at which the creep compliance deviates by more than 1% from its mean value in the linear viscoelastic range. For both materials, the stress limit of linear viscoelasticity falls to a minimum or plateau level at a temperature below T_g. It is suggested that the β-mechanism plays an important role in the existence of this minimum.     

Dilute solution properties of poly(benzyl methacrylate)

A series of fractions of poly(benzyl methacrylate) have been prepared with weight-average molecular weights ranging from 0.19 × 10⁶ to 1.74 × 10⁶ g/mol. A theta temperature of 73.2°C was obtained from phase separation studies in cyclopentanol. Intrinsic viscosities have been measured in toluene and methyl ethyl ketone over a range of temperatures, as well as under theta conditions. Unperturbed dimensions and their temperature coefficient have been determined by a number of procedures. A value for the polymer solubility parameter has been calculated from the enthalpy parameter obtained from phase separation data.     

Miscibility of poly(methoxymethyl methacrylate) and poly(methylthiomethyl methacrylate) with poly(styrene-co-acrylonitrile) and poly(p-methylstyrene-co-acrylonitrile)

The miscibility of poly(methoxymethyl methacrylate) (PMOMA) and poly(methylthiomethyl methacrylate) (PMTMA) with poly(styrene-co-acrylonitrile) (SAN) and poly(p-methylstyrene-co-acrylonitrile) (pMSAN) was studied by differential scanning calorimetry. PMOMA is miscible with SAN having an acrylonitrile (AN) content around 30 wt %. However, PMOMA is immiscible with any of the pMSAN having AN contents between 9 and 36 wt % and with pMSAN having AN contents between 19 and 34 wt %. The miscibility of the blends enables the evaluation of various segmental interaction parameters.