Engineering plastics from lignin. XVII. Effect of molecular weight on polyurethane film properties

A series of five fractions with number average molecular weights (M?_n) between 1500 and 10,000 daltons were isolated from a Kraft hydroxypropyl lignin (HPL). From ¹H-NMR and UV analysis the chemical properties of the HPLs were found to vary slightly with molecular weight. The hydroxyl content decreased while the glass transition temperature (T_g) increased as the HPL molecular weight increased. The Fox-Flory equation adequately described the M?_n vs. T_g relationship. The HPL fractions were used as polyols for the preparation of solvent-cast polyurethane networks (PU) in film form. The T_g of the PUs increased from 40° to 120°C as the M?_n of the polyol rose from 1500 to 10,000 daltons. The molecular weight between crosslinks (M?_c) of the networks was determined by swelling. An observed decrease in M?_c with an increase in M?_n was related to the functionality of the system. The strength properties of films prepared from fractionated HPLs were superior to those prepared from nonfractionated HPLs.     

Engineering plastics from lignin. VII. Structure property relationships of poly(butadiene glycol)-containing polyurethane networks

Hydroxypropyl lignin-based thermosetting polyurethanes containing polybutadiene (PBD) glycol soft segments (M_n of 2800 g M^?1) were synthesized with excess hexamethylene diisocyanate (HDI) and tolylene diisocyanate (TDI) by solution casting. Miscibility of the glycol with the lignin derivative was found to be poor as expected, and phase separation between the two polyol components in polyurethanes was detected by thermal and mechanical analysis, and by electron microscopy. This study examines the effect of concentration of polybutadiene glycol on the thermal and mechanical properties of the polyurethanes. The two-phase network system displayed significantly different properties than either the poly(ethylene glycol)-containing polyurethanes or their soft segment-free counterparts described previously. Macrophase separation was observed at nearly all degrees of mixing and was found to affect thermal and mechanical properties. The glass transition temperature (T_g) of the lignin phase in the TDI-based networks increased with poly(butadiene glycol) content rising from 3.6 to 71.4% of polyurethane, and this was attributed to the employment of a constant diisocyanate weight fraction which gave rise to a variable NCO/OH ratio and crosslink density. Distinct phase separation was evidenced by scanning electron microscopy (SEM) at above 3.6 and 7.1% glycol content for HDI- and TDI-based films, respectively. The polyurethane films behaved like rubber-toughened lignin networks when PBD was the discrete phase, and like lignin-reinforced rubber when the lignin derivative was discrete. This behavior was evidenced by the Young's modulus decreasing from 2000 to 50 MPa and ultimate strain rising from 6 to greater than 150%, with soft segment content increasing from 0 to 71.4%.     

Engineering plastics from lignin. VI. Structure–property relationships of PEG-containing polyurethane networks

Hydroxypropyl lignin-based thermosetting polyurethanes were synthesized with excess hexamethylene diisocyanate (HDI) and tolylene diisocyanate (TDI) by solution casting. Four polyethylene glycols (PEG) of molecular weight 400, 600, 1000, and 4000 were mixed with lignin polyol to incorporate different proportions of soft segment into the network prior to crosslinking. Neither thermal nor mechanical and limited small angle x-ray scattering (SAXS) analysis provided distinct evidence for phase separation and microstructure formation. The study examines the effect of the soft segment in relation to chain length and weight contribution on the thermal and mechanical properties of the final networks. A significant sensitivity of glass transition temperature (T_g), of swelling in DMF, and of the mechanical properties to soft segment content was observed. Some of this sensitivity must, however, be attributed to differences in crosslink density since the polyol to diisocyanate weight ratio was kept constant throughout the synthesis series. The magnitude of the change of the different properties was found to be influenced by both glycol content and glycol molecular weight. The T_g of the network decreased from 105°C to as low as 38°C (HDI), and from 158°C to 70°C (TDI), with incorporation of up to 17.8% glycol, and it was greater with lower molecular weight glycols than with higher ones at any weight fraction. Swelling in DMF increased as expected with soft segment content. Mechanical properties were affected most if HDI and lower molecular weight glycols were used. The uniformity in structure, reduction in brittleness, and considerable improvement in mechanical properties with inclusion of minor PEG contents indicates that lignin-based network polyurethanes can be synthesized with controllable performance characteristics.     

Tailoring the molecular and thermo–mechanical properties of kraft lignin by ultrafiltration

This study has shown that ultrafiltration allows the selective extraction from industrial black liquors of lignin fraction with specific thermo‐mechanical properties, which can be matched to the intended end uses. Ultrafiltration resulted in the efficient fractionation of kraft lignin according to its molecular weight, with an accumulation of sulfur‐containing compounds in the low‐molecular weight fractions. The obtained lignin samples had a varying quantities of functional groups, which correlated with their molecular weight with decreased molecular size, the lignin fractions had a higher amount of phenolic hydroxyl groups and fewer aliphatic hydroxyl groups. Depending on the molecular weight, glass‐transition temperatures (T_g) between 70 and 170°C were obtained for lignin samples isolated from the same batch of black liquor, a tendency confirmed by two independent methods, DSC, and dynamic rheology (DMA). The Fox–Flory equation adequately described the relationship between the number average molecular masses (M_n) and T_g's‐irrespective of the method applied. DMA showed that low‐molecular‐weight lignin exhibits a good flow behavior as well as high‐temperature crosslinking capability. Unfractionated and high molecular weight lignin (M_w >5 kDa), on the other hand, do not soften sufficiently and may require additional modifications for use in thermal processings where melt‐flow is required as the first step. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40799.     

Multiphase materials with lignin. IV. Blends of hydroxypropyl cellulose with lignin

Polymer blends of hydroxypropyl cellulose (HPC) and organosolv lignin (OSL) were prepared by mixing in solutions of both pyridine and dioxane, and casting as films, and by mixing in the melt followed by extrusion. All preparations exhibited partial miscibility as evidenced by a single T_g up to a composition of 40 wt % lignin above which phase separation was detected. Dioxane-cast and injection-molded blends were distinguished from the pyridine-cast materials by a positive T_g deviation from additivity, an approximation which adequately described the latter. This positive deviation in T_g is attributed to the formation of a liquid-crystal mesophase with a resultant reduction of amorphous HPC available for interaction with the lignin component. This explanation is supported by a rapid rise in modulus (～150%) and tensile strength with very low lignin content, and by an associated sharp decline in ultimate elongation. The development of morphological features, as observed by scanning electron microscopy provide further substantiation of this hypothesis.     

Thermal properties of epoxy resins crosslinked by an aminated lignin

Aminated lignin possessing significant amount of reactive amino groups was studied as a curing agent of epoxy resin. Fourier transform infrared spectroscopy results proved the reactivity of the aminated lignin with the epoxy resin. Both appearance features and scanning electron microscopy images indicated that the transparent and homogeneous epoxy resin films could be formed with the aminated lignin less than 40% in the hardener mixture. In addition, thermogravimetric analysis and dynamic thermomechanical analysis results revealed that the epoxy resin cured by aminated lignin had better thermal stability compared with ones cured by a common hardener. The mass loss of the epoxy resin cured by the aminated lignin before 300°C was small around only 2.5%. The T_g (the glass transition temperature) of epoxy resin sample after cured by mixed hardener increased from 79°C to 93°C. The obvious difference (70–84°C) of T_d (the thermal deformation temperature) was also observed from the samples with and without the aminated lignin after cured at a high temperature. POLYM. ENG. SCI., 55:924–932, 2015. © 2014 Society of Plastics Engineers     

Tuning the Properties of Shape-Memory Polyurethanes via the Nature of the Polyester Switching Segment

Shape-memory polymers that contain semicrystalline domains with a melting temperature (T_m) above and a crystallization temperature (T_c) below physiological temperature as fixing elements are useful to create medical devices or implants that can be custom-shaped inside or around the body. With the goal to expand the palette of materials that exhibit such properties, a series of segmented polyurethanes (PUs) containing different crystallizable polyester segments is investigated. The nature of the polyester, its molecular weight, and the ratio of hard to soft segments are systematically varied and the effect on the mechanical, thermal, and shape-memory properties of the various PUs is studied. Poly(1,12-dodecylene dodecanoate), poly(1,6-hexylene dodecanoate), and poly(ethylene sebacate) (PES) are selected as crystallizable polyester segments. The PES-based PUs display T_c values of 25–35 °C and a T_m of 60–63 °C, and allow good shape fixing at 37 °C.     

Ecofriendly modification of acetosolv lignin from oil palm biomass for improvement of PMMA thermo‐oxidative properties

The environmentally friendly esterification of acetosolv lignin (AL), obtained from pressed oil palm mesocarp fibers, is described, for the improvement of thermo‐oxidative properties of poly(methyl methacrylate) (PMMA) films. Acetylation of AL was performed in ecofriendly conditions using acetic anhydride in the absence of catalysts. Acetylated acetosolv lignin (AAL) was successfully obtained in only 12 min with a solvent‐free and catalyst‐free microwave‐assisted procedure. Lignins were characterized by Fourier transform infrared spectroscopy, size exclusion chromatography, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC), confirming the efficacy of the methodology employed. AL and AAL as fillers in different concentrations (1% and 5%) were added to PMMA films. The thermal and mechanical properties of the lignin‐incorporated films were analyzed by TGA, DSC, and dynamic mechanical analysis (DMA). The films incorporated with lignin and acetylated lignin presented initial degradation temperature (T_onset) and onset oxidative temperature (OOT) values higher than pure PMMA films, contributing thus to an enhancement of thermo‐oxidative stability of PMMA. The DMA analyses showed that incorporation of AL or AAL increased the storage modulus (E′) of PMMA films, but did not affect their glass‐transition temperatures (T_g). The results indicate the potential use of oil palm mesocarp lignin to enhance the thermo‐oxidative properties of PMMA without compromising its mechanical response. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45498.     

Mechanical,thermal, and electric properties of polyurethaneimide elastomers

Linear polyurethaneimide elastomers (PUI) were obtained from polyether- or polyester-diols, diphenylmethane diisocyanate or bitolylene diisocyanate and pyromellitic acid dianhydride. It was found that these polymers have considerably better mechanical properties than typical linear polyurethanes (PU). The elastic modulus and stress at break increase with contents of the hard polyimide segments. The softening temperatures and thermal stability of the PUI at 500°C were higher than the ones of PU with similar hard segment contents. Electric properties of PUI were close to the ones of conventional PU. It was shown that cellular PUI had considerably lower dielectric constant. T_g's of the soft segments PUI were less than T_g's corresponding to PU. It is connected with greater phase separation of the hard imide segments from the soft polyether– or polyester–urethane matrix.     

Viscoelastic properties and coating performance of water-soluble acrylic copolymers crosslinked with melamine resin

Acrylic copolymers with different amounts of carboxyl and hydroxyl groups for obtaining practical performance of melamine-cured acrylic coatings was investigated. Property testing results indicated that glass transition temperature (T_g) and shear modulus increased, and molecular weight between crosslinks (M_c) decreased with the increase of hydroxyl and carboxyl number in the acrylic copolymers. The degree of crosslinks influenced the resistance to solvent and chemicals at a lower baking temperature. Compared with acrylic acid, itaconic acid as a carboxyl monomer was more effective in inducing a lower baking schedule. The water-soluble acrylic copolymer, which is neutralized with triethylamine, consists of 20 wt % methylmethacrylate, 55 wt % buthylacrylate, 15 wt % hydroxyethyl methacrylate, and 10 wt % itaconic acid. The copolymer showed higher crosslinks when cured with methoxymethyl melamine formaldehyde resin under a relatively lower baking schedule at 135°C for 30 min. It also has excellent solvent and chemical resistance. This coating film has a T_g value of 39°C, modulus of 2 × 10⁸ dyne/cm² in the rubbery state, and M_c value of 464. Also the acrylic copolymer films with M_c < 900 have good properties for solvent, acid, and alkali resistance. © 1995 John Wiley & Sons, Inc.     

Starch‐g‐polycaprolactone copolymerization using diisocyanate intermediates and thermal characteristics of the copolymers

Starch‐g‐polycaprolactone copolymers were prepared by two‐step reactions. The diisocyanate‐terminated polycaprolactone (NCO–PCL) was prepared by introducing NCO on both hydroxyl ends of PCL using diisocyanates (DI) at a molar ratio between PCL and DI of 2:3. Then, the NCO–PCL was grafted onto corn starch at a weight ratio between starch and NCO–PCL of 2:1. The chemical structure of NCO–PCL and the starch‐g‐PCL copolymers were confirmed by using FTIR and ¹³C‐NMR spectrometers, and then the thermal characteristics of the copolymers were investigated by DSC and TGA. By introducing NCO to PCL (M_n : 1250), the melting temperature (T_m ) was reduced from 58 to 45°C. In addition, by grafting the NCO–PCL (35–38%) prepared with 2,4‐tolylene diisocyanate (TDI) or 4,4‐diphenylmethane diisocyanate (MDI) onto starch, the glass transition temperatures (T_g 's) of the copolymers were both 238°C. With hexamethylene diisocyanate (HDI), however, T_g was found to be 195°C. The initial thermal degradation temperature of the starch‐g‐PCL copolymers were higher than that of unreacted starch (320 versus 290°C) when MDI was used, whereas the copolymers prepared with TDI or HDI underwent little change. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 986–993, 2000     

Structure and Properties Relationships of Epoxy Resins Part 1: Crosslink Density of Cured Resin: (II) Model Networks Properties

Carefully designed resin precursors of high purity, viz. N,N-bis-(2,3-epoxypropyl)-N',N-dimethyl-4,4′-diaminodiphenylenemethane (G2A) and N,N-bis-(2,3-epoxypropyl)-N,N-dimethyl-4,4′-diamino-diphenylenemethane (G2S) were used in combination with N,N,N',N-tetrakis-(2,3-epoxypropyl)-4,4′-diaminodiphenylene methane, TGDDM, and cured with stoichiometric amounts of 4,4′-diamino-diphenylene methane (DDM) to produce networks with a range of controlled crosslink density. The tensile moduli E of the networks in the rubbery state, at T_g+30°C, T_g+45°C and T_g+60°C, were measured using a thermal mechanical analyser. Using the statistical theory of rubber elasticity and the observed values of E, the number average molecular weights between crosslink points M_c for the cured resins were deduced. The experimental M_c values were then compared with those derived by calculations based on a probabilistic model of the network proposed by Chu and Seferis.¹ The experimental M_c values were 2.5 to 5.5 times larger than the calculated ones. The differences were attributable to a consumption of only 40% of the available secondary amino hydrogen via epoxy-amine reaction. A direct relationship was established between the glass transition temperature and the crosslink density 1/M_c for the resins, and the dynamic mechanical properties were studied. The thermal stability of cured resins studied by thermo-gravimetric analysis indicated an enhancement of stability as 1/M_c was reduced. The amount of water absorbed by cured resin was directly proportional to 1/M_c.     

Polyurethanes and polyesters from lignin

Lignin, obtained through steam explosion from straw, was completely characterized via elemental analysis, gel permeation chromatography, ultraviolet and infrared spectroscopy, and ¹³C and ¹H nuclear magnetic resonance spectrometry. Polyurethanes were obtained by treating steam‐exploded lignin from straw with 4,4′‐methylenebis(phenylisocyanate), 4,4′‐methylenebis(phenylisocyanate) –ethandiol, and poly(1,4‐butandiol)tolylene‐2,4‐diisocyanate terminated. The obtained materials were characterized by using gel permeation chromatography, infrared spectroscopy, and scanning electron microscopy. Differential scanning calorimetry analysis showed a T_g at ?6°C, assigned to the glass transition of the poly(1,4‐butandiol) chains. The presence of ethylene glycol reduced the yields of the polyurethanes. The use of the prepolymer gave the best results in polyurethane formation. Steam‐exploded lignin was used as the starting material in the synthesis of polyesters. Lignin was treated with dodecanoyl dichloride. The products were characterized by using gel permeation chromatography, infrared spectroscopy, ¹³C and ¹H nuclear magnetic resonance spectrometry, and scanning electron microscopy. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1451–1456, 2005     

Role of isophorone diisocyanate in the optimization of adhesion tendency of polyurethane pressure sensitive adhesives

The present work describes the role of accurate selection of diisocyanate on the adhesion strength of polyurethanes (PUs). The concentration of diisocyanate induces the hard segment (HS) in the main architecture of PUs which decides the viscoelastic properties of the polymers. A balanced ratio of viscoelastic properties ultimately determines the adhesion strength. The composition of the polymers consists of a blend of macrodiol of hydroxyl-terminated polybutadiene and polypropylene glycol with different molecular weights. Isophorone diisocyanate (IPDI) is used to develop the urethane linkages by maintaining its contribution from 28 to 67% as HS contents. It determines the adhesion strength of the final product. The adhesion strength is evaluated by texture analyzer and 180° peel test. The probe tack analysis shows maximum adhesion energy of 156.2 J cm⁻² and 180° peel test shows 18.80 N/25 mm peel force. The glass-transition (T _g) values obtained through differential scanning calorimetry are in good agreement with theoretically calculated Flory–Fox temperature. The proportion of the loss tangent to the storage modulus (tan δ/E′) shows the optimum value of 2.80 MPa⁻¹. The ideal concentration of IPDI results to achieve better adhesion properties of PU pressure sensitive adhesives. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47124.     

Engineering plastics from lignin II. Characterization of hydroxyalkyl lignin derivatives

Several types of hydroxyalkyl lignin derivatives were synthesized from milled wood, organosolv, steam explosion, acid (H₂SO₄) hydrolysis, and kraft lignin with ethylene oxide, propylene oxide, and butylene oxide by either batch reaction in toluene at 180°C using KOH as catalyst, or in aqueous alkali at room temperature. The isolated derivatives were characterized in terms of their chemical structures by H-NMR and FT-IR spectroscopy. Thermal properties were determined by differential scanning calorimetry. Molecular weights were measured by gel permeation chromatography on polystyrene/lignin model compound calibrated high pressure μ-spherogel columns. Solubilities in various organic solvents spanning a solubility parameter (δ) range from 9.3 to 14.5 and a hydrogen bonding index (γ) range from 1.5 to 18.7 were tested using UV₂₈₀ absorption of solutions of up to with degrees of substitution of between 1 and 2.6 (except for ethylene oxide derivatives which were higher) and with lignin contents of around 60%. The drastic reduction of glass transition temperature of between 50° and 100° is explained with increased free volume of the copolymer and with disruption of hydrogen bonds involving especially phenolic hydroxy groups. The greatly enhanced solubility in organic solvents indicates absence of the gel structure typical of network polymers. No molecular breakdown was observed as a consequence of oxyalkylation. The derivatives had molecular weights (M_w) of between 2000 and 50,000 at dispersity factors of between 2.5 and 25. The derivatives seem to constitute useful prepolymers for thermosetting engineering plastics.     

Thermal and dynamic mechanical properties of hydroxypropyl cellulose films

Differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) were used to characterize the morphology of solvent cast hydroxypropyl cellulose (HPC) films. DSC results were indicative of a semicrystalline material with a melt at 220°C and a glass transition at 19°C (T₁), although an additional event was suggested by a baseline inflection at about 80°C (T₂). Corresponding relaxations were found by DMTA. A secondary relaxation at ?55°C was attributed to the interaction between hydroxyl groups of the polymer and residual diluent. The tan δ peak at T₂ was found to arise from an organized phase, presumably from a liquid-crystal mesophase formed while in solution. Crosslinking with a diisocyanate increased the peak temperature of the two primary relaxations, and resulted in a more clearly defined peak for the T₂ transition. From this behavior it was concluded that both T₁ and T₂ are similar to glass transitions (T_g's) associated with an amorphous component and a more highly ordered phase (due to a residual liquid crystal superstructure) in the HPC bulk.     

Biodegradable polyurethane based on random copolymer of L‐lactide and ϵ‐caprolactone and its shape‐memory property

A series of biodegradable polyurethanes (PUs) are synthesized from the copolymer diols prepared from L ‐lactide and ε‐caprolactone (CL), 2,4‐toluene diisocyanate, and 1,4‐butanediol. Their thermal and mechanical properties are characterized via FTIR, DSC, and tensile tests. Their T_gs are in the range of 28–53°C. They have high modulus, tensile strength, and elongation ratio at break. With increasing CL content, the PU changes from semicrystalline to completely amorphous. Thermal mechanical analysis is used to determine their shape‐memory property. When they are deformed and fixed at proper temperatures, their shape‐recovery is almost complete for a tensile elongation of 150% or a compression of 2‐folds. By changing the content of CL and the hard‐to‐soft ratio, their T_gs and their shape‐recovery temperature can be adjusted. Therefore, they may find wide applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4182–4187, 2007     

Structure-property relationships in thermoplastic elastomers III. Segmented polyacetal-polyurethanes

Dihydroxy-terminated polyacetals had been synthesized from aldehydes and glycols and used as soft segments to obtain segmented polyurethane block copolymers. For soft segment ≥ 1700 M _n, the T_g ranges from–48 to ?58°C and is insensitive to the structures of diisocyanate and chain extender. The T_g of PacPU with 1350 M _n polyacetals is raised to ?38°C, and none was observed for shorter polyacetal chains. The copolymers can be synthesized to have a broad range of mechanical properties, such as modulus from 0.5 to 130 MPa, stress at break from 0.7 to 21 MPa, and elongation at break from 66 to 1300% through the variation of the constituents and composition. The rheologic properties are only slightly dependent on temperature for symmetrical diisocyanates but quite temperature sensitive with asymmetric diisocyanate copolymers. The polyacetals are selected to build in acid-catalyzed thermal decomposition of the thermoplastic elastomers. The extreme acid sensitivity of the polyacetal block is buffered in the coplymers.     

Probing effects of alternately‐embedded phenoxy phenyl lateral groups on properties of novel aromatic poly(ether‐urea)s

A new class of alternate aromatic poly(ether‐urea)s having bulky phenoxy phenyl lateral groups was prepared by the reaction of 2,2′‐bis[(p‐phenoxy phenyl)]‐4,4′‐diaminodiphenyl ether (PPAPE) with two diisocyanates, isophorone diisocyanate and 2,4‐tolylene diisocyanate. The limited viscosity values as well as M _n and M _w values of the resulting polymers were determined. The resulting poly(ether‐urea)s could be easily cast into optically‐transparent, flexible, and light color films. The cut‐off wavelength values and the percentage of transmittance at 800 nm were found to be at about 415 nm and 85%, respectively. PPAPE‐derived poly(ether‐urea)s showed a low‐crystallinity and had excellent solubility in polar organic solvents. T_onset, T_g, T_d5%, and T_d10% values of the PPAPE‐derived polymers measured from their DSC and TGA thermograms were up to 270, 280, 315, and 340°C, respectively. Surface morphology of the resulted poly(ether‐urea)s were also evaluated by their scanning electron microscopy images. Excellent organo‐solubility, satisfactory film quality, moderate T_g values, and good thermal stability make this class of poly (ether‐urea)s promising high‐performance polymeric materials. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Network polyester films from glycerol and dicarboxylic acids

This paper presents information on the preparation of the network polyester films from glycerol (Y_g) and aromatic dicarboxylic acids of phthalic anhydride (P), dimethyl isophthalate (I) and dimethyl terephthalate (T), as well as aliphatic dicarboxylic acids of adipic, sebacic, 1, 10-decanedicarboxylic and 1, 12-dodecanedicarboxylic acids, and their properties. Y_g and dicarboxylic acid were polycondensed immediately before the gelation started. The prepolymers obtained were cast from DMF solution and successively post-polymerized at various temperatures and times to form networks. The resultant films were transparent, flexible and insoluble in organic solvents. Heat distortion temperature (T_h) measured by a penetration mode of thermomechanical analysis increased with increasing post-polymerization temperature and time, and then leveled out. T_h values corresponded well to the glass transition temperature (T_g) measured by differential thermal analysis (DTA). T_h was 152°C, 162°C and 197°C for Y_gP, Y_gI and Y_g T post-polymerized at 270°C for 6 h, respectively. T_h values of network films made from aliphatic dicarboxylic acids could not be observed until complete probe penetration occurs, as a result of thermal decomposition because the T_g is lower than room temperature. The degree of reaction estimated from the IR absorbance of hydroxyl and methylene groups was in the range of 60–80%. Two diffraction peaks appeared in the wide-angle X-ray scattering pattern, suggesting some ordered structure owing to the regular networks. Density decreased with increasing post-polymerization time and temperature, in the order Y_gP > Y_gI > Y_gT. Network films made from aliphatic dicarboxylic acids had much lower tensile strength and Young's modulus, and greater elongation, than those made from dicarboxylic acids, as a result of the T_g being below room temperature.