Microstructural development during crystallization firing of a dental-grade nanostructured lithia-zirconia glass-ceramic

The microstructural development during crystallization firing of a commercially-available dental-grade nanostructured lithia-zirconia glass-ceramic (Vita Suprinity® PC) was unraveled using a wide battery of ex-situ and in-situ characterization techniques. It was found that the milling blocks are slightly crystallized glass-ceramics, with a complex chemical composition and consisting of partially de-polymerized glass plus lithium silicate (Li₂SiO₃) nanocrystals. It was also found that during crystallization firing the glassy matrix first reacts with part of the Li₂SiO₃ to form lithium disilicate (Li₂Si₂O₅) at ～810?820 °C, and then lithium orthophosphate (Li₃PO₄) precipitates from the glass. This results in glass-ceramics with abundant nanocrystals embedded in a sparse zirconosilicate glass matrix (containing many other cations subsumed) that, due to its high viscosity, inhibited crystal growth. Therefore, these dental glass-ceramics are not reinforced with zirconia (ZrO₂) crystals unless over-fired above ～890 °C and at the expense of its singular nanostructure. Finally, this study opens doors for optimizing the clinical performance of these dental glass-ceramics via microstructural tailoring.     

Effect of microstructural evolution on the mechanical properties of lepidolite based glass-ceramics

In this paper, effect of microstructural evolution on mechanical property of lepidolite based glass-ceramics of MgO–Al₂O₃–SiO₂–Li₂O–R₂O–F(R=Na, K) system during the crystallization process has been studied. The results show that two distinct regions of strength dependence on grain size are found. The critical values of the flake diameter and aspect ratio of lepidolite are 1.8 and 4.6μm, respectively. The crystallization temperature (T_C) of critical point locates at 1060 °C. When T_C⩽1060 °C, the bending strength increases with heat-treatment temperature ascribing to the randomly oriented and interlocked lepidolite crystallites, which cause crack divert or blunt to limit the further development of the flaw size and increase the surface energy of fracture. While T_C> 1060 °C, the increased boundary shear stress arising from the mismatch of thermal coefficient between the lepidolite crystallite and the residual glass phase results in the decrease of strength.     

Processing of transparent glass-ceramics by nanocrystallisation of LaF3

Transparent glass-ceramics have been prepared by heat-treating oxyfluoride glasses in the Na₂O–Al₂O₃–SiO₂–LaF₃ system. The nanocrystallisation of LaF₃ was achieved by controlling time and temperature parameters. Glasses and glass-ceramics were characterised by dilatometry, DTA, XRD and TEM. The mean crystal size (<20 nm) and the crystal fraction increase with the temperature of heat treatment, while they reach a maximum at about 20 h at a temperature close to T_g. The crystallisation of phases containing glass modifier elements as well as F anions leads to the increase in the viscosity of the remaining glass matrix. Phase separation occurs in glass-ceramics depending on the glass composition which affects nanocrystallisation.     

Effect of metastable phase on the crystallization and mechanical properties of MgO-Al2O3-SiO2 glass-ceramics without nucleating agents

Glass-ceramics without nucleating agents usually undergo surface crystallization, which deteriorates the overall performance of the products. In this paper, we evaluated the effects of the metastable MgAl₂Si₃O₁₀ crystalline phase on the crystallization behavior of a MgO–Al₂O₃–SiO₂ (MAS) glass without nucleating agents and mechanical properties of the glass-ceramics obtained. The results demonstrated that the precipitation of metastable MgAl₂Si₃O₁₀ crystallites promotes the crystallization mechanism transformed from surface crystallization into volume crystallization with two-dimensional crystal growth. Furthermore, the grain size of MgAl₂Si₃O₁₀ near the surface of the prepared glass-ceramics was larger than that of MgAl₂Si₃O₁₀ inside, which helps to generate compressive stress and improves its mechanical properties. The glass-ceramics containing metastable MgAl₂Si₃O₁₀ phase exhibited an enhanced hardness in the range of 7.6 GPa–9.5 GPa for indentation loads ranging from 2.94 N to 98 N, and indentation size effect behavior was observed in Vickers hardness tests of both MAS glass and glass-ceramics. The load-independent hardness values for MAS glass and glass-ceramics were reliably evaluated by the modified proportional specimen resistance (MPSR) model of 7.1 GPa and 7.6 GPa, respectively, with a high correlation coefficient of more than 0.9999. This work reveals the unexploited potential of the metastable phase in improving the crystallization ability and mechanical properties of glass-ceramics.     

Glass forming,crystallization, and physical properties of MgO-Al2O3-SiO2-B2O3 glass-ceramics modified by ZnO replacing MgO

This study focused on the glass forming, crystallization, and physical properties of ZnO doped MgO-Al₂O₃-SiO₂-B₂O₃ glass-ceramics. The results show that the glass forming ability enhances first with ZnO increasing from 0 to 0.5 mol%, and then weakens with further addition of ZnO which acted as network modifier. No nucleating agent was used and the crystallization of studied glasses is controlled by a surface crystallization mechanism. The predominant phase in glass-ceramics changed from α-cordierite to spinel/gahnite as ZnO gradually replaced MgO. The phase type did not change; however, the crystallinity and grain size in glass-ceramics increased when the glasses were treated from 1030 °C to 1100 °C. The introduction of ZnO can improve the thermal, mechanical, and dielectric properties of the glass-ceramics. The results reveal a rational mechanism of glass formation, crystal precipitation, and evolution between structure and performance in the xZnO-(20-x)MgO-20Al₂O₃-57SiO₂-3B₂O₃ (0 ≤ x ≤ 20 mol%) system.     

Crystallization behavior and mechanical properties of high strength mica-containing glass-ceramics from granite wastes

The high-strength mica-containing glass-ceramics were prepared from granite wastes by bulk crystallization. The influences of SiO₂/Al₂O₃ molar ratio (S/A = 7.72, 9.62, 12.58, 17.82 and 29.67) on the crystallization behavior, microstructure, mechanical properties and machinability of glass-ceramics were investigated. The results demonstrated that the polymerization degree of the glass network decreased with the S/A ratio increasing, which further caused the decrease in glass transition temperature and crystallization temperatures. The increase in the S/A ratio promoted the precipitation of diopside, hectorite, kalsilite and tainiolite in glass-ceramics when the samples were heated at 750 °C, while inhibiting the precipitation of forsterite. For the glass-ceramics crystallized at 800 and 900 °C, the main crystalline phases transformed from diopside, forsterite, and nepheline to diopside, kalsilite, and tainiolite, with the S/A ratio increasing. As the SiO₂ gradually replaced Al₂O₃, the morphology of crystals changed from lamellar to granular, while the mean size of crystals reduced. The Vickers-Hardness values of glass-ceramics crystallized at 800 and 900 °C ascended with S/A ratio rising, and the values were above 6.30 GPa. The bending strength of most glass-ceramics is stable between 90 and 140 MPa, among which the maximum bending strength is 133.28 ± 14.81 MPa. The fracture toughness of the glass-ceramic crystallized at 800 and 900 °C declined, while that at 700 °C increased with a larger S/A ratio. Glass-ceramics after heat-treated at 900 °C with S/A ratio of 9.62 had the largest fracture toughness of 3.28 ± 0.15 MPa m^1/2. In preliminary tests of machinability, glass-ceramic after heat-treated at 900 °C with S/A ratio of 9.62 showed better results.     

High-strength,translucent glass-ceramics in the system MgO-ZnO-Al2O3-SiO2-ZrO2

In a MgO/Al₂O₃/SiO₂/ZrO₂ glass-ceramic MgO was substituted by equimolar ZnO concentrations. The effect of this substitution on the crystallization behavior, the microstructure and the mechanical properties of the glass-ceramics was studied. The crystal phases and the microstructure were analysed by X-ray diffraction and scanning electron microscopy. Tetragonal ZrO₂, a high-/low-quartz solid solution (high-/low-QSS) and spinel/gahnite were observed in the entire bulk of the glass-ceramics. Additionally, indialite or cristobalite are detected at the surface of some glass-ceramics. The substitution of small ZnO concentrations induces an increasing low-QSS concentration and hence higher microhardness and Young’s modulus. By contrast, higher ZnO concentrations lead to a liquid/liquid phase separation in the glass. Moreover, spinel/gahnite is the main crystal phase and the concentration of the low-QSS is smaller in theses glass-ceramics which also do not show as good mechanical properties. However, the biaxial flexural strength of the glass-ceramics is not notably affected by the ZnO concentration.     

Orientated crystallization of fresnoite glass-ceramics by using a thermal gradient

The glass with chemical composition (mol%) 33.33 BaO, 16.66 TiO₂, 50.00 SiO₂ was prepared by a conventional melt-quenching method. The glass-ceramics with a Ba₂TiSi₂O₈ crystal was prepared by crystallization of the glasses using a hot stage. The crystals are shown highly orientated along the c-axis perpendicular to the hot surface of the sample. Crystallization was controlled by a diffusion process with surface nucleation. The activation energy for crystallization was about 518 kJ/mol. The mechanism of oriented crystallization was considered in the present paper.     

Tuning energy storage and light transmittance properties in ZrO2-modified Na2O–K2O–Nb2O5–SiO2 glass-ceramics

Crystallization kinetics in ZrO₂-modified glass-ceramics, (35-x)Na₂O–5K₂O–40Nb₂O₅–20SiO₂-xZrO₂ (x = 0, 1, 3, 5, 10 mol%), is analyzed by crystallization activation energy E_c and kinetic parameter k. A large kinetic parameter k of 1.657 × 10²⁵ is found for the sample with x = 1, which indicates a high tendency toward crystallization. NaNbO₃ is formed as the major phase, and its crystallinity changes significantly by the addition of ZrO₂. It is found that the dielectric permittivity and maximum polarization are affected by crystallinity. Large domains are formed, and a relaxation process appears at high frequencies. In addition, the breakdown strength (BDS) is affected by the strong electric field distortion rather than the resistance in this system. Complex impedance analysis shows that resistance decreases with the addition of ZrO₂. The electric field distortion of the glass-ceramics is simulated by COMSOL. A low interfacial polarization activation energy E_a of 0.821 eV is achieved by the addition of ZrO₂. The maximum pulse power density reaches 90 MW/cc at 350 kV/cm for the sample with x = 10, and the pulse energy density attains 0.91 J/cm³ at 300 kV/cm for the sample with x = 1. Light transmittance is achieved because of the low crystallinity and the disappearance of cristobalite SiO₂ in the Na₂O–K₂O–Nb₂O₅–SiO₂ glass-ceramics.     

Influence of nucleating agents on crystallization and electrical properties of SiO2–MgO–MgF2–K2O mica glass-ceramics

The effects of adding ZrO₂ and TiO₂ at the expense of MgF₂ on the crystallization, microstructure, mechanical properties, thermal properties and electrical properties of mica glass-ceramics based on the SiO₂–MgO–MgF₂–K₂O system were investigated by the differential scanning calorimetry (DSC), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), microhardness tester and resistivity tester. The electrical properties were discussed emphatically. The results showed that the additions of ZrO₂ and/or TiO₂ at the expense of MgF₂ effectively increase the viscosity, the glass transition temperatures (T_g) and the crystallization temperatures (T_p) of the glasses. The crystallization activation energy (E_c) of the amorphous glasses varied with the nucleating agents was discussed in depth. It was discovered that the nucleating agents had no effect on the crystal phase type but had a certain effect on the crystallinity and microstructure. Tetrasilicic fluoromica and enstatite were precipitated at different crystallization temperatures. Due to the non-stoichiometric ratio of tetrasilicic fluoromica crystal, the prepared glass-ceramics had high dielectric constant (24.4–34.3) and volume resistivity (>2 × 10¹¹ Ω cm) at 25 ^°C, and the dielectric loss was almost zero.     

Rapid preparation of low thermal expansion transparent LAS nanocrystalline glass by one-step thermoelectric treatment

The Li₂O–Al₂O₃–SiO₂ (LAS) glass ceramics are prepared by one-step thermoelectric treatment. The influence of thermoelectric treatments on LAS glass-ceramics were studied. The crystal phase composition and microstructure of the LAS glass-ceramics were investigated by DSC, SEM, XRD and FTIR. Moreover, the thermal expansion performance and light transmittance of LAS nanocrystalline glass were characterized. The results show that low-expansion transparent LAS nanocrystalline glass can be produced in a short time by thermoelectric treatment. The free energy of nucleation and the degree of polymerization of the glass network are reduced by the electric field. The key is that the electric field polarizes Ti and Zr ions at the crystallization temperature, so that the crystal nuclei repel the same poles. This allows uniform crystal distribution, promotes crystallization and reduces one-step crystallization of crystal agglomeration. This proves that the rapid preparation of nanocrystalline glass by the one-step method is feasible, and provides a reference for the future one-step processing of glass-ceramics.     

Effect of ZnO on the crystallization behavior and properties of SiO2–CaO–Al2O3–Fe2O3 glass-ceramics prepared from simulated secondary slag after reduction of copper slag

The feasibility of preparing low-cost glass-ceramics from Zn-containing dust and secondary molten slag generated during the carbothermal reduction of copper slag was investigated. Analytical-grade agents, such as ZnO, Fe₂O₃, SiO₂, CaO, and Al₂O₃, were used to simulate the dust and secondary slag. The effect of ZnO content on the crystallization behavior, structure, and mechanical properties of the glass-ceramics was investigated through X-ray diffraction analysis, scanning electron microscopy-energy dispersive spectrometry, differential scanning calorimetry, Fourier transform infrared spectroscopy, and Raman spectroscopy. The results showed that with increased ZnO content from 0 to 6 wt%, the crystallization activation energy of base glass increased from 386.05 to 425.89 kJ/mol. Meanwhile, the average value of the crystal growth index increased from 1.91 to 4.10, and the highest crystallization rate of the glass-ceramics increased from about 1.44 to 23.11 mm³/min. The increased ZnO in glass-ceramics promoted the precipitation of gehlenite, but inhibit the crystallization of anorthite. When the ZnO content was 6 wt%, the comprehensive properties of the glass-ceramics were better; the flexural strength, microhardness, volume density, water absorption rate, and open porosity were 58.67 MPa, 738.35 HV, 2.92 g/cm³, 0.44% and 1.27%, respectively.     

Bioactivity and antibacterial activity against E-coli of calcium-phosphate-based glasses: Effect of silver content and crystallinity

In this work we developed improved bioactive glasses and glass-ceramics for biomedical applications, investigating their in vitro bioactivity, biocompatibility and antibacterial properties against E-Coli. A melt-quenched bioactive glass of the SiO₂-CaO-P₂O₅-MgO system was modified with the addition of 1 and 2 mol% Ag₂O and the 1 mol% Ag₂O-containing glasses were then heat treated to produce glass-ceramics. Surface modifications after soaking in SBF and ionic concentration changes showed that addition of silver and crystallization did not affect bioactivity although crystalline phases promoted a decrease in the degradation rate.Biocompatibility of all Ag-containing glasses and glass-ceramics was confirmed for certain samples concentrations. The antibacterial activity of the glasses against E-Coli was generally improved with decreasing particle size or increasing Ag₂O. The Ag-containing glass-ceramics with higher content of crystalline phase appears as a promising biocompatible biocidal material with potential applications in bone-related diseases.     

Effect of MgO/Al2O3 ratio on the crystallization behaviour of Li2O–MgO–Al2O3–SiO2 glass-ceramic and its wettability on Si3N4 ceramic

The composition governs the crystallization ability, the type and content of crystal phases of glass-ceramics. Glass-ceramic joining materials have generated more research interest in recent years. Here, we prepared a novel Li₂O–MgO–Al₂O₃–SiO₂ glass-ceramic for the application of joining Si₃N₄ ceramics. We investigated the influence of the MgO/Al₂O₃ composition ratio on microstructure and crystallization behaviour. The crystallization kinetics demonstrated that the glasses had excellent crystallization ability and high crystallinity. β-LiAlSi₂O₆ and Mg₂SiO₄ were precipitated from the glass-ceramics, and the increase of MgO concentration was conducive to the precipitation of Mg₂SiO₄. Among the glass-ceramic samples, the thermal expansion coefficient of LMAS2 glass-ceramic was 3.1 × 10^?6/°C, which was very close to that of Si₃N₄ ceramics. The wetting test showed that the final contact angle of the glass droplet on the Si₃N₄ ceramic surface was 32° and the interface was well bonded.     

Crystallization and Luminescence Properties of Sm<Superscript>3+</Superscript>-Doped SrO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> Glass-Ceramics

Sm³⁺-doped SrO–Al₂O₃–SiO₂ glass-ceramics with excellent luminescence properties were prepared by batch melting and heat treatment. The crystallization behavior and luminescent properties of the glass-ceramics were investigated. The results indicate that the crystal phase in this system is monocelsian (SrAl₂Si₂O₈). Under the excitation with blue light (475 nm) the Sm³⁺-doped SrO–Al₂O₃–SiO₂ glass-ceramics emit green, orange and red lights centered at 565, 605, 650 and 715 nm, which can be assigned to the ⁴G_5/2 → ⁶H_J/2 (J = 5, 7, 9, 11) electron transitions in Sm³⁺ ions, respectively. With the increase of nucleation/crystallization temperature, the crystallite part rises from 66 to 79%. Besides, by increasing crystallization temperature or concentration of Sm³⁺, the samples emission located at 565, 605 and 650 nm is intensified significantly. We envision that, by fine controlling and combining of these three (green, orange and red) lights in an appropriate proportion, the Sm³⁺-doped glass-ceramics are promising luminescence materials for white light-emitting diodes devices.     

Kinetics and in situ observation of nonisothermal crystallization in Bayan Obo tailing-based nanocrystalline glass-ceramic

In recent years, the preparation of CMAS nanocrystalline glass-ceramics has shown potential as an application of secondary resourcing technology in utilizing Bayan Obo iron ore tailings containing rare earth elements. The crystallization mechanism for nanodiopside-type glass-ceramics was studied via an investigation of the nonisothermal crystallization kinetics of the glass system, combined with the in situ observation of softening and crystallization of the basic glass using a high-temperature laser confocal microscope. The results show that the activation energy of nucleation in the glass system is higher than that of crystal growth by using the Ozawa model. The crystallization mechanism changes as the crystallization fraction increases, that is, from the three-dimensional growth in which the nucleation rate increases with time in an interface-controlled manner (a > 1, b = 1, m = 3) at the initial stage of crystallization to a decreased nucleation rate in a diffusion-controlled growth (a = 0.5, b = 0.5, m = 3) at the middle and later stages. This process involves both surface crystallization and volume crystallization. The crystallization was observed in situ, and it was further confirmed that there exists a critical nucleation temperature between T_g and T_x, which is related to the interface free energy and critical Gibbs free energy difference. When the temperature exceeds the critical value of T_g + 55 K, the system begins to exhibit visible crystallization. With an increase in temperature, the basic glass softened considerably, while the crystal grew significantly. In addition, the surface roughness can be used to characterize the crystallization process, providing a new research method for crystal growth.     

Preparation and characterization of alkali-free glass substrates with enhanced properties for TFT–LCDs applications

To obtain an alkali-free glass substrate with enhanced properties for thin-film transistor–liquid crystal displays (TFT–LCDs) applications, we chose a base glass composed of 3B₂O₃-15Al₂O₃-58SiO₂-22MgO-0.5SrO-1.5MgF₂ (mol%) for nucleation–crystallization. The results show that when the nucleation–crystallization processes of the base glass are 810 °C/6 h + 880 °C/6–9 h, the prepared GC/6–GC/9 glass-ceramics exhibit enhanced properties because of the precipitation of nano-sized cordierite. The transmittances in the visible range of the GC/6–GC/9 glass-ceramics exceed 85%, the densities are 2.564–2.567 g/cm³, thermal expansion coefficients are 2.934–3.059 × 10^-6/°C (25–300 °C), compressive strengths are 417–589 MPa, bending strengths are 141–259 MPa, Vickers hardnesses are 6.8–7.8 GPa, and strain points are approximately 735 °C. Considering these properties, the prepared GC/6–GC/9 glass-ceramics have good potential as candidate materials for alkali-free glass substrates. Additionally, these results demonstrate that it is feasible to improve the properties of alkali-free glass substrates by nucleation–crystallization.     

Effect of TiO2 on crystallization and mechanical properties of MgO–Al2O3–SiO2 glasses containing P2O5

MgO–Al₂O₃–SiO₂ glass-ceramics have been widely used in military, industrial, and construction applications. The nucleating agent is one of the most important factors in the production of glass-ceramics as it can control the crystallization temperature or the grain size. In this study, we investigated the effect of replacing P₂O₅ with different amounts of TiO₂ on the crystallization, structure, and mechanical properties of an MgO–Al₂O₃–SiO₂ system. The crystallization and microstructure were investigated by differential scanning calorimetry, Raman spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The mechanical properties were investigated by measuring the Vickers hardness, Young's modulus, and fracture toughness. The results showed that adding TiO₂ favored the precipitation of fine grains and significantly increased the Vickers hardness, Young's modulus, and fracture toughness of the glasses. Introducing an appropriate amount of TiO₂ can make a glass structure more compact, promote crystallization, and improve the mechanical properties of MgO–Al₂O₃–SiO₂ glass-ceramics.     

Potential utilization of oil sludge incineration bottom ash for glass-ceramics: Crystallization kinetics,properties and toxicological evaluation

The bottom ash (OIBA) generated from the incineration of hazardous oil sludge is classified as a hazardous waste. In this work, the OIBA was applied as raw material to prepare SiO₂-Al₂O₃-CaO system glass-ceramics by melt-sintering with the addition of waste glass wool (GW). The effects of basicity (CaO/SiO₂ ratio, 0.52-1.05) and sintering temperature (900–1050 °C) on the crystallization kinetics, properties, microstructure, leaching concentrations of heavy metals and potential toxicity of glass-ceramics were investigated. The results showed that the crystallization pattern was two-dimensional crystallization, and with the decrease of basicity, the main crystalline phase evolved from gehlenite to diopside. And the glass-ceramics with basicity of 0.88 and sintering temperature of 950 °C exhibited the best comprehensive properties, including density (2.72 g/cm³), water absorption (0.06%), compressive strength (452.45 MPa) and chemical corrosion resistance. In addition, the reduction of heavy metal leaching concentration indicates that produced glass-ceramics showed excellent solidification effect on heavy metals, the low toxicity of glass-ceramics leaching solution to the wheat seeds and Artemia suggests the environmental protection characteristics of OIBA-based glass-ceramics. These findings proved that the glass-ceramics produced by OIBA and GW could be a promising method to dispose hazardous waste with preparing high value-added construction materials.     

Crystallization behavior and properties of K2O–CaO–Al2O3–SiO2 glass-ceramics

In order to obtain high-strength anorthite glass-ceramics, K₂O–CaO–Al₂O₃–SiO₂ quaternary glass and relevant glass-ceramics were prepared and investigated. The results show that anorthite along with kalsilite or leucite was precipitated from the parent glass. Kalsilite crystals were formed firstly and then converted into leucite through reacting with SiO₂ in the glass phase. The morphology of the crystals was dependent on the heat-treatment temperature. Column crystals were transformed into fine granular grains when the sintering temperature changed from 900 °C to 1100 °C. The activation energy (E_α) and avrami constant (n) were also calculated as 463.81 KJ/mol and 3.74 respectively, indicating that bulk nucleation and three-dimensional crystal growth were the dominating mechanisms in the temperature range 1000–1100 °C. The maximum value of the flexural strength for the glass-ceramics containing leucite was 248 MPa and the coefficient of thermal expansion (CTE) was in the range 5.69~11.94×10⁻⁶ K⁻¹. The leucite is the main reason for the high CTEs and high flexural strength of glass-ceramics.