The influence of different SiC amounts on the microstructure,densification, and mechanical properties of hot-pressed Al2O3-SiC composites

The hot pressing process of monolithic Al₂O₃ and Al₂O₃-SiC composites with 0-25 wt% of submicrometer silicon carbide was done in this paper. The presence of SiC particles prohibited the grain growth of the Al₂O₃ matrix during sintering at the temperatures of 1450°C and 1550°C for 1 h and under the pressure of 30 MPa in vacuum. The effect of SiC reinforcement on the mechanical properties of composite specimens like fracture toughness, flexural strength, and hardness was discussed. The results showed that the maximum values of fracture toughness (5.9 ± 0.5 MPa.m^1/2) and hardness (20.8 ± 0.4 GPa) were obtained for the Al₂O₃-5 wt% SiC composite specimens. The significant improvement in fracture toughness of composite specimens in comparison with the monolithic alumina (3.1 ± 0.4 MPa.m^1/2) could be attributed to crack deflection as one of the toughening mechanisms with regard to the presence of SiC particles. In addition, the flexural strength was improved by increasing SiC value up to 25 wt% and reached 395 ± 1.4 MPa. The scanning electron microscopy (SEM) observations verified that the increasing of flexural strength was related to the fine-grained microstructure.     

Mechanical properties of borothermally synthesized zirconium diboride at elevated temperatures

The mechanical properties of a nominally phase pure ZrB₂ ceramic were measured up to 2300°C in an argon atmosphere. ZrB₂ was hot pressed at 2000°C utilizing borothermally synthesized powder from high purity ZrO₂ and B raw materials. The relative density of the ceramics was about 95% with an average ZrB₂ grain size of 8.8 µm. The room temperature flexural strength was 447 MPa, with strength decreasing to 196 MPa at 1800°C, and then increasing to 360 MPa at 2300°C. The strength up to 1800°C was likely controlled by a combination of effects: surface damage from oxidation of the specimens, stress relaxation, and decreases in the elastic modulus. The strength above 1800°C was controlled by flaws in the range consistent with sizes of the maximum ZrB₂ grain size and the largest pores. Fracture toughness was 2.3 MPa·m^1/2 at room temperature, increasing to 3.1 MPa·m^1/2 at 2200°C. The use of higher purity starting materials improved the mechanical behavior in the ultra-high temperature regime compared to previous studies.     

Effects of ZrB2 reinforcement on microstructure and mechanical properties of a spark plasma sintered mullite-CNT composite

A high density 10 wt% ZrB₂ and 1 wt%. CNT-reinforced mullite-based composite was prepared by spark plasma sintering (SPS) at temperature of 1350 °C, average heating rate of 60 °C/min and a soaking time of 5 min. Under these conditions, the sintered composite obtained a high hardness (16.24 ± 0.12 GPa), fracture toughness (4.18 ± 0.51 MPa m^1/2) and flexural strength (488 ± 21 MPa). The results of FESEM images showed a uniform distribution of the reinforcement particles in the composite. The resulting CNTs survived the sintering process and did not undergo any transformation. A transgranular fracture was predominantly observed in the fractured surface micrographs of the composite. The CNTs pullout and crack-bridging toughening mechanisms were also observed in the composite, which could have a significant contribution to the fracture energy and the interfacial adhesion.     

Mechanical,tribological and electrical properties of ZrB2 reinforced Cu processed via milling and high-pressure hot pressing

The present work investigates the effect of (0–10 wt%) ZrB₂ reinforcement on densification, mechanical, tribological and electrical properties of Cu. The consolidation of Cu–ZrB₂ samples was carried out using a hot press (temperature: 500 °C, pressure: 500 MPa, time: 30 min, vacuum pressure: 1.3 × 10^-2 mbar). The bulk density of the hot-pressed Cu composites decreased from 8.84 g/cc to 8.16 g/cc and the relative density of samples lowered from 98.6% to 92.1% with the addition of ZrB₂. The incorporation of hard ZrB₂ (up to 10 wt%) improved the hardness of Cu (1.32–2.55 GPa). However, the yield strength and compressive strength of Cu composites increased up to 5 wt% ZrB₂, and further addition of ZrB₂ lowered its strength. The yield strength of Cu samples varied from 602 to 672 MPa and the compressive strength between ~834 and 971 MPa. On the other hand, the coefficient of friction (COF) (from 0.49 to 0.18) and wear rate (from 49.3 × 10^-3 mm³/Nm to 9.1 × 10^-3 mm³/Nm) of Cu–ZrB₂ samples considerably decreased with the addition of ZrB₂. Significantly low wear was observed with Cu-10 wt% ZrB₂ (Cu-10Z) samples, which is 5.41 times less than pure Cu. As far as the wear mechanisms are concerned, in pure Cu, continuous chips (wear debris) were formed during sliding wear by plowing. Whereas the major amount of material loss was occurred due to the plowing mechanism with discontinuous and short chip formation for Cu–ZrB₂ composites. The electrical conductivity of Cu–ZrB₂ samples decreased from 75.7% IACS to 44.1% IACS. In particular, Cu with ZrB₂ (up to 3 wt%) could retain the conductivity of 66.8% IACS. This study reveals that the addition of ZrB₂ (up to 3 wt%) is advantageous to have a good combination of properties for Cu.     

Mechanical,Tribological, and Thermal Properties of Hot‐Pressed ZrB2‐B4C Composite

The effect of addition of submicrometer‐sized B₄C (5,10 and 15 wt%) on microstructure, phase composition, hardness, fracture toughness, scratch resistance, wear resistance, and thermal behavior of hot‐pressed ZrB₂‐B₄C composites is reported. ZrB₂‐B₄C (10 wt%) composite has V_H1 of 20.81 GPa and fracture toughness of 3.93 at 1 kgf, scratch resistance coefficient of 0.40, wear resistance coefficient of 0.01, and ware rate of 0.49 × 10^?3 mm³/Nm at 10N. Crack deflection by homogeneously dispersed submicrometer‐sized B₄C in ZrB₂ matrix can improve the mechanical and tribological properties. Thermal conductivity of ZrB₂‐B₄C composites varied from 70.13 to 45.30 W/m K between 100°C and 1000°C which is encouraging for making ultra‐high temperature ceramics (UHTC) component.     

Preparation and properties of dense ZrB2 composite reinforced by elongated SiC and Al3BC3 grains

Dense ZrB₂-SiC-Al₃BC₃ ultra-high temperature ceramic composite was fabricated by hot pressing sintering at 1900°C for 1 hour under a pressure of 20 MPa using Zirconium diboride (ZrB₂) as the raw material and a powder mixture of SiC, B₄C, Al, and carbon as the sintering additive. Al and B₄C underwent in situ reaction with carbon powder to produce Al₃BC₃, which promoted the densification of ZrB₂ ceramic. SiC grains were found to be elongated during sintering. The ZrB₂-SiC-Al₃BC₃ composite exhibited excellent mechanical properties, such as high flexural strength of 589 ± 147 MPa and fracture toughness of 7.81 ± 1.09 MPa m^1/2. Oxidation behavior of the ZrB₂-SiC-Al₃BC₃ composite was studied in air at 1500°C for 1 hour. A continuous layer of oxides consisting of a mixture of SiO₂, Al₂SiO₅, and Al₂O₃ was formed on the surface of the ZrB₂-SiC-Al₃BC₃ composite. This layer of oxides efficiently prevented oxygen from diffusing into the specimens during oxidation, which improved the oxidation resistance of the ZrB₂ ceramics.     

Advantages and disadvantages of graphite addition on the characteristics of hot-pressed ZrB2–SiC composites

ZrB₂–SiC–graphite composites with 0–35 vol% graphite flakes were densified via hot-pressing route at the temperature of 1800 °C under the uniaxial pressure of 40 MPa for 1 h. Consolidation, mechanical properties, and microstructure of hot-pressed composites were investigated by variation of graphite content. By the addition of graphite, the relative density of composites increased, and at this hot pressing condition, fully densified composites were fabricated. The highest flexural strength of 366 MPa was measured for composite containing 7.5 vol% graphite, while the maximum Vickers hardness resulted in 2.5 vol% graphite doped one, and its value was equal to 20.8 GPa. Phase analysis of hot-pressed samples revealed the formation of the Zr₃C₂ and B₄C phases besides the main existing ZrB₂, SiC, and graphite phases. The newly carbide phases formed at the surface of ZrB₂ grains. The addition of graphite into the ZrB₂–SiC composites improved the sintering process and caused a fine-grained microstructure.     

Densification,mechanical, and tribological properties of ZrB2-ZrCx composites produced by reactive hot pressing

ZrB₂-ZrC_x composites were produced using Zr:B₄C powder mixtures in the molar ratios of 3:1, 3.5:1, 4:1, and 5:1 by reactive hot pressing (RHP) at 4-7 MPa, 1200°C for 60 minutes. X-ray diffraction analyses confirmed the formation of nonstoichiometric zirconium carbide (ZrC_x) with different lattice parameters and enhanced carbide formation by increasing the Zr mole fraction. An increase in applied pressure from 4 to 7 MPa was responsible for the improved relative density (RD) of 4Zr:B₄C composition from 86% to 99%. Microstructural studies on Zr-rich composites showed a reduction in unreacted B₄C particles and enriched elongated ZrB₂ platelets. Reaction and densification mechanism in 4Zr:B₄C composition were studied as a function of temperature increased from 600 to 1200°C at an applied constant pressure of 7 MPa. After 1000°C, <40 vol.% of unreacted Zr was observed during the densification process. Concurrently, low energies of carbon diffusion and carbon vacancy formation were found to enhance nonstoichiometric ZrC_x formation, which was found to be responsible for the completion of the reaction. The plastic deformation of unreacted Zr was responsible for the densification of the ZrB₂-ZrC_x composite. The results clearly showed that the applied pressure is five times lower than the reported values. Moreover, a temperature of 1200°C was sufficient to produce dense ZrB₂-ZrC_x composites. The improved microhardness, flexural strength, fracture toughness, and specific wear rate were 8.2-15 GPa, 265-590 MPa, 2.82-6.33 MPa.m^1/2, and 1.43-0.376 × 10⁻² mm²/N, respectively.     

Fabrication and properties of ZrB2–SiC–BN machinable ceramics

ZrB₂–SiC–BN ceramics were fabricated by hot-pressing under argon at 1800 °C and 23 MPa pressure. The microstructure, mechanical and oxidation resistance properties of the composite were investigated. The flexural strength and fracture toughness of ZrB₂–SiC–BN (40 vol%ZrB₂–25 vol%SiC–35 vol%BN) composite were 378 MPa and 4.1 MPa m^1/2, respectively. The former increased by 34% and the latter decreased by 15% compared to those of the conventional ZrB₂–SiC (80 vol%ZrB₂–20 vol%SiC). Noticeably, the hardness decreased tremendously by about 67% and the machinability improved noticeably compared to the relative property of the ZrB₂–SiC ceramic. The anisothermal and isothermal oxidation behaviors of ZrB₂–SiC–BN composites from 1100 to 1500 °C in air atmosphere showed that the weight gain of the 80 vol%ZrB₂–20 vol%SiC and 43.1 vol%ZrB₂–26.9 vol%SiC–30 vol%BN composites after oxidation at 1500 °C for 5 h were 0.0714 and 0.0268 g/cm², respectively, which indicates that the addition of the BN enhances oxidation resistance of ZrB₂–SiC composite. The improved oxidation resistance is attributed to the formation of ample liquid borosilicate film below 1300 °C and a compact film of zirconium silicate above 1300 °C. The formed borosilicate and zirconium silicate on the surface of ZrB₂–SiC–BN ceramics act as an effective barriers for further diffusion of oxygen into the fresh interface of ZrB₂–SiC–BN.     

Processing,microstructure, and mechanical properties of hot-pressed ZrB2 ceramics with a complex Zr/Si/O-based additive

Densification behavior, microstructure, and mechanical properties of zirconium diboride (ZrB₂) ceramics modified with a complex Zr/Si/O-based additive were studied. ZrB₂ ceramics with 5–20 vol.% additions of Zr/Si/O-based additive were densified to >95% relative density at temperatures as low as 1400°C by hot-pressing. Improved densification behavior of ZrB₂ was observed with increasing additive content. The most effective additive amount for densification was 20 vol.%, hot-pressed at 1400°C (∼98% relative density). Microstructural analysis revealed up to 7 vol.% of residual second phases in the final ceramics. Improved densification behavior was attributed to ductility of the silicide phase, liquid phase formation at the hot-pressing temperatures, silicon wetting of ZrB₂ particles, and reactions of surface oxides. Room temperature strength ranged from 390 to 750 MPa and elastic modulus ranged from 440 to 490 GPa. Vickers hardness ranged from 15 to 16 GPa, and indentation fracture toughness was between 4.0 and 4.3 MPa·m^1/2. The most effective additive amount was 7.5 vol.%, which resulted in high relative density after hot-pressing at 1600°C and the best combination of mechanical properties.     

Influence of sol-gel derived ZrB2 additions on microstructure and mechanical properties of SiBCN composites

A simple method for introducing ZrB₂ using sol-gel processing into a SiBCN matrix is presented in this paper. Zirconium n-propoxide (ZNP), boric acid and furfuryl alcohol (C₅H₆O₂) (FA) were added as the precursors of zirconia, boron oxide and carbon forming ZrB₂ dispersed in a SiBCN matrix. SiBCN/ZrB₂ composites with different contents of ZrB₂ (5, 10, 15, and 20 wt%) were formed at 2000 °C for 5 min by spark plasma sintering (SPS). The microstructures were carefully studied. TEM analysis showed that the as formed ZrB₂ grains were typically 100–500 nm in size and had uniform distribution. HRTEM revealed clean grain boundaries between ZrB₂ and SiC, however, a separation of C near the SiC boundary was observed. The flexural strength, fracture toughness, Young's modulus and Vicker's hardness of composites all improved with the ZrB₂ contents and SiBCN matrix containing 20 wt% of ZrB₂ could reach 351±18 MPa, 4.5±0.2 MPa m^1/2, 172±8 GPa and 7.2±0.2 GPa, respectively. The improvement in fracture toughness can be attributed to the tortuous crack paths due to the presence of reinforcing particles.     

Mechanical behavior of two-step hot-pressed ZrB2-based composites with ZrSi2

In this study, fully dense ZrB₂-based composites containing ZrSi₂ were sintered using a two-step hot pressing process. The elastic moduli, fracture toughness and flexural strength of the hot-pressed composites were determined. The effects of ZrSi₂ content on densification behavior and properties of the composites were assessed. The results indicated that the ZrSi₂ improved the sinterability of ZrB₂ powders. Fully dense ZrB₂-based composites with ZrSi₂ were obtained at 1550 °C for 20–40 vol.% ZrSi₂-conatining ZrB₂ powders. The microstructure of the resulting composites was fine and homogeneous. The elastic moduli, fracture toughness and flexural strength of the obtained composites depended on ZrSi₂ content. The shear, Young's, and bulk moduli decreased with ZrSi₂ content. The range of fracture toughness values was measured to be 3.8–4.8 MPa m^1/2. The flexural strength, which was 556 MPa, was almost the constant for ZrSi₂ content of 30 vol.% or less. For 40 vol.% ZrSi₂, however, the strength lowered significantly to 382 MPa.     

Influence of milling time on the synthesis,microstructure and mechanical properties of ZrB2SiCZrO2f ceramic composites

Zirconium diboride toughened by silicon carbide and zirconia fiber (ZrB₂SiCZrO_2f) was prepared by using planetary ball mill and the effect of milling time was investigated. The results showed that both the length of fiber and particle size of ZrB₂SiC-matrix were reduced as the ball milling time increased. When milling time varied from 8 h to 12 h, the accumulated fibers and agglomerated particles were observed. The production of a homogeneous ceramic could be successfully achieved by using a combination of 20 h milling time and hot-pressing at 1850 °C for 60 min under a uniaxial load of 30 MPa. The optimal flexural strength and fracture toughness of the hot-pressed ZrB₂SiCZrO_2f ceramics reached 1084 MPa and 6.8 MPa m^1/2, respectively. The main toughening mechanisms were fiber debonding, fiber pull-out and transformation toughening. The results indicated that the ball milling technique was proposed as a potential and simple method to obtain usable quantities of ZrB₂SiCZrO_2f ceramic.     

Densification,microstructure and mechanical properties of ZrB2–SiCw ceramic composites

ZrB₂–SiCw composites were prepared through hot-pressing at a low temperature of 1800 °C, and Al₂O₃ plus Y₂O₃ were added as sintering aids. Analysis revealed that additives may react with impurities (i.e. surface oxygen impurities and residual metallic impurities) to form a transient liquid phase, thus promote the sintering and densification of ZrB₂–SiCw composites. The content of additives was found to have a significant influence on the sinterability, microstructure and mechanical properties of ZrB₂–SiCw composites. ZrB₂–SiCw composite prepared with a small amount of additives (3 vol.%) provided the optimal combination of microstructure (relative density of 98.3%) and excellent properties, including flexural strength of 783 MPa and fracture toughness of 6.7 MPa m^1/2. With further addition of additives, SiC whiskers were inclined to gather together and be enveloped by excessive liquids to form core-rim-like structures, which lead to little decrease in mechanical properties.     

High-strength ZrB2-based ceramics prepared by reactive pulsed electric current sintering of ZrB2–ZrH2 powders

Fully densified ZrB₂-based ceramic composites were produced by reactive pulsed electric current sintering (PECS) of ZrB₂–ZrH₂ powders within a total thermal cycle time of only 35 min. The composition of the final composite was directly influenced by the initial ZrH₂ content in the starting powder batch. With increasing ZrH₂ content, ZrB₂–ZrO₂, ZrB₂–ZrB–ZrO₂ and ZrB₂–ZrB–Zr₃O composites were obtained. The ZrB₂–ZrB–ZrO₂ composite derived from a 9.8 wt% ZrH₂ starting powder exhibited an excellent flexural strength of 1382 MPa combined with a Vickers hardness of 17.1 GPa and a fracture toughness of 5.0 MPa m^1/2. The high strength was attributed to a fine grain size and the removal of B₂O₃ through reaction with Zr. Higher ZrH₂ content starting powders were densified through solution-reprecipitation resulting in the formation of coarser angular ZrB₂–ZrB composites with a Zr₃O grain boundary phase with a fracture toughness of 5.0 MPa m^1/2 and an acceptable strength in the 852–939 MPa range.     

Enhanced toughness and strength of boron carbide ceramics with reduced graphene oxide fabricated by hot pressing

Boron carbide (B₄C) hybrids with different contents of graphene oxide (GO) were prepared by a heterogeneous co-precipitation method using cetyltrimethyl ammonium bromide (CTAB) as the cationic surfactant. The as-obtained mixtures were further hot-pressed at 1950 °C for 60 min under 30 MPa, by which B₄C–reduced GO (rGO) composites were fabricated. It was found that the addition of only 0.5 wt% rGO could alter the predominance of trans-granular fracture in monolithic B₄C ceramic material to mixed trans-granular and inter-granular modes in B₄C–rGO composites. The flexural strength and fracture toughness of the B₄C–2 wt% rGO were increased by 31% (from 350 to 455 MPa) and 83% (from 3.20 to 5.85 MPa·m^1/2), respectively, compared with those of pure B₄C. The improved mechanical properties are attributed to the mechanisms of pull-out and bridging of rGO and crack deflection, as evidenced by microstructural observations. The energy dissipation in the present B₄C–rGO composites was further verified using two micromechanical models.     

Effect of manganese addition on sintering behavior and mechanical properties of alumina toughened zirconia

The effect of MnO₂ additives on the sintering behavior and mechanical properties of alumina-toughened zirconia (ATZ, with 10 vol% alumina) composites was investigated by incorporating different amounts of MnO₂ (0, 0.5, 1.0, and 1.5 wt%) and sintering at various temperatures ranging from 1300 to 1450 °C. The addition of MnO₂ up to 1.0 wt% improved the sintered density, hardness, flexural strength, and fracture toughness of the composite. However, the addition of 1.5 wt% MnO₂ degraded the relative density, hardness, and flexural strength of the composite due to the transformation of the ZrO₂ phase from tetragonal to monoclinic and grain coarsening. Optimal results were obtained with 1.0 wt% MnO₂ and sintering at 1450 °C, which improved the mechanical properties (hardness: 13.5 GPa, flexural strength: 1.2 GPa, fracture toughness: 8.5 MPa m^1/2) and lowered the sintering temperature compared to the conventional sintering temperature of ATZ composites (1550 °C). Thus, the ATZ composite doped with MnO₂ is a promising material for structural engineering ceramics owing to its improved mechanical properties and lower sintering temperature.     

Spark plasma sintering of polycrystalline La0.6Ce0.3Pr0.1B6–ZrB2 composites

This paper has studied the densification, microstructure, and properties of polycrystalline La_0.6Ce_0.3Pr_0.1B₆–ZrB₂ composites prepared by spark plasma sintering (SPS). The highest relative density of 98.7% is obtained at the SPS condition of axial mechanical pressure 50 MPa, sintering temperature 1900°C and holding time 5 min. The Vickers hardness decreases linearly from the maximum value of 21.49 GPa to the value of 8.24 GPa with the tested temperature increased from room temperature to 1000°C. The effects of crack deflection and bridging have resulted in the fracture toughness of 4.56 MPa m^1/2 of dense polycrystalline La_0.6Ce_0.3Pr_0.1B₆–ZrB₂ composite. The J_1kV of 7.02 A/cm² obtained at 1600°C, the work function of 2.743 eV determined by ultraviolet photoelectron spectroscopy, and the good oxidation resistance below 1100°C in air have revealed that the dense polycrystalline La_0.6Ce_0.3Pr_0.1B₆–ZrB₂ composite has a good potential to be a promising hot cathode material.     

Effect of sintering temperature on electrical properties of SiC/ZrB2 ceramics

SiC/20?wt% ZrB₂ composite ceramics were fabricated via pressureless solid phase sintering in argon atmosphere at different temperature. The effect of sintering temperature on microstructure, electrical properties and mechanical properties of SiC/ZrB₂ ceramics was investigated. Electrical resistivity exhibits twice significant decreases with increasing sintering temperature. The first decrease from 1900?°C to 2000?°C is attributed to the obvious decrease of continuous pore channels in as-sintered materials. The second decrease from 2100?°C to 2200?°C results from the improvement of carbon crystallization and the disappearance of amorphous layers enveloping ZrB₂ grains. Additionally, the increase of sintered density with increasing temperature caused greatly advance of flexural strength, elastic modulus and Vickers hardness. But excessive temperature is detrimental to flexural strength because of SiC grain growth.     

A novel ZrB2-based composite manufactured with Ti3AlC2 additive

A novel ZrB₂–Ti₃AlC₂ composite was densified using spark plasma sintering at 1900 °C under pressure of 30 MPa for 7 min. The effect of Ti₃AlC₂ MAX phase on the densification behavior, microstructural evolutions, phase arrangement, and mechanical properties of the composite were investigated. The phase analysis and microstructural studies revealed the decomposition of the MAX phase at the initial steps of the SPS process. The structural characteristics and surface morphology of the in-situ synthesized reinforcements were verified using X-ray diffraction and scanning electron microscopy, respectively. The formation mechanism of each reinforcement phase was also investigated using thermodynamical assessments. The prepared ZrB₂–Ti₃AlC₂ composite not only possessed a near fully-dense characteristic having an excellent hardness of 31 GPa, but also unexpectedly presented high fracture toughness. The indentation fracture toughness of the composite was calculated as 7.8 MPa m^1/2, which is unprecedented compared with the same class of hard ZrB₂-based composites. Indeed, the superior mechanical properties of the composite achieved in this study was obtained by the homogenous distribution of Al-based reinforcements, formation of hard interfacial ZrC grains, and solid solutions provided by Ti-based phases. The correlations between the phase arrangement, microstructure, and the attained mechanical properties of the composite were comprehensively discussed.