Preparation and properties of MgAl2O4 spinel ceramics by double-doped CeO2 and La2O3

Magnesium aluminate spinel (MgAl₂O₄) ceramics are high-performance and carbon-free materials widely used in both military and civilian fields. However, it is usually challenging to densify during the solid-state sintering process. The excellent properties of some rare earth oxides have been proved to promote the densification of MgAl₂O₄ spinel ceramics. But the mechanism of promoting sintering is not clear. In the present work, MgAl₂O₄ spinel ceramics have been successfully fabricated by co-doping CeO₂ and La₂O₃ via a single-stage solid-state reaction sintering. The effects of addition amounts of CeO₂ and La₂O₃ on phase compositions, microstructures, sintering characteristics, cold compressive strength, and thermal shock resistance of as-prepared MgAl₂O₄ spinel ceramics were systematically investigated. The results show that by co-doping CeO₂ and La₂O₃ can increase the defect concentration due to the lattice distortion. This could promote the movement of Al³⁺ and Mg²⁺ at high temperature, which is beneficial to the formation of more secondary MgAl₂O₄ spinel. t-ZrO₂ with more Ce⁴⁺ filling between spinel grains could prevent the growth of grains and promote the densification, besides the new-formed LaAlO₃ that was mainly distributed along the grain boundary of the MgAl₂O₄ phase, both of which were favorable for the formation of dense microstructure of MgAl₂O₄ spinel materials. At the same time, the formation of more secondary MgAl₂O₄ spinel and sintering densification also improve the mechanical properties of spinel ceramics. La³⁺ will segregate to the spinel grain boundary, preventing grain boundary movement and absorbing the main crack's fracture energy. With 3 wt% CeO₂ and 3 wt% La₂O₃ co-doping, the bulk density of the sample increased from 3.02 g∙cm⁻³ to 3.55 g∙cm⁻³; the apparent porosity decreased from 12.21% to 9.97%; the cold compressive strength increased from 172.88 MPa to 189.54 MPa; and the residual strength retention ratio after thermal shock increased from 84.92% to 89.15%.     

Facile synthesis of pseudocapacitive Mn3O4 nanoparticles for high-performance supercapacitor

In this work, a facile method to produce the ultrafine (4–14 nm) and mixed valence Mn₃O₄ nanoparticles from low-cost MnSiO₃ (manganese silicate) particles were introduced. The best NaOH concentration in hydrothermal treatment has been determined after a series of experiments. Also, the as-synthesized Mn₃O₄ material with good specific capacitance has been investigated attentively at a high mass loading (∼3 mg cm⁻²). The particles size and the pore size distribution is found to be refined and optimized, respectively. This increased the crystallinity and the capacitive contribution in the energy process. Thereby improving the rate capability and cycling stability, which result in significant improvement of specific capacitance (401 F g⁻¹ at 10 mV s⁻¹). The aqueous asymmetric supercapacitor device AC//Mn₃O₄ with a stable working voltage window up to 2.0 V has been fabricated, and it is found to have an energy density of 40.2 W h kg⁻¹ at 500 W kg⁻¹ power density. This could sustain 5000 cycles galvanostatic charge/discharge with 96.9% retention.     

Hierarchical Co3O4@ZnWO4 core/shell nanostructures on nickel foam: Synthesis and electrochemical performance for supercapacitors

To improve the electrochemical properties of Co₃O₄ for supercapacitors application, a hierarchical Co₃O₄@ZnWO₄ core/shell nanowire arrays (NWAs) material is designed and synthesized successfully via a facile two-step hydrothermal method followed by the heat treatment. Co₃O₄@ZnWO₄ NWAs exhibits excellent electrochemical performances with areal capacitance of 4.1 F cm⁻² (1020.1 F g⁻¹) at a current density of 2 mA cm⁻² and extremely good cycling stability (99.7% of the initial capacitance remained even after 3000 cycles). Compared with pure Co₃O₄ electrodes, the results prove that this unique hierarchical hybrid nanostructure and reasonable assembling of two electrochemical pseudocapacitor materials are more advantageous to enhance the electrochemical performance. Considering these remarkable capacitive behaviors, the hierarchical Co₃O₄@ZnWO₄ core/shell NWAs nanostructure electrode can be revealed promising for high-performance supercapacitors.     

Fabrication of efficient nanostructured Co3O4-Graphene bifunctional catalysts: Oxygen evolution,hydrogen evolution,and H2O2 sensing

Nanostructured Co₃O₄-graphene hybrid catalysts are fabricated by a one-step vacuum kinetic spray technique from microparticles of Co₃O₄ and graphite powders. The Co₃O₄-graphene hybrid catalysts with various Co₃O₄ contents are studied concerning the oxygen evolution reaction (OER), and hydrogen evolution reaction (HER) in 1.0 M KOH, as well as, H₂O₂ sensing in 0.1 M NaOH. We find that increasing graphene content in the hybrid catalysts results in an overall improvement of the OER electrocatalytic activity due to the enhancement in the charge transfer kinetics. The hybrid catalyst with 25 wt% Co₃O₄ reveals the optimum electrocatalytic activity toward the OER with the lowest overpotential (η) of 283 mV@ 10 mA cm⁻² and superior reaction kinetics with a low Tafel slope of 25 mV dec⁻¹. Besides, the OER stability at 50 mA cm⁻² for 50 h in 1.0 M KOH was verified. The hybrid catalyst with 50 wt% Co₃O₄ revealed the highest activity toward the HER with η of 108 mV@ 10 mA cm⁻², Tafel slope of 90 mV.dec⁻¹, and stability at 50 mA cm⁻² for nearly 30 h. Moreover, it reveals ultrahigh H₂O₂ amperometric detection with superior sensitivity of 18,110 μA mM⁻¹ cm⁻², linear detection range from 20 μM to 1 mM, and a limit of detection of 0.14 μM.     

Facile synthesis of NiMn2O4 nanosheet arrays grown on nickel foam as novel electrode materials for high-performance supercapacitors

Nanostructured spinel NiMn₂O₄ arrays have been fabricated by a facile hydrothermal approach and further investigated as binder-free electrode for high-performance supercapacitors. Compared with Mn₃O₄, NiMn₂O₄ exhibited higher specific capacitances (662.5 F g⁻¹ and 370.5 F g⁻¹ in different electrolytes at the current density of 1 A g⁻¹) and excellent cycling stability (~96% capacitance retention after 1000 cycles) in a three-electrode system. Such a novel microstructure grown directly on the conductive substrate provided sufficient active sites for redox reaction resulting in their enhanced electrochemical behaviors. Their improved performances suggested that ultrathin sheet-like NiMn₂O₄ arrays on Ni foam substrate were a promising electrode material for supercapacitors.     

Luminescence of MgAl2O4 and ZnAl2O4 spinel ceramics containing some 3d ions

The luminescence properties of ceramic phosphors based on two spinel hosts MgAl₂O₄ and ZnAl₂O₄ doped with manganese ions have been studied. It has been found that the spectral properties of these phosphors can be strongly varied by changing synthesis conditions. Both types of doped ceramic spinel can serve as efficient Mn²⁺ green-emitting phosphors having peak emissions at 525 and 510 nm, respectively. Mn-doped MgAl₂O₄ spinel can also be prepared as an efficient Mn⁴⁺ red-emitting phosphor having peak emission at ~651 nm by using specific temperatures of heat treatment in air. It has also been shown that the conversion of Mn²⁺ to Mn⁴⁺ and viсe versa, as well as the coexistence of Mn²⁺ green and Mn⁴⁺ red emissions, can be accomplished by properly chosen annealing conditions of the same initially synthesized MgAl₂O₄:Mn sample. Manganese doped MgAl₂O₄ spinel with an optimal intensity ratio of green and red emissions can be a promising single-phase bicolor phosphor suitable for the development of warm white phosphor-converted LED lamps. On the other hand, it has been determined that perfectly normal ZnAl₂O₄ spinel cannot be doped with Mn⁴⁺ ions in contrast to partially inverse MgAl₂O₄ spinel. However, ZnAl₂O₄ samples unintentionally doped with impurity Cr³⁺ ions show emission spectra in the far-red region with well pronounced R, N and vibronic lines of Cr³⁺ luminescence due to the perfect normal spinel structure of synthesized ZnAl₂O₄ ceramics. Also, by partially substituting Al³⁺ cations for Mg²⁺ in ZnAl₂O₄ there is an opportunity to obtain Mn⁴⁺ doped or Mn⁴⁺/Cr³⁺ codoped far-red emitting phosphors which can be suitable for indoor plant growth lighting sources.     

Synthesis of Mn3O4/N-doped graphene hybrid and its improved electrochemical performance for lithium-ion batteries

Mn₃O₄/N-doped graphene (Mn₃O₄/NG) hybrids were synthesized by a simple one-pot hydrothermal process. The scanning electron microscopy (SEM), transition electron microscopy (TEM), X-ray powder diffraction (XRD), Thermogravimetric analysis (TG), Raman Spectroscopy and X-ray photoelectron spectroscopy (XPS) were used to characterize the microstructure, crystallinity and compositions. It is demonstrated that Mn₃O₄ nanoparticles are high-dispersely anchored onto the individual graphene nanosheets, and also found that, in contrast with pure Mn₃O₄ obtained without graphene added, the introduction of graphene effectively restricts the growth of Mn₃O₄ nanoparticles. Simultaneously, the anchored well-dispersed Mn₃O₄ nanoparticles also play a role as spacers in preventing the restacking of graphene sheets and producing abundant nanoscale porous channels. Hence, it is well anticipated that the accessibility and reactivity of electrolyte molecules with Mn₃O₄/NG electrode are highly improved during the electrochemical process. As the anode material for lithium ion batteries, the Mn₃O₄/NG hybrid electrode displays an outstanding reversible capacity of 1208.4 mAh g⁻¹ after 150 cycles at a current density of 88 mA g⁻¹, even still retained 284 mAh g⁻¹ at a high current density of 4400 mA g⁻¹ after 10 cycles, indicating the superior capacity retention, which is better than those of bare Mn₃O₄, and most other Mn₃O₄/C hybrids in reported literatures. Finally, the superior performance can be ascribed to the uniformly distribution of ultrafine Mn₃O₄ nanoparticles, successful nitrogen doping of graphene and favorable structures of the composites.     

Surface modification and dispersion of ceramic particles using liquid-liquid extraction method for application in supercapacitor electrodes

Particle extraction through liquid-liquid interface (PELLI) was used for the extraction of MnO₂, Mn₃O₄, FeOOH and ZnO particles from an aqueous synthesis medium to the n-butanol phase. The benefits of PELLI were demonstrated by the fabrication of supercapacitor electrodes, which showed good electrochemical performance at high active mass loadings. Octyl gallate (OG) was found to be an efficient and versatile extractor for the ceramic particles. The phase transfer of the particles resulted in reduced agglomeration, which allowed for improved electrolyte access to the particle surface and facilitated their mixing with conductive multiwalled carbon nanotube (MWCNT) additives. It was shown that OG is a promising extractor material for the fabrication of ceramic-ceramic, ceramic-metal and ceramic-MWCNT nanocomposites. The strong adsorption of OG on the particle surface involved bridging or chelating bidentate bonding of the catechol group to the metal atoms. The capacitive properties of FeOOH-MWCNT electrodes were tested in the negative potential window. MnO₂-MWCNT and Mn₃O₄-MWCNT electrodes were investigated for charge storage in the positive potential window. The highest capacitance of 5.7 F cm⁻² for positive electrodes was achieved using MnO₂-MWCNT composites with active mass loading of 36 mg cm⁻². The Mn₃O₄-MWCNT electrodes exhibited improved capacitance retention at high charge-discharge rates.     

Properties of CuMn1.5Ni0.5O4 spinel as high-performance cathode for solid oxide fuel cells

Spinel oxide cathode has made great progress in solid oxide fuel cells (SOFCs) because of its special characteristics different from perovskite. In this study, a spinel-structured SOFC cathode, CuMn_1.5Ni_0.5O₄ (CMN), is proposed. Rietveld refinement shows that CMN takes the cubic structure of the space group of P4₃32. CMN shows a high conductivity of about 70.0–91.2 S cm⁻¹ at 600–800 ºC in the air and exhibits good catalytic activity for oxygen. A symmetric cell with CMN-GDC composite cathode demonstrates a low Rp of 0.047 Ω cm² at 800 ºC. The charge transfer of oxygen is the rate-limiting process at lower temperatures. The performance test results of the button cell with CMN-GDC composite cathode are excellent, with high power densities of 1342.4 mW cm⁻² at 800 ºC. After a110h long-term test, the cell runs stably, and no microstructure damage is observed.     

Fabrication of CuFe2O4@g-C3N4@GNPs nanocomposites as anode material for supercapacitor applications

The aim of this study was to synthesize CuFe₂O₄ together with g-C₃N₄ and GNPs in various combinations on the surface of Ni foam for use as anode materials in supercapacitors. The fabricated electrodes were investigated by XRD, FTIR, XPS, BET, SEM and TEM for content and by CV, GCD and EIS analysis for electrochemistry. The characterization results showed that CuFe₂O₄ was successfully synthesized together with g-C₃N₄ and GNPs in a nanosponge-like geometry. The highest value of specific capacitance was found to be 989 mF/cm² at 2 mA measurement in the triple combination. Moreover, the stability of this electrode was measured to be 70% after 1500 cycles at 16 mA, while the energy and power densities were calculated to be 27.8 mWh/cm² and 300 mW/cm², respectively. The EIS results show that the carbon-based component increased the Cs value by decreasing the charge transfer and diffusion resistances of the electrodes. Compared to its counterparts in the literature, its Cs value is quite high, but its stability is low, so it can be used in low-cycle applications.     

A green strategy for the synthesis of graphene supported Mn3O4 nanocomposites from graphitized coal and their supercapacitor application

A by-product free strategy based on modified Hummers method was proposed to synthesize graphene/Mn₃O₄ composites without any additional manganese source. Coal-derived graphite (CDG) was used as carbon source instead of conventional natural graphite flakes and MnSO₄ produced from the modified Hummers was in situ transformed into Mn₃O₄ by precipitation in air. After reduction with hydrazine, the reduced coal-derived graphene oxide/Mn₃O₄ (RCDGO/Mn₃O₄) was obtained and employed as the electrode material for the supercapacitors. In addition, K₂SO₄ produced from the modified Hummers was used as electrolyte, as a result, residual-free was achieved during the whole process, and the atom utilization was calculated as high as about 97%. A maximum specific capacitance of 260 F g⁻¹ was achieved for RCDGO/Mn₃O₄ composite with 86% Mn₃O₄ in saturated K₂SO₄ electrolyte solution based on the synergetic effects between coal-derived graphene and attached Mn₃O₄ nanoparticles. Its specific energy density reached 8.7 Wh kg⁻¹ at a current density of 50 mA g⁻¹ when used as a symmetrical supercapacitor. The good capacitance retention (92–94%) was also observed after 1000 continuous cycles of galvanostatic charge–discharge.     

MWCNTs-GONRs/Co3O4 electrode with needle-like arrays for outstanding supercapacitors

Multiwalled carbon nanotubes-graphene oxide nanoribbons (MWCNTs-GONRs) exhibit high specific surface area and good electroconductivity because of their unique three-dimensional cross-linking structure with the properties of both CNTs and GONRs. In this study, a hydrothermal method was employed to anchor MWCNTs–GONRs onto a Ni foam (NF) to obtain a precursor substrate. Subsequently, Co₃O₄ arrays were grown on the NF substrate to synthesize a MWCNTs–GONR/Co₃O₄ electrode. The electrode showed a capacitance of 846.2 F g⁻¹ at 1 A g⁻¹ and a capacitance retention of 90.1% after 3000 cycles. Furthermore, MWCNTs–GONRs/Co₃O₄ and active carbon (AC) were used as the positive and negative electrodes, respectively, to assemble a supercapacitor, which delivered a maximum energy density of 38.23 W h kg⁻¹ and a high power density of 6.80 kW kg⁻¹. In addition, the specific capacitance of the device reached a maximum of 91.5% after 9000 cycles. Thus, the MWCNTs–GONRs/Co₃O₄ electrode showed huge potential for supercapacitor applications.     

NiFe-NiFe2O4/rGO composites: Controlled preparation and superior lithium storage properties

Binary transition-metal oxides with spinel structure have great potential as advanced anode materials for lithium-ion batteries (LIBs). Herein, NiFe-NiFe₂O₄/ reduced graphene oxide (rGO) composites are obtained via a facile cyanometallic framework precursor strategy to improve the lithium storage performance of NiFe₂O₄. In the composites, NiFe-NiFe₂O₄ nanoparticles with adjustable mass ratios of NiFe₂O₄ to NiFe alloy are homogeneously deposited on rGO sheets. As anode material for LIBs, the optimized NiFe-NiFe₂O₄/rGO composite displays remarkably enhanced lithium storage performance with an initial specific capacity as high as 1362 mAh g⁻¹ at 0.1 A g⁻¹ and a decent capacity retention of ca. 80% after 130 cycles. Besides, the composite delivers a reversible capacity of 550 mAh g⁻¹ at 1 A g⁻¹ after 300 cycles. During the charge–discharge cycles, the aggregation of the NiFe-NiFe₂O₄ nanoparticles and the structural collapse of the electrode can be well alleviated by rGO sheets. Moreover, the conductivity of the electrode can be significantly improved by the well-conductive NiFe alloy and rGO sheets. All these contribute to the improved lithium storage performance of NiFe-NiFe₂O₄/rGO composites.     

Formation of sol–gel derived (Cu,Mn,Co)3O4 spinel and its electrical properties

An (Mn,Co)₃O₄ spinel layer effectively suppresses Cr outward diffusion, but the occurrence of spallation between coating and metal interfaces and the increasing oxidation rate over time significantly deteriorate cell performance. A transition metal cation, particularly Cu, is added into the (Mn,Co)₃O₄ to improve the long-term stability of the interconnect materials for low-to-intermediate-temperature solid oxide fuel cells (SOFCs). In this work, fine-crystalline (Cu,Mn,Co)₃O₄ spinel powders with an average crystallite size of 21 nm were successfully synthesized via the citric acid–nitrate method. The potential for use as a coating material for low-to-intermediate-temperature SOFC interconnects was explored. According to the TG curves, IR spectra, and XRD patterns, 800 °C is recommended as the minimum calcination temperature for (Cu,Mn,Co)₃O₄ spinel materials. Compared with (Mn,Co)₃O₄ spinel materials, the addition of Cu does not induce significant changes in the crystal structure but markedly improves the electrical conductivity (116 Scm⁻¹) and the activation energy (0.394 eV) of the (Cu,Mn,Co)₃O₄ spinel. Overall, the sol–gel derived (Cu,Mn,Co)₃O₄ spinel can be used as a coating material for low-to-intermediate-temperature SOFC interconnects and is superior to (Mn,Co)₃O₄ spinel because high electrical conductivity is preferred to minimize ohmic losses between the electrodes of adjacent cells.     

Preparation and characterization of manganese oxide/CNT composites as supercapacitive materials

Manganese oxide was synthesized and dispersed on carbon nanotube (CNT) matrix by thermally decomposing manganese nitrates. CNTs used in this paper were grown directly on graphite disk by chemical vapor deposition technique. The capacitive behavior of manganese oxide/CNT composites was investigated by cyclic voltammetry and galvanostatic charge–discharge method in 1 M Na₂SO₄ aqueous solutions. When the loading mass of MnO₂ is 36.9 μg cm^− 2, the specific capacitance of manganese oxide/CNT composite (based on MnO₂) at the charge–discharge current density of 1 mA cm^− 2 equals 568 F g^− 1. Additionally, excellent charge–discharge cycle stability (ca. 88% value of specific capacitance remained after 2500 charge–discharge cycles) and power characteristics of the manganese oxide/CNT composite electrode can be observed. The effect of loading mass of MnO₂ on specific capacitance of the electrode has also been investigated.     

One-pot hydrothermal synthesis of Mn3O4 nanorods grown on Ni foam for high performance supercapacitor applications

Mn₃O₄/Ni foam composites were synthesized by a one-step hydrothermal method in an aqueous solution containing only Mn(NO₃)₂ and C₆H₁₂N₄. It was found that Mn₃O₄ nanorods with lengths of 2 to 3 μm and diameters of 100 nm distributed on Ni foam homogeneously. Detailed reaction time-dependent morphological and component evolution was studied to understand the growth process of Mn₃O₄ nanorods. As cathode material for supercapacitors, Mn₃O₄ nanorods/composite exhibited superior supercapacitor performances with high specific capacitance (263 F · g^-1 at 1A · g^-1), which was more than 10 times higher than that of the Mn₃O₄/Ni plate. The enhanced supercapacitor performance was due to the porous architecture of the Ni foam which provides fast ion and electron transfer, large reaction surface area, and good conductivity.     

One-step solvothermal synthesis of spherical spinel type NiFe2−xMnxO4-RGO as high-performance supercapacitor electrodes

A facile route for the synthesis of spinel type NiFe_2−xMn_xO₄-RGO as supercapacitor electrodes is reported and the microstructure, elemental composition/content, morphology and thermal stability of NiFe_1.7Mn_0.3O₄-RGO₁₀ were characterized by XRD, FTIR, ICP, XPS, TEM, and TGA. Uniform NiFe_1.7Mn_0.3O₄ nanospheres were deposited densely on the reduced graphene oxide (RGO) sheets. The as prepared NiFe_1.7Mn_0.3O₄-RGO₁₀ composite showed better electrochemical performance than the corresponding binary metal systems. The spinel structure and the doping of Mn as the third component provided the composite with high specific capacitance of 1214.7 F g⁻¹ at 0.5 A g⁻¹ in a three-electrode system along with good cycling stability.     

Micro/nanostructured Bi2Mn4O10 with hierarchical spindle morphology as a highly efficient anode material for lithium-ion batteries

Mullite-type compound Bi₂Mn₄O₁₀ has shown the feasibility as anodes of next lithium-ion batteries (LIBs). Herein micro/nano-Bi₂Mn₄O₁₀ with hierarchical spindle-like architectures has been successfully synthesized using a one-step hydrothermal method without any no surfactant or template. A time-dependent experiment is carried out to observe the morphology evolution, suggesting a nucleation–aggregation/growth–dissolution–recrystallization process. As anode of LIBs, the as-prepared spindle-shaped micro/nano Bi₂Mn₄O₁₀ harvests a significantly high initial discharge capacity of 1022 mA h g⁻¹ at 1 C, an excellent cyclability performance (563.8 mA h g⁻¹ after 400 cycles), a better high-rate capability (100 mA h g⁻¹ at 10 C), quick diffusion kinetics (1.8 × 10⁻¹² cm² s⁻¹), and low active energy (19.5 kJ mol⁻¹), which are significantly superior to that of its bulk counterparts and the previous reports. The encouraging lithium storage performance largely stems from the synergistic effect of the unique spindle-shaped micro/nanostructure.     

Role of Mn doping on magnetic properties of multiferroic NiCr2O4 nanoparticles

The structural and magnetic properties of Mn doped Nickel Chromite (Ni_1-xMn_xCr₂O_4, x = 0, 0.2, 0.3, 0.4, 0.6, 0.8) nanoparticles (NPs) were studied in detail. The X-ray diffraction analysis affirms normal spinel structure for all the samples and average crystallite size was found in the range 31–58 nm. The spinel structure of these nanoparticles was also confirmed by Fourier transform infrared spectroscopy which revealed the formation of tetrahedral and octahedral vibrational bands in the range 607 -628 cm^?1 and 486 - 491 cm^?1, respectively. Transmission electron microscopy images depicts less agglomerated and non-spherical shaped NPs. The temperature dependent zero field cooled and field cooled magnetic measurements revealed a paramagnetic to ferrimagnetic transition T_c at 87 K for NiCr₂O₄ NPs, which is shifted to low temperatures by Mn doping. This effect was attributed to cationic distributions between adjacent sites produced by Mn doping. M ? H loops of Ni_1-xMn_xCr₂O₄ NPs revealed enhanced saturation magnetization with increase in Mn doping which is attributed to a large magnetic moment of Mn ions. Ni_1-xMn_xCr₂O₄ (x = 0.6 and 0.8) NPs show steps in their M ? H loops because of exchange interactions between two sites of these NPs.     

Synthesis and electrochemistry of 5 V LiNi0.4Mn1.6O4 cathode materials synthesized by different methods

Spinel LiNi_0.4Mn_1.6O₄ has been successfully synthesized by ultrasonic-assisted co-precipitation (UACP) method. The structure and physicochemical properties of this as-prepared powder compared with the LiNi_0.4Mn_1.6O₄ synthesized by co-precipitation method were investigated by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge–discharge test in detail. XRD and SEM show that all samples have high phase purity, and ultrasonic process plays an important role in controlling morphology; FT-IR reveals that the Mn(III)–O stretching band at 511 cm^?1 has a red shift to 503 cm^?1, and the Mn(IV)–O stretching band at 612 cm^?1 has a blue shift to 622 cm^?1 because of the doped Ni. CV confirms that the LiNi_0.4Mn_1.6O₄ sample (UACP) has bigger area of the reduction peaks than that of sample synthesized by co-precipitation method, indicating that the former has higher discharge capacity than that of the latter. Galvanostatic charge–discharge test indicates that the initial discharge capacities for the LiNi_0.4Mn_1.6O₄ (UACP) at C/5 and 1C are 129 and 116 mAh g^?1, respectively. After 100 cycles, their capacity retentions are 94.6% and 85.3%, respectively. EIS indicates that LiNi_0.4Mn_1.6O₄ samples synthesized by UACP method have smaller charge transfer resistance than that of samples synthesized by co-precipitation method corresponding to the extraction of Li⁺ ions.