The new complex high-entropy metal boron carbonitride: Microstructure and mechanical properties

In this contribution, the ternary BCN anion systems of high-entropy ceramics (HEC) are consolidated by hot-pressing sintering and the impacts of sintering temperature and the content of amorphous BCN addition on microstructural evolution and mechanical performance were evaluated. Results confirmed that high-entropy, oxide, and BN(C) phases were precipitated for (Ta_0.2Nb_0.2Zr_0.2Hf_0.2Ti_0.2)(B, C, N) ceramics after sintering at 1900°C. With the decrease of BCN addition, a new phase of MiB₂ (Mi representing the metal atoms) occurred. The Vickers hardness, bending strength, elastic modulus, and fracture toughness of the optimized bulk HECs were investigated, obtained at 24.5 ± 2.3 GPa, 522.0 ± 2.6 MPa, 478.9 ± 11.1 GPa, and 5.36 ± 0.56 MPa m^1/2, respectively.     

Dissolving and stabilizing soft WB2 and MoB2 phases into high-entropy borides via boron-metals reactive sintering to attain higher hardness

Five single-phase WB₂- and MoB₂-containing high-entropy borides (HEBs) have been made via reactive spark plasma sintering of elemental boron and metals. A large reactive driving force enables the full dissolution of 10−20 mol. % WB₂ to form dense, single-phase HEBs, including (Ti_0.2Zr_0.2Hf_0.2Mo_0.2W_0.2)B₂, (Ti_0.2Ta_0.2Cr_0.2Mo_0.2W_0.2)B₂, (Zr_0.2Hf_0.2Nb_0.2Ta_0.2W_0.2)B₂, and (Zr_0.225Hf_0.225Ta_0.225Mo_0.225W_0.1)B₂; the successful fabrication of such single-phase WB₂-containing HEBs has not been reported before. In the processing science, this result serves perhaps the best example demonstrating that the phase formation in high-entropy ceramics can strongly depend on the kinetic route. A scientifically interesting finding is that HEBs containing softer WB₂ and/or MoB₂ components are significantly harder than (Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)B₂ (with harder binary boride components). This exemplifies that high-entropy ceramics can achieve unexpected properties.     

Microstructures and oxidation mechanisms of (Zr0.2Hf0.2Ta0.2Nb0.2Ti0.2)B2 high-entropy ceramic

A nano dual-phase powder with great sinterability was synthesized by molten-salt assisted borothermal reductions at 1100 °C using B, ZrO₂, HfO₂, Ta₂O₅, Nb₂O₅ and TiO₂ powders as raw materials. Single-phase (Z_r0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ high-entropy ceramic was prepared by spark plasma sintering using the as-synthesized nano dual-phase powder. Oxidation behavior of the (Zr_0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ ceramic was investigated over the range of 30–1400 °C in air and the result indicated that the rapid oxidation of ceramic began at 1300 °C. The phenomenon could be ascribed to the rapid volatilization of B₂O₃ from oxide scale. A layered structure was formed at the cross section of (Zr_0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ ceramic after oxidation. The relationship between partial pressures of gaseous metal oxides and oxygen partial pressures was calculated, which inferred that the formation of layered structure could be ascribed to the active oxidation of (Zr_0.2Hf_0.2Ta_0.2Nb_0.2Ti_0.2)B₂, the generation of gaseous metal oxides, their outward diffusion and further oxidation.     

Microstructure and mechanical properties of high-entropy borides derived from boro/carbothermal reduction

Starting from metal oxides, B₄C and graphite, a suite of high-entropy boride ceramics, formulated (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)B₂, (Hf_0.2Zr_0.2Mo_0.2Nb_0.2Ti_0.2)B₂ and (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ derived from boro/carbothermal reduction at 1600 °C were fabricated by spark plasma sintering at 2000 °C. It was found that the synthetic high-entropy boride crystalized in hexagonal structure and the yield of the targeting phase was calculated to be over 93.0 wt% in the sintered ceramics. Benefitting from the nearly full densification (96.3% ˜ 98.5% in relative density) and the refined microstructure, the products exhibited the relatively high Vickers hardness. The indentation fracture toughness was determined to be comparable with the single transition metal-diboride ceramics. It should be noted that the formation of high-entropy boride ceramics were featured with the relatively high hardness at no expense of the fracture toughness.     

High-entropy (HfTaTiNbZr)C and (HfTaTiNbMo)C carbides fabricated through reactive high-energy ball milling and spark plasma sintering

Powders of high-entropy Hf_0.2Ta_0.2Ti_0.2Nb_0.2Zr_0.2C (HEC_Zr) and Hf_0.2Ta_0.2Ti_0.2Nb_0.2Mo_0.2C (HEC_Mo) carbides were fabricated through the reactive high-energy ball milling (R-HEBM) of metal and graphite particles. It was found that 60 min of R-HEBM is adequate to achieve a full conversion of the initial precursors into a FCC solid solution for both compositions. The HEC_Zr powder possesses a unimodal particle size distribution (40% d ≤ 1 μm, 95% d ≤ 10 μm), and the HEC_Mo powder features a bimodal distribution with a slightly larger particle size overall (30% d ≤ 1 μm, 80% d ≤ 10 μm). Bulk high-entropy ceramics with a minor presence of an oxide phase were fabricated through the spark plasma sintering of these high-entropy powders at 2000 °C with a 10 min dwelling time. The HEC_Zr ceramics possess a relative density of up to 94.8%, hardness of 25.7 ± 3.5 GPa, Young's modulus of 473 ± 37 GPa, and thermal conductivity of 5.6 ± 0.1 W/m·K. HEC_Mo ceramics with a relative density of up to 93.8%, hardness of 23.8 ± 2.7 GPa, Young's modulus of 544 ± 48 GPa, and thermal conductivity of 5.9 ± 0.2 W/m·K were also fabricated. A comparison of the properties of the HECs produced in this study and those previously reported is also provided.     

Oxidation behavior of high-entropy carbide (Hf0.2Ta0.2Zr0.2Ti0.2Nb0.2)C at 1400–1600 °C

Oxidation behavior of high-entropy carbide (Hf_0.2Ta_0.2Zr_0.2Ti_0.2Nb_0.2)C (HTZTNC) was investigated over temperature range of 1400–1600 °C. Results showed improved oxidation resistance of high-entropy carbide compared with individual carbide ceramics. In oxide layer, Ta₂O₅ and Nb₂O₅ were found to be dominant phases at 1400 °C, whereas ZrTiO₄ and HfTiO₄ were main phases obtained at 1500 and 1600 °C. Moreover, these complex dense oxide layer structures on the surface of HTZTNC at high temperature led to excellent oxidation resistance. The observation of Ti-depleted layer at 1500 and 1600 °C after 20 min of oxidation indicated that oxidation mechanism involved outward diffusion of titanium oxide, which was further confirmed by reoxidation experiments. In sum, these findings are promising for future development of high-entropy ultrahigh temperature ceramics with good oxidation resistance.     

Fine-grained dual-phase high-entropy ceramics derived from boro/carbothermal reduction

In the current work, fine-grained dual-phase, high-entropy ceramics (Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)B₂-(Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C with different phase ratios were prepared from powders synthesized via a boro/carbothermal reduction approach, by adjusting the content of B₄C and C in the precursor powders. Phase compositions, densification, microstructure, and mechanical properties were investigated and correlated. Due to the combination of pinning effect and the boro/carbothermal reduction approach, the average grain size (～0.5?1.5 μm) of the dual-phase high-entropy ceramics was roughly one order of magnitude smaller than previously reported literature. The dual-phase high-entropy ceramics had residual porosity ranging from 0.3 to 3.2 % upon sintering by SPS and the material with about 18 vol% boride phase exhibited the highest Vickers hardness (24.2±0.3 GPa) and fracture toughness (3.19±0.24 MPam^1/2).     

Ultra high temperature high-entropy borides: Effect of graphite addition on oxides removal and densification behaviour

The introduction of 0.5–1.0 wt.% graphite to the powders prepared by Self-propagating High-temperature Synthesis (SHS) is found to be highly beneficial for the removal of oxide impurities (from 2.7-8.8 wt.% to 0.2–0.5 wt.%) during spark plasma sintering (1950°C/20 min, 20 MPa) of (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ and (Hf_0.2Mo_0.2Ta_0.2Zr_0.2Ti_0.2)B₂ ceramics. Concurrently, the consolidation level achieved is enhanced from about 92.5% and 88%, respectively, to values exceeding 97%. While a further increase of graphite slightly improves samples densification, final products become progressively richer of the unreacted carbon.It is assumed that graphite plays a double role during SPS, e.g. not only as a reactant during the carbothermal reduction of oxides contaminant, but also as lubricating agent for the powder particles. The latter phenomenon is likely the main responsible for the densification improvement when 3 wt.% or larger amounts of additive are used. Another positive effect is the crystallite size refinement of the high-entropy phases with the progressive abatement of oxides, to confirm that their presence promotes grain coarsening during the sintering process.     

High-entropy carbide-based ceramic cutting tools

In this study, a novel high-entropy carbide-based ceramic cutting tool was developed. The cutting performance of three kinds of high-entropy carbide-based ceramic tools with different mechanical properties for the ISO C45E4 steel were evaluated. Although the pure (Ti_0.2Zr_0.2Nb_0.2Ta_0.2Mo_0.2)C_0.8 ceramic cutting tool exhibited the highest hardness of 25.06 ± 0.32 GPa, the cutting performance was poor due to the chipping and catastrophic failure caused by the low toughness (2.25 ± 0.27 MPa m^1/2). The (Ti_0.2Zr_0.2Nb_0.2Ta_0.2Mo_0.2)C_0.8–15 vol% cobalt cutting tool with highest fracture toughness (6.37 ± 0.24 MPa m^1/2) and lowest hardness (17.29 ± 0.79 GPa) showed the medium cutting performance due to the low wear resistance caused by the low hardness. The (Ti_0.2Zr_0.2Nb_0.2Ta_0.2Mo_0.2)C_0.8–7.7 vol% cobalt cutting tool showed the longest effective cutting life of ∼67 min due to the high wear resistance and chipping resistance caused by the high hardness (21.05 ± 0.72 GPa), high toughness (5.35 ± 0.51 MPa m^1/2), and fine grain size (0.60 ± 0.15 μm). The wear mechanisms of the cobalt-containing (Ti_0.2Zr_0.2Nb_0.2Ta_0.2Mo_0.2)C_0.8 ceramic cutting tools included adhesive wear and abrasive wear and oxidative wear. This research indicated that the high-entropy carbide-based ceramics with high hardness and high toughness have potential use in the field of cutting tool application.     

First-principles prediction,fabrication and characterization of (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)B2 high-entropy borides

The microstructure and mechanical properties of (Hf_0.2Nb_0.2Ta_0.2Ti_0.2Zr_0.2)B₂ high-entropy boride (HEB) were first predicted by first-principles calculations combined with virtual crystal approximation (VCA). The results verified the suitability of VCA scheme in HEB studying. Besides, single-phase (Hf_0.2Nb_0.2Ta_0.2Ti_0.2Zr_0.2)B₂ ceramics were successfully fabricated using boro/carbothermal reduction (BCTR) method and subsequent spark plasma sintering (SPS); furthermore, the effects of different amounts of B₄C on microstructure and mechanical properties were evaluated. Due to the addition of B₄C and C, all samples formed single-phase solid solutions after SPS. When the excess amount of B₄C increased to 5 wt%, the sample with fine grains exhibited superior comprehensive properties with the hardness of 18.1 ± 1.0 GPa, flexural strength of 376 ± 25 MPa, and fracture toughness of 4.70 ± 0.27 MPa m^1/2. Nonetheless, 10 wt% excess of B₄C coarsened the grains and decreased the strength of the ceramic. Moreover, the nanohardness (34.5–36.9 GPa) and Young's modulus (519–571 GPa) values with different B₄C contents just showed a slight difference and were within ranges commonly observed in high-entropy diboride ceramics.     

Fabrication and properties of Cf/(Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C-SiC high-entropy ceramic matrix composites via precursor infiltration and pyrolysis

In this work, C_f/(Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C-SiC high-entropy ceramic matrix composites were reported for the first time. Based on the systematic study of the pyrolysis and solid-solution mechanisms of (Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C precursor by Fourier transform infrared spectroscopy, TG-MS and XRD, C_f/(Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C-SiC with uniform phase and element distribution were successfully fabricated by precursor infiltration and pyrolysis. The as-fabricated composites have a density and open porosity of 2.40 g/cm³ and 13.32 vol% respectively, with outstanding bending strength (322 MPa) and fracture toughness (8.24 MPa m^1/2). The C_f/(Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C-SiC composites also present excellent ablation resistant property at a heat flux density of 5 MW/m², with linear and mass recession rates of 2.89 μm/s and 2.60 mg/s respectively. The excellent combinations of mechanical and ablation resistant properties make the C_f/(Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C-SiC composites a new generation of reliable ultra-high temperature materials.     

The effect of submicron grain size on thermal stability and mechanical properties of high-entropy carbide ceramics

(Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C high-entropy ceramics (HEC) with a submicron grain size of 400 to 600 nm were fabricated by spark plasma sintering using a two-step sintering process. Both X-ray and neutron diffractions confirmed the formation of single-phase with rock salt structure in the as-fabricated (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C samples. The effect of submicron grain size on the thermal stability and mechanical properties of HEC was investigated. The grain growth kinetics in the fine-grained HEC was small at 1300 and 1600°C, suggesting high thermal stability that was possibly related to the compositional complexity and sluggish diffusion in HEC. Compared to the coarse-grain HEC with a grain size of 16.5 µm, the bending strength and fracture toughness of fine-grained HEC were 25% and 20% higher respectively. The improvement of mechanical properties in fine-grained HEC may be attributed to micromechanistic mechanisms such as crack deflection.     

Hardness and toughness improvement of SiC-based ceramics with the addition of (Hf0.2Mo0.2Ta0.2Nb0.2Ti0.2)B2

The influences of different contents ranging 0–15 wt% of high-entropy boride (HEB) (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ on the mechanical properties of SiC-based ceramics using Al₂O₃-Y₂O₃ sintering additives sintered by spark plasma sintering process were investigated in this study. The results showed that the introduction of 5 and 10 wt% (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ could facilitate the densification and the grain growth of SiC-based ceramics via the mechanism of liquid phase sintering. However, the grain growth of SiC-based ceramics was inhibited by the grain boundary pinning effect with the addition of 15 wt% (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂. The SiC-based ceramics with 15 wt% (Hf_0.2Mo_0.2Ta_0.2Nb_0.2Ti_0.2)B₂ showed the enhanced hardness (21.9±0.7 GPa) and high toughness (4.88±0.88 MPa·m^1/2) as compared with high-entropy phase-free SiC-based ceramics, which exhibited a hardness of 16.6 GPa and toughness of 3.10 MPa·m^1/2. The enhancement in mechanical properties was attributed to the addition of higher hardness of HEB phase, crack deflection toughening mechanism, and presence of residual stress due to the mismatch of coefficient of thermal expansion.     

Synthesis of single-phase high-entropy diboride powders and their spheroidization process

Spherical (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ powders with a uniform particle size distribution are successfully prepared using a novel industrial approach, which combines spray-drying process and thermal plasma sintering technology together. In this, single-phase (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ powders are first synthesized via a borothermal reduction process using a mixture of individual metallic oxides and boron powders as starting materials. The influence of boron powder content on the structure of prepared powders is researched. Then, (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ granules are prepared after wet-grinding and spray-drying process, which exhibit a spherical shape and homogeneous element distribution. RF induction thermal plasma is finally used to sinter the granulated particle, and the apparent density of sintered spherical powders is increased to 2.57 g/cm³ from 1.43 g/cm³. Such powders are in potential demand for additive manufacturing techniques, and the successful synthesis of spherical (Zr_.2Ti_.2Ta_.2Nb_.2Mo_.2)B₂ powders may guide the way toward the preparation of many other spherical high-entropy diboride powders.     

(Hf0.2Zr0.2Ta0.2Nb0.2Ti0.2)C high‐entropy ceramics with low thermal conductivity

A novel high‐entropy carbide ceramic, (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C, with a single‐phase rock salt structure, was synthesized by spark plasma sintering. X‐ray diffraction confirmed the formation of a single‐phase rock salt structure at 26‐1140°C in Argon atmosphere, in which the 5 metal elements may share a cation position while the C element occupies the anion position. (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C exhibits a much lower thermal diffusivity and conductivity than the binary carbides HfC, ZrC, TaC, and TiC, which may result from the significant phonon scattering at its distorted anion sublattice. (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C inherits the high elastic modulus and hardness of the binary carbide ceramics.     

High entropy carbide ceramics from different starting materials

Three typical ceramic processing were respectively used to synthesize (Ti_0.2Zr_0.2Nb_0.2Ta_0.2W_0.2)C high-entropy carbide (HEC) ceramics by spark plasma sintering. Although single-phase composition characterized by X-ray diffraction were obtained by the three processes, the microstructures and elemental distributions are different. The reasons for the formation of these features are preliminarily discussed. The results demonstrate that the particle sizes of the starting metallic powders was a key factor for obtaining a homogeneous distribution of each elements in the HEC. Carbide process with relatively finer starting carbide powders compared to the above metallic starting powders resulted in an HEC with homogeneous distribution of elements, but the obtained ceramics showed the lowest relative density. For oxide process, it is considered that the obviously higher reaction temperature between ZrO₂ and graphite resulted in a two-phase structure of an HEC and a zirconium-rich phase, but the obtained HEC showed the highest relative density.     

Pressureless sintering and properties of (Hf0.2Zr0.2Ta0.2Nb0.2Ti0.2)C high-entropy ceramics: The effect of pyrolytic carbon

A novel (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C high-entropy ceramic was successfully prepared by pressureless sintering at 2200 °C. With increasing content of resin-derived-carbon, the density, and mechanical and thermal properties increased up to a maximum content of 2～4 wt% resin addition, after which further addition was detrimental. All specimens showed high strength (≥347±36 MPa), with the highest value achieving 450±64 MPa, and fracture toughness significantly higher (>20 %) than those of the corresponding monocarbides and Ta_0.5Hf_0.5C, (Ta_1/3Zr_1/3Nb_1/3)C. The thermal conductivity was approximately equivalent to the lowest value of the corresponding mono-carbides, which was assumed to be due to the lattice distortion effect.     

Thermophysical and mechanical properties of novel high-entropy metal nitride-carbides

In this work, a novel (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)(N_0.5C_0.5) high-entropy nitride-carbide (HENC-1) with multi-cationic and -anionic sublattice structure was reported and their thermophysical and mechanical properties were studied for the first time. The results of the first-principles calculations showed that HENC-1 had the highest mixing entropy of 1.151R, which resulted in the lowest Gibbs free energy above 600 K among HENC-1, (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)N high-entropy nitrides (HEN-1), and (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C high-entropy carbides (HEC-1). In this case, HENC-1 samples were successfully fabricated by hot-pressing sintering technique at the lowest temperature (1773 K) among HENC-1, HEN-1 and HEC-1 samples. The as-fabricated HENC-1 samples showed a single rock-salt structure of metal nitride-carbides and high compositional uniformity. Meanwhile, they exhibited high microhardness of 19.5 ± 0.3 GPa at an applied load of 9.8 N and nanohardness of 33.4 ± 0.5 GPa and simultaneously possessed a high bulk modulus of 258 GPa, Young's modulus of 429 GPa, shear modulus of 176 GPa, and elastic modulus of 572 ± 7 GPa. Their hardness and modulus are the highest among HENC-1, HEN-1 and HEC-1 samples, which could be attributed to the presence of mass disorder and lattice distortion from the multi-anionic sublattice structure and small grain in HENC-1 samples. In addition, the thermal conductivity of HENC-1 samples was significantly lower than the average value from the “rule of mixture” between HEC-1 and HEN-1 samples in the range of 300-800 K, which was due to the presence of lattice distortion from the multi-anionic sublattice structure in HENC-1 samples.     

Ablation behavior of high-entropy carbides ceramics (Hf0.2Zr0.2Ta0.2Nb0.2Ti0.2)C upon exposition to an oxyacetylene torch at 2000 °C

The ablation performance of a high-entropy ceramic carbide, (Hf_0.2Zr_0.2Ta_0.2Nb_0.2Ti_0.2)C, was performed by oxyacetylene ablation flame, simulating the extreme service environment at 2000 ºC. Phase and microstructure characterization at multi-length scales was carried out. During ablation, a compositionally and microstructurally complex oxidation layer formed on the ablation surface, which consisted of a combination of (Zr_xHf_1?x)₆(Nb_yTa_1?y)₂O₁₇, Ti(Nb_xTa_1?x)₂O₇, and Ti_x(Zr_aHf_bNb_cTa_1?a-b-c)_1?xO₂. Based on the microstructure information, the ablation mechanisms were proposed considering the oxidation thermodynamics and kinetics. Comparable rates of O inward diffusion and Ti outward diffusion are suggested, and a particular innermost dense layer composed of isolated (Zr_xHf_1?x)₆(Nb_yTa_1?y)₂O₁₇ grains embedded in a continuous Ti(Nb_xTa_1?x)₂O₇ matrix is considered to be beneficial for a better ablation resistance.     

High-entropy carbide ceramics with refined microstructure and enhanced thermal conductivity by the addition of graphite

Aiming at the refined microstructure and enhanced thermal conductivity of high-entropy carbide (HEC) ceramics for high-temperature applications, the addition effect of graphite was comprehensively investigated in this study. HEC ceramics incorporated with different contents of graphite were solidified by spark plasma sintering (SPS) using self-synthesized high-entropy (Ti_0.2Zr_0.2Hf_0.2Nb_0.2Ta_0.2)C powder and graphite as starting materials. The results demonstrate that the incorporated graphite removed the oxygen impurity in the mixed powders, decreased the oxygen content and increased the lattice parameter of the HEC phase, and improved the densification behavior of HEC ceramics. On the other hand, the addition of graphite brings a refinement of HEC grains and improves the mechanical properties. More importantly, the thermal conductivity of the HEC ceramics was significantly increased owing to the removing effect of oxide impurity by the added graphite. It is considered that the lattice "purified" HEC grains with low oxygen content contribute to the improvement in thermal conductivity of the ceramics.