Properties regulation of SiC ceramics prepared via stereolithography combined with reactive melt infiltration techniques

Stereolithography(SLA) combined with reactive melt infiltration (RMI) is an effective way to fabricate silicon carbide(SiC) ceramic components with complex shapes and high precision. The purpose of this paper is to increase the content of SiC in the sintered body and improve the properties of SiC ceramics prepared by SLA/RMI technologies by the impregnation of the precursor of carbon source after debinding. The effects of the concentration of phenolic resin solution on the strength of sintered body were studied. The results show that this method can reduce the coefficient of thermal expansion and improve the thermal conductivity of the final body. At the same time, when the concentration of phenolic resin solution is 40 wt%, the final body obtained the best comprehensive properties. The value of bulk density, flexural strength and elastic modulus were 2.89 g/cm³, 244.17 ± 5.13 MPa and 402.39 GPa, respectively. This strategy provides a promising prospect for the preparation of space optical mirrors with complex shapes and high strength by the SLA/RMI method.     

Laser additive manufacturing and homogeneous densification of complicated shape SiC ceramic parts

To improve the density of SiC ceramic components with complicated shape built by laser sintering (LS), cold isostatic pressing (CIP) and reaction sintering (RS) were incorporated into the process. In the process of LS/CIP/RS, Phenol formaldehyde resin (PF)-SiC composite powder was prepared by mechanical mixing and cold coating methods, with an optimized content of PF at 18?wt%. For the purpose of obtaining improved density of the sintered body after final reaction sintering, carbon black was added into the initial mixed powder. The material preparation, LS forming and densification steps were optimized throughout the whole fabrication process. The final sintered SiC bodies with the bending strength of 292 ~ 348?MPa and the density of 2.94–2.98?g?cm^{? 3} were prepared using the PF coated SiC-C composite powder and the LS / CIP / RS process. The study further showed a positive and practical approach to fabricate SiC ceramic parts with complicated shape using additive manufacturing technology.     

Effect of monomers content in enhancing solid-state densification of silicon carbide ceramics by aqueous gelcasting and pressureless sintering

The possibility of obtaining solid-state sintered silicon carbide (SiC) through aqueous gelcasting using commercial SiC powders was demonstrated. Green bodies were prepared from thixotropic SiC slurries in aqueous medium with optimized pH and solid-loading. The monomer system in gelcasting provides strength to the green bodies through formation of a gel network by polymerization and the carbon from polymeric gel enhances the densification of SiC, thereby avoiding addition of carbon externally to the gelcasting batches. Maximum bulk density of 3.16 g/cm³ (98.4% of relative density) was achieved in gelcast SiC on sintering at 2150 °C in argon atmosphere. The effect of carbon on SiC densification is evinced from the changes in microstructure of sintered SiC with increase in carbon content. The density and microstructure of gelcast and sintered SiC was comparable to that obtained from dry pressing and sintering of additive mixed SiC powders.     

Low thermal conductivity in porous SiC–SiO2–Al2O3–TiO2 ceramics induced by multiphase thermal resistance

The introduction of multiple heterogeneous interfaces in a ceramic is an efficient way to increase its thermal resistance. Novel porous SiC–SiO₂–Al₂O₃–TiO₂ (SSAT) ceramics were fabricated to achieve multiple heterogeneous interfaces by sintering equal volumes of SiC, SiO₂, Al₂O₃, and TiO₂ compacted powders with polysiloxane as a bonding phase and carbon as a template at 600 °C in air. The porosity could be controlled between 66% and 74% by adjusting the amounts of polysiloxane and the carbon template. The lowest thermal conductivity (0.059 W/(m·K) at 74% porosity) obtained in this study is an order of magnitude lower than those (0.2–1.3 W/(m·K)) of porous monolithic SiC, SiO₂, Al₂O₃, and TiO₂ ceramics at an equivalent porosity. The typical specific compressive strength value of the porous SSAT ceramics at 74% porosity was 3.2 MPa cm³/g.     

Microstructure and properties of needle punching chopped carbon fiber reinforced carbon and silicon carbide dual matrix composite

Chopped carbon fiber preform reinforced carbon and SiC dual matrix composites (C/C–SiC) were fabricated by chemical vapor infiltration (CVI) combined with liquid silicon infiltration. The preform was fabricated by repeatedly overlapping chopped carbon fiber web and needle punching technique. A geometry model of the pore structure of the preform was built and reactant gas transportation during the CVI was calculated. The microstructure and properties of the C/C–SiC composites were investigated. The results indicated that the CVI time for densification of the preform decrease sharply, and the model showed the permeability of the preform decreased with the increase of its density. The C/C–SiC exhibited good mechanical characteristics, especially excellent compressive behavior, with the vertical and parallel compressive strength reached to 359(±40) MPa and 257(±35) MPa, respectively. The coefficient of friction (COF) decreased from 0.60 (at 8 m/s) with the increase of sliding velocity, and finally stabilized at ~0.35 under the velocity of 20 m/s and 24 m/s, and the variations of COF were not sensitive to the sliding distance. The wear rates were between 0.012 cm³/MJ and 0.024 cm³/MJ under different velocities. These results showed that the chopped carbon fiber preform reinforced C/C–SiC are promising candidates for high-performance and low-cost friction composites.     

Electrically conductive SiC ceramics processed by pressureless sintering

Polycrystalline SiC ceramics with 10 vol% Y₂O₃-AlN additives were sintered without any applied pressure at temperatures of 1900-2050°C in nitrogen. The electrical resistivity of the resulting SiC ceramics decreased from 6.5 × 10¹ to 1.9 × 10⁻² Ω·cm as the sintering temperature increased from 1900 to 2050°C. The average grain size increased from 0.68 to 2.34 μm with increase in sintering temperature. A decrease in the electrical resistivity with increasing sintering temperature was attributed to the grain-growth-induced N-doping in the SiC grains, which is supported by the enhanced carrier density. The electrical conductivity of the SiC ceramic sintered at 2050°C was ~53 Ω⁻¹·cm⁻¹ at room temperature. This ceramic achieved the highest electrical conductivity among pressureless liquid-phase sintered SiC ceramics.     

Sinterability,microstructure and compressive strength of porous glass-ceramics from metallurgical silicon slag and waste glass

Porous glass-ceramics have been prepared by the direct sintering of powder mixtures of metallurgical silicon slag and waste glass. The thermal behavior of silicon slag was examined by differential thermal analysis and thermogravimetry to clarify the foaming mechanism of porous glass-ceramics. The mass loss of silicon slag below 700 °C was attributed to the oxidation of amorphous carbon from residual metallurgical coke in the silicon slag, and the mass gain above 800 °C to the passive oxidation of silicon carbide. The porosity of sintered glass-ceramics was characterized in terms of the apparent density and pore size. By simply adjusting the content of waste glass and sintering parameters (i.e. temperature, time and heating rate), the apparent density changed from 0.4 g/cm³ to 0.5 g/cm³, and the pore size from 0.7 mm to 1.4 mm. In addition to the existing crystalline phases in the silicon slag, the gehlenite phase appeared in the sintered glass-ceramics. The compressive strength of porous glass-ceramics firstly increased and then decreased with the sintering temperature, reaching a maximal value of 1.8 MPa at 750 °C. The mechanical strength was primarily influenced by the crystallinity of glass-ceramics and the interfaces between the crystalline phases and the glassy matrix. These sintered porous glass-ceramics exhibit superior properties such as light-weight, heat-insulation and sound-absorption, and could found their potential applications in the construction decoration.     

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Complex silicon carbide (SiC) ceramic components are difficult to fabricate due to their strong covalent bonds. Binder jetting (BJ) additive manufacturing has the outstanding advantages of high forming efficiency and no thermal deformation, especially suitable for printing complex structure SiC components. This study tried to obtain low silicon content silicon carbide ceramics by binder jetting followed by phenolic resin impregnation and pyrolysis (PRIP) and liquid silicon infiltration (LSI). BJ was used for the SiC green parts fabrication, and the highest compressive strength (7.7 ± 0.3 MPa) and lowest dimensional deviations (1.2–1.6 mm) were obtained with the printing layer thickness of 0.15 mm. Subsequently, PRIP treatments were introduced to increase the carbon content for the following LSI process. As the number of PRIP cycles increased, the carbon density of SiC/C preform increased and the porosity decreased. After the LSI treatment, the final Si-SiC composites processed with 2 PIRP cycles reached the highest flexural strength (257 ± 14.26 MPa) and the best wear resistance. This was attributed to the low residual silicon content (10.2 vol%) and almost no residual carbon. Furthermore, several complex structural components were fabricated using these methods. The preparation of complex components verifies the feasibility of BJ and LSI for manufacturing high-strength and high-precision SiC ceramics. Besides, this work hopes to provide technical guidance for the preparation of complex SiC composites in the future.     

Effect of Si addition on the mechanical and thermal properties of sintered reaction bonded silicon nitride

Advanced silicon nitride (Si₃N₄) ceramics were fabricated using a mixture of Si₃N₄ and silicon (Si) powders via conventional processing and sintering method. These Si₃N₄ ceramics with sintering additives of ZrO₂ + Gd₂O₃ + MgO were sintered at 1800 °C and 0.1 MPa in N₂ atmosphere for 2 h. The effects of added Si content on density, phases, microstructure, flexural strength, and thermal conductivity of the sintered Si₃N₄ samples were investigated in this study. The results showed that with the increase of Si content added, the density of the samples decreased from 3.39 g/cm³ to 2.92 g/cm³ except for the sample without initial Si₃N₄ powder addition, while the thermal diffusivity of the samples decreased slightly. This study suggested that addition of Si powder, which varied from 0 to 100%, in the starting materials might provide a promising route to fabricate cost-effective Si₃N₄ ceramics with a good combination of mechanical and thermal properties.     

Microstructure and mechanical properties of carbon-precursor-added B4C and B4C−SiC ceramics subjected to pressureless sintering

Organic-carbon-precursor-added B₄C and B₄C–SiC ceramics were subjected to pressureless sintering at various temperatures. The carbon precursor increased the densification of the B₄C and B₄C–SiC ceramics sintered at 2200 °C to 95.6 % and 99.1 % theoretical density (T.D.), respectively. The pyrolytic carbon content of the B₄C–SiC composite decreased with increasing SiC content. The graphitization degree of pyrolytic carbon decreased slightly with the amount of carbon precursor and content of SiC. The 95 wt. % B₄C–5 wt. % SiC composite added with 7.5 wt. % carbon precursor and sintered at 2200 °C outperformed the other B₄C–SiC composites, and its sintered density, flexural strength, Young’s modulus, and microhardness were 98.6 % T.D., 879 MPa, 415 GPa, and 28.5 GPa, respectively. These values were higher than those of composites prepared via pressureless sintering and comparable to those of composites fabricated via hot pressing and/or using metal or oxide additives.     

Effect of zirconia content and particle size on the properties of 3D-printed alumina-based ceramic cores

Alumina-based ceramic cores are used to manufacture the internal structures of hollow alloy blades, requiring both high precision and moderate properties. In this work, zirconia is regarded as a promoter to improve the mechanical properties of sintered ceramic. The effect of zirconia content and particle size on the microstructure and mechanical properties of ceramics was evaluated. The results indicate that the flexural strength of sintered ceramics reached the maximum of 14.5 ± 0.5 MPa when 20 wt% micron-sized (10 μm) zirconia (agglomerate size, consistent with the alumina particle size) was added, and 26.5±2.5 MPa when 15 wt% 0.3 μm zirconia was added. Zirconia with submicron-sized (0.3 μm) particles effectively filled the pores between alumina particles, thus leading to the maximum flexural strength with a relatively low content. The corresponding sintered ceramics had a bulk density of 2.0 g/cm³ and open porosity of 59.6%.     

Chemical conversion during transient liquid-phase hot pressing of TaSi2–TaC–SiC SHS-powder

This article presents a study on the manufacturing of three-phase TaSi₂–TaC–SiC ceramics through self-propagating high-temperature synthesis (SHS) and their subsequent chemical conversion to TaC–SiC carbide composites during transient liquid-phase hot pressing (HP). The effect of carbon black doping, ranging from 0% to 7%, on the degree of chemical conversion, structure, mechanical, and thermophysical properties of the ceramics was investigated. Our results showed that the proportionate increase of carbide content and decrease of TaSi₂ content in hot-pressed samples was achieved through carbon black doping. The increase of TaSi₂ content during hot pressing led to an increase in porosity from 4.3% to 23.8%, while the density decreased from 6.3 to 4.6 g/cm³. Superior mechanical properties were obtained when SHS-powder was doped with 1.5% carbon black (HV = 15.2 GPa, K_IC = 4.8 MPa × m^1/2, and σ_bend = 331 MPa). The structure of the ceramics was characterized by a TaSi₂–SiC matrix and highly dispersed TaC grains predominantly residing inside TaSi₂, with the TaC–TaSi₂ and TaSi₂–SiC interface being incoherent, as demonstrated through TEM studies. Complete conversion of TaSi₂ to TaC and SiC was achieved through 7% carbon black doping, resulting in the hot-pressed sample consisting solely of carbide grains. Two-stage hot pressing was employed to enhance the relative density of the two-phase TaC–SiC sample, resulting in ceramics characterized by HV up to 22.3 GPa, K_IC up to 6.1 MPa × m^1/2, σ_bend up to 256 MPa, and λ up to 36 W/(m × K).     

Effect of carbon nanoparticle reinforcement on mechanical and thermal properties of silicon carbide ceramics

This research presents an analysis of the influence of graphene reinforcement on the thermal and mechanical properties of silicon carbide ceramics, at 2.5% (wt%) graphene content. The SiC composites, containing various carbon nanofillers (graphene oxide and graphene nanoparticles), were sintered by the classical two stage spark plasma sintering method. Two current modes were used, the continuous mode and the pulsed current mode. The results from photothermal radiometry and investigations of the mechanical properties showed that graphene additives significantly improve the thermal properties and toughness of material, sintered from a SiC powder. An 45% growth in the toughness was observed, which increased from 1.21 to 1.75?MPa/m^1/2. The thermal diffusivity value also increased from 0.60 to 0.71?cm²/s and giving an improvement in thermal properties of 18%. The friction coefficient reached 7% giving an increase in value from 0.62 to 0.66. Microscopic investigations supported the photothermal radiometry (PTR) results. Whilst, thermal imaging revealed homogeneity of the local thermal properties of the products fabricated from the starting SiC powder.     

Biomorphic silicon/silicon carbide ceramics from birch powder

A novel process has been developed for the fabrication of biomorphic silicon/silicon carbide (Si/SiC) ceramics from birch powder. Fine birch powder was hot-pressed to obtain pre-templates, which were subsequently carbonized to acquire carbon templates, and these were then converted into biomorphic Si/SiC ceramics by liquid silicon infiltration at 1550 °C. The prepared ceramics are characterized by homogeneous microstructure, high density, and superior mechanical properties compared to biomorphic Si/SiC ceramics from birch blocks. Their maximum density has been measured as 3.01 g/cm³. The microstructure is similar to that of conventional reaction-bonded silicon carbide. The Vicker's hardness, flexural strength, elastic modulus, and fracture toughness of the biomorphic Si/SiC were 19.6 ± 2.2 GPa, 388 ± 36 MPa, 364 ± 22 GPa, and 3.5 ± 0.3 MPa m^1/2, respectively. The outstanding mechanical properties of the biomorphic Si/SiC ceramics are assessed to derive from the improved uniform microstructure of the pre-templates made from birch powder.     

Microstructure and properties of mullite–ZrO2 ceramics with silicon nitride additive prepared by spark plasma sintering

The process of densification and development of the microstructure of mullite–ZrO₂/Y₂O₃ ceramics from mixture of Al₂O₃, SiO₂, ZrO₂ and Y₂O₃ by gradually adding of α–β Si₃N₄ nanopowder from 1 to 5 wt% by traditional and spark plasma sintering were investigated by means of differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and some ceramic and mechanical properties. The processes of DTA for all samples are characterised by a low-pitched endo-effect, when gradual mullite formation and noticeable densification at temperatures of 1200–1400 °C is started. It is testified by shrinkage and density both for traditionally and by SPS-sintered samples. The influence of the Si₃N₄ additive on the density characteristics is insignificant for both sintering cases. For SPS samples, the density reaches up to 3.33 g/cm³, while for traditionally sintered samples, the value is 2.55 g/cm³, and the compressive strength for SPS grows with Si₃N₄ additives, reaching 600 N/mm². In the case of traditional sintering, it decreases to approximately 100 N/mm². The basic microstructure of ceramic samples sintered in a traditional way and by SPS is created from mullite (or pseudo-mullite) crystalline formations with the incorporation of ZrO₂ grains. The microstructure of ceramic samples sintered by SPS shows that mullite crystals are very densely arranged and they do not have the characteristic prismatic shape. The traditional sintering process causes the creation of voids in the microstructure, which, with an increasing amount of Si₃N₄ additive, are filled with mullite crystalline formations.     

Erosion behavior of SiC–WC composites

Dense silicon carbide (SiC) ceramics were prepared with 0, 10, 30 or 50 wt% WC particles by hot pressing powder mixtures of SiC, WC and oxide additives at 1800 °C for 1 h under a pressure of 40 MPa in an Ar atmosphere. Effects of alumina or SiC erodent particles and the WC content on the erosion performance of sintered SiC–WC composites were assessed. Microstructures of the sintered composites consisted of WC particles distributed in the equi-axed grain structure of SiC. Fracture surfaces showed a mixed mode of fracture, with a large extent of transgranular fracture observed in SiC ceramics prepared with 30 wt% WC. Crack bridging by WC enhanced toughening of the SiC ceramics. A maximum fracture toughness of 6.7 MPa*m^1/2 was observed for the SiC ceramics with 50 wt% WC, whereas a high hardness of 26 GPa was obtained for the SiC ceramics with 30 wt% WC. When eroded at normal incidence, two orders of magnitude less erosion occurred when SiC–WC composites were eroded by alumina particles than that eroded by SiC particles. The erosion rate of the composites increased with increasing angle of SiC particle impingement from 30° to 90°, and decreased with WC reinforcement up to 30 wt%. A minimum erosion wear rate of 6.6 mm³/kg was obtained for SiC–30 wt% WC composites. Effects of mechanical properties and microstructure on erosion of the sintered SiC–WC composites are discussed, and the dominant wear mechanisms are also elucidated.     

Effect of solid loading and carbon additive on microstructure and mechanical properties of 3D-printed SiC ceramic

3D-printed SiC ceramics were prepared by direct ink writing and solid-phase sintering. The effects of sintering temperature, solid loading, and carbon additive on microstructures and mechanical properties of 3D-printed SiC parts were investigated. It was found that the sintering temperature affected the evolution of the microstructure and mechanical properties of the sintered SiC parts. A high solid loading promoted the densification and mechanical properties of the sintered SiC parts. However, the solid loading exceeded 40 vol.%, which decreased the density and mechanical properties of the samples. The carbon additives could improve the densification of the SiC parts and enhance their mechanical properties. When the sucrose content increased from 0 to 8 wt.%, the open porosity of the SiC part decreased from 26.12% to 3.15%, whereas the flexural strength increased 2.19 times. Using the optimized components and process parameters, the high-performance 3D-printed SiC parts were achieved.     

Cellular glass obtained from non-powder preforms by foaming with steam

Cellular glass, or foamed glass, has been obtained as a result of the heating (to 700–800 °C) of heavy and strong preforms formed due to the binding properties of the silicate additives. Durability of the preforms reached 6 MPa at the density of 1.8 g/cm³. The main expanding agent in the composition is steam, which can also be a carbon oxidizer and increase the amount of the evolved gases and decrease the density of the foamed glass obtained. As a result of changing the initial composition structure, the density of the obtained foamed glass varied from 0.14 to 0.6 g/cm³, its breaking strength - from 0.6 to 5.0 MPa. and heat conductivity – from 0.045 to 0.15 W/(m·К), respectively. The speed of expansion of the preforms had an extreme character with the induction period typical for topochemical reactions. The obtained cellular materials possessed a distinct crystalline structure. The experiments showed the possibility of obtaining cellular materials with acceptable properties from different types of glass for the solution of environmental tasks. Various technological methods of obtaining cellular material blocks from preforms of various forms were tested to use them for thermal insulation and facing materials.     

Fabrication of porous silicon carbide ceramics with high porosity and high strength

Unique porous SiC ceramics with a honeycomb structure were fabricated by a sintering-decarburization process. In this new process, first a SiC ceramic bonded carbon (SiC/CBC) is sintered in vacuum by spark plasma sintering, and then carbon particles in SiC/CBC are volatized by heating in air at 1000 °C without shrinkage. The honeycomb structure has at least two different sizes of pores; ∼20 μm in size resulting from carbon removal; and smaller open pores of 2.1 μm remaining in the sintered SiC shell. The total porosity is around 70% and the bulk density is 0.93 mg/m³. The bending and compressive strengths are 26 MPa, and 105 MPa, respectively.     

Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology

A novel method has been developed to fabricate carbon fiber reinforced SiC (C_f/SiC) composites by combining 3D printing and liquid silicon infiltration process. Green parts are firstly fabricated through 3D printing from a starting phenolic resin coated carbon fiber composite powder; then the green parts are subjected to vacuum resin infiltration and pyrolysis successively to generate carbon fiber/carbon (C_f/C) preforms; finally, the C_f/C preforms are infiltrated with liquid silicon to obtain C_f/SiC composites. The 3D printing processing parameters show significant effects on the physical properties of the green parts and also the resultant C_f/C preforms, consequently greatly affecting the microstructures and mechanical performances of the final C_f/SiC composites. The overall linear shrinkage of the C_f/SiC composites is less than 3%, and the maximum density, flexural strength and fracture toughness are 2.83?±?0.03?g/cm³, 249?±?17.0?MPa and 3.48?±?0.24?MPa m^1/2, respectively. It demonstrates the capability of making near net-shape C_f/SiC composite parts with complex structures.