Thermochemical expansion of mixed-conducting (Ba,Sr)Co0.8Fe0.2O3−δ ceramics

The thermal and chemical expansion of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ (BSCF) and SrCo_0.8Fe_0.2O_3−δ (SCF) mixed ionic-electronic conductors were studied in combination with oxygen nonstoichiometry (δ) at 298–1223 K and p(O₂) = 10⁻⁴ to 1.00 atm. In order to minimize the effects of phase separation or oxygen-vacancy ordering processes, the data were collected in dynamic cooling mode using dense ceramic samples. The procedure was justified by a very fast equilibration at given p(O₂) in high-temperature range demonstrated for ceramics samples with different specific surface area. The difference in nonstoichiometry of BSCF and SCF at temperatures ≥973 K was found to be ≤0.03 oxygen atoms per formula unit. BSCF demonstrates favorably smaller chemical expansion compared to SCF and many other mixed conductors, originating from smaller δ variations and larger unit cell less sensitive to temperature and nonstoichiometry changes. Excessive thermochemical expansion impedes however the use of BSCF in single-phase fuel cell cathodes and planar mixed-conducting membranes.     

Microstructural comparison of porous oxide ceramics from the system Al2O3–ZrO2 prepared with starch as a pore-forming agent

In this paper we show examples of microstructures of porous oxide ceramics prepared by traditional slip casting (TSC) and starch consolidation casting (SCC) and present results obtained using different microstructural characterization techniques; Archimedes method (open and total porosity), shrinkage measurement, mercury intrusion porosimetry (pore size distribution) and microscopic methods – optical microscopy with microscopic image analysis (pore size distribution) and scanning electron microscopy (detailed investigation of the local microstructure). In particular, microstructures are compared for porous ceramics from the system Al₂O₃–ZrO₂ prepared with rice and corn starch. It is shown that maximum values of the total porosity of porous ceramics prepared with starch as a pore-forming agent were approx. 50%. A major finding by using SEM with respect to starch-produced porous ceramics is the existence of pore fillings in the form of small sintered ceramic shell inside the pores, as a result of starch granule shrinkage during the drying and burn-out steps.     

Electrochemical and microstructural characteristics of nanoperovskite oxides Ba0.2Sr0.8Co0.8Fe0.2O3−δ (BSCF) for solid oxide fuel cells

Nanoperovskite oxides, Ba_0.2Sr_0.8Co_0.8Fe_0.2O_3?δ (BSCF), were synthesized via the co-precipitation method using Ba, Sr, Co, and Fe nitrates as precursors. Next, half cells were fabricated by painting BSCF thin film on Sm_0.2Ce_0.8O_x (samarium doped ceria, SDC) electrolyte pellets. X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and electrochemical impedance spectroscopy (EIS) measurements were carried out on the BSCF powders and pellets obtained after sintering at 900 °C. Investigations revealed that single-phase perovskites with cubic structure was obtained in this study. The impedance spectra for BSCF/SDC/BSCF cells were measured to obtain the interfacial area specific resistances (ASR) at several operating temperatures. The lowest values of ASR were found to be 0.19 Ω cm², 0.14 Ω cm² 0.10 cm², 0.09 Ω cm² and 0.07 Ω cm² at operating temperatures of 600 °C, 650 °C, 700 °C, 750 °C and 800 °C, respectively. The highest conductivity was found for cells sintered at 900 °C with an electrical conductivity of 153 S cm^?1 in air at operating temperature of 700 °C.     

Experimental investigation and mathematical modeling of oxygen permeation through dense Ba0.5Sr0.5Co0.8Fe0.2O3−δ (BSCF) perovskite-type ceramic membranes

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3?δ (BSCF) perovskite powder was synthesized via EDTA/citrate complexation method. BSCF membranes were formed by pressing powder at 400 MPa and sintering at 1100 °C for 10 h. XRD patterns showed that a high pure powder with cubic structure was obtained. SEM micrographs revealed that the membranes are dense with large grains. Effects of temperature, feed and permeate side oxygen partial pressures, flow rates and membrane thickness on oxygen permeation flux were studied experimentally. A Nernst–Planck based mathematical model, including surface exchange kinetics and bulk diffusion, was developed to predict oxygen permeation flux. Considering non-elementary surface reactions and introducing system hydrodynamics into the model resulted in an excellent agreement (RMSD = 0.0617, AAD = 0.0487 and R² = 0.985) between predicted and measured fluxes. The results showed that oxygen permeation flux increases with temperature, feed side oxygen partial pressure and flow rates, however decreases with permeate side oxygen partial pressure and membrane thickness. Contribution of feed side surface exchange reactions, bulk diffusion and permeate side surface exchange reactions resistances in the total resistance are in the range of 8–32%, 10–81% and 11–59%, respectively. Permeation rate-limiting step was determined using the membrane dimensionless characteristic thickness.     

Thermal and chemical induced expansion of La0.3Sr0.7(Fe,Ga)O3−δ ceramics

The linear thermal expansion coefficients (TECs) of perovskite-type La_0.3Sr_0.7Fe_1−xGa_xO_3−δ (x=0–0.4), determined by dilatometric and high-temperature X-ray diffraction techniques, are in the range (19–41)×10⁻⁶ K⁻¹ at 770–1170 K, decreasing when the oxygen partial pressure or gallium concentration increases. At oxygen pressures from 10⁻⁴ to 1 atm, the isothermal chemically induced expansion of La_0.3Sr_0.7Fe(Ga)O_3−δ ceramics is a linear function of the oxygen nonstoichiometry. The magnitude of changes in δ and, thus, chemical expansion both are reduced by gallium doping. The ratio between isothermal chemical strain and nonstoichiometry variations, (ε_C/Δδ), follows an Arrhenius-type dependence on temperature and varies in the range (1.7–5.9)×10⁻². The drastic increase in the thermal expansion at temperatures above 700 K, typical for ferrite-based ceramics, was shown to be mainly apparent, resulting from the chemically-induced expansion of the lattice due to oxygen losses. The TEC values, corrected for the chemical strain on heating, are close to the TECs at low temperatures and increase with gallium content. The observed correlations between the thermal and chemical expansion and ionic conductivity of La_0.3Sr_0.7Fe_1−xGa_xO_3−δ are discussed in terms of their relationships with the oxygen deficiency and cation composition.     

Effect of microstructure on oxygen permeation of Ba0.5Sr0.5Co0.8Fe0.2O3−δ and SrCo0.8Fe0.2O3−δ membranes

The effect of grain size on oxygen permeation properties of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3?δ (BSCF) and SrCo_0.8Fe_0.2O_3?δ (SCF) membranes was investigated by variation of the dwell time. The membrane microstructure was examined by field-emission scanning microscopy (FE-SEM) and then evaluated using a statistical approach. With longer dwell times the grain growth was stimulated and leaded to grains with a narrower size distribution. The grains of SCF (average size from 11.3 to 19.9 μm) were found to be smaller than those of BSCF (average size from 13.9 to 41.3 μm). The oxygen permeation flux of BSCF membranes was found to be independent of grain size in the range from 24 to 42 μm. However, membranes with smaller grains (13.9 μm) show a decreased oxygen permeation flux. For the SCF membranes a decrease in permeation flux with larger grains was observed for average grain sizes between 11.3 and 19.9 μm. By transmission electron microscopy (TEM) formation of an oxygen ordered SrCo_0.8Fe_0.2O_2.5 brownmillerite by-phase could be observed at the oxygen-depleted sweep side of the membrane.     

Preparation and pore-forming mechanism of MgO–Al2O3–CaO-based porous ceramics using phosphorus tailings

A simple strategy for preparing MgO–Al₂O₃–CaO-based porous ceramics (MACPC) with high strength and ultralow thermal conductivity has been proposed in this work based on the raw material of phosphorus tailings. The effects of phosphorus tailings content, carbon black addition and heat treatment temperature on the properties of MACPC were studied, and their pore-forming mechanism during sintering was revealed. The results showed that the main phase composition of MACPC was magnesia alumina spinel and calcium aluminate after sintering at 1225 °C. Furthermore, the MACPC exhibited excellent comprehensive properties when 60 wt% phosphorus tailings and 40 wt% alumina were added, whose apparent porosity was 62.8%, cold compressive strength was 14.8 MPa, and the thermal conductivity was 0.106 W/(m·K) at 800 °C. The synchronously enhanced strength and thermal insulation properties of MACPC were related to the formation of uniformly distributed micropores (<2 μm) and passages in the matrix, which originated from the decomposition of phosphorus tailings and the burnt out of carbon black during the sintering process. The preparation of MACPC with high temperature resistance and excellent mechanical and thermal insulation properties with the raw material of phosphorus tailings provided an effective method for the high-value utilization of phosphorus tailings.     

Structural and superconducting properties of Y(Ba1-xKx)2Cu3O7-δ ceramics

Y(Ba_1-xK_x)₂Cu₃O_7-δ ceramics (x = 0.00, 0.03, 0.05 and 0.08) were synthesized by thermal treatments of aqueous solution of metals nitrates and polyvinyl pyrrolidone (PVP) that acts as a capping agent. The effects of K-substitution on the crystal structure, microstructure and electrical resistance of samples were investigated. The X-ray diffractions results indicated an improvement of crystallinity and variation of lattice constant, a, b and c of YBa₂Cu₃O_7-δ (Y123) phase with K-substitution. The K-substitution resulted in increasing of orthorhombicity factor compared to pure Y123. Microstructural observation using scanning electron microscopy showed that K-substitution promotes the grain growth of Y123. The superconducting transitions (T_c) of the substituted-samples were higher than that of the pure Y123. The T_c (onset) were 93, 97, 95, 95 K for the samples with x = 0.00, 0.03, 0.05 and 0.08, respectively. Comparing with pure sample, the substituted-samples showed sharper superconducting transition (ΔT_c). The best superconducting properties was observed for sample with x = 0.03.     

Recycling bagasse and rice hulls ash as a pore-forming agent in the fabrication of cordierite–spinel porous ceramics

Bagasse and rice hulls ash are both waste materials. In recent years, in order to meet environmental protection, these materials have been recycled in the production of porous ceramics. A solid-state reaction mechanism of calcined alumina and talc was used to prepare cordierite–spinel porous ceramics. Talc was added from 30 to 60 wt.% at the expense of alumina and sintered at 1400°C for 2 h. The effect of bagasse and rice hulls ash (as a pore forming agent) on the densification parameters, cold crushing strength (CCS), and pore size distribution was also studied. The phase composition (X-ray diffraction) and microstructure (scanning electron microscopy) of sintered samples were investigated. The results showed that the main phases present in the samples are cordierite, corundum, spinel, and sapphirine. In the sample with a higher amount of talc additions (60 wt.%), only the formation of the cordierite and spinel phases was observed. The bulk density of the samples and the apparent porosity ranged from 1.77 to 2.26 g/cm³ and from 28.6% to 48.21%, respectively. The CCS of the samples ranges from 13.9 to 36.3 MPa. The microstructures of the sintered samples were observed for the formation of cordierite phase, alumina phase, and spinel phase in an excellent crystallization and phase arrangement.     

Creep behavior of porous La0.6Sr0.4Co0.2Fe0.8O3-δ substrate material for oxygen separation application

Advanced oxygen transport membrane designs consist of a thin functional layer supported by a porous substrate material that carries mechanical loads. Creep deformation behavior is to be assessed to warrant a long-term reliable operation at elevated temperatures. Aiming towards an asymmetric composite, the current study reports and compares the creep behavior of La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ (LSCF) perovskite porous substrate material with different porosity and pore structures in air for a temperature range of 800–1000?°C. A porosity and pore structure independent average stress exponent and activation energy are derived from the deformation data, both being representative for the LSCF material. To investigate the structural stability of the dense layer in an asymmetric membrane, sandwich samples of Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF) and La_0.6Sr_0.4Co_0.2Fe_0.8O_3-δ (LSCF) with porous substrate and dense layers on both side were tested by three-point bending with respect to creep rupture behavior of the dense layer. Creep rupture cracks were observed in the tensile surface of BSCF, but not in the case of LSCF.     

Oxygen permeation through dense La0.1Sr0.9Co0.8Fe0.2O3−δ perovskite membranes: Catalytic effect of porous La0.1Sr0.9Co0.8Fe0.2O3−δ layers

The oxygen permeation performance of a number of La_0.1Sr_0.9Co_0.8Fe_0.2O_3−δ (LSCF1982)-based membranes, consisting of dense LSCF1982 layer with/without porous LSCF1982 layer, was analyzed on the basis of the thickness of the dense layer and catalytic effect of the porous layer. A 0.27 mm thick dense membrane gives oxygen permeation flux ($J_{O_2}$) of 2.33 sccm min⁻¹ cm⁻² at 900 °C, which is increased to 3.55 sccm min⁻¹ cm⁻² on applying a porous layer of LSCF1982 onto the dense membrane. The membrane gives a stable flux for 300 h. The flux was further improved by reducing the thickness of the dense LSCF1982 layer and at 950 °C a flux of 4.47 sccm min⁻¹ cm⁻² is obtained with 0.012 mm thick membrane.     

Ammonia oxidation in Ba0.5Sr0.5Co0.8Fe0.2O3−δ membrane reactor

Selective oxidation of ammonia to NO was studied in a dense mixed ion electron conducting Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3?δ membrane reactor, which integrates the separation and catalytic reaction process in a single reactive separation unit. The influence of the temperature and feed concentration on the membrane reaction performance were investigated in detail. Under reaction conditions, the oxygen permeation flux through the dense membrane increases with increasing temperature and ammonia flow rate. The lower temperature and ammonia concentration can favor the formation of NO, in which higher catalytic performance is obtained, suggesting that the membrane reactor operation is much beneficial for selective oxidation of ammonia.     

Structural and mechanical properties of La0.6Sr0.4M0.1Fe0.9O3-δ (M: Co,Ni and Cu) perovskites

La_0.6Sr_0.4M_0.1Fe_0.9O_3-δ (M: Co, Ni and Cu) perovskite nanostructures were synthesized using low frequency ultrasound assisted synthesis technique and effect of substitution of Fe by Co, Ni and Cu on crystal structure and mechanical properties in La_0.6Sr_0.4FeO_3-δ perovskite was studied. The HRTEM and Rietveld refinement analyses revealed the uniform equi-axial shape of the obtained nanostructures with the existence of La_0.6Sr_0.4M_0.1Fe_0.9O_3−δ with mixed rhombohedral and orthorhombic structures. Substitution by Cu decreases the melting point of La_0.6Sr_0.4FeO_3-δ. The results of mechanical characterizations show that La_0.6Sr_0.4Co_0.1Fe_0.9O_3−δ and La_0.6Sr_0.4Ni_0.1Fe_0.9O_3−δ have ferroelastic behavior and comparable elastic moduli, however, substitution by Ni shows higher hardness and lower fracture toughness than Co in B-site doping.     

Modeling of U-shaped Ba0.5Sr0.5Co0.8Fe0.2O3-δ hollow-fiber membrane for oxygen permeation

A mathematic model is developed for the perovskite-type mixed ionic-electronic conducting (MIEC) membrane,which makes it possible to simulate the process of oxygen separation in the U-shaped Ba0.5Sr0.5Co0.8Fe0.2O3-δ hollow-fiber membrane.The model correlates the oxygen permeation flux to the measurable variables.The trends of calculated results for purge operation coincide well with the experimental data,therefore the model is considerable for flux prediction under vacuum operation.Higher oxygen separation efficiency can be achieved with vacuum operation than purge operation.Parameter study with vacuum operation reveals that oxygen permeation flux increases with higher vacuum levels,and vacuum pressure of around 1.013 × 103 Pa is the optimal.Also,vacuum operation on the lumen side is much more efficient to achieve higher oxygen permeation flux compared with compression mode on the shell side.     

Thermoelectric properties of ytterbium interstitial doped Sr0.7Ba0.3YbxNb2O6-δ ceramics

The thermoelectric properties of interstitial doped Sr_0.7Ba_0.3Yb_xNb₂O_6-δ ceramics were investigated in the temperature range from 323 K to 1073 K. The ytterbium interstitial doping contributes to increasing the power factor (PF) by improving the electrical conductivity. The PF values of Sr_0.7Ba_0.3Yb_0.1Nb₂O_6-δ are comparable to those of the substitution doped sample with twice the doping content. This can be ascribed to the large electronic charge of the dopants relative to the occupied site in the interstitial case. The lattice thermal conductivity of Sr_0.7Ba_0.3Yb_xNb₂O_6-δshows a glass-like behavior due to lattice disorder. The disorder degree deepens as the doping content increases, resulting in plateau values of the lattice thermal conductivity at high temperatures in the Sr_0.7Ba_0.3Yb_0.05Nb₂O_6-δ and Sr_0.7Ba_0.3Yb_0.1Nb₂O_6-δ samples.     

Fabrication and properties of porous mullite ceramics from calcined carbonaceous kaolin and α-Al2O3

High purity calcined carbonaceous kaolin and α-Al₂O₃ powders were employed to prepare porous mullite ceramics (Sample A) using graphite as pore former with the reaction sintering method. For the purpose of comparison, porous mullite ceramics (Sample B) was also fabricated from the uncalcined carbonaceous clay incorporated with α-Al₂O₃ powders. Mullitization in the two samples was both nearly complete at 1500 °C, despite the fact that calcination of the clay remarkably depressed mullitization and promoted the formation of glass phase. The Sample A sintered at 1500 °C fractured mainly in an intergranular way, while the Sample B mainly underwent transgranular fracture. The experimental results revealed that densification behavior/open porosity of the Sample A was far more sensitive to sintering temperature. The pore size of the Sample A as well as the Sample B sintered at 1500 °C was in a narrower range of 0.3–5 μm.     

Microstructure coarsening in Ba0.5Sr0.5Co0.8Fe0.2O3-δ during reactive air brazing

Reactive air brazing of the ceramic oxygen transport membrane material BSCF causes microstructural modifications. The trend towards minimizing of membrane thicknesses requires a physical understanding of these modifications since they may influence both oxygen permeation and mechanical properties. To this purpose, wetting samples with variations in the Ag-xCuO braze alloy (1 < x < 25 at.-%) and the brazing time (0 < t < 120 min) were characterized by quantitative image analysis. We found that the pore size in reactive air brazed BSCF increases with increased brazing time as well as CuO-content in the braze. A local porosity minimum is always observed at the end of the reaction zone close to the unaffected bulk BSCF. Additionally, a zone with unidirectionally elongated grains at the end of which silver residues were found is observed. The observed coarsening effects are explained by liquid melt film penetration along the grain boundaries which increases the grain boundary mobility. Phase field simulations qualitatively confirmed the experimentally observed elongated grain structure.     

Mechanical behavior of ferroelastic porous La0.6Sr0.4Co0.2Fe0.8O3−δ prepared with different pore formers

The present work investigated the mechanical behavior of porous La_0.6Sr_0.4Co_0.2 Fe_0.8O_3−δ LSCF under uniaxial compression. The porous (LSCF) samples with the same grain size but different porous structures with 1.5–41% of porosity were prepared using three different pore formers. All the samples had ferroelastic domains and exhibited ferroelastic mechanical behaviors under uniaxial compression. Initial and loading moduli as well as critical stress monotonically decreased and remnant strain increased with increasing the porosity. The initial modulus can be determined by the actual porosity regardless of porous structure or grain size, whereas the other properties were more sensitive to experimental condition such as loading rate and maximum applied stress. Compressive fracture strength could be significantly influenced by porous structure.     

A case study of mechanical properties of perovskite-structured Ba0.5Sr0.5Co0.8Fe0.2O3−δ oxygen transport membrane

This study has investigated mechanical properties of perovskite-structured Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF) oxygen transport membrane. The Young’s modulus and fracture toughness are determined by both macroscopic-scale and microscopic-scale methods. Both three-point and ring-on-ring bending tests as macroscopic-scale methods produce broadly similar results with a Young’s modulus, which is lower than that measured from micro-indentation method under a 10 N load. Young’s modulus and fracture toughness of BSCF show strongly dependent of the porosity. However, the fracture toughness of BSCF is independent of grain size. The fracture toughness determined by macroscopic-scale method is similar with that measured by microscopic-scale method. The crack shape of BSCF under a 10 N load is determined to be a median-radial mode. The intrinsic Young’s modulus and fracture toughness are determined to be 105.6 GPa and 1.49 MPa m^0.5, respectively, according the Minimum Solid Area (MSA) model. Annealing decreases the fracture toughness of BSCF between RT and 800 °C.     

Preparation and properties of porous SiC–Al2O3 ceramics using coal ash

In this paper, we first reported that porous SiC–Al₂O₃ ceramics were prepared from solid waste coal ash, activated carbon, and commercial SiC powder by a carbothermal reduction reaction (CRR) method under Ar atmosphere. The effects of addition amounts of SiC (0, 10, 15, and 20 wt%) on the postsintering properties of as-prepared porous SiC–Al₂O₃ ceramics, such as phase composition, microstructure, apparent porosity, bulk density, pore size distribution, compressive strength, thermal shock resistance, and thermal diffusivity have been investigated. It was found that the final products are β-SiC and α-Al₂O₃. Meanwhile, the SEM shows the pores distribute uniformly and the body gradually contacts closely in the porous SiC–Al₂O₃ ceramics. The properties of as-prepared porous SiC–Al₂O₃ ceramics were found to be remarkably improved by adding proper amounts of SiC (10, 15, and 20 wt%). However, further increasing the amount of SiC leads to a decrease in thermal shock resistance and mechanical properties. Porous SiC–Al₂O₃ ceramics doped with 10 wt% SiC and sintered at 1600°C for 5 hours with the median pore diameter of 4.24 μm, room-temperature compressive strength of 21.70 MPa, apparent porosity of 48%, and thermal diffusivity of 0.0194 cm²/s were successfully obtained.