Compact UWB bandpass filter with dual‐notch bands using asymmetric tri‐section stepped impedance resonator

In this study, a novel high selective UWB band pass filter (BPF) with dual notch band is presented. UWB BPF is realized using stub‐loaded multiple‐mode resonator (MMR). The MMR is constructed by loading a quintuple mode open stub at the centre in an asymmetric tri‐section stepped impedance resonator (ATSSIR). Five modes, including two odd modes and three even modes, placed within UWB band. Two transmission zeros generated by the fractal stub improve the passband selectivity greatly. Two half wavelength long fractal Hilbert resonators are embedded near I/O line to achieve notch bands at 5.1 and 5.9 GHz. Aperture‐backed interdigital coupled‐lines are implemented to improve the coupling. The proposed prototype is fabricated and tested. The measured insertion loss is observed to be within 1.5 dB over the passband. By virtue of two transmission zeros (TZs), on either side of the passband, at 5.1 and 5.9 GHz, respectively, the passband selectivity is achieved with measured roll‐off factor at around 34 dB/octave. The out‐of‐band rejection of the filter is greater than 22 dB up to 18 GHz. The simulated results are in good agreement with the measured responses.     

Design of wideband comb shape substrate integrated waveguide multimode resonator bandpass filter with high selectivity and improved upper stopband performance

In this article, a wideband bandpass filter (BPF) is designed using the comb slotted substrate integrated waveguide (SIW) cavities. The comb‐shaped slots engraved on the SIW cavity are used to constitute a novel multiple‐mode resonator (MMR) that accomplishes a wide passband of operation. Further, a Jerusalem cross defected ground structure (DGS) is introduced to miniaturize it and enhance filter performance in the pass band and stop band. The filter is fabricated on RT/Duroid 5880 having dielectric constant 2.2 and tested to prove the validity of design. The filter achieves 3 dB fractional bandwidth of 48%, return loss above 14 dB and insertion loss of 1.1 dB in the passband. Also, the proposed filter has steep selectivity and wide upper stopband with 25 dB attenuation from 16.7 to 24 GHz.     

Compact tri‐notched ultrawideband bandpass filter design using CSRR,DGS, and FMRR configurations

The folded multiple‐mode resonators with complementary split ring resonator (CSRR), and defected ground structures (DGS) are introduced for notched ultrawideband (UWB) bandpass filter (BPF) design in this article. Using the CSRR, FMRR, notched wide‐band BPF, a notch response can exist in the UWB passband for blocking the interference. Adjusting the size factor of CSRR, the wide tuning ranges of notch frequencies included the desired frequencies of 5.2/5.8 GHz are achieved. The lower insertion loss (0.31 dB), higher rejection level (?48.40 dB), wider bandwidth (FBW 75%), and wider stopband (extended to 2.01 f₀ below ?20 dB rejection level) of UWB band at the central frequency f₀ = 4.58 GHz are obtained. Second, design a CSRR, DGS, FMRR, tri‐notched UWB filter, the wider bandwidth (3.1–9.8 GHz) with FBW = 126%, lower insertion loss (0.26 dB), and higher rejection level (?44 dB) of UWB band at central frequency f₀ = 5.6 GHz are presented. Using the CSRR and interdigital couple, three notch responses can exist in the UWB passband for blocking the interference signals. Adjusting the size factor of CSRR and interdigital couple, the wide tuning ranges of notch frequencies included the desired frequencies of 5.18/6.10/8.08 GHz are achieved. The wide tuning ranges of three notched frequencies cover from 5.0 to 8.4 GHz. It is a simple way to control the notch responses. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:571–579, 2014.     

Design of UWB bandpass filter with dual notched bands

An ultra-wideband (UWB) bandpass filter (BPF) with dual sharply rejected notch-bands to elim-inate the interference from coexisting radio systems is presented in this paper.The characteristics of the proposed notched structure are investigated using simulations to demonstrate the design flexibility of the notch-band performance.After integrating the proposed notched structure into the basic UWB BPF based on a stepped-impedance stub loaded resonator (SISLR),a UWB BPF with dual sharply rejected notched bands at 5.2 and 5.8 GHz is constructed.Finally,the designed filter is built and tested.The simulated and measured results are found to be in good agreement to verify the proposed design.     

Inter‐digital coupled dual‐mode patch resonator with crossed‐island configuration for tri‐band filter design

The miniaturized dual‐mode tri‐band band‐pass filters (BPF) using crossed‐island patch resonator is proposed in this article. The BPF is mainly formed by a square patch resonator in which a crossed‐island configuration is embedded in the patch. The patch size reduction with 74.4% is achieved. By the perturbation and the alternative inter‐digital coupling, the tri‐band responses are obtained. The proposed filter covers the required bandwidths for WLAN band (2.26–3.11 GHz and 5.02–6.0 GHz) and X‐band (7.58–8.41 GHz) applications. Five transmission zeros are placed between three pass‐bands and resulted in a good isolation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:457–463, 2014.     

Perturbed Sierpinski carpet resonator and its usage in compact dual and triple band bandpass filters

In this paper, perturbed Sierpinski carpet fractal shaped resonator is characterized and applied in the design of multiband band pass filters (BPFs). The route to achieving compact multimode resonators starting from the Sierpinski carpet fractal shaped resonator is detailed. The proposed resonators are used to demonstrate two topologies of dual band bandpass filters with passband center frequencies at 3.5 GHz as well as 5.5 GHz, respectively. Both the designs exhibit nearly identical passband bandwidth. In the second design, it is observed that the second passband gets slightly shifted towards 5.85 GHz. However, with edge loading this shift is nullified. A scaled down version of the same resonator is designed and three such resonators are interdigitally coupled in conjunction with complementary split ring resonators to exhibit a novel technique of achieving compact triband bandpass filter. All designs have acceptable passband insertion loss in the respective bands. Accessories are used to improve passband selectivity in all designs and also a wide stop band till 10 GHz is obtained. Fabrication prototypes for all the variants are realized with simulated and measured results in good agreement. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:418–425, 2016.     

Band‐pass filter design using modified CSRR‐DGS

In this article, a novel compact band‐pass filter (BPF) with sharp cutoffs and a wide stop‐band is presented. The BPF is basically designed by cutting a modified complementary split‐ring resonator (CSRR) from the ground of two separated microstrip feed lines and has a 71% fractional bandwidth from 4.1 to 9 GHz. Because of the high insertion loss, the designed filter should be packed in a metallic cavity that has undesirable resonances in the stop‐band of the BPF. For eliminating cavity resonances, an evolutionary optimization technique based on changing the pixels of the CSRR defected ground structure is used. A prototype of the final structure obtained from the optimization technique is fabricated. The measurement results show that the optimized filter have a pass band from 4 to 8 GHz with a rejection better than 15 dB from 4 to 15 GHz. The designed filters have compact dimensions of 12 × 12 × 0.787 mm³. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:544–548, 2014.     

Multi‐mode resonators with quad‐/penta‐/sext‐mode resonant characteristics and their applications to bandpass filters

In this article, a new class of dual‐/tri‐band and ultra‐wideband (UWB) bandpass filters (BPFs) using novel multi‐mode resonators are proposed. The classical even‐/odd‐mode method is applied to analyze the resonant characteristics of the proposed resonators, which exhibit controllable resonant modes with different dimension parameters under the same configuration. According to the analysis, three resonators with quad‐/penta‐/sext‐mode resonant characteristics are obtained by choosing the specific dimension parameters. Then, the quad‐mode resonator is used to design a dual‐wideband BPF centred at 2.39/5.14 GHz with 3‐dB fractional bandwidths (FBWs) of 36.9%/18.9%, and the penta‐mode resonator is utilized to design an UWB BPF with 3‐dB FBW of 102.2%, whereas the sext‐mode resonator is applied to design a tri‐band BPF with centre frequencies of 2.09/3.52/5.46 GHz and 3‐dB FBWs of 11.3%/20%/12.1%. All these three filters are fabricated and measured, and the measured results are in good agreement with the simulated ones.     

Design of high selectivity tri‐band bandpass filter with wide upper stopband

This article presents a dual‐plane structure high selectivity tri‐band bandpass filter (BPF) which consists of a pair of T‐shaped microstrip feed lines with capacitive source‐load coupling as well as spur lines embedded, and three resonators, i.e., a dual‐mode stub‐loaded stepped impedance resonator and two nested dual‐mode defected ground structure resonators. Using the intrinsic characteristics of the resonators and feed lines, nine transmission zeros near the passband edges and in the stopband can be generated to achieve high selectivity. An experimental tri‐band BPF located at 2.4/5.7 GHz [wireless local area networks (WLAN) application] and 3.5 GHz [worldwide interoperability for microwave access (WiMAX) application] has been simulated and fabricated. Good agreement between the simulated and measured results validates the design approach. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Novel configuration of ultra‐wide band uni‐planar configuration of complementary split ring resonator composite right/left‐handed based band pass filter with sharp roll off and good stopband attenuation

In this paper, a compact novel simple design of ultra‐wide bandpass filter with high out of band attenuation is presented. The filter configuration is based on combining an ultra‐wide band composite right/left‐handed (CRLH) band pass filter (BPF) with simple uni‐planar configuration of complementary split ring resonator (UP‐CSRR). By integrating two UP‐CSRR cells, the ultra‐wideband CRLH filter roll‐off and wide stopband attenuation are enhanced. The filter has 3 dB cutoff frequencies at 3.1 GHz and 10.6 GHz with insertion loss equals 0.7 dB in average and minimum and maximum values of 0.48 dB and 1.05 dB, respectively over the filter passband. Within the passband. The transition band attenuation from 3 dB to 20 dB is achieved within the frequency band 1.9 GHz to 3.1 GHz (48%) at lower cutoff and the frequency band 10.6 GHz to 11.4 GHz (7%) at upper stopband. Moreover, the filter has a wide stopband attenuation >20 dB in frequencies 11 GHz to 13.6 GHz (21%) and ends with 3 dB cutoff frequency at 14.8 GHz. Furthermore, the designed filter size is very compact (23 × 12 mm²) whose length is only about 0.17 λ_g at 6.85 GHz. The filter performance is examined using circuit modeling, full‐wave simulations, and experimental measurements with good matching between all of them.     

Compact dual‐band bandpass filter and diplexer using hybrid resonant structure with independently controllable dual passbands

In this article, a compact dual‐band bandpass filter (BPF) is developed using a hybrid resonant structure, which consists of a microstrip stub‐loaded dual‐mode resonator and a slotline stub‐loaded dual‐mode resonator. These two resonators, both having two controllable resonant modes and one transmission zero (TZ), are analyzed and used to construct two desired passbands of a dual‐band BPF. Multiple TZs are generated by introducing a source‐load coupling, thus improving the selectivity of the passbands. Then, the dual‐band BPF is reshaped to configure a compact diplexer. The inherent TZs of the two proposed resonators are designed to improve the frequency property and port isolation of the diplexer. Finally, a dual‐band BPF and a diplexer with the lower and upper passbands centered at 2.45 and 3.45 GHz, respectively, are designed, fabricated, and measured to verify the proposed structure and method.     

A compact UWB bandpass filter with a notched band using a multistubs loaded resonator

A novel multistubs loaded resonator (MSLR) is proposed in this article, which is constructed by several open‐ and short‐circuited stubs. The analysis shows that it is characterized by four resonant modes. Then, the MSLR is applied in the design of a compact ultra‐wideband (UWB) bandpass filter. The measured results show that its 3dB bandwidth can cover [3.0, 11.5] GHz, that is, 3 dB fractional bandwidth is 117%, and the return loss within the passband is greater than 15 dB. Especially, the roll‐off rate is higher than 33 dB/GHz and more than 40 dB harmonic suppression can be achieved up to 17 GHz. In order to suppress the interference of some undesired narrowband signal such as wireless local‐area network (WLAN) radio signal, a notched band is created for the UWB bandpass filter, which is realized by forming one stepped slot on each of the feedlines, respectively. The measured results show that a notched band with 2.01% fractional bandwidth at the center frequency of 5.85 GHz can be achieved and its suppression is about ?19 dB.     

Dual‐band band pass filter using stub‐loaded open‐loop resonators with wide controllable bandwidths

Two dual‐band band pass filters (BPF) using stub‐loaded open‐loop (SLOL) resonator are presented in this article. A novel coupling tuning method by changing the relative coupling position of the resonators is proposed to control the bandwidth of each passband in a wide range. Transmission zeros are created to improve the selectivity by source‐load coupling. Because of the large ratio of two bandwidths, a novel dual‐band matching method is proposed to match the different load impedances at two passband frequencies to the same source impedance. Hence, relax the fabrication requirement of gap. The proposed dual‐band band pass filter is designed and fabricated. The measured 3 dB fractional bandwidths (FBWs) of two 2.45/5.25 GHz dual‐band BPFs are 6.5%/14.5% and 9.8%/5.5%, respectively. The results are in good agreement with the simulation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:367–374, 2014.     

A balanced tri‐band bandpass filter with high selectivity and controllable bandwidths

In this article, a balanced tri‐band bandpass filter (BPF) with high selectivity and controllable bandwidths is proposed. Two differential‐mode (DM) passbands are formed by applying stepped impedance resonators into the design. Uniform impedance resonators are introduced to realize the third DM passband. Moreover, frequencies and bandwidths of DM passbands can be independently controlled by the lengths of resonators and the gaps between them. In addition, good DM transmission can be realized while high common‐mode suppression is achieved intrinsically without affecting the DM parts, thereby simplifying the design procedure significantly. In order to validate the practicability, a balanced tri‐band BPF operating at 2.45 GHz, 3.5 GHz, and 4.45 GHz is fabricated and designed. A good agreement between the simulated and measured results is observed.     

Compact low‐cost microstrip lowpass filter with sharp roll‐off and wide attenuation band

A compact low‐cost lowpass filter (LPF) with sharp roll‐off and wide attenuation band using stepped impedance resonator loaded with interdigital fingers and U‐shaped resonator is recommended in this article. The proposed LPF has a cut‐off frequency of 1.2 GHz with a sharp roll‐off 135 dB/GHz and passband insertion loss 0.35 dB. An array of two different shapes of defected ground structures are etched in the ground plane for introducing additional transmission zeroes to enhance the stopband performance. The relative stopband suppression is achieved up to 171% with a suppression factor of 2. The proposed structure is modelled, fabricated, and measured. The measurement results are found to be well‐matched with the simulated ones. Eventually, a high figure of merit of 21 600 is achieved.     

Ultra‐wideband bandpass filter on coplanar waveguide: Proposal and implementation

In this paper, a novel ultra‐wideband (UWB: 3.1 ～ 10.6 GHz) bandpass filter on coplanar waveguide (CPW) is presented, designed and implemented. At first, an open‐ended nonuniform or multiple‐mode resonator with three distinctive sections is constructed and investigated toward generating the first three resonant modes occurring around the lower‐end, center, and higher‐end of the UWB band. Then, a CPW interdigital capacitor element with enlarged ground‐to‐ground distance is characterized to excite two additional resonant poles below and above the UWB's center. As a result, a five‐pole UWB bandpass filter with only one full‐wavelength is constituted. Its performance is studied on the basis of a simple cascaded transmission‐line network, whose parameters are extracted from our self‐calibrated method of moments. After the optimized results are confirmed by full‐wave simulation over the filter layout, a UWB filter sample is fabricated to demonstrate the actual UWB passband behavior with the 2.8–10.2 GHz bandwidth, where the insertion loss is less than 1.5 dB and variation in group delay is less than 0.33 ns. © 2007 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2007.     

A tunable 0.86‐3.83 GHz bandpass filter with high selectivity

This letter presents a tunable bandpass filter (BPF) with wide tuning range of center frequency and high selectivity. The wide frequency tuning range is achieved by two pairs of switchable varactors‐tuned parallel coupled line resonators with direct‐feed structure, which can be switched to lower and higher frequency resonator modes by using p‐i‐n diodes. Since the electromagnetic mixed coupling and frequency‐variant source‐load coupling are incorporated in this configuration, three self‐adaptive transmission zeros (TZs) close to the tunable passband are obtained. Also, three TZs can almost keep the same relative location of passband to achieve continuous high selectivity and good out‐of‐band rejection over the whole frequency tuning range. Meanwhile, by selecting a proper coupling region, a constant fractional bandwidth (CFBW) in the frequency tuning process can be realized. For verification, a tunable 0.86‐3.83 GHz BPF with a 12% CFBW and high selectivity is designed, fabricated and measured. The experimental results show the proposed filter has the advantages of wide tuning range and high selectivity.     

Wideband bandpass filter based on U‐slotted SW‐HMSIW cavities

A wideband bandpass filter (BPF) is designed based on U‐slotted slow wave half mode substrate integrated waveguide (SW‐HMSIW) cavities. Similar to the substrate integrated waveguide (SIW), the SW‐HMSIW can also achieve a highpass characteristic while the lateral dimensions can be reduced by about 50%. By etching a U‐shape slot on the SW‐HMSIW cavity, a multiple‐mode resonator (MMR) can be realized, which can achieve a wide passband response and make the overall dimension of the filter much more compact. A wide passband, covering from 6.0 GHz to 10.65 GHz with a FBW about 58.13% is achieved. The measured minimum insertion losses including the losses from SMA connectors are 1.1 dB and return losses are better than 10 dB. Besides, the group delay varies between 0.2 and 0.5 ns within the passband. To validate its practicability, a wideband SW‐HMSIW BPF fabricated on a double‐layer printed circuit board (PCB) is designed and examined. The proposed filter has a more than 54% size reduction compared to the other designs reported in open literatures. The measured results have a good agreement with the simulated results. The effective size of the fabricated filter is about 27 mm × 8.55 mm.     

Capacitive Coupled Wide-Notch Stepped Impedance Narrow-Band Bandpass Filter for WiMax Application

The development of wireless communication standards necessitates optimal filter design for the selection of appropriate bands of frequencies. In this work, a compact in size pair of parallel coupled symmetric stepped impedance-based resonator is designed with supporting to the WiMAX communication standards. The coupled resonator is tuned to allow the frequency band between 3.4 GHz and 3.8 GHz, which is centered at 3.6 GHz. A parasitic effect of capacitively coupled feed structure is used for exciting the two symmetrical stepped impedance resonators. The bandwidth and selectivity of the filter are enhanced with the change of characteristic impedances and controlling the coupling gap between resonators. This design offers single narrow sharp passband selectivity as well as multiple stopband harmonic suppression arising as a result of multiple transmission zeros. The designed filter operates with a fractional bandwidth (FBW) of 11.47%. The proposed single narrowband bandpass filter provides better suppression in either side of the tuned frequency (3.6 GHz) without degrading the passband performance. Also, this novel filter offers an insertion loss of about −0.08 dB and a return loss of greater than −30 dB in passband. This approach is useful for eliminating unwanted spurious harmonics responses that enter the desired response. The suggested bandpass filter has been simulated using Advanced Design System (ADS) tool, and the measurement has been made using a network analyzer, and the results are reported.     

Compact ultra‐wideband bandpass filter with configurable stopband based on diamond‐shape resonator

An ultra‐wideband compact bandpass filter (BPF) with configurable stopband by tuning transmission zeroes is proposed in this paper. The ultra‐wideband bandpass response is based on a diamond‐shape resonator consisting of a pair of broadside coupled diamond‐shape microstrip lines, within which a diamond shape defected ground structure (DGS) is etched in the middle. Flexible transmission zeros realized by open and short stubs can be easily adjusted to improve band selectivity and harmonic suppression. Measurement result shows that the dedicated device has a 3 dB fractional bandwidth of 148% (0.94‐6.36 GHz) with 20 dB rejection stopband from 6.87 to 9.7 GHz (77.5%) which agrees good with the simulate performance. The overall size of the proposed BPF is 0.27 λ_g × 0.23 λ_g.