Design of a compact orthogonal fed self‐diplexing bowtie‐ring slot antenna based on substrate integrated waveguide

In this article, a novel design of compact cavity‐backed slot antenna based on substrate integrated waveguide (SIW) technology is presented for dual‐frequency communication services. A single layer printed circuit board is applied to implement the proposed antenna. The bowtie‐ring slot engraved on the SIW square cavity is excited using two orthogonal microstrip feed lines to operate at two distinct frequencies (6.62 GHz and 11.18 GHz). The proposed antenna allows each of these frequencies to be designed independently. A prototype of the proposed cavity‐backed antenna that radiates at both 6.62 GHz and 11.18 GHz is fabricated and measured. The port isolation better than 29.3 dB is achieved by utilizing the transmission zeros (TZs), which are produced due to the orthogonal feed lines, TE₁₁₀ mode and coupling between the TE₁₂₀ and TE₂₁₀ modes. The measured peak gains of the proposed diplexing antenna are 5.77 dBi and 5.81 dBi at lower and upper resonating frequencies, respectively. The proposed dual‐frequency antenna exhibits the front‐to‐back‐ratio (FTBR) and cross‐polarization level greater than 26 dB and 21 dB, respectively, at both resonating frequencies.     

Dual‐wideband filtering power divider based on center‐fed three‐line coupled structure

In this article, a dual‐wideband filtering power divider is proposed by using a center‐fed three‐line coupled structure with three open stubs and two isolation resistors. The center‐fed three‐line coupled structure can generate two wide passbands separated by a transmission zero (TZ). The three open stubs can achieve four TZs around the two passbands, which is conducive to the frequency selectivity. Compared with the reported designs, the bandwidth is extended and the performance of isolation, insertion loss and circuit size can reach balance. The proposed design is implemented with size of 0.22 λ_g × 0.39 λ_g (λ_g is the guided wavelength at the center frequency of the lower passband) which exhibits the 3‐dB fractional bandwidths of 56.5%/24.27% and the insertion loss of 0.51/0.68 dB at the center frequency of two passband (f₁/ f₂) of 1.94/4.2 GHz, while the isolation at f₁/f₂ are higher than 22.5/20.1 dB.     

Substrate‐integrated waveguide filtering crossovers with improved selectivity

Two substrate‐integrated waveguide (SIW) filtering crossovers with high selectivity are presented. The orthogonal degenerate TE₂₀₁ and TE₁₀₂ modes in center square cavity are employed to realize the cross transmission and channel isolation. The offset coupling positions are then exploited for surrounding TE₁₀₁‐mode rectangular cavities to produce transmission zeros (TZs) above the passband in the first crossover design or for TE₂₀₁‐mode oversized rectangular cavities to generate one TZ on each side of the passband in the second crossover design. The footprint of first crossover has greatly been reduced, while the selectivity of both crossovers has been greatly improved. Two prototypes centered at 20 GHz are designed, fabricated, and tested for demonstration, showing good agreement between the simulated and measured results.     

Independently controllable dual‐band filter using single quad‐mode silver‐loaded dielectric resonator

This article proposes a novel bandpass filter with two controllable passbands using a single quad‐mode silver‐loaded dielectric resonator (DR). The silver plane is inserted in the middle of the cubic DR and two degenerate pairs are used to build the two passbands. Because of the distinct E‐field distributions, the silver plane has significant effect on the degenerate pair (TE^x₁₁₂ and TE^y₁₁₂), whereas another one (TE^x₁₁₁ and TE^y₁₁₁) remains unchanged. With the aid of the silver plane, both center frequencies and bandwidths of the two bands can be controlled independently. To verify the proposed idea, a prototype dual‐band BPF is designed and fabricated. Good agreement between simulated and measured results can be observed.     

Filtering balanced‐to‐single‐ended power dividing network

In this article, the filtering balanced‐to‐single‐ended power dividing networks are proposed. Except the fundamental functions of differential‐mode transmission, common‐mode suppression, and out‐of‐phase single‐ended output ports with isolation, the proposed designs show the advantages of wide controllable range of differential‐mode bandwidth, multiple transmission zeros (TZs), and wide bandwidth for high out‐of‐band suppression. The frequencies of TZs, bandwidth, isolation, and common‐mode suppression can be controlled by the parameters. For demonstration, three prototypes (Deigns I, II, and III) with two, four, or six TZs are implemented. The measured results show that design I (II and III) has an insertion loss of 0.38 dB (0.7 dB and 0.8 dB), an operating bandwidth of 12.5% (7.5% and 6.9%), and a bandwidth for 30‐dB out‐of‐band suppression of 0.06f₀ (0.09f₀ and 0.14f₀). The isolation and common‐mode suppression inside the passbands of the three prototypes are all larger than 17 and 38 dB, respectively.     

Wideband bandpass filter based on U‐slotted SW‐HMSIW cavities

A wideband bandpass filter (BPF) is designed based on U‐slotted slow wave half mode substrate integrated waveguide (SW‐HMSIW) cavities. Similar to the substrate integrated waveguide (SIW), the SW‐HMSIW can also achieve a highpass characteristic while the lateral dimensions can be reduced by about 50%. By etching a U‐shape slot on the SW‐HMSIW cavity, a multiple‐mode resonator (MMR) can be realized, which can achieve a wide passband response and make the overall dimension of the filter much more compact. A wide passband, covering from 6.0 GHz to 10.65 GHz with a FBW about 58.13% is achieved. The measured minimum insertion losses including the losses from SMA connectors are 1.1 dB and return losses are better than 10 dB. Besides, the group delay varies between 0.2 and 0.5 ns within the passband. To validate its practicability, a wideband SW‐HMSIW BPF fabricated on a double‐layer printed circuit board (PCB) is designed and examined. The proposed filter has a more than 54% size reduction compared to the other designs reported in open literatures. The measured results have a good agreement with the simulated results. The effective size of the fabricated filter is about 27 mm × 8.55 mm.     

Coupled‐line band‐pass filter with T‐shaped structure for high frequency selectivity and stopband rejection

A coupled‐line band‐pass filter (BPF) with T‐shaped stub structure is presented. Five transmission poles within the passband and eight deep transmission zeros (TZs) from 0 to 2f₀ (f₀ denotes filter's center frequency) are realized through input impedance calculations. With the simple T‐shaped structure, the positions of six TZs can be appropriately adjusted to achieve high frequency selectivity and stopband rejection. For demonstration, a BPF prototype centered at 2.05 GHz is designed and fabricated, whose measured rejection levels are of over 45.5 dB at lower stopband and better than 19.5 dB at upper stopband. The simulation and measurement results are in good agreement, which validates the design idea.     

Compact high gain half‐mode substrate integrated waveguide cavity antenna using hybrid mode

In this article, a compact fully planar high gain antenna based on half‐mode substrate integrated waveguide (HMSIW) cavity is presented. The design uses a novel configuration of HMSIW cavity with high length to width ratio along with tapered open edge and a pair of slot stub. The high length to width ratio of the cavity helps to excite closely spaced multiple TE^y_m10 cavity modes within comparatively smaller footprint due to use of the HMSIW cavity. These modes combine to give hybrid mode resonance in the cavity which helps to generate a narrow beam high gain radiation pattern of the antenna. The size of the proposed antenna is further reduced and a pair of slot stub is put along the sidewall of the cavity which helps to sustain similar hybrid mode field distribution within much smaller dimension. A size reduction of 76.7% is achieved in the proposed design configuration without degrading much of the gain performance. The proposed antenna resonates at 9.8 GHz with a gain of 7.9 dBi which is much higher than other reported HMSIW cavity antenna. The proposed antenna may find application in point to point communication, short range radar in X band.     

Half mode substrate‐integrated waveguide‐loaded evanescent‐mode bandpass filter

In this article, a filter size reduction of 46% is achieved by reducing a substrate‐integrated waveguide (SIW)‐loaded evanescent‐mode bandpass filter to a half‐mode SIW (HMSIW) structure. SIW and HMSIW filters with 1.7 GHz center frequency and 0.2 GHz bandwidth were designed and implemented. Simulation and measurements of the proposed filters utilizing combline resonators have served to prove the underlying principles. SIW and HMSIW filter cavity areas are 11.4 and 6.2 cm², respectively. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Novel single-layer dual-band half-mode substrate integrated waveguide filter and filtering power dividers with very compact sizes

In this article, a novel single-layer dual-band (DB) half-mode substrate integrated waveguide (HMSIW) filter and three equal/unequal DB HMSIW filtering power dividers (FPDs) with super-compact sizes have been proposed. In order to design the proposed devices, the evanescent mode technique and the metamaterial concept have been used, simultaneously. Two passbands have been generated below the cut-off frequency of the HMSIW structure by etching a new compact DB metamaterial unit cell with effective negative permittivity in two different frequencies on the metal surface of the HMSIW structure. The center frequencies of these two passbands can be simply controlled by changing the size of the DB metamaterial unit cell. To confirm the design concept, three prototypes of the DB structures working at 2.4 and 3.5 GHz are simulated, constructed, and measured. The overall dimension of the designed DB HMSIW filter and DB HMSIW FPDs are approximately 0.12 λ_g × 0.11 λ_g. Compared to other existing devices, the performance of the proposed structures is very satisfactory. Compact size, easy integration, easy fabrication process, low cost, low loss, and high selectivity are the advantages of the designed structures.     

A novel dual‐band bandpass filter using co‐directional split ring resonators with closely spaced passbands and wide upper stopband

In this article, interdigital capacitor loaded co‐directional split ring resonators (CDSRRs) and their dual‐band bandpass filter applications are proposed. The proposed resonator is formed by nested open loop resonators having open ends at the same place unlike conventional split ring resonators (SRRs). In addition, the inner open loop resonator has interdigital capacitor located between the open ends. The proposed resonator exhibits dual resonance behavior with a small center frequency ratio. Both of resonance frequencies can be controlled due to the changes in the interdigital capacitor and the electrical length of the outer resonator. A dual‐band microstrip bandpass filter is designed by using the proposed CDSRR. Two CDSRRs are used to obtain two poles in each passband. Overall electrical length of the designed filter is 0.23 λ_g × 0.14 λ_g (0.0329 λ_g²), where λ_g is the guided wavelength for the used substrate at the lowest passband center frequency of 1.8 GHz. A small center frequency is obtained by adjusting the second passband at 2.27 GHz. A very wide upper stopband, closely spaced passbands, low insertion losses and high selectivity at both passbands can be obtained by means of the proposed structure. The designed filter was also fabricated and tested. The measured results show a very good agreement with the predicted results.     

Compact dual‐band bandpass filter and diplexer using hybrid resonant structure with independently controllable dual passbands

In this article, a compact dual‐band bandpass filter (BPF) is developed using a hybrid resonant structure, which consists of a microstrip stub‐loaded dual‐mode resonator and a slotline stub‐loaded dual‐mode resonator. These two resonators, both having two controllable resonant modes and one transmission zero (TZ), are analyzed and used to construct two desired passbands of a dual‐band BPF. Multiple TZs are generated by introducing a source‐load coupling, thus improving the selectivity of the passbands. Then, the dual‐band BPF is reshaped to configure a compact diplexer. The inherent TZs of the two proposed resonators are designed to improve the frequency property and port isolation of the diplexer. Finally, a dual‐band BPF and a diplexer with the lower and upper passbands centered at 2.45 and 3.45 GHz, respectively, are designed, fabricated, and measured to verify the proposed structure and method.     

A tunable third‐order bandpass filter based on combining dual‐mode square‐shaped substrate integrated waveguide resonator with triangular‐shaped resonator

A frequency reconfigurable third‐order bandpass filter based on two substrate integrated waveguide (SIW) cavities is presented in this article. The purposed filter consists of a dual‐mode square‐shaped resonator and a triangular‐shaped resonator. In the square‐shaped cavity, four lumped capacitors are loaded as electrical tuning elements in the area where the electric fields of diagonal TE₂₀₁ and TE₁₀₂ modes are strongest. And an another capacitor is loaded at the suitable region of the triangular‐shaped cavity. Square‐shaped cavity introduces two transmission zeros and the triangular‐shaped cavity can suppress out‐of‐band spurious modes. The method that combines the resonators with different shapes and multiple modes into an organic whole cannot only achieve synchronous tuning but also have complementary advantages and improve out‐of‐band rejection. To verify its practicality, a SIW reconfigurable bandpass filter is simulated when the capacitance value varies from 0 to 1.4 pF and measured at 0.7, 0.8, and 0.9 pF, respectively. Measured results show that when the center frequency is tuned from 3.42 to 3.52 GHz, the proposed filter exhibits good tuning performance with insertion loss of less than 2.5 dB and return loss of better than 10 dB, which is suitable for fifth‐generation communication system.     

Dual‐passband bandpass‐filtering power divider using half‐mode substrate integrated waveguide resonator with high frequency selectivity

In this paper, a half‐mode substrate integrated waveguide (HMSIW) power divider with bandpass response and good frequency selectivity is proposed. The proposed power divider includes input/output microstrip lines, four HMSIW resonators, cross‐coupling circuits, and an isolation resistor. The dual‐band bandpass‐filtering response is obtained by using the dual‐mode slotted HMSIW. To get good frequency selectivity, the input/output cross‐coupling circuits have been used, and several transmission zeros can be observed. A dual‐band filtering‐response HMSIW power divider is designed, fabricated and measured. The total size of the fabricated power divider is 0.58λg × 0.45λg. The measured results show a reasonable agreement with the simulated ones. The measured central operating frequencies of the dual‐band HMSIW power divider are at 2.43 and 3.50 GHz, respectively. The measured 3‐dB fractional bandwidth is about 13.3% and 6.3% in the two passbands, and the measured output isolation is about 20 dB.     

A triple‐slotted substrate integrated cavity‐fed 2 × 2 metasurface antenna with wide bandwidth

This article presents a triple‐slotted substrate integrated cavity (SIC)‐fed 2 × 2 metasurface antenna. Three modes can be obtained including TM₁₀ mode of the metasurface, TE₂₁₀, mode and TE₃₁₀ mode of the SIC. The TE₂₁₀ mode of SIC radiates through the two side slots and is coupled to the metasurface mainly by the two side slots, while the TE₃₁₀ mode of SIC is mainly coupled to the metasurface by the middle slot. Comparing with the reported SIC‐backed slot antenna, dual‐slotted SIC‐fed patch antenna or the metasurface antenna, the proposed antenna exhibits the advantage of wide bandwidth with flat gain. One prototype operated at 10 GHz was fabricated and measured with 10‐dB fractional bandwidth of 33%, the gain of 8.1 dBi at the center frequency, the cross polarization level of 20 dB and the gain ripple of 1.5 dB.     

Compact,dual-band,and hybrid filter based on combline and substrate integrated waveguide resonators

A novel compact hybrid dual-band bandpass filter based on combline and substrate integrated waveguide (SIW) resonators is proposed. By exploring an SIW-based hybrid cavity structure, a controllable dual-band response is achieved. The low-frequency passband is obtained by the combline, or mushroom resonators and the high-frequency passband is formed by the TE₁₀₁ and TE₃₀₁ modes. Unlike other designs that use the main mode and the high-order mode of the same resonator, we innovative use the TE301 mode of the rectangular cavity and cleverly divide this rectangular cavity into two small cavities, and use its TE101 mode to form the second passband with the TE301 mode of the large cavity. To improve the selectivity and out-of-band suppression, three transmission zeros are configured in this design. In order to verify the proposed design concept, a compact dual-band filter using this hybrid resonance structure is fabricated and measured. It demonstrates good filtering performance, including a compact size of 0.45 × 1.09 λ₀, a low insertion loss of 0.57 and 1.67 dB in the two bands, and a high-design flexibility.     

SIW cavity‐backed 24° inclined‐slots antenna for ISM band application

In this article, a novel resonant series slot linearly polarized antenna is realized using substrate integrated waveguide (SIW) technology for industrial scientific medical radio band (ISM) at 5.8 GHz. The proposed antenna consists of two 24° inclined slots and two metallic vias to produce alternate inductive and capacitive loads. The rectangular slots are introduced at the top metallic surface at an angle of 24° from the Y‐axis to excite a hybrid mode (TE₁₁₀ + TE₁₂₀) near to the modified cavity mode TE₁₂₀. The resonant slots are excited with the help of an inset microstrip feedline which retain its planar integrability. The slots are excited to resonate in the TE₁₂₀ mode at 5.8 GHz. To enhance the bandwidth, the location of two shorting vias are optimized in proximity to the slots. These vias help to couple the hybrid mode and the cavity modes in the desired frequency band, which leads to enhancement in the bandwidth significantly. The proposed geometry is fabricated and experimentally verified. The measured and simulated results depict a good co‐relation which show measured ?10 dB fractional bandwidth of 5.2% with a maximum gain of 7.15 dBi and the front to back ratio better than 15 dB at 5.8 GHz.     

A dual‐band superconducting filter with a large bandwidth ratio

In this study, we propose a stepped‐impedance‐stub loaded interdigital capacitor resonator for design of a dual‐band band‐pass filter with a large bandwidth ratio. The presented resonator has strong and weak couplings in the upper passbands (UPs) and lower passbands (LPs), respectively, so as to form a large upper/lower bandwidth ratio. Adopting a dual‐branch phase‐matched feedline structure can meet the external quality factors required for the UP/LP. Therefore, these two passbands, defined by their respective center frequencies and bandwidths, can be manipulated independently. A four‐pole dual‐band example filter with a lower bandwidth of 20 MHz at 1576 MHz and an upper bandwidth of 200 MHz at 2450 MHz is successfully designed on an YBCO/MgO superconducting wafer. The filter exhibits excellent frequency responses. The upper/LPs show insertion losses below 0.07/0.22 dB and return losses above 15.3/15.3 dB. The stopband rejection is better than 57 dB until the first spurious passband up to 6150 MHz (3.9f_L).     

A highly selective balanced wideband bandpass filter based on nested split‐ring resonators

A balanced wideband bandpass filter (BPF) with a high frequency selectivity, controllable bandwidth, and good common‐mode (CM) suppression based on nested split‐ring resonators (SRRs) is proposed in this article. The proposed nested SRRs are applied to form three transmission poles (TPs) that can achieve a wide differential‐mode (DM) passband centered at 3.0 GHz. Meanwhile, two transmission zeros (TZs) are generated to realize a high frequency selectivity of the DM passband. Moreover, TPs and TZs can be quasi‐independently controlled by changing the physical lengths of SRRs and the gaps between them, which can greatly improve the flexibility and practicality of the design. The proposed balanced BPF is fed by balanced microstrip‐slotline (BMS) transition structures. For the CM signals, the BMS transition structures can achieve a good wideband CM suppression without affecting the DM ones, thereby simplifying the design procedure. In order to validate its practicability, a balanced wideband BPF is fabricated and a good agreement between the simulated and measured results is obtained.     

A dual‐band half‐mode substrate integrated waveguide‐based antenna for WLAN/WBAN applications

A dual‐band half‐mode substrate integrated waveguide (HMSIW) based cavity‐backed antenna is proposed for WLAN/WBAN applications at 5/5.8 GHz, respectively. A semi‐hexagonal slot is introduced on the top plane of the cavity primarily for radiation. This slot offers miniaturization for both the TM₂₁₀ and TM₀₂₀ modes. Later on, two rectangular slits are loaded on the open edge of the patch, to provide miniaturization and tuning mainly for the higher frequency band. The performance of the proposed antenna is investigated in free space and in proximity of the pork tissues. In free space conditions, the measured ?10 dB fractional bandwidths are 3% and 3.1% along with peak gains of 6.25 and 6 dBi for the frequency bands at 5 and 5.8 GHz, respectively. In proximity of the pork tissues, the measured fractional bandwidth is 3.2% along with the efficiency of 81.5% at 5.8 GHz. The specific absorption rate (SAR) is 0.48 mW/g averaged over 1 g of tissues with 100 mW input power.