Prospects and challenges of mini‐LED and micro‐LED displays

We review the emerging mini/micro–light‐emitting diode (LED) displays featuring high dynamic range and good sunlight readability. For mini‐LED backlit liquid crystal displays (LCDs), we quantitatively evaluate how the device contrast ratio, local dimming zone number, and local light profile affect the image quality. For the emissive mini/micro‐LED displays, the challenges of ambient contrast ratio and size‐dependent power efficiency are analyzed. Two figure‐of‐merits are proposed for optimizing the optical and electrical performances of mini/micro‐LED displays.     

Energy‐efficient liquid‐crystal displays (e2‐LCDs) using a photonic‐crystal backlight system

Abstract— Cholesteric liquid crystals automatically form one‐dimensional photonic crystals. For a photonic crystal in which light‐emitting moieties are embedded, unique properties such as microcavity effects and simultaneous light emission and light reflection can be expected. Three primary‐color photonic‐crystal films were prepared based on cholesteric liquid crystal in which fluorescent dye is incorporated. Microcavity effects, i.e., emission enhancement and spectrum narrowing, were observed. Two types of demonstration liquid‐crystal displays (LCDs) were fabricated using the prepared photonic‐crystal films in a backlight system. One is an area‐color LCD in which a single photonic‐crystal layer is used for each color pixel and the other is a full‐color TFT‐LCD in which three stacked photonic‐crystal layers are used as light‐conversion layers. The area‐color LCD was excited by using 365‐nm UV light, and the full‐color TFT‐LCD was excited by using 470‐nm blue LED light. Because of the photonic crystal's unique features that allow it to work as light‐emitting and light‐reflecting layers simultaneously, both LCDs demonstrate clear readable images even under strong ambient light, such as direct‐sunlight conditions, under which conventional displays including LCDs and OLED displays cannot demonstrate clear images. In particular, an area‐color LCD, which eliminated color filters, gives clear images under bright ambient light conditions even without backlight illumination. This fact suggests that a backlight system using novel photonic‐crystal layers will be suitable for energy‐efficient LCDs (e²‐LCDs), especially for displays designed for outdoor usage.     

Non‐polar‐oriented InGaN light‐emitting diodes for liquid‐crystal‐display backlighting

Abstract— This article addresses spontaneously polarized light emission from GaN‐based light‐emitting diodes (LEDs) fabricated on electrically non‐polar crystallographic orientations and application of spontaneously polarized emission for backlighting of liquid‐crystal displays (LCDs). The first half of the article describes polarized light emission from GaN‐based LEDs and its role in solid‐state lighting technology. The second half reports on our experimental work to explore the potential of non‐polar LEDs for LCD backlighting applications. Optical transmission of non‐polar LED emission was characterized through a liquid‐crystal layer. Extinction ratios of 0.21 were measured between zero and an applied bias voltage to the liquid‐crystal cells. These extinction ratios are not particularly high yet; nevertheless, the experiment has demonstrated the potential of such non‐polar LEDs for LCD backlighting.     

Backlight unit with double‐surface light emission using a single micro‐structured lightguide plate

Abstract— A novel illumination system for a liquid‐crystal‐display (LCD) module used in a dual‐display cellular phone has been developed. A double‐surface light‐emitting backlight uses a single light‐guide plate to illuminate both LCDs. A single lightguide, two prism sheets, and four light‐emitting diodes (LED) were used in the new structure, compared with ten components and two sets of light sources with six LEDs in the current backlight. The thickness and power consumption of the new backlight were reduced by a factor of 0.59 and 0.67, respectively.     

Deformed nanostructure of photo‐induced biaxial cholesteric films and their application in VA‐mode LCDs

Abstract— Novel biaxial retardation films made from photo‐induced deformed cholesteric liquid‐crystal (LC) nanostructures using reactive mesogen mixtures (RMMs) for a viewing‐angle compensation of vertically aligned liquid‐crystal displays (VA‐LCDs) was developed. The deformed cholesteric LC nanostructure has been observed by X‐ray‐diffraction (XRD) measurement. The birefringence of the film was described well by our optical model based on a form birefringence theory. The VA‐LCDs with photo‐induced biaxial cholesteric films have excellent viewing‐angle properties.     

Electro‐optical characteristics of ion‐beam‐aligned FFS‐LCDs on diamond‐like‐carbon thin film

Abstract— A fringe‐field‐switching (FFS) mode cell having LC alignment has been developed by using a non‐rubbing method, a ion‐beam‐alignment method on a‐C:H thin film, to analyze the electro‐optical characteristics of this cell. The suitable inorganic thin film for FFS‐LCDs and the alignment capabilities of nematic liquid crystal (NLC) have been studied. An excellent voltage‐transmittance (V‐T) and response‐time curve for the ion‐beam‐aligned FFS‐LCDs were observed using oblique ion‐beam exposure on DLC thin films.     

A broadband wide‐incident‐angle reflective polarization converter

Abstract— A high‐performance reflective polarization converter which could be used in a backlight recycling system for liquid‐crystal‐display (LCD) devices is proposed. The device consists of a twisted‐nematic (TN) liquid‐crystal film, a uniaxial A‐plate, and a reflector. The configuration parameters, such as thickness and orientation of the films, are optimized using a genetic algorithm. As a result, the design can convert light from TM to TE polarization (or TE to TM) at a maximum 99.7%, minimum 91.3%, and average 96.7% conversion efficiency for the entire visible spectrum and incident angle from 0 to 60°. Such a broadband reflective polarization converter is particularly useful for enhancing the light efficiency and reducing the power consumption of LCDs.     

Photoalignment and photo‐patterning of planar and homeotropic liquid‐crystal‐display configurations

Abstract— Optical alignment and micro‐patterning of the alignment of liquid‐crystal displays (LCDs) by linear photopolymerization (LPP) technology renders high‐quality multi‐domain twisted‐nematic (TN) and supertwisted‐nematic (STN) displays with broad fields of view over wide temperature ranges feasible. The prerequisites are the generation of photo‐induced high‐resolution azimuthal alignment patterns with defined bias‐tilt angles 0° ≤ θ ≤ 90°. For the first time, LPP‐aligned single‐ and dual‐domain vertically aligned nematic LCDs (VAN‐LCDs) are presented. Dual‐domain VAN‐LCDs are shown to exhibit broad fields of view which are further broadened by combining the displays with LPP‐aligned optical compensators made of liquid‐crystal polymers.     

Single‐cell‐gap transflective liquid‐crystal display using double‐ and single‐mode approaches

Abstract— In this paper, many popular methods to study transflective liquid‐crystal‐displays (LCDs) have been discussed, and several new transflective LCD configurations with a single‐cell gap have been proposed. The traditional double‐cell‐gap method gives the best match of the transmittance/reflectance voltage curve (TVC/RVC) and also the widest viewing angle, but also brings the highest fabrication complexity. The single‐cell‐gap transflective LCD is much easier to fabricate and also shows a good match of TVC/RVC. A new methodology has been shown to find optimal configurations for single‐cell‐gap transflective LCDs. New configurations using multimode in a single pixel include twisted nematic (TN) optically compensated bend (OCB), TN electrically controlled birefringence (ECB), and TN low‐twisted nematic (LTN). TN and hybrid‐aligned nematic (HAN) modes have been investigated for single‐mode transflective LCDs. The results exhibit high contrast ratio, a good match of TVC/RVC, as well as wide viewing angle.     

Aggregate‐induced emission in light‐emitting liquid crystal display technology

Nowadays, liquid crystal displays (LCDs) with light‐emission are considered as energy‐efficient devices and are promising alternatives to conventional LCDs. To realize such possibility, strong fluorescent materials with a dichroic properties are required. Aggregate‐induced emission (AIE) is an unusual photophysical phenomenon shown by some luminogenic materials that will be highly emissive in their aggregate state. In this work, we studied the AIE effect of a luminescent liquid crystalline molecule TPE‐PPE in our LC system as a luminophore dopant. The result showed the excellent AIE effect that higher concentration of luminogen in the nematic LC host induced stronger luminescent intensity. Through exposure of a photoisomeriable alignment material sulfonic‐dye‐1, the photopatterning of a light‐emitting LC device was achieved with the use of the TPE‐PPE/nematic LC mixture.     

Self‐calibration three‐dimensional light field display based on scalable multi‐LCDs

Approach to achieve self‐calibration three‐dimensional (3D) light field display is investigated in this paper. The proposed 3D light field display is constructed up on spliced multi‐LCDs, lens and diaphragm arrays, and directional diffuser. The light field imaging principle, hardware configuration, diffuser characteristic, and image reconstruction simulation are described and analyzed, respectively. Besides the light field imaging, a self‐calibration method is proposed to improve the imaging performance. An image sensor is deployed to capture calibration patterns projected onto and then reflected by the polymer dispersed liquid crystal film, which is attached to and shaped the diffuser. These calibration components are assembled with the display unit and can be switched between display mode and calibration mode. In the calibration mode, the imperfect imaging relations of optical components are captured and calibrated automatically. We demonstrate our design by implementing the prototype of proposed 3D light field display by using modified off‐the‐shelf products. The proposed approach successfully meets the requirement of real application on scalable configuration, fast calibration, large viewing angular range, and smooth motion parallax.     

LED‐backlight feedback control system with integrated amorphous‐silicon color sensor on an LCD panel

Abstract— Thin‐film‐transistor liquid‐crystal displays (TFT‐LCDs) have the largest market share of all digital flat‐panel displays. An LCD backlighting system employing a three‐color red‐green‐blue light‐emitting diode (RGB‐LED) array is very attractive, considering its wide color gamut, tunable white point, high dimming ratio, long lifetime, and environmental compatibility. But the high‐intensity LED has problems with thermal stability and degradation of brightness over time. Color and white luminance levels are not stable over a wide range of temperature due to inherent long‐term aging characteristics. In order to minimize color point and brightness differences over time, optical feedback control is the key technology for any LED‐backlight system. In this paper, the feasibility of an optical color‐sensing feedback system for an LED backlight by integrating the amorphous‐silicon (a‐Si) color sensor onto the LCD panel will be presented. To minimize the photoconductivity degradation of a‐Si, a new laser exposure treatment has been applied. The integrated color‐sensor optical‐feedback‐controlled LED‐backlight system minimized the color variation to less than 0.008 Δu'v' (CIE1976) compared to 0.025 for an open‐loop system over the temperature range of 42–76°C.     

Electrically commanded surfaces: A new liquid‐crystal‐display concept

Abstract— Fast in‐plane switching of the optic axis was realized in liquid‐crystal displays (LCDs) based on the concept of Electrically Commanded Surfaces (ECS). According to this concept, the liquid‐crystal layer in such a display is aligned by means of thin ferroelectric liquid‐crystal‐polymer (FLCP) film deposited onto the inner side of the display substrates. An electric field, applied normal to the substrates, switches the molecules of the ferroelectric film, representing the commanded surface that, via elastic forces, further transfers to the liquid‐crystal layer. The concept of electrically commanded surfaces opens the door to a new generation of advanced LCDs exhibiting extraordinary performance such as fast in‐plane switching.     

Advanced liquid‐crystal materials for TFT monitor and TV applications

Notebook applications have been one of the most important driving forces behind the remarkable growth of liquid‐crystal displays (LCDs). LCDs have recently been well accepted in the monitor market and large growth is forecasted because of the replacement of CRTs. The next challenge for LCDs is the TV market. These new application areas are supported by advanced LC technologies such as film‐compensated twisted nematic (TN), in‐plane switching (IPS), and vertically aligned (VA) modes. Each TFT technology requires a corresponding LC material improvement. We will review the recent liquid‐crystal material development for these advanced LC technologies.     

Color performance of an MVA‐LCD using an LED backlight

Abstract— The color performance, including color gamut, color shift, and gamma curve, of a multi‐domain vertical‐alignment (MVA) liquid‐crystal display (LCD) using an LED backlight are calculated quantitatively. Simulation results indicate that an LED backlight exhibits better angular color uniformity and smaller color shifts than a CCFL backlight. Color gamut can be further widened and color shift reduced when using a color‐sequential RGB‐LED backlight without color filters, while the angular‐dependent gamma curves are less influenced using different backlights. The obtained quantitative results are useful for optimizing the color performance and color management of high‐end LCD monitors and LCD TVs.     

Tuning the alignment of liquid crystals by means of nano‐structured surfaces (Invited Paper)

Abstract— The solid‐surface/liquid‐crystal interactions, defining the field‐free alignment of the liquid crystal in conventional liquid‐crystal displays, are playing a vital role in their optical appearance and performance. Nano‐scale changes in the solid‐surface structure induced by light have been recently shown to affect the anchoring strength and the easy‐axis direction. Fine tuning of the anchoring strength is also demonstrated by nano‐structuring of the Langmuir‐Blodgett monolayer employed as liquid‐crystal alignment layers promoting homeotropic orientation. On the basis of nano‐engineering of the surface alignment properties, two novel alignment concepts have been introduced: electrically commanded surfaces (ECS) and high‐performance alignment layers (HiPAL). Nano‐structured polymers related to these concepts have been designed, synthesized, and used as materials for alignment layers in LCDs. ECS materials belong to the category of active alignment materials designed to mediate switching of the liquid crystal, whereas the HiPAL materials make possible the control of the molecular tilt angle in a broad range, from 0° to 90°, and they seem to enable the control of the anchoring strength as well. The nano‐structured alignment materials are strong candidates for implementation in a new generation of advanced liquid‐crystal displays and devices.     

Electro‐optic properties of an intrinsic half‐V‐mode FLCD and its application to field‐sequential full‐color LCDs using a poly‐Si TFT matrix array

Abstract— An intrinsic half‐V‐mode ferroelectric liquid‐crystal display (FLCD) exhibiting a high contrast ratio (300:1), owing to defect‐free gray‐scale capability, with a high response speed (τ ? 400 μsec) and good switchability with TFTs, has been developed. Furthermore, this FLCD features high‐temperature reliability owing to the use of a special hybrid alignment technique. We successfully fabricated an active‐matrix poly‐Si TFT field‐sequential full‐color (FS FC) LCD with XGA specifications and a 0.9‐in. diagonal using a half‐V‐mode FLCD and an RGB light‐emitting‐diode (LED) array microdisplay. It is shown that the fabricated active‐matrix FS FCLCD exhibits good moving‐image performance with high full‐color display capability.     

Retardation‐controlling color filter with two directly stacked retardation layers

Abstract— A polymerizable liquid crystal (PLC), the orientation of which can be frozen, is useful for making retardation layers. In this paper, a new color filter (CF) with retardation‐controlling layers made of PLC is reported. It has a positive A‐plate and a negative C‐plate, both directly stacked on a color‐filter layer. These two retardation layers exhibit good orientation ability, and function well as retarders, even when they are only 1/10 or less as thick as ordinary retardation films. The new CF also has excellent thermal stability. The change in retardation after heat treatment at 200°C for 30 min is around 5%, and there is no observable peeling. A prototype VA‐LCD made with our new CF provides good optical compensation, with the light leakage being extremely low in all azimuthal directions. This technology is very useful for making thin, highly reliable color filters for LCDs, even with other modes.     

LED‐backlit computer screens influence our biological clock and keep us more awake

Abstract— In commodity LC flat‐panel displays, the traditional CCFL backlight is being replaced more and more by LEDs. The typical spectrum of LED‐lit displays shows a significantly higher amount of blue light in the range around 464 nm. Blue light in this wavelength area suppresses the melatonin level in humans and thus effects the biological clock. Our hypothesis was that the amount of blue light reaching the human eye from a LED‐backlit display is sufficient to have a significant effect on the biological clock. The results of clinical user studies comparing the effects of LED‐ vs. CCFL‐backlit displays on humans, resulting from the emitted amount of 464‐nm light, will be presented. It was found that the LED‐backlit display causes significant suppression of melatonin, which effects the biological clock of the test persons, indicating the necessity for displays with a controllable 464‐nm emission. A technical concept for a display with such functionality will be presented.     

How to reduce light leakage and clipping in local‐dimming liquid‐crystal displays

Abstract— In conventional LCDs, the backlight is set to maximum luminance regardless of the image. For dark scenes, this approach causes light leakage and power waste. Especially, light leakage in dark scenes degrades the contrast ratio of LCDs; to circumvent this problem, local‐dimming systems have been proposed. In these systems, the LED backlight is divided into several local blocks and the backlight luminance of each local block is controlled individually, and pixel values are adjusted simultaneously according to the luminance profile of the dimmed backlight. In this paper, a method of determining the LED backlight luminance of each local block depending on the image is proposed; this method significantly improves the image quality of LCDs. First, we introduce methods of quantifying light‐leakage at dark gray levels and clipping at bright gray levels. Then, the proposed method to determine the dimming duty, which controls the LED backlight luminance by compromising between these two measures, was derived. The proposed algorithm preserves the original image with little clipping distortion and effectively reduces light leakage.