Dual‐band filter with high selectivity and wide stopband rejection

This article presents a highly selective dual‐passband filter based on stepped‐impedance‐resonator (SIR) and mixed electromagnetic coupling. First, the surface area of the filter is effectively reduced by the triangular topology. Second, four controllable transmission zeros are introduced by source‐load coupling feed and mixed electromagnetic, which increases the selectivity of the filter. Third, a perturbation structure is added to independently control the resonance points of each passband. Finally, the improved defect ground structure (DGS) is integrated to obtain wide stopband rejection. The measured S‐parameters are well agreement with the simulated results, which show that the center frequencies of the two passbands are 2.4 GHz and 5.2 GHz; and the passband insertion losses are 0.85 dB and 1.6 dB; and the relative bandwidths are 14.6% and 5.7%, respectively. Besides, the structure is with six transmission zeros, and 20 dB suppression for the third harmonic and the fourth harmonic are achieved. Compared with the traditional SIR double‐passband filter, this filter has many advantages, such as simple design, small size, small insertion loss, controllable frequency, high selectivity, and high spurious suppression.     

A broadband filter with two transmission zeros adopting a new design method

A new design method was proposed in this article to insert transmission zeros in the broadband filters. In this method, the coupling line was connected to a certain position on the resonator. And then the coupling strength was adjusted by the connecting position. The open end of the resonator was hung and then the cross‐coupling was introduced to realize transmission zeros. This coupling method could add an adjustable parameter to improve the freedom of design and convenient to insert the transmission zeros. To verify this method, a highly selective coupled‐line microstrip filter with two transmission zeros was designed, fabricated, and measured. The measured results were in good agreement with the simulated ones. The return and insertion losses of the broadband filter were better than 18 and 2 dB, respectively. The relative bandwidth of the filter (FBW) was more than 68%. The rectangular coefficient (30 dB:1 dB) was less than 1.21.     

Microstrip dual‐band bandpass filters using parallel‐connected open‐loop ring resonators

This article proposes a microstrip dual‐band bandpass filter that uses parallel‐connected open‐loop ring resonators. Compared to many microstrip dual‐band filters, the advantages of using microstrip open‐loop ring resonators are easy calculation (half‐guided‐wavelength), easy fabrication (equal width for all 50‐Ω lines and without grounding holes), and direct connection to external feed lines (reducing insertion loss caused by gap couplings). Another advantage of the filter is an asymmetrical feed on the ring resonator that provides sharp rejections at its adjacent bands. The input and output matches of resonators to the external feed lines are derived using a simple transmission‐line theory. The results of the derivation provide a simple design rule for filter designers. Simulated and measured results are presented with good agreement. The filter has minimum insertion loss of 1.25 dB at 1.85 GHz and 1.6 dB at 2.33 GHz. The 3‐dB fractional bandwidths are 5.9% for the 1.9‐GHz bandpass filter and 4.7% for the 2.4‐GHz bandpass filter, respectively. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2008.     

Ladder‐lattice bulk acoustic wave filters: Concepts,design, and implementation

This article presents a study of ladder‐lattice bulk acoustic wave (BAW) filters. First, a review of BAW technology and filters topologies is addressed. Next, a mixed ladder‐lattice BAW filter for application on W‐CDMA reception front‐ends (2.11–2.17 GHz) is presented. An improved solidly mounted resonators (SMR) technology was used for the filter implementation. The filter synthesis methodology is briefly described. Layout guidelines are discussed enabling an optimized filter design. The filter on‐wafer measurement results are as follows: ?3.55 dB of insertion loss, ?8.7 dB of return loss, an isolation higher than ?47 dB at the transmission band (1.92–1.98 GHz) and an improved selectivity (?30 dB at 2.14 GHz ± 60 MHz). Therefore, we can observe that the mixed topology combines the advantages of ladder and lattice networks, having very steep responses and an improved isolation at undesired bands. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2008.     

Synthesis and design of tunable bandpass filters with constant absolute bandwidth using varactor‐loaded microstrip resonator

This article presents two new types of tunable filters with constant absolute bandwidth using varactor‐loaded microstrip resonators. First, the second‐ and third‐order Butterworth tunable filters are designed based on the parallel coupled‐line J inverters. Second, a fourth‐order Chebyshev tunable filter is designed based on the alternative J/K inverters, in this design, two adjacent resonators are coupled with each other through a short‐circuited transmission line as the K inverter. The proposed two topologies can be easily extended to high‐order tunable filter. Three tunable bandpass filters with J and alternative J/K inverters, respectively, are built with a tuning range from ～1.8 to ～2.3 GHz. The measured second‐order filter has a 3‐dB bandwidth of 160 ± 6 MHz and an insertion loss of 2.4–3.8 dB. The third‐order filter shows a 3‐dB bandwidth of 197 ± 5 MHz and an insertion loss of 3.8–4.8 dB. The fourth‐order filter shows a 3‐dB bandwidth of 440 ± 5 MHz and an insertion loss of 2.1–2.6 dB. For all the designed filters, the measured results are found in excellent agreement with the predicted and simulated results. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:681–689, 2014.     

High isolation microstrip GaN‐HEMT Single‐FET Switch

In this contribution an analytical approach to the design of high‐isolation microwave transmission line‐resonated switches is presented. Simulated and measured performance of a GaN HEMT single‐FET switch cell topology and the one of a complete SPDT using the proposed approach are presented to demonstrate the approach feasibility and effectiveness. The resulting SPDT, operating at X Band, is featured by 1 dB insertion loss, isolation better than 37 dB all over the operating bandwidth and a power handling capability higher than 39 dBm. © 2010 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2010.     

Analytical modeling of H‐shape distributed topology with bandpass negative group delay behavior

This article describes an analytical modeling of a distributed negative group delay (NGD) circuit presenting a H‐shape topology. It acts as an innovative typical transmission line (TL) based topology with a feedback connected with an open‐stub termination. The equivalent circuit diagram is established based on TL representation of H‐topology constituting elements. The S‐matrix analytical model is developed. To validate the analytical model, a proof‐of‐concept prototype implemented in microstrip topology is designed, simulated, fabricated, and measured. The compared calculated, simulated, and measured S‐parameters are in very good agreement. In addition, the microstrip prototype confirm the bandpass NGD behavior of the H‐topology circuit with NGD value of approximately ?2 ns around the center frequency 1.67 GHz.     

A novel compact wideband filter using three‐mode dual‐ring resonator

A novel compact wideband filter using three‐mode dual‐ring resonator is presented in this article. The resonator is constructed by two quarter wavelength transmission lines and a cascaded half wavelength dual‐ring. Formulae based on even‐ and odd‐mode analysis are derived to analyze the locations of the transmission poles and zeros of the resonator. Due to the transmission zeros in the lower and upper stopbands, the proposed filter exhibits sharp attenuations near the passband as well as very wide stopband. The filter is successfully realized by full wave EM simulation and fabricated. The measured responses of the filter agree well with the design simulation, and show that the fabricated filter has an insertion loss of better than 1.5 dB in the passband and two rejections of greater than 20 dB in the stopbands from 0 to 10GHz.     

Miniaturized planar filters exhibiting flexible placement of three transmission zeros suitable for duplexer design

In this work, we show that a stub‐loaded open‐loop double resonator filter can produce three transmission zeros at finite frequencies close to the passband when designed using our proposed asymmetric feed point topology. We demonstrate that by selecting the length of the stub, the placement of double transmission zeros on either the high side of the passband or the low side of the passband can be selected. This selection can be achieved by using a single design parameter: the stub length. The flexibility in the double zero placement makes these filters particularly advantageous for duplexer designs. Two duplexers are fabricated using the proposed filter topology in a microstrip on a duroid substrate and substrate‐embedded stripline via Low‐Temperature Cofired Ceramic technology (LTCC). The measurements show steep attenuation of approximately 30 dB, close to the filters' passband as well as a compact size down to 0.075λ × 0.17λ.     

Wideband balun filter on slot‐line resonator with intrinsic balanced performance in magnitude and phase

In this article, a novel wideband balun filter on the coupled slotline‐line resonator topology with intrinsic balanced performance in magnitude and phase performance is presented. The proposed wideband balun filter consists of four uniform half‐wavelength slot‐line resonators (SLRs) in middle, one single‐ended unbalanced port, and one balanced port with two terminals. By utilizing the distinct field conversion from the slotline to the microstrip line feeding line, the proposed technique can realize good balanced performance inherently in magnitude and phase over a wideband frequency range. In order to demonstrate the proposed scheme and support the design conception, one circuit prototype is designed, fabricated, and tested. All of the measured results of the frequency response, magnitude, and phase imbalance performance agree well with the simulated one, and these results have effectively demonstrated its good filtering property, intrinsic balanced performance in magnitude and phase over a wide band frequency.     

Analysis and optimization of the unpredictable transmission zero in X‐band filter design

This article focuses on the common problem of uncontrollable transmission zero (TZ) in X‐band filter design. Using uniform impedance rectangular resonator (UIRR) to design an X‐band filter always results in an unpredictable TZ on the low‐frequency side of the passband, which greatly deteriorates the frequency selectivity of the filter performance. Electromagnetic coupling polarity analysis of the UIRR shows that the magnetic crosscoupling between nonadjacent resonators which is opposite to the main coupling plays a major role in the unpredictable TZ. By optimizing the UIRR from the loop structure with a small opening to the folded one, weak couplings between resonators are obtained. A high‐temperature superconducting filter at X‐band using folded UIRR resonator was designed and fabricated with a center frequency of 10.01 GHz and a bandwidth of 58 MHz, and the uncontrollable TZ has been removed successfully from the low‐frequency side of passband. The measured insertion loss is less than 0.4 dB and the return loss is greater than 15 dB.     

Design and optimization of a planar folded substrate integrated waveguide bandpass filter exploiting aggressive space mapping

Substrate integrated waveguide (SIW) is a new structure for microwave transmission. In this paper, a planar folded sixth‐order SIW filter is designed with aggressive space mapping (ASM) algorithm. Its center frequency is 22 GHz, 3 dB bandwidth 1 GHz, and in‐band return loss 22 dB. The filter satisfies design specifications after four iterations, and is fabricated using micro‐electro‐mechanical systems (MEMS) technology with a chip size of 7.5 mm × 8.5 mm × 0.4 mm. Measurement results show that the center frequency of the filter measures at 22.2 GHz, 3 dB bandwidth at 1 GHz, insertion loss at 3.57 dB, return loss at 22 dB and out‐of‐band rejection at 40 dB.     

Recessed ground microstrip line at 60 GHz and its application of band‐pass filter

The effect of finite‐size recessed ground on characteristic features of a microstrip transmission line is investigated and verified experimentally on alumina substrate of height 0.127 mm with ε_r = 9.8 at 60 GHz. A measured characteristic impedance of 238 Ω, effective dielectric constant of 3.09, and attenuation constant of 3.4 Np/m is achieved by using a recessed ground of dimensions (width × depth) 4.5 mm × 0.95 mm, below a 50‐Ω (on conventional ground plane) microstrip line. The effect of recessed ground on lumped equivalent circuit elements of microstrip line discontinuities including series‐gap, open‐end, and step discontinuities is also studied. To show the usefulness of recessed ground microstrip line, a prototype of fifth‐order Chebyshev‐type recessed ground end‐coupled band‐pass filter is designed and fabricated at 60 GHz. The filter exhibits measured insertion loss lower than 2.2 dB and return loss better than 13 dB over 3‐dB passband of 6% centered at 60 GHz. The measured results show good consistency with simulated results and confirm the usefulness of recessed ground plane microstrip line.     

Compact ultra‐wideband bandpass filter with variable notch characteristics based on transversal signal‐interaction concepts

A novel technique is presented to design highly compact microstrip ultra‐wideband (UWB) bandpass filters that exhibit high selectivity quasi‐elliptical response. The design is based on transversal signal‐interaction concepts that enable the inclusion of single or dual notch‐bands within the filter's passband to eliminate interference from other services that coexist within the UWB spectrum. The filter configuration comprises of two transmission paths which include folded T‐shaped stepped impedance resonators (SIRs) that are capacitively coupled with the input/output lines to enable signal transmission. It is shown that by combining the filters of different passband centre frequencies an UWB filter can be realised with either a single‐ or dual‐notch function. The theoretical performance of the filter is corroborated via measurements to confirm that the proposed filter exhibits UWB passband of 123% for a 3 dB fractional bandwidth, a flat group‐delay with maximum variation of less than 0.3 ns, passband insertion loss less than 0.94 dB, high selectivity, a sharp rejection notch‐band with attenuation of ?23 dB, and a good overall out‐of‐band performance. Furthermore, the filter occupies a significantly small area of 94 mm² compared with its classical counterparts. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:549–559, 2014.     

Via‐hole coupled oversized microstrip line and its band‐pass filter application

A simple via‐hole coupled oversized microstrip line filter is proposed and demonstrated in this article. The via‐hole in this case works as an inductor coupling structure whereas the oversized microstrip line resonator has a higher Q‐factor than its conventional counterpart. Full‐wave‐based circuit models of a series of via‐holes embedded in the oversized microstrip line are extracted by using our proposed numerical calibration technique combined with a commercial method‐of‐moments simulator. A simple 3‐pole via‐hole coupled oversized microstrip line filter is designed and fabricated on the basis of the extracted circuit models of via‐holes. Measured results show that the demonstrated filter has a center frequency of 1.853 GHz, a bandwidth of 6.98% and an insertion loss of 1.36 dB. Measured results of the fabricated filter sample are in agreement with its simulated results, showing a good performance of the proposed scheme. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2008.     

Bandwidth‐controllable band‐stop filter using spoof surface plasmon polaritons

This article presents a bandwidth‐controllable band‐stop filter based on spoof surface plasmon polaritons (SSPPs) transmission line in the microwave frequency band. The approach of introducing rectangular slots into the corrugation strips offers a greater degree of flexibility in the SSPPs unit cell design. Meanwhile, the high‐order mode can be pulled to the low frequency segment of interest. The lower and upper edge of the stop band of this filter, therefore, can be controlled independently and conveniently. An equivalent circuit model of this unique unit cell is proposed for analyzing stop band formation and guiding the design of this SSSPs filter. Both numerical simulations and measured results demonstrate excellent stop band performance of the filter. The proposed filter may have potential applications in the SSPPs‐based communication system.     

A compact reconfigurable bandpass/lowpass filter with independent transmission zeros based on generalized NRI metamaterial

This article introduces a new design and analysis of a compact reconfigurable bandpass/lowpass filter based on compact negative refractive index metamaterial transmission line. The filter equivalent circuit has been designed as a cascade of three cells of bisected‐Π/Π configuration. The reconfigurable function was achieved using inserted switches in ON and OFF modes within the cells. The filter works as bandpass when all switches are in ON condition and for lowpass switch‐1 is in OFF and switch‐2 in ON condition. The low pass filter has 3‐dB cutoff frequency of 3.25 GHz with a selectivity of 170 dB/GHz. The bandpass filter is cantered at 3.65 GHz and has a well‐matched pass band with insertion loss of 0.2 dB and wide stop band with two transmission zeros (TZs). The frequency positions of TZs are independently varying with series and shunt loading elements. The filter performance has been validated through circuit model, electromagnetic simulation, and experimental measurements. The electrical size of bandpass filter excluding feed line is 0.22 λ_g × 0.20 λ_g (12 × 11 mm²) at center frequency of 3.65 GHz and for lowpass filter is 0.19 λ_g × 0.18 λ_g at cutoff frequency of 3.25 GHz. The filter can be applied in suitable for different wireless applications.     

A covering Ka‐band two‐way switch filter module using a three‐line and an E‐plane waveguide band‐pass filters

A millimeter‐wave ultrawideband two‐way switch filter module is presented in this article. The switch filter module covers whole Ka‐band (26–40 GHz), and is composed of two wideband band‐pass filters and two monolithic microwave integrated circuit (MMIC) single pole two throw (SP2T) switches. One filter is realized using E‐plane iris waveguide band‐pass filter, and another is realized by a novel 11‐pole three‐line microstrip structure band‐pass filter. Compared with the traditional three‐line filter, the proposed three‐line filter not only retains virtues of the traditional three‐line filter, but also resolves drawbacks of it, which include discontinuities between adjacent sections, many parameters of design, and no effective matching circuits at input/output ports. The developed switch filter module is fabricated using hybrid integrated technology, which has a size of 51 × 26 × 9.8 mm³, and interconnections between MMICs and microstrip are established by bond wires. The fabricated switch filter module exhibits excellent performances: for two different states, the measured insertion loss and return loss are all better than 7 and 10 dB in each pass‐band, respectively. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:305–310, 2015.     

Topology bandpass filters in coplanar strip lines

We report a new bandpass filter on coplanar strip (CPS) lines for RF and microwave applications. The filter is implemented as electrode topology on the CPS electrodes. The topology consists of basic electrode patterns that emulate inductors and capacitors in a two‐port filter section. In the design process, equivalent circuit model is used to identify the initial topology, which is then fine tuned using full wave analysis. The bandpass filter is very compact in size and planar in structure. It does not use quarter‐wavelength sections, vias, or bonding wires. It can be fabricated without incurring additional cost. Bandpass filters for the 2.4 GHz ISM (Industrial, Scientific, and Medical) band were designed, fabricated, and measured. The measurement responses agree well with the full‐wave simulation results. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2008.     

Dual extended composite right/left‐handed transmission line metamaterial

The new concept of dual extended composite right/left‐handed transmission line (D‐ECRLH TL), with 2 right handed and 2 left handed frequency bands is presented. The D‐ECRLH TL and extended composite right/left handed transmission line are structurally dual. Therefore, the proposed TL shows the dual properties of the ECRLH TL. The D‐ECRLH indeed behaves as a dual‐band bandstop filter, in opposition to the ECRLH which is a dual‐band bandpass one. In contrast, the D‐ECRLH creates an unlimited LH bandwidth. In this article, the transmission parameters and the fundamental properties of the D‐ECRLH TL (dispersion and impedance diagrams) are investigated. The results show that the proposed structure is suitable to design the quad‐band microwave circuits and systems. A prototype of the proposed D‐ECRLH unit cell is realized by the microstrip technology. The good agreement between the measurement and simulation results confirms the realizability of the proposed structure.