A novel RF energy harvesting cube based on air dielectric antenna arrays

In this article, a new 2 × 2 circular microstrip antenna array with air dielectric layer for ambient RF energy harvesting has been proposed. Two pairs of arc‐shaped slots located close to the boundary of the circular microstrip patch have been designed for achieving dual‐band response and extending the frequency bandwidth. The antenna has a frequency bandwidth from 1.85 to 1.93 GHz and from 2.0 to 2.1 GHz which can cover GSM‐1800 and UMTS‐2100 bands. At the frequency of 1.89 and 2.05 GHz, the measured gain is 5.3 and 6.6 dBi, respectively, and high gain of 3.8‐9.3 dBi has been achieved over the whole band. Also, a broadband rectifier that can cover all the bandwidths of the antenna array is designed for the rectenna, which has the maximum rectifying efficiency of 53.6%. Finally, a cube device formed of four antenna and four rectifiers is designed to harvest RF energy, whose maximum output DC voltage is 2.3 V and the maximum output power is 4 mW that can drive four LEDs and an electronic watch.     

A compact UWB‐MIMO with dual grounded CRR for isolation improvement

In this article, a compact half‐hexagonal ultra‐wide band multiple‐input‐multiple‐output (MIMO) antenna is presented. The key feature of the antenna is its novel isolation improvement technique which includes grounded stub along with dual grounded circular ring resonator. The antenna contains two counter facing half‐hexagonal monopoles having hybrid isolation circuit. The antenna has a compact size of 20 × 34 mm², with operating frequency band of 3‐11 GHz where port isolation is better than 20 dB in most of the band. The MIMO performance is ensured by calculating envelop correlation coefficient and mean effective gain ratio for isotropic, indoor, and outdoor environment. The performance of the antenna with multilayer printed circuit board having large dual ground plane and device housing is also studied. Results show that the proposed MIMO antenna is a good candidate for handheld devices for wireless personal‐area networks application.     

Dual‐band aperture‐coupled rectenna for radio frequency energy harvesting

The article presents a dual‐band aperture‐coupled rectenna for radio frequency (RF) energy harvesting at 2.45 and 5 GHz application. The rectenna consists of a dual‐band π‐shaped slot‐etched aperture‐coupled antenna, designed at the lower substrate of two FR4 substrate layers and a dual‐band rectifier. The proposed antenna design also introduces the harmonic suppression of third‐ and higher order harmonics, ranging from 6 up to 10 GHz from the asymmetrical stubs design at the transmission feedline. The dual‐band rectifier is designed to operate at 2.45 and 5 GHz frequency, successfully achieving high conversion efficiency at 68.83% and 49.90% with the optimum load resistor of value 700 Ω and 1.1 kΩ. The minimum DC voltage of 0.167 and 0.236 V with 0 dBm RF input power can be increased when greater RF power is being applied to it, increasing its flexibility to cater various low‐power applications.     

A compact planar inverted‐F antenna with U‐shaped strip for all‐metal‐shell handset application

A compact dual‐band planar inverted‐F antenna (PIFA) with U‐shaped strip is proposed in this work for all‐metal‐shell mobile telephone application. As metal‐shell handsets are getting more and more popular nowadays, it raises a big challenge in antenna design as the metal‐shell associated with surrounding electronic components like front‐back‐cameras and telephone receiver would affect the antenna performance. This work provides an optional solution to alleviate this problem, where the metal shell of the handset and a U‐shaped strip are utilized as part of the antenna. The proposed antenna is able to generate radiation at 2.4 GHz for Wi‐Fi application with the help of the metal shell while using the U‐shaped strip can achieve a resonance at 1.575 GHz for GPS application. A prototype has been fabricated to verify the radiation performance in a practical handset test environment.     

A modified fractal‐shaped slotted patch antenna with defected ground using metasurface for dual band applications

A novel modified fractal‐shaped slotted patch antenna employing metasurface at bottom plane along with partial ground has been proposed in this work for dual band applications with significant gain. A 4 × 5 order metasurface has been formed in the ground plane by introducing a periodic combination of two L‐type patches with centered C‐type shaped patch. The top conductor and the ground plane are designed on a 1.6 mm thick FR4 dielectric with the dimension of 28 × 28 mm². The antenna is designed in such a way that it operates over the dual frequency ranges viz., 1.80 to 5.70 GHz and 10.38 to 10.94 GHz. The maximum return loss of 21 dB has been achieved over 2.60 GHz while the maximum realized gain of 7.16 dBi has been obtained at 10.92 GHz. The designed antenna offers omnidirectional radiation characteristics in the first band while directional radiation characteristics have been observed in the second band. The proposed antenna can be utilized for WiMAX 3.5/5.5 GHz, mobile, radio astronomy, and microimaging in medical analysis.     

CPW fed miniaturized dual‐band short‐ended metamaterial antenna using modified split‐ring resonator for wireless application

A miniaturized dual‐band metamaterial (MTM) antenna has been designed in this article. The designed coplanar waveguide fed antenna has composed of inner split‐ring resonator and an outer open ring resonator with rectangular stub. The series parameter of the antenna is used to determine the zeroth order resonance frequency due to short‐ended boundary condition. The whole size of proposed structure is 20 × 25.5 mm². This MTM antenna exhibits dual‐band operation at 3.17 GHz (3.1–3.22 GHz) and 5.39 GHz (5.27–5.47 GHz). The proposed MTM structure achieves measured peak gain of 0.71 and 1.89 dB at 3.17 and 5.39 GHz, respectively. The proposed antenna can be used for recent radio communication in form of S‐band application and Wi‐MAX.     

A dual‐band case‐printed planar inverted‐F antenna design with independent resonance control for wearable short range telemetric systems

In this article, a novel 3D meandered planar inverted‐F antenna (PIFA) is proposed for dual band application targeting Wireless Body Area Network (WBAN). The proposed antenna is printed on the casing of a 3D‐base‐station model having a size of 88 × 95 × 10.2 mm³. The proposed PIFA covers two bands including medical implant communication service (MICS) (402‐405 MHz), as well as the industrial, scientific, and medical (ISM) (2.4‐2.48 GHz) bands. Each of the two bands can be controlled independently. The 3D configuration contains two linked meandered resonators to downsize the structure. Due to its conformal shape, omnidirectional radiation pattern, and low‐profile nature, the proposed PIFA is a potential candidate for targeting the WBAN applications. The proposed antenna, covering the MICS and ISM bands, works with an optimally matching (VSWR<2) at the aforementioned bands. The design concept was validated by fabricating the antenna prototype and measuring its characteristics.     

Dual‐band dual‐polarized compact planar monopole antenna for wide axial ratio bandwidth application

In this article, a geometrically simple, microstrip line‐fed planar monopole structure with slanting edge ground plane is designed to realize the dual‐band dual‐polarized operation. The proposed antenna consists of a rotated U‐shaped patch and an electromagnetically coupled L‐shaped parasitic radiating element. Owing to the combination of microstrip line‐fed radiating patch and a slanting‐edge rectangular ground plane on the opposite side of the substrate, the proposed dual‐band antenna can generate broad axial ratio bandwidth (ARBW) in the upper frequency band. The overall dimension of the prototype is only 32 × 32 × 1.6 mm³. The measured results validate that the proposed antenna has two operational frequency bands, 29.84% (1.54‐2.08 GHz) for linearly polarized radiation and 71.85% (3.96‐8.4 GHz) for circularly polarized radiation. Measured result shows that 3‐dB ARBW of the proposed antenna is 73.54% (3.80‐8.22 GHz) in the higher frequency band. It shows that the higher frequency band exhibits a left‐hand circularly polarized radiation in the boresight direction.     

Frequency tunable circularly polarized antenna with branch line coupler feed network for wireless applications

In this article, frequency tuning and circularly polarized concentric circular microstrip antenna is investigated. The proposed antenna consist of varactor diode for frequency tuning and branch line coupler (BLC) feed network to achieve the circular polarization (RHCP/LHCP). By changing the varactor diode capacitance between 12.33 pF (0 V) to 1.30 pF (15 V) attain the frequency tuning (2.34‐2.68 GHz). The right hand circular polarization (RHCP) and left hand circular polarizations (LHCP) are realized in the antenna through BLC feed network output ports. The impedance bandwidth (2.05‐3.13 GHz) of BLC feed network is well‐matched with the circular microstrip antenna frequency tunable bandwidth. The proposed antenna is fabricated, and simulated results are verified using the mathematical modeling and experimental verification.     

Novel offset‐fed dual‐band aperture‐dipole composite antenna: Operating principle and design approach

Operating principle and design approach of a novel dual‐band aperture‐dipole composite antenna are proposed. It is shown that multiple operating modes can be simultaneously excited by employing offset‐feeding technique at first. After the behavior of each mode is studied, the operating principle of the antenna is analyzed and described. Then, an improved dual‐band aperture‐dipole composite antenna is formed and it is designed by using the proposed approach. The antenna is experimentally verified. It is demonstrated that two operating bands for radiation are ranged from 2.36 to 2.58 GHz and from 4.1 to 15.72 GHz, respectively, in which the reflection coefficient are both 相似文献   

Gain enhanced multipattern reconfigurable antenna for vehicular communications

This article presents the design and implementation of a high‐gain tunable dual‐band pattern reconfigurable antenna for vehicular communications. The proposed antenna consists of a slotted patch loaded with a double‐side FSS acting as superstrate. The proposed slotted antenna operates at 2.45 and 3.5 GHz and the frequency tuning over the dual‐band is accomplished by employing a varactor diode for tuning the center frequency from 2.41 to 2.62 GHz and from 3.38 to 3.65 GHz at lower and upper frequency bands, respectively. To obtain pattern reconfiguration, the slotted patch is divided into four regions by using two diagonal lines of vias. By properly choosing the excitation port combinations, 14 different radiation patterns are realized with a maximum realized gain of 8.4 and 7.9 dB. Further enhancement of gain is achieved using frequency‐selective surface (FSS) screens which act as a partially reflecting surface. The unique feature of this design is to provide reflection coefficient with high reflectivity in two predetermined frequency ranges. The prototype antenna is fabricated and the measurement results are reported. The experimental results show that the prototype antenna with FSS offers tunable dual‐band with beam reconfigurable properties.     

Compact dual ports handheld RFID reader antenna with high isolation

A compact dual ports antenna with high isolation is proposed for handheld radio frequency identification (RFID) reader, which is rarely reported in open literatures. Different with conventional handheld RFID reader antenna with single port, the proposed antenna transmits and receives signal separately. The proposed antenna operating with full duplex mode can enhance effectively sensitivity of reader, as the strong transmitting signal of reader with single port is usually highly coupled with weak receiving backscatter signal of tag. The antenna utilizes aperture coupled patch structure that occupies less volume and provides further space‐saving efficiency. The height of the proposed antenna is only 5.1 mm and the volume of that is 80 ×80 × 5.1 mm³, which is easy to integrate in handheld RFID readers. The antenna uses four symmetric coupling apertures to excite two orthogonal modes for dual polarized operation. High isolation of around ?35 dB is obtained by proper arrangement of the length and position of the coupling apertures. The maximum measured return loss is ?39 dB at 2.4 GHz and isolation is ?47 dB at 2.4 GHz. The antenna is suitable for applications in handheld RFID readers. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:548–555, 2015.     

Dual‐polarized high gain resonant cavity antenna for radio frequency energy harvesting

A Fabry pérot antenna with a multilayer superstrate having nonuniform unit cells has been investigated as a receiving antenna for radio frequency (RF) energy harvesting applications. Here, the primary radiator is selected as a dual‐polarized aperture coupled microstrip antenna with a double‐layer superstrate. This antenna excites orthogonal polarizations, vertical (V) and horizontal (H) in the frequency band of 6.2 and 5.8 GHz, respectively, due to the presence of two orthogonal H‐shaped slots in its ground plane. The proposed antenna provides a gain enhancement of 9.8 and 10.1 dBi at the respective frequencies. The rectifying circuit is designed for a frequency of 5.8 GHz using a voltage doubler topology. The circuit provides a power conversion efficiency of 41% at 0 dBm input power.     

Dual‐band beam scanning filtering antenna using dual‐eighth mode substrate integrated waveguide‐based metamaterial structure

In this article, a dual‐band beam scanning antenna with filtering capability is proposed by using novel dual‐eighth mode substrate integrated waveguide‐based dual‐band metamaterial (DB‐MTM) structure. The novel DB‐MTM structure consists of two interconnected modified eighth mode substrate integrated waveguide (EMSIW) structures, which is designed by etching four interdigital fingers on the upper ground, and has two balanced composite right/left‐handed (CRLH) passbands. Taking advantage of the continuous phase constant changing from negative to positive values within the two CRLH passbands of the DB‐MTM structure, a beam scanning antenna, which is composed of 11 dB‐MTM unit cells, is designed to achieve continuous beam scanning from backward to forward directions within dual operating frequency bands. For verification, the proposed dual‐band antenna is fabricated and measured. According to the measurements, the fabricated antenna can scan its main beam from ?72° to +57° and ?70° to +38° over the two operating frequency bands of 3.40‐4.95 GHz and 5.85‐6.80 GHz, respectively; and exhibits very sharp transitions at the band edges over the two operating frequency bands. Besides, the measured peak gains in the two operating bands are 14.0 dB at 4.5 GHz and 14.5 dB at 6.4 GHz. Moreover, the measurements show good agreement with the simulations, proving the validity of the design method, and further expanding the applications of EMSIW.     

Dual‐band dual‐sense circularly polarized antenna based on crossed dipole structure for WLAN/WiMAX applications

This paper presents a new approach to design dual‐band antenna with dual‐sense circularly polarized (CP) operation. A principle for CP radiation is the use of two orthogonal dipoles and properly choosing their lengths can produce either right‐hand CP (RHCP) or left‐hand CP (LHCP) operation. In the proposed structure, the lower frequency band at 2.4 GHz is designed with RHCP radiation and LHCP is the operating mode of the higher band at 3.5 GHz. For verification, an antenna prototype is fabricated and measured. Measured data indicate that good performances over the RHCP and LHCP bands can be obtained with usable bandwidths of 2.9% (2.36‐2.43 GHz) and 1.7% (3.48‐3.54 GHz). Along with this, it also observes good unidirectional radiation patterns and the measured broadside gains are around 7.7 and 7.4 dBic across these frequency ranges.     

Design of a microstrip fed printed monopole antenna for bluetooth and UWB applications with WLAN notch band characteristics

In this article, a microstrip fed printed dual band antenna for Bluetooth (2.4–2.484 GHz) and ultra‐wide band (UWB; 3.1–10.6 GHz) applications with wireless local area network (WLAN; 5.15–5.825 GHZ) band‐notch characteristics is proposed. The desired dual band characteristic is obtained by using a spanner shape monopole with rectangular strip radiating patch, whereas the band‐notch characteristics is created by a mushroom‐like structure. The Bluetooth and notch bands can easily be controlled by the geometric parameters of the rectangular strip and mushroom structure, respectively. The proposed antenna has been designed, fabricated, and tested. It is found that the proposed antenna yields both the Bluetooth and UWB performance in the frequency regions of 2.438 to 2.495 GHz and 3.10 to 10.66 GHz, respectively for |S₁₁| ≤ ?10 dB with an excellent rejection band of 5.14 to 5.823 GHz to prevent WLAN signals. The experimental results provide good agreement with simulated ones. Surface current distributions are used to analyze the effects of the rectangular strip and mushroom. The designed antenna exhibits nearly omnidirectional radiation patterns, stable gain along with almost constant group delay over the desired bands. Hence, the proposed antenna is expected to be suitable for both Bluetooth and UWB applications removing the WLAN band. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:66–74, 2015.     

Compact high isolation wideband 4G and 5G multi‐input multi‐output antenna system for handheld and internet of things applications

This article presents a compact wideband multi‐input multi‐output (MIMO) antenna with a high port‐to‐port isolation, having a height h = 3.5 mm for 4G, 5G, and Internet of things (IoT) applications. Two identical planar inverted‐F antennas (PIFA) are used in this antenna system. For achieving wideband characteristics, closed‐ended and open‐ended rectangular slots are etched out on top plate of each PIFA, whereas a slot is etched in ground plane under the top plate of each PIFA. For achieving high isolation, a rectangular slot is etched out in the center of ground plane between two PIFAs. For further reduction in mutual coupling, a small rectangular strip is connected between the top plates of two PIFAs that introduce an antiresonance for enhancing isolation between two PIFA elements. The minimum isolation obtained between the ports of the two PIFAs is about ?20 dB. The minimum impedance bandwidth obtained by the two PIFAs is from 2 to around 3.6 GHz, thus become a wide band antenna covering WLAN band (2.45GHz), 4G‐LTE bands, WiMAX bands (IMT‐2.1 GHz, IMT‐2.3 GHz, and IMT‐E 2.6 GHz), and a sub‐6 GHz 5G band (3.4‐3.6 GHz). The simulated results are compared with the measured ones that are generally found in good agreement. Being low profile and compact, this antenna can be used for advanced 5G communication systems and IoT devices.     

A CPW‐fed UWB MIMO antenna with integrated GSM band and dual band notches

This article presents a coplanar waveguide fed global system for mobile communications band integrated ultra wide band (UWB) multiple input multiple output (MIMO) antenna with single and dual notch band characteristics. The novelty of the antenna lies in its design as all the unit cells of the proposed UWB MIMO antenna structure are orthogonal to each other therefore the additional isolation elements responsible for achieving high isolation are not required consequently making proposed antenna design simple and easy to fabricate. In this context, 2 MIMO systems have been designed. The first MIMO system is consisting of a dual port antenna whereas the second MIMO system is a printed quad port antenna; further single and dual notch band are achieved in the proposed multi‐port MIMO antenna. The antenna shows pattern diversity throughout the impedance bandwidth range. The gain of the antenna varies from 4 to 8.48 dBi. The 2 band notches are achieved at 4.8 and 7.7 GHz in the UWB range. The proposed antenna is fabricated and it is found measured results are in good agreement with simulated results.     

Three‐dimensional printed wideband,dual‐cavity Ku‐band antenna

A novel three‐dimensional (3D) printed, wideband, and low cost bull's eye antenna is proposed and designed for Ku‐band applications. The proposed antenna covers entire Ku‐band satellite communication bands starting from 10.5 GHz to 14.5 GHz. The antenna structure consists of dual‐cavity radiating aperture surrounded by a circular groove. With the addition of cavity and corrugation, the antenna gain is increased more than 6 dB. The antenna is fabricated using 3D printing technology and conductive painting. Measurement results indicate that the antenna has 72% fractional bandwidth from 8 GHz to 17 GHz. Measured antenna peak gain is 13.5 dBi at 13 GHz and no less than 11.5 dBi throughout the entire Ku band.