Spectroelectrochemical sensing based on multimode selectivity simultaneously achievable in a single device. 16. Sensing by fluorescence

A fluorescence spectroelectrochemical sensor capable of detecting very low concentrations of metal complexes is described. The sensor is based on a novel spectroelectrochemical sensor that incorporates multiple internal reflection spectroscopy at an optically transparent electrode (OTE) coated with a selective film to enhance detection limits by preconcentrating the analyte at the OTE surface. Nafion was used as the selective cation exchange film for detecting Ru(bpy)(3)(2+), the model analyte, which fluoresces at 605 nm when excited with a 441.6-nm HeCd laser. The unoptimized linear dynamic range of the sensor for Ru(bpy)(3)(2+) is between 1 x 10(-)(11) and 1 x 10(-)(7) M with a calculated 2 x 10(-)(13) M detection limit. The sensor employs extremely thin films ( approximately 12 nm) without significantly sacrificing its sensitivity. The sensor response is demonstrated with varying film thicknesses. A state-of-the-art flow cell design allows variable cell volumes as low as approximately 4 microL. Fluorescence of the sample can be controlled by electromodulation between 0.7 and 1.3 V. Sensor operation is not reversible for the chosen model film (Nafion) and sample (Ru(bpy)(3)(2+)) but it can be regenerated with ethanol for multiple uses.     

Optically transparent diamond electrode for use in ir transmission spectroelectrochemical measurements

A new analytical spectroelectrochemical methodology is reported on that utilizes an optically transparent boron-doped diamond thin film. The film was deposited on undoped Si by microwave-assisted chemical vapor deposition using a 4-h growth with a 0.5% CH4/H2 source gas mixture and 2 ppm B2H6 added for boron doping. The thin-film electrode possessed a transparency of 40-60% in the mid- and far-IR regions of the electromagnetic spectrum. The physical, electrical, optical, and electrochemical properties of the electrode were characterized by scanning electron microscopy, Raman spectroscopy, X-ray diffraction, four-point probe electrical resistance measurements, IR spectroscopy, and cyclic voltammetry. The film's electrochemical behavior was evaluated using both aqueous (Fe(CN)(6)3-/4-, methyl viologen, Ru(NH3)(6)3+/2+, and IrCl(6)2-/3-) and nonaqueous (ferrocene) redox systems. The film exhibited a low and stable background current and a nearly reversible voltammetric response for all these redox systems. The diamond/Si optically transparent electrode (OTE) and a thin-layer transmission cell were used to record the spectroelectrochemical response for 10 mM Fe(CN)(6)3-/4- in 1 M KCl. Difference IR spectra (oxidized minus reduced), recorded at various applied potentials, showed that the CN vibrational mode at 2039 cm-1 for Fe(CN)(6)4- reversibly shifted to 2116 cm-1 upon oxidation to Fe(CN)(6)3-, as expected. Difference IR spectra (oxidized minus reduced) were also recorded for 20 mM ferrocene in 0.1 M TBABF4/CH3CN. A shift of the C-H bending mode of the cyclopentadienyl ring from 823 to 857 cm-1 occurred upon oxidation of ferrocene to ferricenium. The key finding from the work is that the diamond OTE provides sensitive, reproducible, and stable spectroelectrochemical responses for aqueous and nonaqueous redox systems in the mid- and far-IR.     

Determination of Dansyl Amino Acids and Oxalate by HPLC with Electrogenerated Chemiluminescence Detection Using Tris(2,2'-bipyridyl)ruthenium(II) in the Mobile Phase

A new electrogenerated chemiluminescence detection method is investigated for use in detection in reversed-phase and reversed-phase ion-pair HPLC with Ru(bpy)(3)(2+) in the mobile phase. In this method, different concentrations of Ru(bpy)(3)(2+) are dissolved in the mobile phase and the HPLC column flushed with the mobile phase for 1 h until the column is saturated with Ru(bpy)(3)(2+). The separated analytes along with Ru(bpy)(3)(2+) pass through an optical-electrochemical flow cell which has a dual platinum electrode held at a potential of 1250 mV vs a Ag/AgCl reference electrode. On the surface of the electrode, Ru(bpy)(3)(2+) is oxidized to Ru(bpy)(3)(3+) which reacts with the analytes to emit light. The retention times, retention orders, detection limits, and linearity in working curves are compared to those obtained with the conventional postcolumn Ru(bpy)(3)(2+) addition method. The retention times for dansyl amino acids with Ru(bpy)(3)(2+) in the mobile phase are longer than those obtained with the postcolumn addition approach. This may be caused by π-to-π interactions between the aromatic groups of the dansyl derivatives and the bipyridyl groups of Ru(bpy)(3)(2+) in the Ru(bpy)(3)(2+)-saturated reversed-phase column. Similarly, oxalate is separated from urine and blood plasma samples by reversed-phase ion-pair HPLC. Plasma samples are obtained using ultrafiltration to remove proteins from whole blood. Retention times for oxalate with the two detection techniques are identical, and detection limits for these techniques are compared.     

A two-channel microfluidic sensor that uses anodic electrogenerated chemiluminescence as a photonic reporter of cathodic redox reactions

This paper describes a new approach for sensing electrochemically active substrates in microfluidic systems. This two-electrode sensor relies on electrochemical detection at one electrode and electrogenerated chemiluminescent (ECL) reporting at the other. Each microfabricated indium tin oxide electrode is located in a separate microfluidic channel, but the channels are connected downstream of the electrodes to maintain a complete electrical circuit. Because of laminar flow, there is no bulk mixing of the fluids in the detecting and reporting channels. This approach allows the ECL reaction to be physically and chemically decoupled from the sensing channel of the device, which greatly expands the number of analytes that can be detected. However, because the cathode and anode are connected, electron-transfer processes occurring at the sensing electrode are electrically coupled to the ECL reaction. Charge balance permits the ECL light output to be quantitatively correlated to electrochemical reductions at the cathode. The system is used to detect Fe(CN)6(3-), Ru(NH3)6(3+), and benzyl viologen and report their presence via Ru(bpy)3(2+) (bpy = bipyridine) luminescence. Each different redox target initiates ECL at a unique potential bias related to its standard redox potential. The influence of the concentrations of Ru(bpy)3(2+) and the target analytes is discussed.     

Large-amplitude Fourier transformed high-harmonic alternating current cyclic voltammetry: kinetic discrimination of interfering Faradaic processes at glassy carbon and at boron-doped diamond electrodes

Significant advantages of Fourier transformed large-amplitude ac higher (second to eighth) harmonics relative to responses obtained with conventional small-amplitude ac or dc cyclic voltammetric methods have been demonstrated with respect to (i) the suppression of capacitive background currents, (ii) the separation of the reversible reduction of [Ru(NH(3))(6)](3+) from the overlapping irreversible oxygen reduction process under conditions where aerobic oxygen remains present in the electrochemical cell, and (iii) the kinetic resolution of the reversible [Ru(NH(3))(6)](3+/2+) process in mixtures of [Fe(CN)(6)](3-) and [Ru(NH(3))(6)](3+) at appropriately treated boron-doped diamond electrodes, even when highly unfavorable [Fe(CN)(6)](3-) to [Ru(NH(3))(6)](3+) concentration ratios are employed. Theoretical support for the basis of kinetic discrimination in large-amplitude higher harmonic ac cyclic voltammetry is provided.     

A single calibration graph for the direct determination of ascorbic and dehydroascorbic acids by electrogenerated luminescence based on Ru(bpy)(3)2+ in aqueous solution

Ascorbic (H2A) and dehydroascorbic (DA) acids were for the first time directly determined in a single chromatographic run by means of the tris(2,2'-bipyridine)ruthenium(II) (Ru(bpy)(3)2+) based electrogenerated chemiluminescence (ECL) detection. For the first time, it was demonstrated that DA, a nonelectroactive compound, is ECL active and is responsible for the ECL behavior of H2A. This fact, together with the lack of a DA standard, suggested the use of a calibration graph obtained for H2A, for determining both analytes. The proven ECL activity of DA, together with literature data relative to the standard redox potentials of the different species coming from H2A, led to a reconsideration of the proposed ECL reaction mechanism for H2A. The role of the OH- ion in the reaction mechanism of the two analytes appeared to be crucial. H2A and DA could be separated by a suitable C18-reversed-phase HPLC column using an aqueous 30 mM H3PO4 solution as the mobile phase. The optimal ECL response was achieved by polarizing the working electrode at 1.150 Vvs SCE (standard calomel electrode) (oxidation diffusion limiting potential for both H2A and Ru(bpy)(3)2+). The Ru(bpy)(3)2+ solution, at pH 10 for carbonate buffer, was mixed to the eluent solution in a postcolumn system, obtaining, still at pH 10, the final 0.25 mM Ru(bpy)(3)2+ concentration. The detection limit found for the two analytes was 1 x 10(-7) M. The method was successfully applied to the determination of the analytes in a commercially available orange fruit juice.     

Bioinorganic composites for enzyme electrodes

Sparingly soluble redox salts were combined with a model enzyme, glucose oxidase, in a host matrix of a biopolymer chitosan to form bioinorganic composite films on the surface of glassy carbon electrodes. Four redox salts, each containing the Ru(NH3)6(3+) cation and a selected anion, such as Ru(CN)6(4-), Fe(CN)6(4-), Co(CN)6(3-) or IrCl6(3-), were studied. The composition and catalytic properties of such composite materials toward glucose oxidation were investigated by spectroscopic and electrochemical methods. The composite films provided an oxygen-independent electrical communication between the enzyme's redox centers and a glassy carbon surface at a potential as low as -0.10 V vs Ag/AgCl(3 M Cl-). The nature of the electrical communication is discussed in terms of redox mediation by the Ru(NH3)6(3+)-containing ion pairs formed inside the biocomposites. The kinetic significance of the mediator's charge is considered by postulating that neutral ion pairs are more efficient redox mediators of the enzymatic reaction than those negatively charged. The low operating potential of enzyme electrodes based on the bioinorganic composites allows for an interference-free determination of glucose. The design of the biocomposites is generic and can incorporate oxidoreductase enzymes other than glucose oxidase to provide a host of biosensors for biologically and environmentally important analytes.     

Spectroelectrochemical sensing based on multimode selectivity simultaneously achievable in a single device. 17. Improvement in detection limits using ultrathin perfluorosulfonated ionomer films in conjunction with continuous sample flow

We report herein an attenuated total reflectance (ATR) absorbance-based spectroelectrochemical sensor for tris(2,2'-bipyridyl)ruthenium(II) ion [Ru(bpy)(3)(2+)] that employs ultrathin (24-50 nm) Nafion films as the charge-selective layer. This film serves to sequester and preconcentrate the analyte at the optically transparent electrode surface such that it can be efficiently detected optically via electrochemical modulation. Our studies indicate that use of ultrathin films in tandem with continuous flow of sample solution through the cell compartment leads to a 100-500-fold enhancement in detection limit (10 nM) compared to earlier absorbance-based spectroelectrochemical sensors ( approximately 1-5 microM); markedly shorter analysis times also result. We report the dependence of the measured absorbance on sample flow rate and Nafion film thickness, and also provide calibration curves that illustrate the linear range and detection limits of the sensor using a 24 nm film at a constant sample flow rate of 0.07 mL/min.     

Chromatographic detection of nitroaromatic and nitramine compounds by electrochemical reduction combined with photoluminescence following electron transfer

The oxidizing agent tris(bipyridyl)ruthenium(III), or Ru-(bpy)(3)3+, is used as a postcolumn reagent for the detection of nitroaromatic and nitramine explosive compounds. After separation, the explosives are reduced electrochemically to oxidizable products such as hydroxlamines and nitrosamines, and these products react readily with Ru-(bpy)(3)3+ and Ru(bpy)(3)2+. The photoluminescence from the latter is used for detection. A porous carbon electrode was used for on-line analyte reduction following chromatography. Another porous carbon electrode was used to generate the nonluminescent Ru(bpy)(3)3+ from Ru(bpy)(3)3+ on-line at high efficiency. The two streams were combined, and the Ru(bpy)(3)2+ produced by oxidation of the reduced analytes was detected by laser illumination and light detection. Reductive hydrodynamic voltammograms of nitrobenzene, 2,4,6-trinitrotoluene, and hexahydro-1,3,5-trinitro-1,3,5-triazine indicated that a potential of - 1500 mV vs Ag/AgCl was sufficient to achieve a maximum signal from the reduced analytes. HPLC with a water/acetonitrile gradient on a C-18 reversed-phase column was then used to determine these three compounds plus the four additional examples, 1,3,5,7-tetrazocine, 2,4-dinitrotoluene; 2,6-dinitrotoluene, and 4-nitrotoluene. For both hydrodynamic voltammetry and HPLC detection, the photoluminescence following electron-transfer signal was calibrated using the one-electron standards ferrocene and ferrocenecarboxylic acid. Detection limits were in the low-nanomolar range for 20-microL injections of nonpreconcentrated nitro compounds.     

Chemiluminescence detection using regenerable tris(2,2'-bipyridyl)ruthenium(II) immobilized in Nafion.

The development of a detection method based on the electrogenerated chemiluminescence of tris(2,2'-bipyridine)ruthenium(II), (Ru(bpy)3(2+], immobilized in a Nafion film coated on an electrode is discussed. Control of the electrode potential controls creation of the reactive reagent Ru(bpy)3(3+) which reacts with certain analytes to yield chemiluminescence emission of intensity proportional to the analyte concentration. The reaction results in Ru(bpy)3(3+) being converted to Ru(bpy)3(2+), which then is recycled to Ru(bpy)3(3+) again at the electrode. This sensor has been used in flow injection to determine oxalate, alkylamines, and NADH. Detection limits are 1 microM, 10 nM, and 1 microM, respectively, with working ranges extending over 4 decades in concentration. Sensitivity is constant over the wide pH range from 3 to 10. With oxalate, and to a small extent with amines, emission intensities increase with increasing ionic strength; this was shown to be a phenomenon related to the Nafion film and not to the chemiluminescence reaction. Emission intensities increase with temperature. The sensor remains stable for several days with suitable storage conditions. Significant amounts of Ru(bpy)3(3+) are shown to be capable of storage within the film.     

Electrochemiluminescent detection of metal cations using a ruthenium(II) bipyridyl complex containing a crown ether moiety

The effects of metal ions on the electrochemiluminescence (ECL) properties of (bpy)2Ru(AZA-bpy) (bpy = 2,2'-bipyridine; AZA-bpy = 4-(N-aza-18-crown-6-methyl-2,2'-bipyridine) have been investigated. The electrochemistry, photophysics and ECL of Ru(bpy)3(2+) in the presence of Pb2+, Hg2+, Cu2+, and K+ are reported. The anodic oxidation of Ru(bpy)3(2+) produces ECL in the presence of tri-n-propylamine (TPrA) in 50:50 (v/v) CH3CN:H2O solution. Increases in ECL efficiency (photons generated per redox event) up to 20-fold that depend on both the concentration and nature of the metal ion have been observed, making this an interesting system for electrochemiluminescence metal ion sensing.     

Electrochemical performance of diamond thin-film electrodes from different commercial sources

The electrochemical properties of two commercial (Condias, Sumitomo) boron-doped diamond thin-film electrodes were compared with those of two types of boron-doped diamond thin film deposited in our laboratory (microcrystalline, nanocrystalline). Scanning electron microscopy and Raman spectroscopy were used to characterize the electrode morphology and microstructure, respectively. Cyclic voltammetry was used to study the electrochemical response, with five different redox systems serving as probes (Fe(CN)(6)(3)(-)(/4)(-), Ru(NH(3))(6)(3+/)(2+), IrCl(6)(2)(-)(/3)(-), 4-methylcatechol, Fe(3+/2+)). The response for the different systems was quite reproducibile from electrode type to type and from film to film for electrodes of the same type. For all five redox systems, the forward reaction peak current varied linearly with the scan rate(1/2) (nu), indicative of electrode reaction kinetics controlled by mass transport (semi-infinite linear diffusion) of the reactant. Apparent heterogeneous electron-transfer rate constants, k degrees (app), for all five redox systems were determined from deltaE(p)-nu experimental data, according to the method described by Nicholson (Nicholson, R. S. Anal. Chem. 1965, 37, 1351.). The rate constants were also verified through digital simulation (DigiSim 3.03) of the voltammetric i-E curves at different scan rates. Good fits between the experimental and simulated voltammograms were found for scan rates up to 50 V/s. k degrees (app) values of 0.05-0.5 cm/s were observed for Fe(CN)(6)(3)(-)(/4)(-), Ru(NH(3))(6)(3+/2+), and IrCl(6)(2)(-)(/3)(-) without any extensive electrode pretreatment (e.g., polishing). Lower k degrees (app) values of 10(-)(4)-10(-)(6) cm/s were found for 4-methylcatechol and Fe(3+/2+). The voltammetric responses for Fe(CN)(6)(3)(-)(/4)(-) and Ru(NH(3))(6)(3+/2+) were also examined at all four electrode types at two different solution pH (1.90, 7.35). Since the hydrogen-terminated diamond surfaces contain few, if any, ionizable carbon-oxygen functionalities (e.g., carboxylic acid, pK(a) approximately 4.5), the deltaE(p), i(p)(ox), and i(p)(red) values for the two systems were, for the most part, unaffected by the solution pH. This is in contrast to the typical behavior of oxygenated, sp(2) carbon electrodes, such as glassy carbon.     

Enhanced electrogenerated chemiluminescence in the presence of fluorinated alcohols

The electrochemistry, UV-vis absorption, photoluminescence (PL), and coreactant electrogenerated chemiluminescence (ECL) of Ru(bpy)3(2+) (where bpy=2,2'-bipyridine) have been obtained in a series of hydroxylic solvents. The solvents included fluorinated and nonfluorinated alcohols and alcohol/water mixtures. Tri-n-propylamine was used as the oxidative-reductive ECL coreactant. Blue shifts of up to 30 nm in PL emission wavelength maximums are observed compared to a Ru(bpy)3(2+)/H2O standard due to interactions of the polar excited state (i.e., *Ru(bpy)3(2+)) with the solvent media. For example, Ru(bpy)3(2+) in water has an emission maximum of 599 nm while in the more polar hexafluoropropanol and trifluoroethanol it is 562 and 571 nm, respectively. ECL spectra are similar to PL spectra, indicating the same excited state is formed in both experiments. The difference between the electrochemically reversible oxidation (Ru(bpy)3(2+/3+)) and first reduction (Ru(bpy)2(2+/1+)) correlates well with the energy gap observed in the luminescence experiments. Although the ECL is linear in all solvents with [Ru(bpy)3(2+)] ranging from 100 to 0.1 nm, little correlation between the polarity of the solvent and the ECL efficiency (phiecl=number of photons per redox event) was observed. However, dramatic increases in phiecl ranging from 6- to 270-fold were seen in mixed alcohol/water solutions.     

Spectroelectrochemical sensing based on multimode selectivity simultaneously achievable in a single device. 9. Incorporation of planar waveguide technology

Incorporation of planar waveguide technology into a spectroelectrochemical sensor is described. In this sensor design, a potassium ion-exchanged BK7 glass waveguide was over-coated with a thin film of indium tin oxide (ITO) that served as an optically transparent electrode. A chemically selective film was spin-coated on top of the ITO film. The sensor supported five optical modes at 442 nm and three at 633 nm. Investigations on the impact of the ITO film on the optical properties of the waveguide and on the spectroelectrochemical performance of the sensor are reported. Sensing was based on the change in attenuation of light propagated through the waveguide resulting from an optically absorbing analyte. By applying either a triangular or square wave excitation potential waveform, electromodulation of the optical signal has been demonstrated with Fe(CN)6(3-/4-) as a model electroactive couple that partitions into a PDMDAAC-SiO2 film [where PDMDAAC = poly(dimethyldiallylammonium chloride)] and absorbs at 442 nm.     

Electrogenerated chemiluminescence from R(bpy)3(2+) ion-exchanged in carbon nanotube/perfluorosulfonated ionomer composite films

The electrochemistry and electrogenerated chemiluminescence (ECL) of ruthenium(II) tris(bipyridine) (Ru(bpy)(3)(2+)) ion-exchanged in carbon nanotube (CNT)/Nafion composite films were investigated with tripropylamine (TPA) as a coreactant at a glassy carbon (GC) electrode. The major goal of this work was to investigate and develop new materials and immobilization approaches for the fabrication of ECL-based sensors with improved sensitivity, reactivity, and long-term stability. Ru(bpy)(3)(2+) could be strongly incorporated into Nafion film, but the rate of charge transfer was relative slow and its stability was also problematic. The interfusion of CNT in Nafion resulted in a high peak current of Ru(bpy)(3)(2+) and high ECL intensity. The results indicated that the composite film had more open structures and a larger surface area allowing faster diffusion of Ru(bpy)(3)(2+) and that the CNT could adsorb Ru(bpy)(3)(2+) and also acted as conducting pathways to connect Ru(bpy)(3)(2+) sites to the electrode. In the present work, the sensitivity of the ECL system at the CNT/Nafion film-modified electrodes was more than 2 orders of magnitude higher than that observed at a silica/Nafion composite film-modified electrode and 3 orders of magnitude higher than that at pure Nafion films. The CNT/Nafion composite film-modified GC electrodes also exhibited long-term stability.     

Electrochemiluminescence of Tris(2,2'-bipyridine)ruthenium in Water at Carbon Microelectrodes

Electrochemiluminescence (ECL) of Ru(bpy)(3)(2+) in water only, without any added electrolyte or reducing agents, has been obtained at carbon interdigitated microelectrode arrays (C-IDAs) of 2 μm width and spacing. In a generation/collection biasing mode, ECL can be clearly seen with the naked eye in normal room lighting at concentrations greater than 1 mM. Using a conventional photomultiplier tube (PMT), a detection limit of 10(-)(7) M Ru(bpy)(3)(2+) has been achieved for an electrode area of 0.25 mm(2). In comparison, the ECL intensity produced at Pt-IDA of the same geometry, under identical experimental conditions, was more than 300 times less. The ECL obtained at C-IDAs is attributed to the annihilation reaction of the reduced and oxidized forms of the Ru(bpy)(3)(2+) made possible due to the small electrode spacing.     

4-(Dimethylamino)butyric acid labeling for electrochemiluminescence detection of biological substances by increasing sensitivity with gold nanoparticle amplification

4-(Dimethylamino)butyric acid (DMBA) labeling combined with gold nanoparticle amplification for electrochemiluminescence (ECL) determination of a biological substance (bovine serum albumin (BSA) and immunoglobulin G (IgG) as models) was presented. After DMBA, an analogue of tripropylamine, was tagged on the (anti)analytes, an ECL signal related to the content of the analytes was generated when the analyte tagged with DMBA was in contact with tris(2,2'-bipyridine)ruthenium (Ru(bpy)(3)2+) solution and a potential was applied. To improve the adsorption capacity, a gold nanoparticle layer was first combined into the surface of the 2-mm-diameter gold electrode. For the determination of BSA, avidin was covalently conjugated to a self-assembled monolayer of 3-mercaptopropanoic acid on the gold nanoparticle layer. Biotinylated BSA-DMBA was then immobilized on the gold nanoparticle layer of the gold electrode via the avidin-biotin reaction. IgG was tested via a typical sandwich-type immobilization method. ECL signals were generated from the electrodes immobilized with BSA or IgG by immersing them in a 1 mmol L-1 Ru(bpy)(3)2+ solution and scanning from 0.5 to 1.3 V versus Ag/AgCl. With gold nanoparticle amplification, the ECL peak intensity was proportional to the concentration over the range 1-80 and 5-100 microg/mL for BSA and IgG consuming 50 microL of sample, respectively. A 10- and 6-fold sensitivity enhancement was obtained for BSA and IgG over their direct immobilization on an electrode using DMBA labeling. The relative standard deviations of five replicate determinations of 10 microg/mL BSA and 20 microg/mL IgG were 8.4 and 10.2%, respectively. High biocompatibility and low cost were the main advantages of the present DMBA labeling technique over the traditional Ru(bpy)(3)2+ labeling.     

Multilabeling biomolecules at a single site. 1. Synthesis and characterization of a dendritic label for electrochemiluminescence assays

Ultrasensitive bioanalytical assays are of great value for early detection of human diseases and pathogens. The sensitivities of immunoassays and DNA probing can be enhanced by multilabeling the biorecognition partner used for affinity-based assays. However, the bioreactivity of biomolecules is affected by a high degree of multilabeling at multiple functional sites. It is proposed that dendritic scaffoldings be used to link multiple signal-generating units to a single site with potentially minimum impact on the bioaffinity. A prototype label, a zeroth-generation dendron, bearing three [Ru(bpy)(3)](2+) units for electrochemiluminescence (ECL) assays was synthesized and characterized preliminarily by spectroscopic, electrochemical, and ECL methods. No evidence of interaction between the neighboring [Ru(bpy)(3)](2+) units in the label molecule was found from these characterizations. Both the photoluminescence and ECL of the prototype label have features very similar to those of mononuclear [Ru(bpy)(3)](2+) compounds. Labeling a model protein with a triad of [Ru(bpy)(3)](2+) at one NH(2) position was demonstrated. The results reported here provide support to applying the proposed multilabeling strategy to affinity-based bioanalytical assays.     

Strong interaction between imidazolium-based polycationic polymer and ferricyanide: toward redox potential regulation for selective in vivo electrochemical measurements

This study effectively demonstrates a strategy to enable the ferricyanide-based second-generation biosensors for selective in vivo measurements of neurochemicals, with glucose as an example. The strategy is based on regulation of redox potential of ferricyanide mediator by carefully controlling the different adsorption ability of ferricyanide (Fe(CN)(6)(3-)) and ferrocyanide (Fe(CN)(6)(4-)) onto electrode surface. To realize the negative shift of the redox potential of Fe(CN)(6)(3-/4-), imidazolium-based polymer (Pim) is synthesized and used as a matrix for surface adsorption of Fe(CN)(6)(3-/4-) due to its stronger interaction with Fe(CN)(6)(3-) than with Fe(CN)(6)(4-). The different adsorption ability of Fe(CN)(6)(3-) and Fe(CN)(6)(4-) onto electrodes modified with a composite of Pim and multiwalled carbon nanotubes (MWNTs) eventually enables the stable surface adsorption of both species to generate integrated biosensors and, more importantly, leads to a negative shift of the redox potential of the surface-confined redox mediator. Using glucose oxidase (GOD) as the model biorecognition units, we demonstrate the validity of the ferricyanide-based second-generation biosensors for selective in vivo neurochemical measurements. We find that the biosensors developed with the strategy demonstrated in this study can be used well as the selective detector for continuous online detection of striatum glucose of guinea pigs, by integration with in vivo microdialysis. This study essentially paves a new avenue to developing electrochemical biosensors effectively for in vivo neurochemical measurements, which is envisaged to be of great importance in understanding the molecular basis of physiological and pathological events.     

Synthesis and properties of the diruthenium(II) complexes with diimine-linked polypyridine bridges

The diruthenium complexes, [(bpy)2Ru(II)-(bpy-DPDA)-Ru(II)(bpy)2][PF6]4 3, (bpy: 2,2'-bipyridiyl; bpy-DPDA: Bis(2,2'-dipyridylketenylidene)-N,N-1,4-phenylenediamine}, and [(bpy)2Ru(II)-(Dbpy-DPDA)-Ru(II)(bpy)2][PF6]4 4 {Dbpy-DPDA: Bis(2,2'-dipyridyl ketenylidene)-N,N-1,1'-(4,4'-diphenylene)diamine}, were prepared by the reaction of (bpy)2Ru(II)Cl2 with diimine-linked polypyridine bridges. These complexes were characterized by NMR, IR, UV/VIS, PL and cyclic voltammetry. In the 13C-NMR spectra of 3 and 4, the carbon peaks of the Schiff Bases (>C=N-) were shifted to lower fields, and emissions were observed at 689 and 693 nm with quantum yields of 0.004 and 0.006, respectively. The electrochemistry of complexes 3 and 4 showed four-reversible waves (one oxidation wave and three reduction waves). The electrochemically measured band gaps for complexes 3 and 4 were 2.01 and 2.10 eV, respectively.