PVA静电纺丝工艺优化研究

以聚乙烯醇(PVA)为原料、去离子水为溶剂,通过静电纺丝制备PVA纳米纤维膜,利用正交实验探讨静电纺丝过程中纺丝液PVA浓度、纺丝距离、纺丝电压和注射速度对PVA纳米纤维膜形貌及纤维直径的影响,得出制备纤维膜的较佳工艺条件,并分析了纺丝液PVA浓度对纤维膜的力学性能和亲水性能的影响。结果表明：随着纺丝液PVA浓度的增加,PVA纤维的直径逐步变小,直径分布变窄;当纺丝液PVA质量分数为7%、纺丝电压为14 kV、纺丝距离为14 cm、注射速度为0.5 mL/h时,纤维膜的纤维直径最小,为203 nm;正交实验中PVA浓度、纺丝电压、纺丝距离、注射速度4个因素的极差值分别为87.00,49.67,18.33,11.67;纺丝液PVA质量分数从5%增加到7%,纤维膜的断裂强度从2.21 MPa提高至2.81 MPa,断裂伸长率从31.63%提高至56.39%,水接触角从37.7°提高至48.7°。     

丝素蛋白-聚乙烯醇共混改性电纺膜的制备

采用静电纺丝技术,以特殊设计的金属丝螺旋盘绕滚筒作为接收装置,制备了具有一定取向的丝素蛋白(SF)-聚乙烯醇(PVA)共混纳米纤维材料。利用扫描电子显微镜(SEM)对纤维形貌进行观察,并通过Image-Pro Plus软件对纤维细度进行测试,探讨了SF与PVA的配比以及纺丝电压、接收距离等静电纺丝参数对所得纳米纤维形貌、细度及其分布的影响。结果表明:将质量浓度为25 kg/L的SF与质量分数为8%的PVA以质量比15∶3.2共混,并采用20 kV的纺丝电压和13 cm的接收距离静电纺时,所得纳米纤维的平均直径约为238 nm,且直径分布较为均匀。采用该法制得的纳米纤维材料具有一定的纤维取向,有利于细胞生长,可应用于生物医药领域。     

海藻酸钠/聚乙烯醇/银复合纤维的静电纺丝

采用静电纺丝方法,在不同海藻酸钠/聚乙烯醇质量比、含银量、纺丝电压、纺丝液流速、接收距离条件下,制备了海藻酸钠/聚乙烯醇/银复合纤维,利用扫描电镜分析了纤维直径分布及形态。结果表明:海藻酸钠与聚乙烯醇的质量比和含银量对复合纤维成纤性和纤维形态的影响较为显著。海藻酸钠与聚乙烯醇质量比为2∶8、银占溶质质量分数的0.1%、纺丝电压为20 kV、纺丝液流速为0.1 mL/h、接收距离为8 cm时,纺丝效果最佳,纤维形态最好。     

聚乙烯醇静电纺丝纳米纤维的制备及形貌研究

利用静电纺丝技术制备聚乙烯醇（PVA）纳米纤维材料,通过正交试验调节制备过程中纺丝电压、纺丝距离和纺丝溶液浓度等工艺参数,探究其对PVA纳米纤维直径大小、直径分布以及纤维形貌的影响。结果表明,影响纳米纤维形貌的主要因素排序是纺丝溶液浓度＞纺丝距离＞纺丝电压,并确定最优水平组合为纺丝电压为20 kV,PVA纺丝溶液浓度为6 %(质量分数,下同),纺丝距离为12 cm。     

静电纺抗紫外PVA/芦丁纳米纤维膜的制备及其性能研究

以聚乙烯醇(PVA)为原料,以芦丁为改性剂,将PVA与芦丁共混于去离子水中,通过静电纺丝制备抗紫外PVA/芦丁纳米纤维膜,并对其性能进行表征。结果表明:静电纺丝工艺条件为电压20 k V,纺丝速度0.5 m L/h,接收距离10 cm,温度30℃;加入少量芦丁,对PVA静电纺丝成纤性无影响,但纤维直径增大,直径均匀性变差;纤维中PVA与芦丁之间存在氢键;相对PVA,芦丁质量分数为4.76%时,PVA/芦丁纳米纤维膜的纤维平均直径为302 nm,抗紫外系数大于40,具有良好的抗紫外性能。     

聚乙烯醇纳米纤维膜的制备

采用静电纺丝方法制备了聚乙烯醇(PVA)纳米纤维,探讨了工艺参数对纳米纤维形貌的影响,并对PVA纳米纤维膜进行热处理,研究了热处理时间与温度对纳米纤维膜力学性能的影响。研究表明:PVA质量分数在6%~10%区间内变化时,可得到直径分布较为均匀的纳米纤维;在其它条件相同时,随纺丝电压的升高,PVA纳米纤维的不匀增大;接收距离的改变对PVA纳米纤维的直径变化影响不大;随PVA质量分数的增加,纳米纤维膜的断裂强度和断裂伸长率逐渐增大;在热处理时间相同时,PVA纳米纤维膜的断裂强度随温度的升高而增大;处理温度相同时,随处理时间的延长,PVA纳米纤维膜的断裂强度变化不大。     

静电纺丝法纺制聚乳酸纳米纤维无纺毡

采用静电纺丝法制备了生物降解聚乳酸(PLLA)纳米纤维无纺毡。分析了纺丝液浓度、电压、接收距离、挤出速度等因素对纤维形态的影响。结果表明:纺丝液的浓度和挤出速度对纤维直径的影响较为明显,溶液挤出速度增大,所得纤维微孔含量及尺寸也增大;适当的电压和接收距离有利于收集无液滴纤维;随着纤维直径的减小,无纺毡的孔径呈减小趋势。在PLLA质量分数为5．7％、挤出速度0．8 mL／h、接受距离 15．5 cm、电压8 kV的静电纺丝条件下,可制备纤维直径为200-400 nm的PLLA纳米纤维无纺毡。     

静电纺PCL纤维形态与热性能的研究

利用静电纺丝法制备了超细聚ε-己内酯(PCL)纤维;借助扫描电镜仪和差示扫描量热仪表征了PCL纤维的形态与热性能;研究了电纺过程中溶液浓度、电压、接收距离和纺丝速度对纤维形态的影响。结果表明:当纺丝电压为10 kV,接收距离为15 cm,纺丝速度为2 mL/min时,纺丝液中PCL质量分数为6%~12%能获得连续无串珠的纤维;纺丝电压为8~12 kV,电纺过程稳定;接收距离对纤维的直径和形貌无明显影响;与流延成型的PCL膜相比,电纺PCL纤维具有较低的结晶度。     

静电纺工艺参数对SEBS纤维形貌和直径的影响

通过静电纺丝,将苯乙烯-乙烯-丁烯-苯乙烯嵌段共聚物(SEBS)溶解于四氢呋喃(THF)中的纺丝液制备成SEBS纤维,探索了纺丝液质量分数、纺丝电压和接收距离对纤维形貌及直径的影响.通过扫描电镜观察SEBS纤维的形貌以及Photoshop软件测量了SEBS纤维的直径.结果表明,纺丝液质量分数为25％、纺丝电压为10 k...     

钢丝毛刷辊式静电纺PVA纳米纤维

设计了一种批量制备连续纤维的钢丝毛刷辊静电纺丝装置,研究了固定距离时溶液浓度及电压对毛刷PVA溶液静电纺丝产量的影响。考察了不同浓度PVA在不同纺丝距离、纺丝电压、毛刷转速下的纤维直径分布与纤维形貌。借助扫描电镜对制得的纳米纤维形貌进行观察,并应用Nano Measurer软件对纤维的直径及其分布进行了测量统计。综合考察结果,得出最佳的纺丝溶液浓度为12%,接收板距离为10 cm,电压为40 k V。     

Preparation of atactic poly(vinyl alcohol)/silver composite nanofibers by electrospinning and their characterization

Poly(vinyl alcohol) (PVA)/silver composite nanofibers were successfully prepared by the electrospinning method. Water‐based colloidal silver in a PVA solution was directly mixed without any chemical or structural modifications into PVA polymer fibers to form organic–inorganic composite nanofibers. The ratio of silver colloidal solution to PVA played an important role in the formation of the PVA/silver composite nanofibers. We prepared two different atactic PVA/silver nanocomposites with number‐average degrees of polymerization of 1700 and 4000 through electrospinning with various processing parameters, such as initial polymer concentration, amount of silver colloidal solution, applied voltage, and tip‐to‐collector distance. The PVA/silver composite nanofibers were characterized by field emission scanning electron microscopy and transmission electron microscopy (TEM). TEM images showed that silver nanoparticles with an average diameter of 30–50 nm were obtained and were well distributed in the PVA nanofibers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The optical properties of PVA/TiO2 composite nanofibers

The electrospun nanofibers emerge several advantages because of extremely high specific surface area and small pore size. This work studies the effect of PVA nanofibers diameter and nano‐sized TiO₂ on optical properties as reflectivity of light and color of a nanostructure assembly consisting polyvinyl alcohol and titanium dioxide (PVA/TiO₂) composite nanofibers prepared by electrospinning technique. The PVA/TiO₂ composite spinning solution was prepared through incorporation of TiO₂ nanoparticles as inorganic optical filler in polyvinyl alcohol (PVA) solution as an organic substrate using the ultrasonication method. The morphological and optical properties of collected composites nanofibers were highlighted using scanning electron microscopy (SEM) and reflective spectrophotometer (RS). The reflectance spectra indicated the less reflectance and lightness of composite with higher nanofiber diameter. Also, the reflectance and lightness of nanofibers decreased with increasing nano‐TiO₂ concentration. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

A comprehensive study on Plantago ovata/PVA biocompatible nanofibers: Fabrication,characterization, and biological assessment

In this study, a biocompatible nanofiber is fabricated using Plantago ovata mucilage (POM) combined with polyvinyl alcohol (PVA), which is considered as a non-toxic polymer. High quality nanofibers were produced by controlling the electrospinning parameters after selecting an appropriate solvent for the POM/PVA combination (12% PVA and 3% POM). Electrospinning parameters, including high voltage, distance from collector to tip, feed rate and POM to PVA proportion were optimized following preparation of an aqueous POM/PVA solution. Using the results of scanning electron microscopy, the optimized electrospinning conditions for producing POM/PVA nanofibers were determined (high voltage = 18 kV, distance = 15 cm, feed rate = 0.125 ml/hr, PMM/PVA = 50/50) and uniform nanofibers with an average diameter of 250 nm were produced. The POM/PVA nanofiber sample was evaluated by determining the mechanical strength, characterization of produced nanofiber morphology, and investigating the cell viability by applying MTT assay. The bands for both POM and PVA from FTIR results showed that the samples remained stable. The tensile strength results showed that blending POM with PVA solution enhanced the Young's modulus by factor of 3.2 (0.2 MPa to 0.64 MPa). The MTT analysis on POM/PVA cell lines proved that the produced nanofiber considerably enabled the cellular proliferation. Enhancement in these analysis indicated how POM-based nanofibers is a promising scaffold for cell culture, drug delivery systems and food additives.     

Preparation and characterization of graphene oxide/poly(vinyl alcohol) composite nanofibers via electrospinning

Graphene oxide (GO) was well dispersed in poly(vinyl alcohol) (PVA) diluted aqueous solution, and then the mixture was electrospun into GO/PVA composite nanofibers. Electron microscopy and Raman spectroscopy on the as‐prepared and calcined samples confirm the uniform distribution of GO sheets in the nanofibers. The thermal and mechanical properties of the nanofibers vary considerably with different GO filler contents. The decomposition temperatures of the GO/PVA composite nanofiber dropped by 38–50°C compared with pure PVA. A very small loading of 0.02 wt % GO increases the tensile strength of the nanofibers by 42 times. A porous 3D structure was realized by postcalcining nanofibers in H₂. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

静电纺丝法制备PVA/Fe_3O_4磁性纳米纤维

将纳米Fe3O4磁性颗粒加入含分散剂的聚乙烯醇水溶液中,选取卵蛋白粉为分散剂,利用静电纺丝制备磁性纳米纤维。通过扫描电镜(SEM)和透射电镜(TEM)表征纤维形貌和分析溶液中粒子分散情况,选用古埃磁天平对纳米纤维毡进行磁性测试。实验结果表明,所制得的复合纳米纤维成纤性良好,粒子分散均匀,且具有一定的磁性。     

聚L-乳酸/菜籽蛋白共混纳米纤维毡的制备与表征

以聚L-乳酸、菜籽蛋白为原料,高压静电纺丝制备聚L-乳酸(PLLA)/菜籽蛋白共混复合纳米纤维毡,考察了不同电压、极距和三氟乙酸添加量对纳米纤维形态及直径的影响,采用傅里叶变换红外光谱(FT-IR)、扫描电镜(SEM)和X-射线衍射(XRD)对相关产物进行结构表征。结果表明:复合纤维中PLLA与菜籽蛋白之间以氢键结合,PLLA的结晶性能降低;PLLA纺丝溶液中,菜籽蛋白的三氟乙酸溶液的适量引入可显著提高纺丝速率。在PLLA质量浓度为24%的氯仿溶液中,6.5%菜籽蛋白的三氟乙酸溶液加入量为0.25 mL,电压16 kV,极距10 cm的条件下,可快速制备平均直径622 nm的PLLA/菜籽蛋白复合纳米纤维毡,纺丝速率达到5.2 mg/min。     

Effects of poly (vinyl alcohol) (PVA) content on preparation of novel thiol-functionalized mesoporous PVA/SiO2 composite nanofiber membranes and their application for adsorption of heavy metal ions from aqueous solution

Thiol-functionalized mesoporous poly (vinyl alcohol)/SiO₂ composite nanofiber membranes and pure PVA nanofiber membranes were synthesized by electrospinning. The results of Fourier transform infrared (FTIR) indicated that the PVA/SiO₂ composite nanofibers were functionalized by mercapto groups via the hydrolysis polycondensation. The surface areas of the PVA/SiO₂ composite nanofiber membranes were >290 m²/g. The surface areas, pore diameters and pore volumes of PVA/SiO₂ composite nanofibers decreased as the PVA content increased. The adsorption capacities of the thiol-functionalized mesoporous PVA/SiO₂ composite nanofiber membranes were greater than the pure PVA nanofiber membranes. The largest adsorption capacity was 489.12 mg/g at 303 K. The mesoporous PVA/SiO₂ composite nanofiber membranes exhibited higher Cu²⁺ ion adsorption capacity than other reported nanofiber membranes. Furthermore, the adsorption capacity of the PVA/SiO₂ composite nanofiber membranes was maintained through six recycling processes. Consequently, these membranes can be promising materials for removing, and recovering, heavy metal ions in water.     

Fabrication and characterization of electrospun psyllium husk-based nanofibers for tissue regeneration

The present study reports for first time the blending of psyllium husk (PH) powder/gelatin (G) in the polymer-rich composition of polyvinyl alcohol (PVA) to make an electrospinnable solution. The composite was prepared in 3 different ratios viz., 100% (wt/wt) (PVA + PH), 75% + 25% (PVA + 75PH + 25G) (wt/wt) and 50% + 50% (PVA + 50PH + 50G) (wt/wt) in 6% PVA solution. Optimum electrospinning parameters were evaluated for all the prepared blends. The fabricated nanofibers were characterized by scanning electron microscopy (SEM), attenuated total reflectance-Fourier transform infrared, differential scanning calorimetry, porosity percentage, and fiber orientation using ImageJ software. A qualitative in vitro degradation study at room temperature is supported by SEM images. The cellular interactions were characterized by MTT assay of NIH-3T3 fibroblast cells for 2 and 4 days with an optimum cell growth of >50% by fourth day of culture and long-term cultivation of L929-RFP cells was observed for 10 days. The nanofibers were formed in the range of 49–600 nm. PVA + 75PH + 25G when cultured with L929-RFP cells exhibited highest fluorescence intensity and thus supported cellular proliferation significantly. Based on the results obtained from various analyses, we anticipate that fabricated psyllium-based nanofiber can be used as a promising candidate for wound healing and other biomedical applications.     

Microstructure and characterization of electrospun poly(vinyl alcohol) nanofiber scaffolds filled with graphene nanosheets

Graphene nanosheets (GNSs) have attracted significant scientific attention because of their remarkable features, including exceptional electron transport, excellent mechanical properties, high surface area, and antibacterial functions. Poly(vinyl alcohol) (PVA) solutions filled with GNSs were prepared for electrospinning, and their spinnability was correlated with their solution properties. The effects of GNS addition on solution rheology and conductivity were investigated. The as‐spun fibers were characterized via scanning electron microscopy (SEM), transmission electron microscopy (TEM), wide‐angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC). The results revealed the effects of GNS on the microstructure, morphology, and crystallization properties of PVA/GNS composite nanofibers. The addition of GNSs in PVA solution increased the viscosity and conductivity of the solution. The electrospun fiber diameter of the PVA/GNS composite nanofiber was smaller than that of neat PVA nanofiber. GNSs were not only embedded at the fibers but also formed protrusions on the fibers. In addition, the crystallinity of PVA/GNS fiber decreased with higher GNS content. The possible application of PVA/GNS fibers in tissue engineering was also evaluated. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41891.