On the performance of dynamically loaded journal bearings lubricated with couple stress fluids

A numerical study of the performance for a dynamically loaded journal bearing lubricated with couple stress fluids is undertaken. First of all, on the basis of micro-continuum theory, the generalized Reynolds equation for dynamic loads is derived. Then it is simultaneously solved with the force balance equation of the journal, thus obtaining the transient oil film pressure, the transient position and velocity of the journal center. Results from this analysis are presented for a typical engine crankshaft bearing. It is shown, compared with Newtonian lubricants, that under a dynamic loading lubricants with couple stress yield an obvious increase in oil film pressure and oil film thickness, but a decrease in the side leakage flow. Moreover, the effects of couple stress on friction force and friction coefficient vary considerably with time.     

Wall slip and hydrodynamics of two-dimensional journal bearing

In the present paper, based on the limiting shear stress model, a multi-linearity finite element algorithm and quadratic programming technique are used to study the influence of wall slip on the hydrodynamic lubrication performance of a two-dimensional journal bearing (finite length journal bearing). It is found that if the lubricated surfaces are designed as homogeneous slip surfaces, the hydrodynamic force will be decreased. If the shaft surface (rotation) is a slippery surface with very low limiting shear stress, almost no fluid load support can be generated. If the sleeve surface is designed as the homogeneous slip surface, a low fluid load support together with a small friction drag can be obtained. However, if the sleeve surface is designed as an optimized slip surface with a slip zone in the inlet region, a high load support and low friction coefficient can be obtained. Optimization of the shape and the size of the slip zone can give the journal bearing many advanced properties.     

磁流体润滑滑动轴承的研制和性能研究

研制了磁流体润滑滑动轴承 ,建立了磁流体滑动轴承试验装置。对磁流体滑动轴承和传统滑动轴承进行了对比试验研究。通过大量试验的测试结果分析比较 ,发现磁流体滑动轴承能形成良好的全油膜润滑 ,产生的摩擦力比传统滑动轴承要小得多 ,因此推断出磁流体滑动轴承的承载能力和抗磨损能力大于同等条件下的传统滑动轴承。     

超临界二氧化碳动静压径向可倾瓦轴承实验台设计与实验研究

针对超临界二氧化碳(S-CO₂)动力机组在启动和停止阶段气体轴承产生非常大的摩擦磨损,以及气体轴承承载力低、刚度低、阻尼小、稳定性较差等问题,设计并改进一种新型动静压S-CO₂润滑径向可倾瓦轴承结构。设计并搭建S-CO₂润滑轴承实验台,针对于实验台转子刚启动和极低转速工况,对新型S-CO₂润滑动静压径向轴承在静压状态下的动态特性进行实验研究,得到轴承的动态刚度和动态阻尼,并分析静压对轴承动态性能的影响。实验结果表明,设计的S-CO₂动静压径向可倾瓦轴承在启停阶段,在轴瓦与轴颈之间产生了足够的静压压力,可将二者完全分隔开,从而能减少启停阶段的摩擦磨损;随着静压压力的增大,轴承X、Y方向上的整体刚度、主阻尼都增大,且2个方向的主刚度系数差别不大,而交叉刚度和交叉阻尼都接近于0。研究结果为进一步揭示S-CO₂润滑径向轴承动压状态特性提供参考。     

Suggestion of MSTV (Modified-Stick-Transition-Velocity) model for hysteretic damping mechanism

To decrease vibration and noise in washing machines, lubricated friction dampers were installed. Although the structure of the friction damper is simple, it was not easy to develop a mathematical model for the dynamic behavior of the lubrication damper. To see the dynamic behavior of a friction damper, physical tests were carried out via a material testing machine by changing exciting amplitudes and frequencies. Complicated curves of spring characteristics and damping showed a hysteretic behavior. In this paper, a reasonable model for a friction damper is suggested. To model the hysteretic behavior of a friction damper, a Coulomb friction model was first applied. To get a refined model for stick and transition, an STV (stick transition velocity) model was analyzed. To develop a more accurate mathematical model, an MSTV (modified stick transition velocity) model was proposed. In the MSTV model, the friction force could be changed due to the velocity of the damper, and the damping force was calculated according to the relative velocity between the external displacement and the deformation of the sponge in the friction damper. The MSTV model was in a good agreement with the experimental results.     

界面滑移对圆柱形凹坑织构滑动轴承摩擦力的影响

为研究不同的滑移情况对圆柱形凹坑织构滑动轴承摩擦力的影响,建立含有圆柱形凹坑织构的滑动轴承在不同界面滑移状态下的摩擦力计算模型,探究影响织构化滑动轴承摩擦力的参数,并借助ANSYS分析不同滑移情况下界面滑移对圆柱形凹坑织构滑动轴承摩擦力的影响规律。结果表明:织构化滑动轴承的摩擦力主要是由轴颈线速度、油膜滑移比、轴承的进出油口压力、织构处油膜压力、织构深度、油膜厚度和承载力决定;不同滑移情况下织构模型的摩擦力均小于无织构模型;且在上下表面均滑移时,圆柱形凹坑织构在出口位置时表现出最优的承载和减摩效果;适当地增加圆柱形凹坑织构的深度可以改善模型的摩擦性能,但是过深的凹坑织构并不能发挥出其性能。     

Boundary slip surface design for high speed water lubricated journal bearings

This paper presents the development of a numerical model for high speed and water lubricated journal bearings with different boundary slip arrangements. The effect of boundary slip and its possible mechanism are analyzed and discussed. The results suggest that a suitable combination of slip/no-slip surfaces on the sleeve of a journal bearing enables improvement of the tribological performance through (i) suppressing the occurrence of cavitation, (ii) enhancing the load bearing capacity, and (iii) reducing the interfacial friction between bearing sleeve and shaft. Such improvement becomes more significant for the bearings with smaller eccentricity ratio, smaller width and larger diameter.     

Investigation of Oil Additives for Boundary Lubrication of Railroad Journal Bearings

The boundary friction properties of the lubricated system of steel sliding on lead-base babbitt were investigated as a phase of the Association of American Railroads' sponsored project on freight car hot boxes. A friction pendulum was developed for determining the coefficients of boundary friction as a function of temperature with the specified metals lubricated with various lube oil additive blends.

A group of general relationships dealing with additives for the steel-babbitt system was developed. It is concluded that the extreme pressure agents containing sulfur or chlorine are generally unsuited for railroad journal bearing use. Lubricity additives which function by simple physical adsorption were found to be ineffective at moderate or high temperatures existing in railroad operations. Those lubricity additives which chemisorb to metal surfaces and form a close-packed layer were found to be effective antifriction agents.     

A numerical method for the calculation of lubricant pressures in bearings with mixed lubrication

A model for mixed lubrication, assuming that the total normal load applied to the plane of the lubricated surfaces is carried partly by the hydrodynamic action of the lubrication film and partly by asperity contacts and that the total friction force between the lubricated surfaces is partly due to viscous friction and partly to asperity contacts, was used to develop a numerical solution for pressure distribution in a bearing experiencing mixed lubrication. The geometry treated and the pressure distribution obtained were for a simple slider bearing, but the method could easily be extended to other shapes. The model is based on measured roughness of a real surface. Real load carrying capacity and drag can therefore be determined since they are related directly to bearing pressure distribution     

Modelling lubricated friction for dynamic contact systems

Multi-valued friction is often observed in lubricated contact systems operating under unsteady sliding conditions. In the past, this behaviour has been modelled using a measured time delay between changes in sliding velocity and resulting changes in friction. More recent work has revealed that fluctuations in normal separation are the principal cause of this deviation from steady friction behaviour. This paper demonstrates that tangential contact dynamics can result in apparent deviations from steady friction that can resemble true deviations found from fluctuations in normal separation. Two different dynamic models are considered. One model accommodates the tangential rider dynamics of a friction test apparatus. The other model considers the possibility of tangential dynamics associated with asperity contacts.     

Wear and friction of synthetic esters in a boundary lubricated journal bearing

This study concerns the case of a slow intermittent motion, conformal contact, high load bronze journal bearing against a hardened steel shaft lubricated in an oil bath at a temperature about of 13 °C. Three synthetic esters were used: one pure and two formulated ones. Worn surfaces were examined using SEM-EDS to determine the wear mechanism. The tested lubricants were examined using ICP-AES to identify the elements present.The results show the wear rate, friction and temperature in the subsurface of the journal bearing material. An initial bronze–steel contact develops into a copper–copper contact along the sliding distance. Wear element concentration in the oil and friction surfaces departs from the elementary concentration in the journal bearing bronze base material. The copper layer thickness depended on additives in the synthetic esters, load and wear rate.     

Tribological properties of metal-plastic multilayer composites under oil lubricated conditions

Three kinds of metal-plastic multilayer composites, which were composed of a steel backing, a middle layer of sintered porous bronze and a surface layer of polytetrafluoroethylene (PTFE) filled by Pb or Cu₂O powders, were prepared. The friction and wear properties as well as the limiting pressure times velocity (PV) values of these metal-plastic multilayer composites sliding against 45 carbon steel under both dry and oil lubricated conditions were evaluated on a MPV-1500 friction tester with a steel axis rotating on a journal bearing. The worn surfaces of these metal-plastic multilayer composites and the transfer films formed on the surface of steel axis were examined by electron probe microscopy analysis (EPMA). Experimental results show that filling of Pb to PTFE reduces the friction coefficient and wear of the composite, while filling of Cu₂O to PTFE increases the friction coefficient but decreases the wear of the composite. The friction and wear properties as well as the limiting PV values of these metal-plastic multilayer composites can be greatly improved with the oil lubrication. EPMA investigations show that Pb and Cu₂O fillers preferentially transfer onto the surfaces of steel axis, which may enhance or deteriorate the adhesion between transfer films and steel surfaces. Meanwhile the transfer of these metal-plastic multilayer composites onto the steel surface can be greatly reduced with oil lubrication, which results in the remarkable decrease of the wear of these metal-plastic multilayer composites.     

The Use of D-optimal Design for Modeling and Analyzing the Tribological Characteristics of Journal Bearing Materials Lubricated by Nano-Based Biolubricants

Response surface methodology (RSM) based on a D-optimal design was employed to investigate the tribological characteristics of journal bearing materials such as brass, bronze, and copper lubricated by a biolubricant, chemically modified rapeseed oil (CMRO). The wear and friction performance were observed for the bearing materials tested with TiO₂, WS₂, and CuO nanoadditives dispersed in the CMRO. The tests were performed by selecting sliding speed and load as numerical factors and nano-based biolubricant/bearing materials as the categorical factor to evaluate the tribological characteristics such as the coefficient of friction (COF) and specific wear rate. The results showed that RSM based on a D-optimal design was instrumental in the selection of suitable journal bearing materials for a typical system, especially one lubricated by nano-based biolubricant. At a sliding speed of 2.0 m/s and load of 100 N, the bronze bearing material with CMRO containing CuO nanoparticles had the lowest COF and wear rate. In addition, scanning electron microscopy (SEM) examination of the worn bearing surfaces showed that the bronze bearing material lubricated with CMRO containing CuO nanoadditive is smoother than copper/brass bearing material.     

Approximate closed‐form solution for the dynamical analysis of short bearings with couple stress fluid

The film forces in journal bearings may cause self‐exciting oscillations under particular operating conditions; if the amplitude of these oil‐whirl oscillations becomes too large, it may involve unsafe machinery dynamics. Thus, there is a need to understand the dynamic characteristics of the journal bearings evaluating the performances of the couple stress lubricants used to minimise the friction losses in steady operating conditions. The purpose of this paper was to illustrate a method to formulate with closed‐form solutions the non‐steady fluid film forces, and the stiffness and damping coefficients for ‘short’ liquid‐lubricated couple stress journal bearings, assuming the micro‐continuum Stokes' model. It is shown that the model allows the advantage of minimising the computational time required for the non‐linear dynamic analysis of couple stress journal bearings without any significant loss of accuracy, while the analytical form of the solution involves a better readability of the parameter effects on the system unsteady behaviour. Copyright © 2007 John Wiley & Sons, Ltd.     

Modeling of Dynamic Friction in Lubricated Line Contacts for Precise Motion Control

A simple dynamic friction model for an elastohydrodynamic lubrication sliding and rolling line contact has been developed. This model uses the technique introduced earlier by Harnoy and Friedland (1). The model includes low-velocity regions where friction is a combination of contact and elastohydrodynamic friction. The study shows that the lime-variable friction is not only a function of instantaneous sliding velocity, but is also a memory function of the velocity history. Simulation of the model for an oscillating velocity exhibits similar hysteresis effects in friction-velocity curves as observed earlier in several experimental studies. The model can be useful for friction compensation to enhance the precision of motion in control systems.     

CFD analysis of journal bearing hydrodynamic lubrication by Bingham lubricant

Design of smart journal-bearing systems is an important issue that opens up the possibility for semi-active dynamic control of bearing behavior. Recent studies show that there is an increasing interest in designing hydrodynamically lubricated bearings using electro-rheological fluids (ERFs) or magneto-rheological fluids (MRFs). Both smart fluids behave like Bingham fluids, and thus the Bingham plastic model is used to describe the grease and the electro-rheological (ER) and magneto-rheological (MR) fluids behavior of the non-Newtonian fluid flow. The performance characteristics of a hydrodynamic journal bearing lubricated with a Bingham fluid are derived by means of three-dimensional computational fluid dynamics (3-D CFD) analysis. The FLUENT software package is used to calculate the hydrodynamic balance of the journal using the so-called “dynamic mesh” technique. The results obtained from the developed 3-D CFD model are found to be in very good agreement with experimental and analytical data from previous investigations on Bingham fluids.Journal-bearing performance characteristics, such as relative eccentricity, attitude angle, pressure distribution, friction coefficient, lubricant flow rate, and the angle of maximum pressure, are derived and presented for several length over diameter (L/D) bearing ratios and dimensionless shear numbers T₀ of the Bingham fluid. The above diagrams are presented in the form of Raimondi and Boyd charts, and can easily be used in the design and analysis of journal bearings lubricated with Bingham fluids. The core profile formed in the bearing is also calculated and presented for various bearing eccentricities, L/D ratios, and shear numbers T₀, and found to be in very good agreement with previous experimental and theoretical investigations. The analysis presented here leads to charts that could be used by the designer engineer to design smart journal bearings.     

A study on the effect of surface topography on rough friction in roller contact

The friction behaviour of gear teeth in the context of tribology can have a strong effect on housing vibration, noise and efficiency. One of the parameters that greatly influences the friction under certain running conditions is surface roughness. In this work, rough friction was studied in lubricated sliding of roller surfaces, which were manufactured to simulate the real gear surfaces. By examining 3D surface topography of two mating bodies, both surface roughness and its effect on friction behaviour can be studied. In a previous study, a rough-friction test rig has been designed, constructed and initially verified. The types of surfaces involved in this study are ground, shot-peened, phosphated and electrochemically deburred. These rollers were subjected to the same friction testing procedures. Roller surfaces were then examined, and correlation between the topography and the frictional behaviour was analysed. Friction behaviour was interpreted in terms of Stribeck curves (friction coefficient as the function of Hersey parameter (ην/p)). The results showed that electrochemically deburred and certain phosphated surfaces provide lower friction coefficient values which are competitive to fine-ground surfaces in lubricated rolling/sliding contact.     

Influence of the Wetting Properties of Liquids on the Tribological Behavior of Selected Sliding Materials in Mechanical Seals

Theoretical investigations are carried out for a plain journal bearing considering the influence of thermal effects on non-Newtonian lubrication. With reasonable assumptions, the steady state and dynamic characteristics are presented using a thermohydrodynamic analysis of a bearing lubricated by a nonlinear, i.e., cubic, fluid model.

Experiments are conducted on a rig to study the steady state and dynamic performance of a full journal bearing with different types of non-Newtonian lubricants. Experiments include the measurements of eccentricity ratio, critical speed, and stability limit.

The theoretical investigation reveals that the interaction of the non-Newtonian effect and the thermohydrodynamic effect is strong for friction, and the interaction effect is negligible in the case of eccentricity ratio, attitude angle, and lubricant flow rate. Further, for relatively high values of non-Newtonian parameter, α_n , the effect due to the non-Newtonian parameter is not negligible.     

Controllable high speed journal bearings, lubricated with electro-rheological fluids. An analytical and experimental approach

The problem of journal bearings control is of great importance in mechanical engineering. A very recent method for doing this is the creation of ‘smart' journal bearings using electro-rheological (ER) fluids. If such a fluid is used to lubricate a journal bearing system, it is expected that the imposition of an electric field between the rotor and the stator will cause an alteration in the dynamic properties of the journal bearing. In this paper an experiment in a high speed journal bearing (16 000 to 35 000 s⁻¹), with small radial clearance is presented. The alternation of the attitude locus (eccentricity and attitude angle) and the stiffness coefficients in a loaded journal bearing lubricated with ER fluid is investigated and presented. The Reynolds equation is solved using the finite element method in order to get the dynamic characteristics of the ER bearings vs the electric field and to simulate its dynamic behavior. The Bingham plastic model of non-Newtonian fluid flow behavior is used to described the ER lubricant. The accuracy of the algorithm is obtained by comparing the results published by previous investigators and the experimental data described in this paper. It is concluded that ER fluids can be used to create ‘smart' journal bearings. and vibration controllers can be constructed to control the dynamics and stability of the ER fluid lubricated bearings.