Ag surfactant effects of TiO2 films prepared by sputter deposition

The surfactant effect of Ag on the thin film structure of TiO₂ by radio frequency magnetron sputtering has been investigated. Comparisons between the atomic force microscopy images revealed that the surface roughness of TiO₂ film mediated by Ag was smaller than that of the TiO₂ film without Ag. The surface segregation effect of Ag was confirmed using X-ray photoelectron spectroscopy. The results of X-ray diffraction revealed that the initial deposition of a 0.4 nm thick Ag surfactant layer onto a Fe buffer layer prior to the deposition of the TiO₂ film reduced the rutile (110) growth and enhanced the anatase (100) growth. It was concluded that Ag was an effective surfactant for changing the thin film structure of TiO₂ on the Fe buffer layer. The photocatalytic effect of the fabricated TiO₂ film was also investigated using the remote oxidation process. TiO₂ films with the Ag surfactant exhibited higher photocatalytic activity than conventionally deposited TiO₂ films.     

Growth and characterization of nitrogen-doped TiO2 thin films prepared by reactive pulsed laser deposition

Nitrogen-doped titanium dioxide (TiO₂) thin films were grown on (001) SiO₂ substrates by reactive pulsed laser deposition. A KrF* excimer laser source (λ = 248 nm, τ_FWHM ≅ 10 ns, ν = 10 Hz) was used for the irradiations of pressed powder targets composed by both anatase and rutile phase TiO₂. The experiments were performed in a controlled reactive atmosphere consisting of oxygen or mixtures of oxygen and nitrogen gases. The obtained thin film crystal structure was investigated by X-ray diffraction, while their chemical composition as well as chemical bonding states between the elements were studied by X-ray photoelectron spectroscopy. An interrelation was found between nitrogen concentration, crystalline structure, bonding states between the elements, and the formation of titanium oxinitride compounds. Moreover, as a result of the nitrogen incorporation in the films a continuous red-shift of the optical absorption edge accompanied by absorption in the visible spectral range between 400 and 500 nm wavelength was observed.     

Photoreduction of CO2 by TiO2 nanocomposites synthesized through reactive direct current magnetron sputter deposition

The photoreduction of CO₂ into methane provides a carbon-neutral energy alternative to fossil fuels, but its feasibility requires improvements in the photo-efficiency of materials tailored to this reaction. We hypothesize that mixed phase TiO₂ nano-materials with high interfacial densities are extremely active photocatalysts well suited to solar fuel production by reducing CO₂ to methane and shifting to visible light response. Mixed phase TiO₂ films were synthesized by direct current (DC) magnetron sputtering and characterized by X-ray diffraction (XRD), atomic force microscope (AFM), scanning electron microscope (SEM) and transmission electron microscope (TEM). Bundles of anatase-rutile nano-columns having high densities of two kinds of interfaces (those among the bundles and those between the columns) are fabricated. Films sputtered at a low deposition angle showed the highest methane yield, compared to TiO₂ fabricated under other sputtering conditions and commercial standard Degussa P25 under UV irradiation. The yield of methane could be significantly increased (~ 12% CO₂ conversion) by increasing the CO₂ to water ratio and temperature (< 100 °C) as a combined effect. These films also displayed a light response strongly shifted into the visible range. This is explained by the creation of non-stoichiometric titania films having unique features that we can potentially tailor to the solar energy applications.     

Microanalysis of Pd and V-doped TiO2 thin films prepared by sputtering

Thin films of TiO₂ doped with vanadium and palladium, prepared by the magnetron sputtering method, were studied by means of X-ray diffraction (XRD), Scanning Electron Microscopy with Energy Disperse Spectrometer (SEM-EDS) and Atomic Force Microscopy (AFM). Investigations have brought important information about microstructure due to dopant incorporation in the TiO₂ host lattice. Directly after deposition thin films were XRD-amorphous and SEM investigations did not reveal details on the microstructure. Analysis of the topography of prepared thin films required application of Atomic Force Microscope. The AFM images show that as-deposited sample was dense with grain sizes varied in the range of 5.5 nm-10 nm, that indicated high quality nanocrystalline behavior. Additional annealing results in the formation of three phases in the thin film, e.g. (Ti,V)O₂ — solid solution, PdO and metallic inclusions of Pd. SEM-EDS system allowed analysis of the elemental composition, especially the V one, which lines have not been evidenced in the XRD diffraction pattern. EDS maps show homogenous distribution of elements Ti, O, V, Pd in prepared thin films.     

Photocatalytic activities of TiO2 thin films prepared on Galvanized Iron substrate by plasma-enhanced atomic layer deposition

Titanium dioxide (TiO₂) thin films were prepared on Galvanized Iron (GI) substrate by plasma-enhanced atomic layer deposition (PE-ALD) using tetrakis-dimethylamido titanium and O₂ plasma to investigate the photocatalytic activities. The PE-ALD TiO₂ thin films exhibited relatively high growth rate and the crystal structures of TiO₂ thin films depended on the growth temperatures. TiO₂ thin films deposited at 200 °C have amorphous phase, whereas those with anatase phase and bandgap energy about 3.2 eV were deposited at growth temperature of 250 °C and 300 °C. From contact angles measurement of water droplet, TiO₂ thin films with anatase phase and Activ™ glass exhibited superhydrophilic surfaces after UV light exposure. And from photo-induced degradation test of organic solution, anatase TiO₂ thin films and Activ™ glass decomposed organic solution under UV illumination. The anatase TiO₂ thin film on GI substrate showed higher photocatalytic efficiency than Activ™ glass after 5 h UV light exposure. Thus, we suggest that the anatase phase in TiO₂ thin film contributes to both superhydrophilicity and photocatalytic decomposition of 4-chlorophenol solution and anatase TiO₂ thin films are suitable for self-cleaning applications.     

Effects of internal stress on photocatalytic properties of TiO2 films

Effects of internal stress on photocatalytic properties have been investigated on titanium dioxide films deposited by reactive magnetron sputtering. Atomic peening effects by bombardments of high-energy particles in sputtering processes should generate not only compressive stress, but also oxygen defects in the films. Therefore, the films with higher compressive stress performed almost no photocatalytic activity. Furthermore, compressive or tensile stress was applied on the films deposited on curved micro sheet glasses by flattening the substrates after the deposition by external force. It was found that the photodecomposition activity of the films applied the slight compressive stress improved clearly, whereas the one of the films applied the tensile stress degraded.     

Optical properties of sputter deposited transparent and conducting TiO2:Nb films

Transparent and conducting thin films of TiO₂:Nb were prepared on glass by reactive dc magnetron sputtering in Ar + O₂. Post-deposition annealing in vacuum at 450 °C led to good electrical conductivity and optical transparency. The optical properties in the sub-bandgap region were in good agreement with Drude free electron theory, which accounts for intraband absorption. The band gap of the films was found to be in the range of 3.3 to 3.5 eV and signifies the onset of interband absorption. Electrical conductivities in the 10^− 3 Ω cm range were obtained both from dc electrical measurements and from analysis of the optical measurements.     

Photo-fixation of SO2 in nanocrystalline TiO2 films prepared by reactive DC magnetron sputtering

We report on photo-fixation of SO₂ onto nanostructured TiO₂ thin films prepared by reactive DC magnetron sputtering. The films were exposed to 50 ppm SO₂ gas mixed in synthetic air and illuminated with UV light at 298 and 473 K. The evolution of the adsorbed SO_x species was monitored by in situ Fourier transform infrared specular reflection spectroscopy. Significant photo-fixation occurred only in the presence of UV illumination. The SO₂ uptake was dramatically enhanced at elevated temperatures and then produced strongly bonded surface-coordinated SO_x complexes. The total SO_x uptake is consistent with Langmuir adsorption kinetics. The sulfur doping at saturation was estimated from X-ray photoelectron spectroscopy to be ~ 2.2 at.% at 473 K. These films were pale yellowish and had an optical absorption coefficient being ~ 3 times higher than in undoped film. The S-doped films exhibit interesting oleophobic properties, exemplified by the poor adherence of stearic acid. Our results suggest a new method for sulfur doping of TiO₂ to achieve combined anti-grease and photocatalytic properties.     

Structural and electrochromic properties of TiO2 thin films prepared by metallorganic chemical vapor deposition

Titanium dioxide thin films were deposited by Metallorganic Chemical Vapor Deposition at substrate temperatures ranging from 250 °C to 450 °C over soda lime glass and indium tin oxide coated glass substrates. X-ray diffraction studies show that films have a crystalline anatase structure at all the deposition temperatures. Particle size decreases and texture changes with the increase in substrate temperature. X-ray photoelectron spectroscopy confirms the appearance of a new well resolved state in the core level of Ti 2p spectrum shifted by 1.16 eV to lower binding energy due to the reduction of Ti^+ 4 to Ti^+ 3 upon litheation. Chronoamperometery, cyclic voltammetery and in situ UV-Vis spectrophotometeric studies were carried out on the prepared samples. Particle size and crystallinity control the electrochromic performance. The 350 °C film shows the highest ion storage capacity and the highest optical modulation along with an appreciable band gap broadening.     

Hydrophilicity of anatase TiO2/Cr-doped TiO2 thin films with different band gaps

Based on the concept that the electron-hole separation effect caused by a different band-gap structure would improve its hydrophilicity, anatase-TiO₂/Cr-doped TiO₂ thin films were synthesized by DC magnetron sputtering. The optical band gaps of TiO₂ thin films decreased from 3.23 to 2.95 eV with increasing Cr-doping content. Multilayer TiO₂ thin films with different band gaps exhibited a superhydrophilicity under UV illumination. In particular, in anatase TiO₂ (3.23 eV)/4.8% Cr-doped TiO₂ (2.95 eV), the hydrophilicity, which indicated a contact angle of less than 20°, lasted for 48 h in the dark after UV illumination was discontinued. This outstanding result has rarely been reported for TiO₂ thin films, which confirmed that the prominent superhydrophilicity of anatase TiO₂/Cr-doped TiO₂/glass could be attributed to the retardation of electron-hole recombination caused by the band-gap difference.     

Thermal properties of TiO2 films grown by atomic layer deposition

We study the thermal properties of amorphous TiO₂ thin films of various thicknesses t, grown by atomic layer deposition. The thermo-optic coefficient dn/dT and the temperature coefficient dρ/dT of film density ρ are determined from ellipsometric data in wavelength range 380 < λ < 1800 nm with the Cauchy model and the Lorentz-Lorenz relation. It is found that dn/dT exhibits negative values for films with t < 150 nm and positive values for thicker films, while no significant changes in the two coefficients take place if t < 200 nm. A qualitative physical explanation based on porosity of the thin films is suggested. Films with t = 60 nm are illustrated in detail at λ = 640 nm: the room-temperature values of the coefficients are found to be dn/dT = − 3.1 × 10^− 5 °C^− 1 and dρ/dT = − 4.8 × 10^− 5g cm^− 3° C^− 1.     

Switching properties of vanadium doped TiO2 thin films prepared by magnetron sputtering

In the present work thin films of Ti-Me (where Me: V, Nb, Ta) were deposited onto glass substrates by magnetron sputtering of mosaic target in reactive oxygen plasma. The properties of the prepared thin films were studied by X-ray diffraction (XRD), electron dispersive spectroscopy, temperature-dependent electrical and optical transmission spectroscopy measurements. The structural investigations indicate that thin films were XRD-amorphous. Reversible thermoresistance effect, recorded at 52 ± 1 °C was found from electrical measurements. The prepared coatings were well transparent in the visible part of the light spectrum from ca. 350 nm.     

Substrate and Fe-doping effects on the hydrophilic properties of TiO2 thin films

Titanium dioxide films are known for their hydrophilic and photocatalytic characteristics. Increasing specific surface area and doping can enhance their photocatalytic activity and hydrophilicity. We report here results regarding the enhancement of the photocatalytic properties of titania by both controlling surface morphology and the anatase/rutile ratio. The samples were deposited on glass, indium tin oxide covered glass, and SrTiO₃ by sputtering and laser ablation techniques. Film structure and surface morphology were investigated by X-ray diffraction and atomic force microscopy. Film hydrophilicity was assessed from contact angle measurements during- and post-irradiation with UV light. The contact angle data are discussed in terms of the synergic effects of surface morphology, structure and composition of the films.     

Enhanced photocatalytic activity of silver nanoparticles modified TiO2 thin films prepared by RF magnetron sputtering

Ag-TiO₂ nanostructured thin films with silver volume fraction of 0–40% were prepared by RF magnetron sputtering. The microstructure, surface topography, and optical properties of the films were characterized by X-ray diffractometer, transmission electron microscope, and ultraviolet–visible spectrophotometer. Photocatalytic activity of the films was evaluated by light-induced degradation of methyl orange (C₁₄H₁₄N₃NaO₃S) solution using a high pressure mercury lamp as lamp-house. The relation of photocatalytic activity and silver content was studied in detail. It is found that silver content influences microstructure of TiO₂ thin films, and silver in the films is metallic Ag (Ag⁰). Photocatalytic activity of the films increases with increasing silver content up to 5 vol.% Ag and then decreases to values significantly still bigger than that of pure TiO₂ thin films. Silver nanoparticles significantly enhance the photocatalytic activity of TiO₂ films. The better separation between electrons and holes on silver modified TiO₂ thin films surface allowed more efficiency for the oxidation and reduction reactions. The enhanced photocatalytic activity was mainly attributed to the decrease of energy gap of the films and the increase of oxygen anion radicals O₂⁻ and reactive center of surface Ti³⁺ on silver modified TiO₂ thin films surface.     

Low-temperature deposition of crystallized TiO2 thin films

Crystallized TiO₂ thin films were deposited on a non-heated substrate by two methods: oxygen-ion-assisted reactive evaporation (ORE) and high-rate reactive sputtering (HRS) using two sputtering sources. When the films were deposited on an unheated glass substrate, amorphous films were initially grown on the substrate in case of both deposition methods, although an increase in oxygen-ion energy above 600 eV led to a growth of a crystallized layer on the amorphous films in the case of ORE. When the films were deposited by HRS on a crystallized TiO₂ seed layer, homo-epitaxial growth was observed, and crystallized TiO₂ films with an excellent hydrophilic property were obtained on unheated substrate. In contrast, when the films were deposited by ORE, amorphous films were initially grown on the crystallized TiO₂ seed layer in a similar manner to the deposition of films on a glass substrate, and homo-epitaxial growth was not observed. These results suggest that the large kinetic energy of titanium atoms arriving at the substrate during HRS is a key factor in promoting epitaxial growth of the TiO₂ film at low temperature.     

Characterization of inhomogeneity in TiO2 thin films prepared by pulsed dc reactive magnetron sputtering

This article discusses an analytical method for characterizations of TiO₂ thin films and determinations of the degree of their inhomogeneity. The TiO₂ films were prepared by a pulsed dc magnetron sputtering with an operating pressure as a main experimental parameter. The obtained films were primarily characterized for film crystallinity, microstructures and optical properties by spectroscopic ellipsometry. The measured ellipsometric data were analyzed by the single-, the double, and the triple-layer models in order to match with the inhomogeneous film structure proposed in the Thornton structure zone model. The results were then compared with those obtained from grazing-incidence X-ray diffraction, field-emission scanning electron microscopy and high-resolution transmission electron microscopy. The study revealed that the pulsed dc sputtered TiO₂ films could be best described by the inhomogeneous triple-layer physical model. Although the films deposited at lower operating pressure had a dense structure with a mirror-like surface topography, the films deposited at higher operating pressure had the porous structure with the rough surface and the void.     

Optical and structural properties of nanocrystalline anatase (TiO2) thin films prepared by non-aqueous sol-gel dip-coating

Anatase (TiO₂) thin films were grown by non-aqueous sol-gel dip-coating using titanium (IV) n-butoxide as precursor and 1-butanol as solvent. High withdrawal speed of 4.7 mm/s in dip-coating resulted in defect free films of 100 nm average film thickness after subsequent heat treatments. According to scanning electron microscope and X-ray diffraction measurements, the films consisted of nanocrystalline anatase with 30 nm mean crystallite size. Refractive index n(λ) and extinction coefficient k(λ) were determined over the wavelength range from 200 to 1650 nm. The optical band gap of the film material was approximately 3.2 eV. The results showed very similar optical characteristics to those that are accomplished with chemically more reactive aqueous sol-gel processes. Furthermore, it was found that in addition to porosity, coordination number of Ti atoms to nearest oxygen neighbors is likely to have a significant role in explaining differences of optical properties between bulk anatase and thin film materials of the present work.     

Fiber texture of sputter deposited molybdenum films and structural zone model

The texture orientation of 2.5, 5, and 100 nm thick Mo films grown by sputter deposition on SiO₂ membranes at room temperature has been studied quantitatively using transmission electron microscopy. The sample tilt angle dependent diffraction patterns of these films revealed a fiber texture with the [110] out-of-plane direction for all film thicknesses. Films grown at different sputtering power and substrate–target distance showed a similar texture orientation. These results would imply that the growth was in zone II, according to the microstructure classification of the structural zone model. This is in contrast to the conventional assignment of zone I for Mo deposition at room temperature based on the low Mo homologous temperature of ∼0.1. It was found that texture dispersion was reduced as the thickness of the film increased. Possible mechanisms, including energetic particles bombardment during growth, which could affect the surface mobility and texture of the films, were discussed.     

TiO2 deposition on the surface of activated fluoropolymer substrate

Anatase-structured TiO₂ films were deposited on a commercial fluorinated polymer (FEP) with a treated surface, by means of a sol-gel dip-coating technique. Two different curing temperatures were investigated and the film microstructures were characterized by X-ray diffraction, atomic force microscopy and scanning electron microscopy analyses. The prepared samples presented very high performances in terms of photocatalytic activities, analyzed by the degradation of an organic dye in a liquid medium, and of bactericidal activities, tested on Staphylococcus aureus (S. aureus, a Gram positive bacterium) and Escherichia coli (E. coli, a Gram negative bacterium).     

A simple route to synthesize nanocrystalline TiO2 films at room temperature

At room temperature, TiO₂ films were deposited by direct current pulse magnetron sputtering. Varying the O₂/Ar flow ratio, TiO₂ films with different crystalline structures and surface morphologies were obtained. X-ray diffraction spectra and atomic force microscopy showed TiO₂ films mainly existed as amorphous and crystalline structures when the O₂/Ar flow ratio was less and more than 6/14, respectively. With these results, a critical point was found at O₂/Ar = 6/14. The film growth behavior was controlled by the shadowing effect and the mixture of crystallographic orientation and grain growth effects, when the O₂/Ar flow ratio was less and more than the critical point, respectively. The present work reveals a simple way to prepare the high quality anatase phase TiO₂ films at room temperature, as well as the growth mechanism behind it.