Ga-doped ZnO transparent electrodes with TiO<Subscript>2</Subscript> blocking layer/nanoparticles for dye-sensitized solar cells

Ga-doped ZnO [GZO] thin films were employed for the transparent electrodes in dye-sensitized solar cells [DSSCs]. The electrical property of the deposited GZO films was as good as that of commercially used fluorine-doped tin oxide [FTO]. In order to protect the GZO and enhance the photovoltaic properties, a TiO₂ blocking layer was deposited on the GZO surface. Then, TiO₂ nanoparticles were coated on the blocking layer, and dye was attached for the fabrication of DSSCs. The fabricated DSSCs with the GZO/TiO₂ glasses showed an enhanced conversion efficiency of 4.02% compared to the devices with the normal GZO glasses (3.36%). Furthermore, they showed better characteristics even than those using the FTO glasses, which can be attributed to the reduced charge recombination and series resistance.     

Hydrothermal Growth and Application of ZnO Nanowire Films with ZnO and TiO2 Buffer Layers in Dye-Sensitized Solar Cells

This paper reports the effects of the seed layers prepared by spin-coating and dip-coating methods on the morphology and density of ZnO nanowire arrays, thus on the performance of ZnO nanowire-based dye-sensitized solar cells (DSSCs). The nanowire films with the thick ZnO buffer layer (~0.8–1 μm thick) can improve the open circuit voltage of the DSSCs through suppressing carrier recombination, however, and cause the decrease of dye loading absorbed on ZnO nanowires. In order to further investigate the effect of TiO₂ buffer layer on the performance of ZnO nanowire-based DSSCs, compared with the ZnO nanowire-based DSSCs without a compact TiO₂ buffer layer, the photovoltaic conversion efficiency and open circuit voltage of the ZnO DSSCs with the compact TiO₂ layer (~50 nm thick) were improved by 3.9–12.5 and 2.4–41.7%, respectively. This can be attributed to the introduction of the compact TiO₂ layer prepared by sputtering method, which effectively suppressed carrier recombination occurring across both the film–electrolyte interface and the substrate–electrolyte interface.     

Enhancement of the photoelectric performance of dye-sensitized solar cells using Ag-doped TiO<Subscript>2</Subscript> nanofibers in a TiO<Subscript>2</Subscript> film as electrode

For high solar conversion efficiency of dye-sensitized solar cells [DSSCs], TiO₂ nanofiber [TN] and Ag-doped TiO₂ nanofiber [ATN] have been extended to be included in TiO₂ films to increase the amount of dye loading for a higher short-circuit current. The ATN was used on affected DSSCs to increase the open circuit voltage. This process had enhanced the exit in dye molecules which were rapidly split into electrons, and the DSSCs with ATN stop the recombination of the electronic process. The conversion efficiency of TiO₂ photoelectrode-based DSSCs was 4.74%; it was increased to 6.13% after adding 5 wt.% ATN into TiO₂ films. The electron lifetime of DSSCs with ATN increased from 0.29 to 0.34 s and that electron recombination was reduced.     

Dye-sensitized solar cells based on double-layered TiO2 composite films and enhanced photovoltaic performance

Dye-sensitized solar cells (DSSCs) are fabricated based on double-layered composite films of TiO₂ nanoparticles and hollow spheres. The photoelectric conversion performances of DSSCs based on nanoparticles/nanoparticles (PP), hollow spheres/hollow spheres (HH), hollow spheres/nanoparticles (HP), and nanoparticles/hollow spheres (PH) double-layered films are investigated, and their photo-electric conversion efficiencies are 4.33, 4.72, 4.93 and 5.28%, respectively. The enhanced performance of TiO₂ nanoparticles/hollow spheres double-layered composite film solar cells can be attributed to the combined effect of following factors. The light scattering of overlayer hollow spheres enhances harvesting light of the DSSCs and the underlayer TiO₂ nanoparticle layer ensures good electronic contact between film electrode and the F-doped tin oxide (FTO) glass substrate. Furthermore, the high surface areas and pore volume of TiO₂ hollow spheres are respectively beneficial to adsorption of dye molecules and transfer of electrolyte solution.     

Polymer material-supported titania nanofibers with different polyvinylpyrrolidone to TiO2 ratios for degradation of vaporous trichloroethylene

Polymer-supported TiO₂ nanofibers with different polyvinylpyrrolidone (PVP)-to-TiO₂ (PT) ratios were synthesized and their photocatalytic efficiencies were examined for the decomposition of trichloroethylene (TCE). The spectral results of the TiO₂ nanofibers confirmed the presence of TiO₂ crystal phases in the nanofibers. The TiO₂ nanofiber with the highest PT ratio of 1:1.3 showed the highest TCE decomposition (94%), followed by TiO₂ nanofibers with PT ratios of 1:0.7 (91%), 1:0.35 (88%), and 1:0.1 (84%). The conditions of low input concentration and humidity were suggested for the optimal decomposition of TCE. Consequently, the TiO₂ nanofiber webs could be used effectively to decompose TCE.     

Synthesis of Nanowire TiO2 Thin Films by Hydrothermal Treatment and their Photoelectrochemical Properties

Nanowire TiO₂ thin films were successfully prepared on Ti metal substrates by hydrothermal treatment of calcined Ti foils in 10 M NaOH. The nanowire TiO₂ thin films exhibited much larger surface area and higher photoelectrochemical performance than the TiO₂ thin films prepared on Ti metal substrates by the calcination of Ti foil. These nanowire films were shown to act as an efficient photoanodes for the photoelectrochemical water splitting reaction.     

An approach to laminated flexible Dye sensitized solar cells

We have built TiO₂ Dye sensitized solar cells (DSSCs) that combined flexible TiO₂ photoanodes coated on ITO/PET substrates with a gel electrolyte based on PVDF-HFP-SiO₂ films. Titanium isopropoxide (TiP₄) was used as additive to TiO₂ nanoparticles for increasing power conversion efficiency in Dye sensitized solar cell electrodes prepared at low-temperature (130 °C). An efficiency η_AM1.5G = 3.55% on ITO/PET substrates is obtained at 48 mW/cm² illumination with a standard liquid electrolyte based on methoxypropionitrile. Among several solvents forming gels with PVDF-HFP-SiO₂, N-methyl (pyrrolidone) (NMP) was found to enable the most stable devices. A power conversion efficiency η_AM1.5G = 2% was obtained under 10 mW/cm² with flexible TiO₂-ITO-PET photoanodes and the PVDF-HFP-SiO₂ + NMP gel electrolyte.     

An efficient and low-cost TiO2 compact layer for performance improvement of dye-sensitized solar cells

A TiO₂ organic sol was synthesised for the preparation of a compact TiO₂ layer on fluorine-doped tin oxide (FTO) glass by a dip-coating technique. The resultant thin film was used for the fabrication of dye-sensitized solar cells (DSSCs). The compact layer typically has a thickness of ca. 110 nm as indicated by its SEM, and consists of anatase as confirmed by the XRD pattern. Compared with the traditional DSSCs without this compact layer, the solar energy-to-electricity conversion efficiency, short-circuit current and open-circuit potential of the DSSCs with the compact layer were improved by 33.3%, 20.3%, and 10.2%, respectively. This can be attributed to the merits brought by the compact layer. It can effectively improve adherence of TiO₂ to FTO surface, provide a larger TiO₂/FTO contact area, and reduce the electron recombination by blocking the direct contact between the redox electrolyte and the conductive FTO surface.     

Electrophoretic deposition of TiO2 film on titanium foil for a flexible dye-sensitized solar cell

Electrophoretic deposition (EPD) method is employed to obtain mesoporous TiO₂ film on a titanium (Ti) foil; the film is then mechanically compressed and sintered at 350 °C before being subjected to dyeing. A comprehensive study was made on the mechanistic aspects of the EPD process. The dye-sensitized solar cell (DSSC) using the thus formed TiO₂ film rendered a power conversion efficiency (Eff.) of 6.5%. Effects of various compression pressures on the photovoltaic parameters and on other characteristic parameters of the pertinent DSSCs are studied. Electrochemical impedance spectroscopy (EIS) is applied for the first time, using a novel equivalent model, to study the impedance behavior of the DSSC with this type of TiO₂ film. We also obtain characteristic parameters of the TiO₂ photoanode by using EIS. The coordination number of the TiO₂ film, and the ratio of charge transfer resistances of electron recombination and electron transport are also obtained and analyzed. Moreover, we employ a multilayer approach and increase the film thickness to prepare TiO₂ films with the same coordination number and porosity; DSSCs using such TiO₂ films obtained from P90 and P25 rendered efficiencies of 6.5% and 5.24%, respectively. Scanning electron microscopy (SEM) micrographs are obtained to characterize the TiO₂ films formed by the EPD technique and laser-induced transient technique is used to estimate the electron lifetime in the TiO₂ films.     

基于WO3-MoO3和TiO2/CdS复合电极的光电致变色器件

电致变色广泛应用于智能窗领域,但电致变色材料仍需外部电源驱动,将太阳能电池与电致变色材料结合起来的光电致变色器件可实现无需外部供电的智能变色调控。性能优异的变色阴极和光阳极是当下光电致变色器件的研究热点。通过水热法制备WO₃-MoO₃薄膜,研究其电致变色性能;通过水热法结合连续离子层沉积法制备TiO₂/CdS复合薄膜,研究其光电转换性能。最后将WO₃-MoO₃薄膜和TiO₂/CdS复合薄膜分别作为光电致变色器件的变色阴极、光阳极构建WO₃/MoO₃-TiO₂/CdS光电致变色器件。WO₃/MoO₃-TiO₂/CdS光电致变色器件具有较大的光学调制范围(630nm处为41.99%)、更高的着色效率(35.787%),将其作为智能窗应用在现代建筑、通行工具等领域具有重要应用价值。     

Dye-sensitized solar cells based on electrospun poly(vinylidenefluoride-co-hexafluoropropylene) nanofibers

Poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) nanofibers were prepared by the electrospinning method and used as polymer electrolytes in dye-sensitized solar cells (DSSCs). The electrolyte uptake and ionic conductivity of electrospun PVDF-HFP nanofibers with different diameters changed significantly, regardless of the nanofiber thickness. The PVDF-HFP nanofibers prepared from a 15 wt% spinning solution showed high ionic conductivity (1.295 S/cm) and electrolyte uptake (947 %). DSSCs based on the 15 wt% PVDF-HFP nanofiber electrolyte showed an electron transit time of 6.34 × 10^?3 s, electronic recombination time of 5.88 × 10^?2 s, and conversion efficiency of 3.13 %. Thus, we concluded that the electrospun PVDF-HFP nanofibers can be used as polymer electrolytes in flexible DSSCs as well.     

Plasmon-enhanced quasi-solid-state dye-sensitized solar cells with metal@Dendron nanoparticles

We have investigated the effects of localized surface plasmons (LSPs) on the performance of quasi-solid-state dye-sensitized solar cells (DSSCs). Ag and Au nanoparticles (NPs) were prepared by photoreduction in the presence of generation 5 polyester hydroxyl acetylene bis(hydroxymethyl)propanoic acid dendrons (Dendron) as a stabilizer. The plasmon-enhanced DSSCs were achieved by incorporating metal@Dendron NPs into TiO₂ photoanodes. The presence of dendrons prevents the photoelectrons from recombining on the surface of TiO₂ semiconductor and improves the stability of metal NPs. With the addition of Ag@Dendron NPs, the photocurrent and the power conversion efficiency of quasi-solid-state DSSCs increased due to the LSP effect of metal NPs and the barrier effect of dendron, which were confirmed by the increased incident photon-to-photocurrent efficiency and by electrochemical impedance spectroscopy analysis.     

Fabrication and photoelectrochemical properties of TiO2 films on Ti substrate for flexible dye-sensitized solar cells

The dye-sensitized solar cells (DSSCs) using Ti foil supporting substrate for fabricating nanocrystalline TiO₂ flexible film electrodes were developed, intending to improve the photoelectrochemical properties of flexible substrate-based DSSCs. The obtained cells were characterized by electrochemical impedance spectra (EIS), open circuit voltage decay (OCVD) measurement and Tafel plots. The experimental results indicate that the most important advantage of a Ti foil-based TiO₂ flexible electrode over a FTO glass-based electrode lies in its reduced sheet resistance, electron traps, and the retarded back reaction of electrons with tri-iodine ions in DSSCs. All above characteristics for the Ti substrate TiO₂ films are beneficial for decreasing the charge recombination in the TiO₂ electrode and prolonging the electron lifetimes for the DSSCs, as well as improvement of the overall solar conversion efficiency. The photocurrent of the cell fabricated with the Ti foil-based flexible electrode increased significantly, leading to a much higher overall solar conversion efficiency of 5.45% at 100 mW/cm² than the cell made with FTO glass-based TiO₂ electrodes. Above results demonstrate that Ti foil is a potential alternative to the conventional FTO glass substrate for the DSSCs.     

Enhanced photocatalytic activity of electrospun TiO2/ZnO nanofibers with optimal anatase/rutile ratio

The photocatalytic characteristics of the TiO₂/ZnO nanofibers synthesized by electrospinning followed by calcinating at different temperatures to alter the anatase-to-rutile ratio are investigated. The results demonstrate that the photocatalytic activity of TiO₂/ZnO nanofibers is enhanced by optimizing the anatase/rutile ratio among the trade-off effects of the band-gap energy, the electron/hole recombination rate, and the surface area. When calcined at 650 °C, the TiO₂/ZnO nanofibers with optimal anatase/rutile ratio (48:52) balancing these trade-off effects have the highest photocatalytic efficiency both in the degradation of RhB in liquid and conversion of NO gas.     

Effect of compressed TiO2 nanoparticle thin film thickness on the performance of dye-sensitized solar cells

In this study, dye-sensitized solar cells (DSSCs) were fabricated using nanocrystalline titanium dioxide (TiO₂) nanoparticles as photoanode. Photoanode thin films were prepared by doctor blading method with 420 kg/cm² of mechanical compression process and heat treatment in the air at 500°C for 30 min. The optimal thickness of the TiO₂ NP photoanode is 26.6 μm with an efficiency of 9.01% under AM 1.5G illumination at 100 mW/cm². The efficiency is around two times higher than that of conventional DSSCs with an uncompressed photoanode. The open-circuit voltage of DSSCs decreases as the thickness increases. One DSSC (sample D) has the highest conversion efficiency while it has the maximum short-circuit current density. The results indicate that the short-circuit current density is a compromise between two conflict factors: enlargement of the surface area by increasing photoanode thickness and extension of the electron diffusion length to the electrode as the thickness increases.     

Growth of Comb-like ZnO Nanostructures for Dye-sensitized Solar Cells Applications

Dye-sensitized solar cells (DSSCs) were fabricated by using well-crystallized ZnO nanocombs directly grown onto the fluorine-doped tin oxide (FTO) via noncatalytic thermal evaporation process. The thin films of as-grown ZnO nanocombs were used as photoanode materials to fabricate the DSSCs, which exhibited an overall light to electricity conversion efficiency of 0.68% with a fill factor of 34%, short-circuit current of 3.14 mA/cm², and open-circuit voltage of 0.671 V. To the best of our knowledge, this is first report in which thin film of ZnO nanocombs was used as photoanode materials to fabricate the DSSCs.     

A natural tomato slurry as a photosensitizer for dye-sensitized solar cells with TiO2/CuO composite thin films

We have studied the performance of dye-sensitized solar cells by employing natural dye “anthocyanins” extracted from the tomato slurry as a sensitizer for the TiO₂/CuO photoanode. The extracts were anchored on TiO₂/CuO films deposited on an ITO substrate which was used as a photoanode. The dye adsorbed TiO₂/CuO films electrode, the copper plate as a counter electrode, and iodolyte as an electrolyte were assembled into DSSCs. The conversion efficiency of the DSSCs was found to be 2.96% with a V_OC of 0.615 V, J_SC of 6.6 mA/cm², and an FF of 0.73. This work highlights the use of contribution of the tomato slurry as a natural sensitizer to enhance the efficiency of DSSCs.     

Efficient Performance of Electrostatic Spray-Deposited TiO2 Blocking Layers in Dye-Sensitized Solar Cells after Swift Heavy Ion Beam Irradiation

A compact TiO₂ layer (~1.1 μm) prepared by electrostatic spray deposition (ESD) and swift heavy ion beam (SHI) irradiation using oxygen ions onto a fluorinated tin oxide (FTO) conducting substrate showed enhancement of photovoltaic performance in dye-sensitized solar cells (DSSCs). The short circuit current density (J_sc = 12.2 mA cm^-2) of DSSCs was found to increase significantly when an ESD technique was applied for fabrication of the TiO₂ blocking layer, compared to a conventional spin-coated layer (J_sc = 8.9 mA cm^-2). When SHI irradiation of oxygen ions of fluence 1 × 10¹³ ions/cm² was carried out on the ESD TiO₂, it was found that the energy conversion efficiency improved mainly due to the increase in open circuit voltage of DSSCs. This increased energy conversion efficiency seems to be associated with improved electronic energy transfer by increasing the densification of the blocking layer and improving the adhesion between the blocking layer and the FTO substrate. The adhesion results from instantaneous local melting of the TiO₂ particles. An increase in the electron transport from the blocking layer may also retard the electron recombination process due to the oxidized species present in the electrolyte. These findings from novel treatments using ESD and SHI irradiation techniques may provide a new tool to improve the photovoltaic performance of DSSCs.     

Multi-functional 3D N-doped TiO<Subscript>2</Subscript> microspheres used as scattering layers for dye-sensitized solar cells

Three-dimensional TiO₂ microspheres doped with N were synthesized by a simple single-step solvothermal method and the sample treated for 15 h (hereafter called TMF) was then used as scattering layers in the photoanodes of dye-sensitized solar cells (DSSCs). The TMF was characterized using scanning electron microscopy, high resolution transmission electron microscopy, Brunauer-Emmett-Teller measurements, X-ray diffraction, and X-ray photoelectron spectroscopy. The TMF had a high surface area of 93.2 m²?g^–1 which was beneficial for more dye-loading. Five photoanode films with different internal structures were fabricated by printing different numbers of TMF scattering layers on fluorine-doped tin oxide glass. UV-vis diffuse reflection spectra, incident photon-to-current efficiencies, photocurrent-voltage curves and electrochemical impedance spectroscopy were used to investigate the optical and electrochemical properties of these photoanodes in DSSCs. The presence of nitrogen in the TMF changed the TMF microstructure, which led to a higher open circuit voltage and a longer electron lifetime. In addition, the presence of the nitrogen significantly improved the light utilization and photocurrent. The highest photoelectric conversion efficiency achieved was 8.08%, which is much higher than that derived from typical P25 nanoparticles (6.52%).

Open image in new window

     

The role of TiO2 addition in ZnO nanocrystalline thin films: Variation of photoelectrochemical responsivity

In this study, the effects of TiO₂ addition on the physical and photoelectrochemical properties of ZnO thin films have been investigated. The (TiO₂)_x–(ZnO)_1−x nanocomposite thin films were dip-coated on both glass and indium tin oxide (ITO)-coated conducting glass substrates with various values of x, specifically 0, 0.05, 0.1, 0.25 and 0.5. Optical properties of the samples were studied by UV–vis spectrophotometry in the range of 300–1100 nm. The optical spectra of the nanocomposite thin films showed high transparency in the visible region. The optical bandgap energy of the (TiO₂)_x–(ZnO)_1−x films increased slightly with increasing values of x. The crystalline structure of the nanocomposite films was investigated by X-ray diffraction, which indicated the formation of ZnO nanocrystals in the thin films with x < 0.5. Moreover, the crystallinity of the films decreased with increasing values of x. The surface chemical composition of the samples was investigated by X-ray photoelectron spectroscopy (XPS), which revealed stoichiometric ZnO and TiO₂ on the surfaces of the films. The photoelectrochemical properties of the samples were also characterized using a high-pressure xenon light source and KOH electrolyte. The addition of 10 mol% (x = 0.1) TiO₂ to the ZnO thin films resulted in the best photoresponse in the visible region of the solar spectrum. In addition, the effect of TiO₂ concentration on the electrical properties and the flat-band potential of the (TiO₂)_x–(ZnO)_1−x system was studied by impedance spectroscopy; x = 0.1 exhibited the highest donor density and charge-transfer resistance.