Electrospun nanofibers of block copolymer of trimethylene carbonate and ϵ‐caprolactone

The electrospinning behavior of a block copolymer of trimethylene carbonate (TMC) and ε‐caprolactone dissolved in N,N‐dimethylformamide (DMF) and methylene chloride (MC) was studied. The effects of the blended solvent volume ratio, concentration, voltage, and tip–collector distance (TCD) on the morphology of the electrospun fibers were investigated by scanning electron microscopy. The results indicated that the diameter of the electrospun fibers decreased with a decreasing molar ratio of MC to DMF, but beads formed gradually. With a decreasing concentration of the solution, the fiber diameter decreased; at the same time, beads also appeared and changed from spindlelike to spherical. A higher voltage and larger TCD favored the formation of smaller diameter electrospun fibers. The results of differential scanning calorimetry and X‐ray diffraction showed that the crystallinity and melting point of the electrospun fibers decreased when increasing the TMC content in the copolymer. Compared with the corresponding films, the crystallinity and melting point of the electrospun fibers were obviously increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1462–1470, 2006     

Synthesis of trimethylene carbonate/ϵ‐caprolactone copolymers initiated with zinc alkoxide: influence of copolymer chain microstructure on thermal and mechanical properties

Ethylzinc(II ) ethoxide is a highly active and efficient initiator for the bulk polymerization of 1,3‐trimethylene carbonate and its copolymerization with ? ‐caprolactone. This initiator allows one to obtain (co)polymers with high molar masses in quite a short time. Significant difference in co‐monomer reactivity and relatively low participation of intermolecular transesterification processes lead to the obtained copolymers being characterized by a gradient chain microstructure. In ¹³C NMR spectra, in all regions, we observed the presence of triads which were distinctly represented by four peaks for the carbonyl signal. Mechanical tests showed that copolymers containing 70% and more of ? ‐caprolactone presented a relatively high Young's modulus and a very high maximum elongation factor; therefore these materials are promising in many biomedical applications. Due to the high reaction rate, we also made an attempt at copolymerization using reactive extrusion which gave promising results. © 2017 Society of Chemical Industry     

Random copolymers based on trimethylene carbonate and ε‐caprolactone for implant applications: Synthesis and properties

Random copolymers of trimethylene carbonate (TMC) and ε‐caprolactone (CL) have been synthesized by ring‐opening polymerization of TMC and CL in the presence of stannous octoate. The effects of feeding dose, reaction temperature and polymerization time, and effect of catalyst content on the copolymerization were investigated. The results showed that the composition of the copolymers was in good agreement with the feeding dose, and the molecular weight of the copolymers decreased firstly with increasing CL content and then increased. The decrease in the reaction temperature, polymerization time and catalyst content would increase the molecular weight of the copolymers. Furthermore, the feeding dose affected the thermal and mechanical properties of the copolymer largely, and the possessing different properties of random copolymers could be obtained by adjusting the copolymer compositions. This work could optimize the polymerization conditions to achieve the copolymers with controlled properties for implant applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Homoleptic lanthanide amidinate complexes: A single‐component initiator for ring‐opening polymerization of trimethylene carbonate and copolymerization with ϵ‐caprolactone

The ring‐opening polymerization of trimethylene carbonate (TMC) using homoleptic lanthanide amidinate complexes [CyNC(R)NCy]₃Ln as single component initiators has been fully investigated for the first time. The substituents on amidinate ligands and center metals show great effect on the catalytic activities of these complexes, that is, Me > Ph, and La > Nd > Sm > Yb. Among them, [CyNC(Me)NCy]₃La shows the highest catalytic activity. Some features of the TMC polymerization initiated by [CyNC(Me)NCy]₃La were studied in detail. A mechanism that the polymerization occurs via acyl‐oxygen bond cleavage rather than alkyl‐oxygen bond cleavage was proposed. The copolymerization of TMC with ?‐caprolactone initiated by [CyNC(Me)NCy]₃La was also tested. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 22–28, 2006     

Synthesis of functionalizable and biodegradable polymers via ring‐opening polymerization of 5‐benzyloxy‐trimethylene carbonate and ε‐caprolactone

The biomedical applications of poly(ε‐caprolactone) (PCL) were limited for its high hydrophobicity and crystallinity. In this study, we copolymerized CL with amorphous 5‐hydroxyl‐trimethylene carbonate (HTMC) to solve the problem. The 5‐benzyloxy‐trimethylene carbonate (BTMC) was synthesized to copolymerize with CL, then hydrogenolyzed to obtain hydroxyl pendant groups. A serial of copolymers with different BTMC molar ratio were synthesized and their chemical structures and thermal properties were thoroughly studied with NMR, FT‐IR, GPC, XRD, DSC, and TGA. Finally we examined the water contact angle of the copolymers. DSC and XRD results showed that the PCL segments in the copolymers crystallized below 16.8%. BTMC molar content and the crystallinity of the copolymers increased after hydrolysis. With the introduced hydroxyl pendant groups, the deprotected copolymers improved their hydrophilic property significantly, and the copolymer with 9.3% HTMC molar content had static water contact angle as low as 36.5°. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol) block copolymers prepared by a salicylaldimine‐aluminum complex

A series of poly(?‐caprolactone)‐b‐poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights were synthesized with a salicylaldimine‐aluminum complex in the presence of monomethoxy poly(ethylene glycol). The block copolymers were characterized by ¹H NMR, GPC, WAXD, and DSC. The ¹H NMR and GPC results verify the block structure and narrow molecular weight distribution of the block copolymers. WAXD and DSC results show that crystallization behavior of the block copolymers varies with the composition. When the PCL block is extremely short, only the PEG block is crystallizable. With further increase in the length of the PCL block, both blocks can crystallize. The PCL crystallizes prior to the PEG block and has a stronger suppression effect on crystallization of the PEG block, while the PEG block only exerts a relatively weak adverse effect on crystallization of the PCL block. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of a random terpolymer of L‐lactide, ϵ‐caprolactone and glycolide

A random terpolymer of L ‐lactide (LL), ?‐caprolactone (CL) and glycolide (G) has been synthesized in bulk at 130 °C using stannous octoate as the coordination–insertion initiator. The terpolymer, poly(LL‐ran‐CL‐ran‐G), has been characterized by a combination of analytical techniques: GPC, ¹H NMR, ¹³C NMR, DSC and TG. Molecular weight characterization by GPC shows a unimodal molecular weight distribution with values of M _n = 1.01 × 10⁵ g mol^?1 and M _w / M _n = 2.17. Compositional and microstructural analysis by ¹H NMR and ¹³C NMR, respectively, reveal a terpolymer composition of LL:CL:G = 74:15:11 (mol%) with a chain microstructure consistent with random monomer sequencing. This latter view is supported by the terpolymer temperature transitions (T_g and T_m) from DSC and the thermal decomposition profile from TG. The results and, in particular, the conclusion that it is a random rather than a statistical terpolymer are discussed in the light of current theories regarding the mechanism of this type of polymerization. © 2001 Society of Chemical Industry     

Polymerization of ϵ‐caprolactone with maleic anhydride: Synthesis and characterization

High‐molecular‐weight polymers of ϵ‐caprolactone (CL) and maleic anhydride (MA) with anhydride group content of about 1% wt have been synthesized and studied. The polymerization reaction was carried out in bulk under nitrogen atmosphere. Stannous octoate (Sn(oct)₂), and 2,2'‐azobisisobutyronitrile (AIBN) were used as a catalyst and an initiator, respectively. A two‐level design of experiments was used to study the effect of various conditions on the characteristics of the copolymer. Reaction time, temperature, and concentration ratio of various reactants (two monomers, monomer to catalyst, and monomer to initiator) were the independent variables used, and the dependent variables included the molecular weight and the anhydride content in the polymer. Nuclear magnetic resonance (NMR) studies indicate that the succinic anhydride units were incorporated individually either to the polymer chain end or backbone. Anhydride content in the polymer and gel permeation chromatograph (GPC) studies indicate that the maleic anhydride acts as the true initiating species rather than as a comonomer in the system. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3189–3194, 2000     

Preparation and characterization of biodegradable poly(ϵ‐caprolactone) self‐reinforced composites and their crystallization behavior

Self‐reinforced poly(?‐caprolactone) (PCL) composites were prepared by dispersing a homologous nucleating agent within the PCL matrix through melt mixing. Coalesced PCL, featuring more orderly chain arrangements, acted as the nucleating agent leading to improvement of crystallization for the melt PCL matrix. Non‐isothermal melt crystallization behavior, isothermal melt crystallization kinetics, spherulitic morphology and the crystal structure of neat PCL and the PCL self‐reinforced composites were studied in detail. The results indicated that both non‐isothermal and isothermal melt crystallization of PCL composites were enhanced significantly by the homologous nucleating agent, while the crystallization mechanism and crystal structures remained unchanged. The results of tensile mechanical tests showed that the Young's modulus of the composites was improved by up to 77% with the incorporation of 20 wt% nucleating agent. Biocompatibility tests demonstrated that the cells could adhere to and proliferate well on the surface of the self‐reinforced PCL composites. © 2017 Society of Chemical Industry     

Random copolymerization of ϵ-caprolactone and trimethylene carbonate with rare earth catalysts

Random copolymerization of trimethylene carbonate (TMC) with ϵ-caprolactone (CL) catalyzed by rare earth chloride-epoxide or rare earth isopropoxide has been investigated for the first time. It was found that in the presence of epoxide, rare earth chlorides have high activities for the copolymerization, giving high-molecular-weight random copolymer P(CL-co-TMC) with a narrow molecular weight distribution. Light rare earth chloride-propylene oxide systems are more effective for the copolymerization than heavy rare earth chloride-propylene oxide systems. For the rare earth chloride-epoxide catalyst system, epoxide is the requisite component, and its amount affects the catalytic activity; while rare earth isopropoxide can catalyze the copolymerization alone. The preparative conditions of the copolymer with NdCl₃-5PO system were studied. The reactivity ratios of CL and TMC copolymerization with NdCl₃-5PO determined by Fineman-Ross method are 1.60 for r_TMC and 0.72 for r_CL, respectively. The copolymers were characterized by ¹H- and ¹³C-NMR, GPC, and DSC. The mechanism study shows that the rare earth alkoxide is the active species that initiates the ring opening copolymerization of CL and TMC with acyl-oxygen bond cleavages of the monomers. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 2131–2139, 1997     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of polycyanurate networks modified by oligo(ϵ‐caprolactone) as precursors of porous thermosets

Oligo(?‐caprolactone)‐modified polycyanurate networks were synthesized by thermal polycyclotrimerization of dicyanate ester of bisphenol E in the presence of a dihydroxy‐telechelic poly(?‐caprolactone) (PCL) oligomer with varying compositions. Using FTIR, gel fraction content and density measurements, it has been proved that the main part of the reactive modifier was chemically incorporated into the PCN network structure. According to the thermal behavior of the polymer networks as investigated by TGA, they can be divided into two groups. The first group of systems with low modifier content (i.e., up to 20 wt %) is characterized by one stage of decomposition under nitrogen, and two stages under oxygen. A second group of systems with higher modifier content is generally characterized by two stages of decomposition in nitrogen and three stages in oxygen. DSC and DMTA investigations have shown the occurrence of at least a two‐phase structure in all the samples. The PCN/PCL‐based hybrid networks can be effectively used as precursors for the generation of porous PCN thermosets, as evidenced by FTIR and SEM. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Development of new poly(ϵ‐caprolactone)/chitosan films

This study reports for the first time the production of poly(?‐caprolactone)/chitosan (PCL/CHT) films by solvent casting using a mixture of formic acid/acetone (70:30 vol%). Both uncrosslinked and crosslinked films with the natural crosslinker genipin were developed. The mechanical properties of the samples were analyzed by dynamical mechanical analysis (DMA) in the hydrated state. DMA was also successfully used for the first time to monitor in situ the crosslinking process as a function of time and crosslinker concentration. The compatibility between the polymers in the blended films was analyzed by Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC). It was found that phase distribution is highly dependent on the blend composition. The developed films could potentially be used in different applications, such as tissue engineering scaffolds. © 2013 Society of Chemical Industry     

A comparative study of poly(l‐lactide)‐block‐poly(ϵ‐caprolactone) six‐armed star diblock copolymers and polylactide/poly(ϵ‐caprolactone) blends

This paper deals with the synthesis of a series of six‐armed star diblock copolymers based on poly(l ‐lactide) (PLLA) and poly(?‐caprolactone) (PCL) by ring‐opening polymerization using stannous octoate as catalyst and the preparation of polylactide (PLA)/PCL linear blends using a solution blending technique, while keeping the PLA‐to‐PCL ratio comparable in both systems. The thermal, rheological and mechanical properties of the copolymers and the blends were comparatively studied. The melting point and the degree of crystallinity were found to be lower for the copolymers than the blends due to poor folding property of star copolymers. Dynamic rheology revealed that the star polymers have lower elastic modulus, storage modulus and viscosity as compared to the corresponding blends with similar composition. The blends show two‐phase dispersed morphology whereas the copolymers exhibited microphase separated morphology with elongated (worm‐like) microdomains. The crystalline structures of the copolymers were characterized by larger crystallites than their blend counterparts, as estimated using Sherrer's equation based on wide‐angle X‐ray diffraction data. © 2016 Society of Chemical Industry     

The ageing of poly(ϵ‐caprolactone)

Partially crystallized poly(?‐caprolactone) has been stored for up to 6 months at various temperatures from ?18 to 50 °C and the change in tensile properties, crystallinity and melting behaviour followed with storage time. The Young modulus, yield and drawing stress were observed to increase with time and at a rate which increased with storage temperature. These changes in tensile properties could be accounted for by the increase in crystallinity and were attributed to a thickening of the lamellae which reinforced the morphology and increased the stiffness of the polymer. The thickening of the lamellae accounted for the shift of the melting endotherms to higher temperatures with time. The stem lengths increased with the square root of the storage time and the rate increased with temperature corresponding to an activation energy of 40 ± 5 kJ mol^?1. It is considered that ageing occurred by a process of secondary crystallization by extension of the ‘fold surface’ into the adjacent melt and the thickening of the lamellae. The time dependence of growth can only be explained by small segments of the chain being incorporated onto the crystal on the time scale of the local segmental mobility which is independent of chain entanglements. This does not have the characteristics of a nucleation controlled process but is a thermally activated diffusion process the rate of which increases with temperature. © 2015 Society of Chemical Industry     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization behavior of poly(ϵ‐caprolactone) in poly(ϵ‐caprolactone) and poly(vinyl methyl ether) mixtures

The morphological development and crystallization behavior of poly(?‐caprolactone) (PCL) in miscible mixtures of PCL and poly(vinyl methyl ether) (PVME) were investigated by optical microscopy as a function of the mixture composition and crystallization temperature. The results indicated that the degree of crystallinity of PCL was independent of the mixture composition upon melt crystallization because the glass‐transition temperatures of the mixtures were much lower than the crystallization temperature of PCL. The radii of the PCL spherulites increased linearly with time at crystallization temperatures ranging from 42 to 49°C. The isothermal growth rates of PCL spherulites decreased with the amount of the amorphous PVME components in the mixtures. Accounting for the miscibility of PCL/PVME mixtures, the radial growth rates of PCL spherulites were well described by a kinetic equation involving the Flory–Huggins interaction parameter and the free energy for the nuclei formation in such a way that the theoretical calculations were in good agreement with the experimental data. From the analysis of the equilibrium melting point depression, the interaction energy density of the PVME/PCL system was calculated to be ?3.95 J/cm³. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Kinetics of microwave‐assisted polymerization of ϵ‐caprolactone

The kinetics of polymerization of ?‐caprolactone (CL) in bulk was studied by irradiating with microwave of 350 W and frequency of 2.45 GHz with different cycle‐heating periods (30–50 s). The molecular weight distributions were determined as a function of reaction time by gel permeation chromatography. Because the temperature of the system continuously varied with reaction time, a model based on continuous distribution kinetics with time/temperature‐dependent rate coefficients was proposed. To quantify the effect of microwave on polymerization, experiments were conducted under thermal heating. The polymerization was also investigated with thermal and microwave heating in the presence of zinc catalyst. The activation energies determined from temperature‐dependent rate coefficients for pure thermal heating, thermally aided catalytic polymerization, and microwave‐aided catalytic polymerization were 24.3, 13.4, and 5.7 kcal/mol, respectively. This indicates that microwaves increase the polymerization rate by lowering the activation energy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1450–1456, 2004     

Synthesis,characterization and crosslinking of functional star‐shaped poly(ε‐caprolactone)

Star‐shaped low molecular weight poly(ε‐caprolactone)s (PCLs) were synthesized and functionalized with crosslinkable terminal groups for subsequent crosslinking. The ε‐caprolactone (CL) prepolymers were polymerized by ring‐opening in the presence of polyglycerine (PGL) as an initiator (1, 3 and 5 mol%) and Sn(II)2‐ethylhexanoate as a catalyst. Characterization of the prepolymer by ¹³C/¹H nuclear magnetic resonance (NMR) spectroscopy, size exclusion chromatography (SEC), differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR) revealed a six‐armed star‐shaped structure for the prepolymer with the molecular weight controlled by the ratio of PGL and CL. Functionalization of the hydroxyl‐terminated prepolymer was carried out with maleic or itaconic anhydride. In both cases, the characterization of the functionalized prepolymer showed that the hydroxyl groups were completely substituted. The functionalized PCLs were successfully crosslinked through the reaction of double bonds. The crosslinking was induced either thermally with organic peroxide or photochemically with a photosensitive initiator. Characterization of the crosslinked PCLs by Soxhlet extraction, DSC and FTIR showed that the itaconic double bond was much more reactive in thermal crosslinking than the maleic double bond. Thus, the crosslinked prepolymers that were functionalized with itaconic double bonds achieved a gel content of about 90%. A gel content of 100% was achieved with several compositions where crosslinking agents were employed. © 2002 Society of Chemical Industry