Effect of hydrated fillers and red phosphorus on the limiting oxygen index of poly(ethylene‐co‐vinyl actate)‐poly(vinyl butyral) and low density polyethylene‐poly(ethylene‐co‐vinyl alcohol) blends

The limiting oxygen index (LOI) values of EVA‐PVB and low density polyethylene (LDPE)‐poly(ethylene‐co‐vinyl alcohol) (EVOH) polymer blends containing hydrated filler‐type flame retardants and red phosphorus were measured. When used as the sole flame retardant, magnesium hydroxide [Mg(OH)₂] and alumina trihydrate (ATH) performed best in EVA and PVB, respectively. Magnesium hydroxide addition had a limited effect on the LOI of plasticized PVB, and addition of red phosphorus made little difference. This result is attributed to a mismatch between the decomposition temperature of Mg(OH)₂ and the temperature at which the PVB plasticizer vaporizes. Otherwise, low‐level addition of red phosphorus significantly improved LOI values. The presence of hydroxyl groups on the polymer backbone had a beneficial effect with respect to LOI values in ATH‐filled blends. An LOI value of 30 was achieved in EVOH with as little as 32% of ATH and 3% of red phosphorus. J. VINYL ADDIT. TECHNOL., 2008. © 2008 Society of Plastics Engineers     

Relative strength of H‐bonding groups on biodegradable polymer‐based blends in solution

The intermolecular hydrogen bonding interactions between poly(3‐hydroxybutyrate) and poly(styrene‐co‐vinyl phenol) copolymers with mutual solvent epichlorohydrin were thoroughly investigated by steady‐state fluorescence and viscosity techniques. Fluorescence spectroscopy along with viscosity technique was used to asses the intermolecular hydrogen bonding between poly‐(3‐hydroxybutyrate) and its blends with five copolymer samples of styrene–vinyl phenol, containing different proportions of vinyl phenol but similar average molecular weight and polydispersity index. In the case of very low OH contents (2–4 mol %), as expected, both components of poly(3‐hydroxybutyrate) and poly(styrene‐co‐4‐vinylphenol) chains are well separated and remain so independently of the mixed polymer ratio and overall polymer concentration as well. Conversely, when the OH content reaches 5.8 mol % or more, a significant decrease of the intrinsic fluorescence intensity emitted by the copolymer is detected upon addition of aliquots of poly(3‐hydroxybutyrate). In these cases, an average value for the interassociation equilibrium constant, K_A = 8.7, was obtained using a binding model formalism. A good agreement of these results with those obtained from complementary viscosity measurements, through the interaction parameter, Δb, was found. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 900–910, 2006     

Autonomic self‐healing of poly(vinyl butyral)

The self‐healing behavior of poly(vinyl butyral) (PVB) is evaluated below the glass transition temperature T_g. It is found that PVB shows autonomic self‐healing even at room temperature, although T_g is around at 76°C. Furthermore, a large amount of water is found to be adsorbed on the surface of the film. This is attributed to the surface localization of hydroxyl group in PVB, which is confirmed by X‐ray photoelectron spectroscopy. Since the surface is plasticized by water, the scar applied by a razor blade is healed even in the glassy state of the bulk. Moreover, the healing efficiency is enhanced at high humidity condition, owing to the pronounced plasticizing effect by water. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42008.     

Electro–optic studies on polymer‐dispersed liquid crystal composite films. I. Composites of PVB–E7

The electro‐optic performance characteristic of polymer‐dispersed liquid crystal (PDLC) composite films out of poly(vinyl butyral) (PVB) and nematic liquid crystal (E7) have been studied for a wide range of PVB–E7 composite compositions (20–70 wt % of E7). Composites were prepared by solvent casting from chloroform at room temperature. A scanning electron microscopy study showed that a E7 phase is continuously embedded in chink‐like structure of PVB matrix. Optical transmittance of the composite films (of 60 and 70 wt % loading of E7) under an alternating current (ac) electric field (0–250, V_p‐p) and frequency (50 Hz to 1 KHz) were measured employing He Ne laser (λ = 632.8 nm). The results indicate that the (PVB–E7) composite exhibits a memory effect. In the memory state, higher transmittance is preserved without applying voltage. The memory state can be erased and changed to the scattering Off‐state by heating the film to the clearing temperature of the liquid crystal. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3485–3491, 1999     

Poly(acrylonitrile‐co‐vinyl acetate)/Ag composite microspheres: One‐pot fabrication and application as catalyst

Waxberry‐like poly(acrylonitrile‐co‐vinyl acetate)/Ag composite microspheres have been prepared simply and directly via a one‐step self‐assembly approach. The morphology, formation, and catalytic activity of the as‐prepared composite microspheres are further investigated. The difference in the solubility among different segments of poly(acrylonitrile‐co‐vinyl acetate) is the basis of the formation of poly(acrylonitrile‐co‐vinyl acetate) microspheres, while the ? CN groups on the surface of poly(acrylonitrile‐co‐vinyl acetate) microspheres play an important role in the growth process from poly(acrylonitrile‐co‐vinyl acetate) microsphere to poly(acrylonitrile‐co‐vinyl acetate)/Ag composite microsphere. It is found that bulk quantities of composite microspheres with high density of Ag nanoparticles on the surface can be obtained readily by controlling the concentration of AgNO₃. The as‐prepared composite microsphere exhibits excellent catalytic activity on reduction of p‐nitrophenol. This study may shed some light on the self‐assembly of other metal/polymer composite microspheres. POLYM. ENG. SCI., 50:1767–1772, 2010. © 2010 Society of Plastics Engineers     

Thiol–ene addition enables tailored synthesis of poly(2‐oxazoline)‐graft‐poly(vinyl pyrrolidone) copolymers for binder jetting 3D printing

The continued interest in graft copolymer architectures arises from their unique solution properties and potential for a myriad of applications ranging from drug delivery to adhesives. Poly(vinyl pyrrolidone) (PVP) represents a popular amorphous, water‐soluble polymer used as a polymeric binder in binder jetting additive manufacturing, as fillers in cosmetic products, and for subcutaneous drug delivery systems. This report describes the synthesis of poly(2‐oxazoline) and PVP graft copolymers using a ‘grafting to’ methodology with an efficient thiol–ene ‘click’ reaction. Copolymerization of 2‐methyl‐2‐oxazoline and 2‐(3‐butenyl)‐2‐oxazoline introduced pendent vinyl grafting sites with a predictable absolute number‐average molecular weight. In parallel, reversible addition‐fragmentation chain‐transfer polymerization and subsequent aminolysis yielded well‐defined, oligomeric, thiol‐terminated PVP. Thiol–ene click chemistry enabled the formation of poly(2‐oxazoline)‐graft‐poly(vinyl pyrrolidone) (PMeOx‐g‐PVP) copolymers with varying mole percent grafting sites and PVP graft length. ¹H NMR spectroscopy, aqueous SEC with multiangle light scattering (SEC‐MALS), and bromine titrations confirmed chemical structure, and DSC with TGA elucidated thermal transitions. Aqueous SEC‐MALS and ¹H NMR spectroscopy also determined absolute number‐ and weight‐average molecular weights and average grafting levels, which revealed optimal reaction conditions. Zero‐shear viscosities of 5 and 10 wt% solutions in deionized water for each graft copolymer compared to their linear analogs demonstrated a significant (ca 31%) decrease in viscosity at the same number‐average molecular weight. This decrease in solution viscosity suggested PMeOx‐g‐PVP copolymers as exceptional alternatives to linear analogs for aqueous‐based, binder jetting additive manufacturing.     

Synthesis of poly[(2‐oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether‐co‐N‐phenylmaleimide] and its miscibility in blends with styrene‐acrylonitrile or poly(vinyl chloride)

The aim of the study was to investigate the synthesis of a copolymer bearing cyclic carbonate and its miscibility with styrene/acrylonitrile copolymer (SAN) or poly(vinyl chloride) (PVC). (2‐Oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether (OVE) as a monomer was synthesized from glycidyl vinyl ether and CO₂ using quaternary ammonium chloride salts as catalysts. The highest reaction rate was observed when tetraoctylammonium chloride (TOAC) was used as a catalyst. Even at the atmospheric pressure of CO₂, the yield of OVE using TOAC was above 80% after 6 h of reaction at 80°C. The copolymer of OVE and N‐phenylmaleimide (NPM) was prepared by radical copolymerization and was characterized by FTIR and ¹H‐NMR spectroscopies and differential scanning calorimetry (DSC). The monomer reactivity ratios were given as r₁ (OVE) = 0.53–0.57 and r₂ (NPM) = 2.23–2.24 in the copolymerization of OVE and NPM. The films of poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were cast from N‐dimethylformamide. An optical clarity test and DSC analysis showed that poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were both miscible over the whole composition range. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1809–1815, 2000     

pH‐responsive polyzwitterions: A comparative study of acrylamide‐based polyampholyte terpolymers and polybetaine copolymers

A comparative study of pH‐responsive polyzwitterions (PZs) with polyampholyte or polybetaine architectures was conducted with well‐defined model polymer systems. Low‐charge‐density PZs, including ampholytic terpolymers composed of acrylamide (AM), sodium 3‐acrylamido‐3‐methylbutanoate, and (3‐acrylamidopropyl)trimethylammonium chloride and carboxybetaine copolymers composed of AM and 3‐(3‐acrylamidopropyldimethylammonio)propionate, were prepared via free‐radical polymerization in 0.5M NaCl to yield ter‐ and copolymers with random termonomer and comonomer distributions. Sodium formate was used as a chain‐transfer agent during the polymerizations to eliminate the effects of the monomer feed composition on the degree of polymerization (DP) and to suppress gel effects and broadening of the molecular weight distributions. The polymer compositions were determined via ¹³C‐NMR spectroscopy, and the residual counterion content was determined via elemental analysis for Na⁺ and Cl^?. The molecular weights (MWs) and polydispersity indices (PDIs) were determined via size exclusion chromatography/multi‐angle laser light scattering (SEC–MALLS); the polymer MWs ranged from 1.4 to 1.5 × 10⁶ g/mol, corresponding to DPs of 1.6–1.9 × 10⁴ repeat units, with all the polymers exhibiting PDIs less than or equal to 2.1. The intrinsic viscosities determined from SEC–MALLS data and the Flory–Fox relationship agreed with the intrinsic viscosities determined via low‐shear dilute‐solution viscometry. Data from the SEC–MALLS analysis were used to analyze the radius of gyration/molecular weight (R_g–M) relationships and the Mark–Houwink–Sakurada intrinsic viscosity/molecular weight ([η]–M) relationships for the PZs. The R_g–M and [η]–M relationships and viscometric data revealed that under size exclusion chromatography conditions, the poly[acrylamide‐co‐3‐(3‐acrylamidopropyldimethylammonio)propionate] betaine copolymers had more open, random‐coil conformations and greater polymer–solvent interactions than the ampholytic poly[acrylamide‐co‐sodium 3‐acrylamido‐3‐methylbutanoate‐co‐(3‐acrylamidopropyl)trimethylammonium chloride] terpolymers. The pH‐ and salt‐responsive dilute‐solution viscosity behavior of the PZs was examined to assess the effects of the polymer structure and composition on the solution properties. The polyampholyte terpolymers had greater solution viscosities and more pronounced stimuli‐responsiveness than the polybetaine copolymers because of their stronger intramolecular interactions and increased chain stiffness. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 24–39, 2004     

Effects of poly(vinyl acetate) and poly(vinyl chloride‐co‐vinyl acetate) low‐profile additives on properties of cured unsaturated polyester resins. II. glass‐transition temperatures and mechanical properties

Three series of self‐synthesized poly(vinyl acetate)‐based low‐profile additives (LPAs), including poly(vinyl acetate), poly(vinyl chloride‐co‐vinyl acetate), and poly(vinyl chloride‐co‐vinyl acetate‐co‐maleic anhydride), with different chemical structures and molecular weights were studied. Their effects on the glass‐transition temperatures and mechanical properties for thermoset polymer blends made from styrene, unsaturated polyester, and LPAs were investigated by an integrated approach of the static phase characteristics, cured sample morphology, reaction kinetics, and property measurements. Based on Takayanagi mechanical models, the factors that control the glass‐transition temperature in each phase region of the cured samples and the mechanical properties are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3347–3357, 2003     

Determination of molecular weight for poly(vinyl butyral) using size exclusion chromatography/low-angle laser light scattering (SEC/LALLS) in hexafluoroisopropanol

Size exclusion chromatography/low-angle laser light-scattering (SEC/LALLS) determinations of molecular weight for poly(vinyl butyral) (PVB) using hexafluoroisopropanol (HFIP) as the polymer solvent and chromatographic mobile phase are described. The use of HFIP provided aggregate-free SEC/LALLS chromatograms from which molecular weight distribution averages were calculated. Comparison of SEC/LALLS molecular weights determined in HFIP with similar data obtained using tetrahydrofuran as the polymer solvent and chromatographic mobile phase indicated that the former is more generally applicable for PVB of different vinyl alcohol content.     

Preparation and characterization of ceria nanoparticles supported on poly(4‐vinyl pyridine‐co‐divinyl benzene)

Formation of ceria nanoparticles in 2% divinyl benzene (dvb) crosslinked 4‐vinyl pyridine (4vp) polymer [poly(4vp‐co‐dvb)] microspheres was investigated. The polymer was prepared by free radical suspension polymerization method. Poly(4vp‐co‐dvb)/ceria nanocomposites were prepared by reacting CeCl₃·7H₂O and NaOH in the presence of poly(4vp‐co‐dvb) at room temperature in aqueous media. The mole ratio of the metal to polymer was varied from 2.5 to 10% with an increment of 2.5. The polymer and nanocomposities were characterized by various spectrochemical methods. The coordination of nitrogen atoms of the polymer with Ce(IV) of ceria (CeO₂) has been confirmed from X‐ray photoelectron spectroscopy (XPS). The method has yielded ceria nanoparticles in an average size of 15 nm according to transmission electron microscopy. Differential scanning calorimetry, thermogravimetric analysis, X‐ray diffractometry and XPS analysis with respect to mole percentage of ceria in the composite are discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3439–3445, 2006     

Preparation of electrorheological active ionomers from poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine)

In this study, synthesis, characterization, partial hydrolysis, and salt formation of poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine), (poly(HEMA)‐co‐poly‐(4‐VP)) copolymers were investigated. The copolymers were synthesized by free radical polymerization using K₂S₂O₈ as an initiator. By varying the monomer/initiator ratio, chain lengths of the copolymers were changed. The copolymers were characterized by gel permeation chromatography (GPC), viscosity measurements, ¹H and ¹³C NMR and FTIR spectroscopies, elemental analysis, and end group analysis methods. The copolymers were partially hydrolyzed by p‐toluene sulfonic acid monohydrate (PTSA·H₂O) and washed with LiOH_(aq) solution to prepare electrorheological (ER) active ionomers, poly(Li‐HEMA)‐co‐poly(4‐VP). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3540–3548, 2006     

Understanding the mechanical and biodegradation behaviour of poly(hydroxybutyrate)/rubber blends in relation to their morphology

In this work poly(hydroxybutyrate/poly(vinyl butyral)‐ co‐(vinyl alcohol)‐co(vinyl acetate) (or ethylene propylene diene monomer rubber) blends were prepared by conventional processing techniques (extrusion and injection moulding). A droplet type morphology was obtained for P(3HB)/PVB blends whereas P(3HB)/EPDM blends presented some extent of co‐continuous morphology. In addition, rubbery domains were much smaller in the case of PVB. These differences in morphology are discussed taking into account solubility parameters and rheological behaviours of each component. For both blends, the increase of elastomer ratio led to a decrease of Young's modulus but an increase in elongation at break and impact strength. The latter increased more in the case of P(3HB)/EPDM blends although the rubbery domains were larger. These results are explained in the light of the glass transition of the rubber and the presence of plasticizer in the case of PVB. The addition of elastomer also resulted in an increase of P(3HB) biodegradation rate, especially in the case of EPDM. It is assumed that, in this case, the size and morphology of the rubbery domains induce a geometrical modification of the ‘erosion front’ which leads to an increase of the interface between P(3HB) phase and the degradation medium and consequently to an apparently faster biodegradation kinetics of PHB/rubber blends. Copyright © 2011 Society of Chemical Industry     

Polymer nanocomposites containing carbon nanotubes and miscible polymer blends based on poly[ethylene‐co‐(acrylic acid)]

Four binary polymer blends containing poly [ethylene‐co‐(acrylic acid)] (PEAA) as one component, and poly(4‐vinyl phenol‐co‐2‐hydroxy ethyl methacrylate) (P4VPh‐co‐2HEMA) or poly(2‐ethyl‐2‐oxazoline) (PEOx) or poly(vinyl acetate‐co‐vinyl alcohol) (PVAc‐co‐VA) or poly (vinylpyrrolidone‐co‐vinyl acetate) (PVP‐co‐VAc) as the other component were prepared and used as a matrix of a series of composite materials. These binary mixtures were either partially or completely miscible within the composition range studied and were characterized by differential scanning calorimetry (DSC) and Fourier transformed infrared spectroscopy (FTIR). Carbon nanotubes (CNTs) were prepared by a thermal treatment of polyester synthesized through the chemical reaction between ethylene glycol and citric acid over an alumina boat. High resolution transmission electron microscopy (HRTEM) was used to characterize the synthesized CNTs. Films of composite materials containing CNTs were obtained after evaporation of the solvent used to prepare solutions of the four types of binary polymer blends. Young's moduli of the composites were obtained by thermomechanical analysis at room temperature. Only one glass transition temperature was detected for several compositions on both binary blends and the composite material matrices. Evidence of hydrogen bond formation was recorded for both miscible blends and composite materials. The degree of crystallinity and Young's moduli of the CNT‐polymer composites increased compared to the single polymer blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis and antitumor activity of poly(3,4‐dihydro‐2H‐pyran‐co‐maleic anhydride‐co‐vinyl acetate)

The radical‐initiated terpolymerization of 3,4‐dihydro‐2H‐pyran (DHP), maleic anhydride (MA), and vinyl acetate (VA), which were used as a donor–acceptor–donor system, was carried out in methyl ethyl ketone in the presence of 2,2′‐azobisisobutyronitrile as an initiator at 65°C in a nitrogen atmosphere. The synthesis and characterization of binary and ternary copolymers, some kinetic parameters of terpolymerization, the terpolymer‐composition/thermal‐behavior relationship, and the antitumor activity of the synthesized polymers were examined. The polymerization of the DHP–MA–VA monomer system predominantly proceeded by the alternating terpolymerization mechanism. The in vitro cytotoxicities of poly(3,4‐dihydro‐2H‐pyran‐alt‐maleic anhydride) [poly(DHP‐alt‐MA)] and poly(3,4‐dihydro‐2H‐pyran‐co‐maleic anhydride‐co‐vinyl acetate) [poly(DHP‐co‐MA‐co‐VA)] were evaluated with Raji cells (human Burkitt lymphoma cell line). The antitumor activity of the prepared anion‐active poly(DHP‐alt‐MA) and poly(DHP‐co‐MA‐co‐VA) polymers were studied with methyl–thiazol–tetrazolium testing, and the 50% cytotoxic dose was calculated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2352–2359, 2005     

Synthesis and biological activity of medium molecular weight polymers containing 3,6‐endo‐methylene‐1,2,3,6‐tetrahydrophthalimidobutanoyl‐5‐fluorouracil

A new monomer, 3,6‐endo‐methylene‐1,2,3,6‐tetrahydrophthalimidobutanoyl‐5‐fluorouracil (ETBFU), was synthesized by reaction of 3,6‐endo‐methylene‐1,2,3,6‐tetrahydrophthalimidobutanoyl chloride and 5‐fluorouracil. The homopolymer of ETBFU and its copolymers with acrylic acid (AA) or vinyl acetate (VAc) were prepared by photopolymerization using 2,2‐dimethoxy‐2‐phenylacetophenone as an initiator at 25 °C. The synthesized ETBFU and its polymers were identified by FTIR, ¹H NMR and ¹³C NMR spectroscopies. The ETBFU content in poly(ETBFU‐co‐AA) and poly(ETBFU‐co‐VAc) was 43 and 14 mol%, respectively. The apparent number‐average molecular weight (M_n) of the polymers determined by GPC ranged from 8400 to 11 300. The in vitro cytotoxicity of the samples against mouse mammary carcinoma (FM3A), mouse leukaemia (P388), and human histiocytic lymphoma (U937) cancer cell lines decreased in the order 5‐FU ≥ ETBFU > poly(ETBFU) > poly(ETBFU‐co‐AA) > poly(ETBFU‐co‐VAc). The in vivo antitumour activity of the polymers against Balb/C mice bearing sarcoma 180 tumour cells was greater than that of 5‐fluorouracil at all doses tested. © 2000 Society of Chemical Industry     

Effect of compatibility of cellulose acetate/poly(vinyl butyral) blends on pervaporation behavior of their membranes for methanol/methyl tert‐butyl ether mixture

Binary blends and their blend membranes of cellulose acetate (CA) and poly(vinyl butyral) (PVB) are prepared by solution blending. The compatibility of the blends is studied by viscometry and Fourier transform IR. It is found that the incompatibility of the blends is markedly manifested when the weight fraction of PVB in the CA/PVB blends (W_PVB) is located at higher regions. On the other hand, compatibility is obtained for the CA/PVB blends with lower W_PVB values, especially at about 0.2. This compatibility is believed to play a key role in the good pervaporation behavior of CA/PVB blend membranes. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2434–2439, 2002     

Production and characterization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) co‐polymer by a N2‐fixing cyanobacterium,Nostoc muscorum Agardh

BACKGROUND: Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(3HB‐co‐3HV)] co‐polymer has immense potential in the field of environmental and biomedical sciences as biodegradable and biocompatible material. The present study examines a filamentous N₂‐fixing cyanobacterium, Nostoc muscorum Agardh as a potent feedstock for P(3HB‐co‐3HV) co‐polymer production and characterization of co‐polymer film for commercial applications. RESULTS: Under photoautotrophic growth conditions, N. muscorum Agardh accumulated the homopolymer of poly‐β‐hydroxybutyrate (PHB), whereas synthesis of P(3HB‐co‐3HV) co‐polymer was detected under propionate‐ and valerate‐supplemented conditions. Exogenous carbons such as acetate, fructose and glucose supplementation with propionate/valerate was found highly stimulatory for the co‐polymer accumulation; the content reached 58–60% of dry cell weight (dcw) under P‐/N‐deficiencies with 0.4% acetate + 0.4% valerate supplementation, the highest value reported so far for P(3HB‐co‐3HV) co‐polymer‐producing cyanobacterial species. The material properties of the films were studied by mechanical tests, surface analysis and differential scanning calorimetry (DSC). CONCLUSION: N. muscorum Agardh, a photoautotrophic N₂‐fixing cyanobacterium, emerged as a potent host for production of P(3HB‐co‐3HV) co‐polymer with polymer content 60% of dry cell weight. The material properties of the films were found to be comparable with that of the commercial polymer, thus advocating its potential applications in various fields. Copyright © 2012 Society of Chemical Industry     

Blends of poly(vinyl butyral‐co‐vinyl alcohol) and poly(ethylene terephthalate‐co‐ethylene naphthalate): thermal,mechanical, and morphological properties

The miscibility behavior and morphology of a series of poly(vinyl butyral‐co‐vinyl alcohol) (PVBA) copolymers containing 29, 52, 76, and 88 mol % of vinyl alcohol units with poly(ethylene terephthalate‐co‐ethylene naphthalate) (PETN) was investigated by DSC and SEM. Blends of the PETN with PVBA were prepared by coprecipitation from a chloroform/o‐chlorophenol (20/80 wt %) mixture solvent. It was found that PVBAs with different vinyl alcohol content will form an immiscible phase with the amorphous PETN in the solution‐cast films. Also, PETN and PVBA with 29 mol % vinyl alcohol (PVBA‐29) are not miscible within the whole composition range. The glass‐transition temperatures of the blends were higher than those of the two‐component polymers. The values of the tensile properties of the blend films were also better than those of the original copolymer films. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2746–2751, 2001     

Synthesis and biological activity of phthalimide‐based polymers containing 5‐fluorouracil

The attachment of anticancer agents to polymers is a promising approach towards reducing the toxic side‐effects and retaining the potent antitumour activity of these agents. A new tetrahydrophthalimido monomer containing 5‐fluorouracil (ETPFU) and its homopolymer and copolymers with acrylic acid (AA) and with vinyl acetate (VAc) have been synthesized and spectroscopically characterized. The ETPFU contents in poly(ETPFU‐co‐AA) and poly(ETPFU‐co‐VAc) obtained by elemental analysis were 21 mol% and 20 mol%, respectively. The average molecular weights of the polymers determined by gel permeation chromatography were as follows: M_n = 8900 g mol^?1, M_w = 13 300 g mol^?1, M_w/M_n = 1.5 for poly(ETPFU); M_n = 13 500 g mol^?1, M_w = 16 600 g mol^?1, M_w/M_n = 1.2 for poly(ETPFU‐co‐AA); M_n = 8300 g mol^?1, M_w = 11 600 g mol^?1, M_w/M_n = 1.4 poly(ETPFU‐co‐VAc). The in vitro cytotoxicity of the compounds against FM3A and U937 cancer cell lines increased in the following order: ETPFU > 5‐FU > poly(ETPFU) > poly(ETPFU‐co‐AA) > poly(ETPFU‐co‐VAc). The in vivo antitumour activities of all the polymers in Balb/C mice bearing the sarcoma 180 tumour cell line were greater than those of 5‐FU and monomer at the highest dose (800 mg kg^?1). © 2002 Society of Chemical Industry