Low‐temperature thermal graft copolymerization of 1‐vinyl imidazole on fluorinated polyimide films with simultaneous lamination of copper foils

A simple technique of thermal graft copolymerization of 1‐vinyl imidazole (VIDZ) on pristine and argon plasma pretreated fluorinated polyimide (FPI) films with simultaneous lamination of copper foils was demonstrated. The simultaneous thermal grafting and lamination process was carried out in the temperature range of 80–140°C under atmospheric conditions and in the complete absence of a polymerization initiator. Three different FPI samples of different chemical structures were employed in the present study. An optimum T‐peel strength about 15 N/cm was achieved for the copper/FPI laminate. The adhesion strength, however, decreased with increasing fluorine content in the FPI film. The onset of cohesive failure occurred in the FPI film for assemblies with T‐peel strength greater than 6 N/cm. The T‐peel strengths are reported as a function of the argon plasma pretreatment time of the FPI films and thermal lamination temperature. The adhesion strengths were compared to that of the similarly prepared copper/polyimide (Kapton HN) laminate. Time‐dependent water contact angle (Θ) measurements indicated that the surfaces of FPI films are significantly more hydrophobic and more resistant to water diffusion or hydration than the Kapton HN films. The surface compositions of the pristine FPI films, as well as the delaminated FPI films and copper foils were studied by X‐ray photoelectron spectroscopy. The thickness of the graft VIDZ polymer layer was in the order of 200 nm, as derived from the cross‐sectional view of the scanning electron micrograph. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1478–1489, 1999     

Electroless plating of copper on polyimide films modified by surface grafting of tertiary and quaternary amines polymers

Argon plasma-pretreated polyimide (PI, Kapton^® HN) films were subjected to UV-induced surface graft copolymerization with N,N′-(dimethylamino)ethyl methacrylate (DMAEMA) and 2-(trimethylammonium)ethyl methacrylate chloride (TMMAC). The DMAEMA graft-copolymerized PI (DMAEMA-g-PI) surfaces were also quaternized and amino-functionalized with 3-bromopropylamine hydrobromide (the Q-DMAEMA-g-PI surfaces). The surface composition and the degree of quaternization of the graft-modified PI films were determined by X-ray photoelectron spectroscopy. The DMAEMA-g-PI, Q-DMAEMA-g-PI and TMMAC graft-copolymerized PI (TMMAC-g-PI) surfaces can be activated directly by PdCl₂, in the absence of prior sensitization by SnCl₂ (the ‘Sn-free’ activation process), for the subsequent electroless plating of copper. A shorter induction time for the electroless deposition of copper was found for the palladium-activated Q-DMAEMA-g-PI and TMMAC-g-PI surfaces than for the palladium-activated DMAEMA-g-PI surface. The T-peel adhesion strength of the electrolessly deposited copper with the Q-DMAEMA-g-PI surface was enhanced to above 6 N/cm, in comparison to only about 4 N/cm for the DMAEMA-g-PI surface, about 2.5 N/cm for the TMMAC-g-PI surface, or about 0.5 N/cm for the PI surface with argon plasma treatment alone.     

Studies on graft copolymerization of 4‐vinylpyridine onto guar gum

Graft copolymerization of 4‐vinylpyridine (4‐VP) onto guar gum (GOH) using potassium monopersulfate (PMS)/thioacetamide (TAA) as a redox pair was studied in an aqueous medium under inert atmosphere. The concentration of potassium monopersulfate and thioacetamide should be 1.0 × 10^?2 and 5.0 × 10^?3 mol dm^?3, respectively, for highest grafting ratio and efficiency. Efficient grafting was observed at 19.25 × 10^?2 and 4.87 × 10^?2 mol dm^?3 concentration of 4‐vinylpyridine and sulfuric acid, respectively. The optimum temperature for grafting is 30°C. As the time period of reaction is increased, the grafting ratio increases, whereas efficiency decreases. The plausible mechanism of grafting has been suggested. A sample of guar gum and guar‐ g‐4‐vinylpyridine were subjected to thermogravimetric analysis with the objective of studying the effect of grafting 4‐vinylpyridine on the thermal stability of guar gum. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2380–2385, 2002     

聚酰亚胺薄膜表面无钯活化化学镀铜

为了增加聚酰亚胺薄膜表面与化学镀铜层的结合力,采用NaOH溶液对其表面进行化学改性,然后在其表面制备出具有催化活性的银微粒,进而化学镀铜。使用傅里叶变换衰减全反射红外光谱仪(FTIR-ATR)和能谱分析仪(EDS)对聚酰亚胺的表面结构和组成进行了表征和分析,利用X射线衍射(XRD)及扫描电子显微镜(SEM)表征铜镀层的结构及表面微观形貌。结果表明,聚酰亚胺表面在NaOH溶液中发生水解,在AgNO3溶液中实现Ag+与Na+间的离子交换,Ag+通过化学吸附附着在聚酰亚胺表面。在镀铜液中,Ag+先被甲醛还原成银微粒,从而引发化学镀铜反应的发生,并可获得结合力良好的化学镀铜层。     

Study of modified polypropylene nonwoven cloth. I. graft copolymerization of 4‐vinylpyridine onto polypropylene nonwoven cloth by preirradiation method

Polypropylene (PP) nonwoven cloth was grafted with 4‐vinylpyridine (4‐VP) by a preirradiation method. The effects of preirradiation conditions on the mechanical properties of preirradiated PP nonwoven cloth and the percentage of grafting (Pg) of 4‐VP onto the preirradiated PP nonwoven cloth were systematically investigated. The results indicated that the mechanical properties of preirradiated PP nonwoven cloth decreased with increasing irradiation dose and that the Pg was greatly affected by the concentration of monomer, irradiation dose, grafting reaction temperature, and the addition of inhibitor and inorganic acid in the grafting reaction system. The grafted nonwoven cloth samples were characterized using IR spectroscopy and SEM. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1861–1868, 2000     

Electroless silver plating on the PET fabrics modified with 3‐mercaptopropyltriethoxysilane

The feasibility of adherent silver layers onto PET fabrics by electroless plating was explored and its optimal technology for modification and electroless plating was investigated. Morphology, structure, and thermal stability of silver plating PET fabrics were characterized by scanning electric microscope (SEM), X‐ray diffraction (XRD) and thermogravitric (TG) analysis. As the silver weight on the modified fabric is 25 g/m², the electromagnetic shielding effectiveness (SE) of silver plating PET fabric is more than 30dB at the frequency ranging from 1MHz to 5000 MHz. The results show that the silver plating PET fabric has good electrical conductivity and electromagnetic shielding property. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Radiation‐induced graft copolymerization of 2‐vinylpyridine and styrene onto isotactic polypropylene fiber

Isotactic polypropylene fiber (IPP) was graft‐copolymerized using 2‐vinyl pyridine (2‐VP) and styrene (sty) as the monomers by the mutual irradiation method in air. The percentage of grafting was determined as a function of various reaction parameters and it was found that the maximum grafting of 2‐VP (114%) and sty (76%) was obtained at an optimum dose of 1.08 × 10⁴ and 0.64 × 10⁴ Gy using 1.8 × 10⁻² mol of 2‐VP and 4.3 × 10⁻² mol of sty, respectively. The graft copolymers were characterized by differential scanning calorimetric analysis and isolation of the grafted chains from the grafted iPP samples. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2959–2969, 1999     

Thermal graft copolymerization of 4-vinyl pyridine on polyimide to improve adhesion to copper

The surface of poly[N,N′-(oxydiphenylene)pyromellitimide] film, Kapton^® HN, was modified to improve its adhesion to copper metal. The polyimide surface was argon plasma activated and then exposed to air. A nitrogen-containing monomer, 4-vinyl pyridine, was then polymerized at elevated temperature under constant pressure between the argon plasma activated polyimide film and copper foil without any added photoinitiator. Optimization of the argon pretreatment time, curing temperature and curing duration resulted in almost doubling of the single lap shear strength. It is postulated that failure occurred mainly between the polyimide and the poly(4-vinyl pyridine).     

Nitroxide‐mediated homopolymerization and copolymerization of 2‐vinylpyridine with styrene

Homopolymerization and copolymerization of 2‐vinylpyridine (2VP) with styrene (S) at 125°C in the presence of 2,2,6,6‐tetramethyl piperidin‐1‐yloxyl (TEMPO) radicals have been studied. The homopolymerization was carried out with 2,2′‐azobis(isobutyronitrile) (AIBN) as a thermal initiator or without AIBN in the initial reaction mixture. In the copolymerization initiated with AIBN, the molar fraction of 2VP in the feed, F_2VP, varied in the range of 0.1–0.9; F_2VP = 0.65 was found to be the azeotropic composition. The linear semilogarithmic time–conversion plots demonstrated a pseudoliving nature of the polymerizations under study. The molecular weight–conversion dependences indicated the participation of side reactions, diminishing the number of TEMPO‐terminated polymer chains. The synthesized homopolymers and copolymers were characterized using size‐exclusion chromatography (SEC), nitrogen analysis, and NMR spectroscopy. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2024–2030, 2001     

Electroless plating of moisture‐curable polyurethane undercoating films

The compatibility of using moisture‐curable polyurethane (MCPU) system as a thin undercoating layer with electroless plating process was evaluated. The characteristics of the MCPU before and after chemical etching treatment were analyzed using atomic force microscope (AFM), scanning electrode microscope (SEM), contact‐angle measurements, and (Fourier‐Transform Infrared) FTIR spectroscopy. We found that surface morphology and roughness of the MCPU is affected by curing period and etching times. A proper combination of curing period and etching times are critical for obtaining a fully metallized surface. All MCPU samples that were etched for 15 min show poor plating performance due to surface damage caused by mild etching treatment. A standard pull‐off testing method (ASTM 4541) was used to evaluate the adhesion strength of nickel–MCPU. Only samples that were postcured for 4 days show influence of surface roughness on adhesion strength. On average, samples that were postcured for 7 days before electroless plating showed better adhesion of nickel–MCPU compared with samples that were postcured for 2 or 4 days. The results show that MCPU system can be used as a thin undercoating layer for electroless plating. It also offers smooth metal–polymer interface and therefore has the potential to be exploited for use in many electroless plating applications including in the decorative such as ornaments and display items and also in electronic industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1554–1565, 2007     

Radiation‐induced graft copolymerization of α‐methyl styrene and butyl acrylate mixture into polyetheretherketone films

Radiation‐induced graft copolymerization of α‐methyl styrene (AMS), butyl acrylate (BA) monomers, and their mixture was investigated on poly(etheretherketone) films. The graft polymerization was carried out using ethyl methyl ketone as the medium for the copolymerization and the maximum degree of grafting of 27% was achieved. It was observed that the grafting is significantly influenced by the reaction conditions, such as reaction time, preirrradiation dose, monomer concentration, monomer ratio, and the reaction temperature. The degree of grafting increases as the monomer concentration increases up to 30%, beyond which a decrease in the grafting was observed. The degree of grafting showed a maximum at 40% BA content in the monomer mixture. The temperature dependence of the grafting process shows decreasing grafting with the increase in the reaction temperature. The presence of AMS and BA grafts in the film was confirmed by FTIR spectra. The relative change in the PBA/PAMS fraction with respect to the reaction temperature has been found in this study. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Surface modification of plasma‐pretreated high density polyethylene films by graft copolymerization for adhesion improvement with evaporated copper

Surface modification of Ar plasma‐pretreated high density polyethylene (HDPE) film via UV‐induced graft copolymerization with glycidyl methacrylate (GMA) and 2‐hydroxyethylacrylate (HEA) was carried out to improve the adhesion with evaporated copper. The surface compositions of the modified HDPE surfaces were characterized by X‐ray photoelectron spectroscopy (XPS). The adhesion strengths of evaporated copper with the graft‐copolymerized HDPE films were affected by the Ar plasma pretreatment time, the monomer concentration used for graft copolymerization, and the graft concentration. Post‐treatments, such as plasma post‐treatments after graft copolymerization and thermal treatment (curing) after metalization, further enhanced the adhesion strength of the Cu/HDPE laminates. The T‐type peel strengths of the laminates involving the graft‐modified and plasma posttreated HDPE films were greater than 15 N/cm. The enhanced adhesion strength resulted from the strong affinity of the graft chains for Cu and the fact that the graft chains were covalently tethered on the HDPE surface. XPS characterization of the delaminated surfaces of the Cu/HDPE laminates revealed that the failure mode of the laminates with T‐peel adhesion strengths greater than 5 N/cm was cohesive in nature.     

Surface modification of polythiophene and poly(3‐methyl thiophene) films by graft copolymerization

Polythiophene (PTH) and poly(3‐methyl thiophene) (PMT) films were electrochemically polymerized in an electrolyte solution of boron fluoride–ethyl ether. Ozone‐pretreated PTH and PMT films were subjected to UV‐light‐induced graft copolymerization with different monomers, including poly(ethylene glycol) monomethacrylate, acrylic acid, and glycidyl methacrylate. Surface grafting with the hydrophilic polymers gave rise to more hydrophilic PTH and PMT films. The structure and chemical composition of each copolymer surface were studied by X‐ray photoelectron spectroscopy. The surface grafting with the hydrophilic polymers resulted in a more hydrophilic PTH film. The dependence of the density of surface grafting and the conductivities of the grafted PTH and PMT films on the ozone pretreatment was also studied. A large amount of the grafted groups at the surface of the PTH and PMT films remained free for further surface modification and functionalization. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Low-temperature graft copolymerization of 1-vinyl imidazole on low-density polyethylene films with simultaneous lamination of copper foils

Surface modification of argon plasma-pretreated low-density polyethylene (LDPE) films by graft copolymerization with 1-vinyl imidazole (VIDz) and with concurrent lamination of copper foils at room temperature and at an elevated temperature were carried out. The adhesion strengths were reported as lap shear adhesion strengths and T-peel strengths. The surfaces of the graft copolymerized films and the mechanically delaminated LDPE and Cu surfaces were characterized by X-ray photoelectron spectroscopy (XPS). It was found that plasma pretreatment of LDPE alone, and in the absence of VIDz, could give rise to strong lap shear adhesion between the polymer and copper. Significant T-peel strengths, however, were obtained only for LDPE/Cu laminates obtained from the simultaneous graft copolymerization and lamination technique. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1977–1983, 1998     

Surface characterization and study of Langmuir films of poly(4‐vinylpyridine) quaternized with n‐alkylbromide

The surface behaviour of poly(4‐vinylpyridine)s (P4VP) quaternized with four different alkyl chains (pentyl, hexyl, octyl and decy bromide) were studied. Surface pressure–area isotherms (π–A) at the air–water interface were determined. Depending on the length of the side‐chains, the π–A isotherms show a plateau region. An extensive plateau is observed for n > 6. The plateau pressures are similar for n = 8 and n = 10. The monolayers are stable and exhibit hysteresis phenomena. Brewster angle microscopy (BAM) is used to monitor the monolayer topography of the polymer on water subphase. To obtain information about the surface energy (SE) and the degree of hydrophobicity of these systems, we have estimated the critical surface tension, γ_c, and the dispersion force and polar contributions to SE, γ_D and γ_P, respectively, by measurements of the contact angle (CA) of water and bromobenzene on the polymer surface. The results obtained are depend on the length of the alkyl lateral chain of the functionalized polymers. © 2001 Society of Chemical Industry     

Properties and thermal degradation study of blend films with poly(4‐vinylpyridine) and lignin

A series of blend films with different ratio of poly(4‐vinylpyridine) (PVP) to lignin were subjected to dynamic DSC and TGA measurement under nitrogen atmosphere at various heating rates. DSC curves showed that the glass transition temperatures of these blends decreased with the increase of lignin content. TGA studies indicated that the lignin content produced obvious effect on the thermal stability of these blends. The kinetic model function of the thermal decomposition of these blends obeyed the Avrami‐Erofeev model equation, g(α) = [‐ln(1‐α)]^1/m. The degradation kinetic parameters were also obtained. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1875–1879, 2005     

Surface modification of low‐density polyethylene films by UV‐induced graft copolymerization with a fluorescent monomer

Surface modification of argon plasma–pretreated low‐density polyethylene (LDPE) film via UV‐induced graft copolymerization with a fluorescent monomer, (pyrenyl)methyl methacrylate (Py)MMA, was carried out. The chemical composition and morphology of the (Py)MMA‐graft‐copolymerized LDPE [(Py)MMA‐g‐LDPE] surfaces were characterized, respectively, by X‐ray photoelectron spectroscopy (XPS) and by atomic force microscopy (AFM). The concentration of the surface‐grafted (Py)MMA polymer increased with Ar plasma pretreatment time and UV graft copolymerization time. The photophysical properties of the (Py)MMA‐g‐LDPE surfaces were measured by fluorescence spectroscopy. After graft copolymerization with the fluorescent monomer, the surface of the LDPE film was found to have incorporated new and unique functionalities. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1526–1534, 2001     

Synthesis of poly(styrene‐co‐4‐vinylpyridine) microspheres via dispersion polymerization: Effect of the concentration of 4‐vinylpyridine

Amphiphilic copolymer microspheres of poly(styrene‐co‐4‐vinylpyridine) were prepared by dispersion polymerization in an alcohol/water medium. The synthesis of poly(styrene‐co‐4‐vinylpyridine) microparticles was successfully carried out, and the latexes had a spherical morphology with good monodispersity. The degree of conversion in the early stage of polymerization decreased with increasing 4‐vinylpyridine (4VP) monomer content, but the final conversions were similar (>95%). The copolymerization rate decreased with increasing 4VP content, and a broad particle size distribution was observed with 20 wt % 4VP because of the prolonged nucleation time. With the 4VP concentration increasing, the molecular weight of the copolymer microspheres decreased, and the glass‐transition temperature of the copolymers increased; this indicated that all the copolymers were random and homogeneous. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Copolymerization of methyl methacrylate with 4‐vinylpyridine initiated by a novel Ni(II)α‐Benzoinoxime complex

Copolymerizations of methyl methacrylate (MMA) with 4‐vinylpyridine (4VP) were performed from different monomer feed ratios in 1,4‐dioxan at 30°C under free radical initiation experimental conditions, using Ni(II)α‐Benzoinoxime complex as initiator. The obtained copolymers (PMMA4VP) were examined by FTIR and ¹H NMR spectroscopies. The composition of these copolymers was calculated, using ¹H NMR spectra and elemental analysis. Monomer reactivity ratios were estimated from Fineman–Ross (FR, r_m = 0.550, r_v = 1.165) and Kelen–Tudos (KT, r_m = 0.559, r_v = 1.286) linearization methods, as well as nonlinear error in variables model (EVM) method using the RREVM computer program (RREVM, r_m = 0.559, r_v = 1.264). These values suggest that MMA‐4VP pair copolymerizes randomly. ¹H NMR spectra provide information about the stereochemistry of the copolymers in terms of sequence distributions and configurations. These results showed that the age of the Ni complex has an impact not only on its activity towards polymerization reactions but also on the features of the corresponding copolymers, whereas the chemical composition was insensitive to this prominent factor. The mechanism of MMA‐4VP copolymerization is consistent with a radical process as supported by microstructure and molecular weight distribution studies. Thermal behaviours of these copolymers were investigated by differential scanning calorimetry and thermogravimetric analysis. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Synthesis and characterization of polyethylene modified through phase‐transfer‐catalyzed graft copolymerization

In an effort to impart biodegradability, polyethylene (PE) was modified through the graft copolymerization of vinyl monomers such as acrylamide (AAm) and acrylic acid (AAc) by a phase‐transfer‐catalyst method. The grafting percentage of AAm and AAc for PE was found to be dependent on the dibenzoyl peroxide concentration, monomer concentration, time, temperature, and concentration of the phase‐transfer catalyst. Some AAm‐ and AAc‐grafted PE samples were prepared by chemical, UV, and γ‐radiation methods. The biodegradation of samples of PE, polyethylene‐g‐polyacrylamide, and polyethylene‐g‐poly(acrylic acid) prepared by all these methods was studied. The weight loss of the samples over a period of time was observed with soil‐burial tests. The grafted samples prepared by the phase‐transfer‐catalyst method showed better biodegradation results than those prepared by other methods of grafting. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008