Effect of molecular structure on extrudate swell behavior for different thermoplastic melts in an electro‐magnetized die

The extrudate swell ratio of five different thermoplastic melts flowing in a constant shear rate rheometer having a capillary die with and without application of magnetic field was studied. The effects of the magnetic flux direction and density, die temperature, and wall shear rate on the extrudate swell and flow properties were investigated. The experimental results suggested that an increasing wall shear rate increased the swelling ratio for the polystyrene (PS), LLDPE, and PVC melts, but the opposite effect was observed for the ABS and PC melts. The extrudate swell ratio for the PS, ABS, PC, and LLDPE melts decreased with increasing die temperature, the effect being reversed for the PVC melt. Thermoplastic melts having high benzene content in the side‐chain and exhibiting anisotropic character were apparently affected by the magnetic field, the extrudate swell ratio increasing with magnetic flux density. The effect of the magnetic field on the extrudate swell ratio decreased in the order of PS → ABS → PC. The extrudate swell ratio for the co‐parallel magnetic field system was slightly higher than that for the counter‐parallel magnetic field system at a high magnetic flux density. POLYM. ENG. SCI., 47:270–280, 2007. © 2007 Society of Plastics Engineers.     

Experimental study on extrudate swell and die geometry of profile extrusion

The objective of this study was to determine the die swell behavior of a polymer melt and to design a die for forming a polymeric extrudate with a desired shape using profile extrusion. Polystyrene pellets were chosen to perform the profile extrusion experiments. First, the polystyrene pellets were melted and pushed through a quarter ring profile. The profile of the swelled extrudate agreed with the numerical predictions. A modified die was designed to produce a quarter ring profile extrudate based on the direct extrusion problem (DEP) prediction. Polystyrene pellets were also melted and pushed through the modified die. The experimental results were close to the computational results. The melting temperature, die length, and melting residence time affect die swell behavior. The die swell ratio becomes smaller as the melting temperature and melting residence time are increased. As the die length is increased, the die swell ratio is lowered. According to the die geometry predictions, an extrudate with the desired profile can be made precisely.     

A parallel coextrusion technique for simultaneous measurements of radial die swell and velocity profiles of a polymer melt in a capillary rheometer

This article proposes a new experimental technique to simultaneously measure radial die swell and velocity profiles of polystyrene melt flowing in the capillary die of a constant shear rate rheometer. The proposed technique was based on parallel coextrusion of colored melt‐layers into uncolored melt‐stream from the barrel into and out of the capillary die. The size (thickness) ratio of the generated melt layers flowing in and out of the die was monitored to produce the extrudate swell ratio for any given radial position across the die diameter. The radial velocity profiles of the melt were measured by introducing relatively light and small particles into the melt layers, and the times taken for the particles to travel for a given distance were measured. The proposed experimental technique was found to be both very simple and useful for the simultaneous and accurate measurement of radial die swell and velocity profiles of highly viscous fluids in an extrusion process. The variations in radial die swell profiles were explained in terms of changes in melt velocity, shear rate, and residence time at radial positions across the die. The radial die swell and velocity profiles for PS melt determined experimentally in this work were accurate to 92.2% and 90.8%, respectively. The overall die swell ratio of the melt ranged from 1.25 to 1.38. The overall die swell ratio was found to increase with increasing piston speed (shear rate). The radial extrudate swell profiles could not be reasoned by the shear rate change, but were closely linked with the development of the velocity profiles of the melt in the die. The die swell ratio was high at the center (～1.9) and low (～0.9) near the die wall. The die swell ratio at the center of the die reduced slightly as the piston speed was increased. Polym. Eng. Sci. 44:1960–1969, 2004. © 2004 Society of Plastics Engineers.     

Effects of die temperature on extrudate swell in screw extrusion

Extrusion of a hot polymer melt through a cooler die zone substantially increases the extrudate swell of some thermoplastics. This effect was examined for commercial samples of low-density polyethylene, polypropylene, and polystyrene. Two conflicting effects come into play during extrusion of a thermoplastic. Colder melt temperatures promote increased extrudate swell, but the same conditions also facilitate molecular disentanglement and reduced melt elasticity and die swell. Since the extrusion process itself may affect the relation between die swell and melt temperature, laboratory-scale measurements for the design of processes like blow molding are better carried out with small-scale screw extruders than with capillary rheometers. For some applications it may be advantageous to use a polymer whose die swell is particularly responsive or unresponsive to die temperature variations. The procedure described in this article can be used effectively to monitor this characteristic.     

聚己内酯的熔体流动性能和挤出胀大

应用熔体流动速率仪,在温度为90～140℃和载荷为2.16～12.50 kg的条件下,考察了温度、表观剪切速率(γα)及管壁剪切应力((Τ)R)对聚己内酯(PCL)熔体流动性能和挤出胀大比(B)的影响.结果表明:在实验条件下,PCL熔体的剪切流动基本服从幂律定律.表观剪切黏度ηa与绝对温度的关系符合Arrhenius方程,ηa随着γa或ΤR的增加而非线性减小.B随着温度的升高而非线性降低,随着γa或(Τ)R的增加而非线性增大,达到最大值后B则下降.     

Rheological properties,flow visualization and extrudate swell of NR compound by rotating‐die rheometer

An experimental apparatus coupled with a rotating die system was especially designed and manufactured to study the rheological properties, flow patterns and swelling behavior of natural rubber (NR) compound for different shear rates and die rotating speeds at a test temperature of 110°C, the results being compared with those by the static capillary die. It was found that NR compound used exhibited psuedoplastic non‐Newtonian behavior. The rotation of the capillary die could reduce the extrusion load. The wall shear stress for any given shear rates increased with increasing die rotating speed. The fluctuation of the entrance pressure drop increased with increasing die rotating speed. The flow pattern development in the rotating‐die rheometer was different from that observed in the static die. The flow patterns in the rotating die were clearly unstable and contained two flow components which included axial flow along the barrel and circumferential flow at the die entrance. The size and shape of the axial and circumferential flows were more dependent on the piston displacement. It was found that the swelling ratio of the NR compound decreased with increasing die rotating speed. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers.     

Experimental studies on extrudate swell behavior of PS and LLDPE melts in single and dual capillary dies

Extrudate swell behavior of polystyrene (PS) and linear low‐density polyethylene (LLDPE) melts was investigated using a constant shear rate capillary rheometer. Two capillary dies with different design configurations were used, one being a single flow channel and the other being a dual flow channel. A number of extrudate swell related parameters were examined, and used to explain the discrepancies in the extrudate swell results obtained from the single and dual flow channel dies, the parameters including output rate and output rate ratio, power law index, wall shear rate, wall shear stress, melt residence time, pressure drop induced temperature rise, flow channel position relative to the barrel centerline, and the flow patterns. It was found in this work that the power law index (n value) was the main parameter to determine the output rate ratio and the extrudate swell between the large and small holes for the dual flow channel die: the greater the n value the lower the output rate ratio and thus decreased extrudate swell ratio. The differences in the extrudate swell ratio and flow properties for PS and LLDPE melts resulted from the output rate ratio and the molecular chain structure, respectively. The extrudate swell was observed to increase with wall shear rate. The discrepancies in the extrudate swell results from single and dual dies for a given shear rate were caused by differences in the flow patterns in the barrel and die, and the change in the melt velocities flowing from the barrel and in the die to the die exit. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1713–1722, 2003     

The effct of asymmetries of die exit geometry on extrudate swell and melt fracture

Experimental investigations were performed to see how the die exit geometry and the extrusion velocity influence on extrudate swell and melt fracture for several polymer melts [low-density polyethylene, styrene-butadiene rubber (SBR) and SBR/HAF (carbon black) compound]. Four different types of die exit geometry were considered; 0° (symmetric. usual capillary die), and 30°, 45° and 60° (asymmetric dies) were chosen for the die exit angle. Extrudate diameters were measured without draw-down under isothermal condition. Polymer melts were extruded into an oil that has the same density and temperature as those of the extrudate. Extrudate swells from dies with different diameters were correlated with volumetric flow rates. It was observed that the extrudate swell increases with increasing volumetric flow rate and exhibits through a minimum value at about 45° die exit angle. As to the fracture phenomena, it was observed that the critical shear for the onset of melt fracture increases with the increasing die exit angle up to 45°. However, for 60° die exit angle, the onset of melt fracture is again similar to that of 0° exit angle.     

Flow visualization and extrudate swell of natural rubber in a capillary rheometer: Effect of die/barrel system

An investigation was carried out to examine the effect of die/barrel system on the flow patterns and extrudate swell of natural rubber in the barrel of a capillary rheometer, using a colored tracer as the visualization technique. The capillary rheometer used in this work had two dies located along the barrel, which is novel in rheometer design. The flow of the rubber in the upper barrel was dependent on the piston/barrel action and changed with piston displacement, whereas the complexity of the flow in the lower barrel was dependent not only on the piston displacement, but also on the geometry of the upper die design. The flow patterns that developed in the whole barrel were independent of the die located at the bottom of the barrel. In addition, the change in extrudate swell was associated with the flow occurring in the barrel, residence time, elastic characteristic, and the temperature rise during the flow. It was concluded that the general style of the flow patterns of natural rubber was greatly dependent on the die geometry that the material had previously moved past. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2525–2533, 2001     

Measurement and simulation of low‐density polyethylene extrudate swell through a circular die

BACKGROUND: Extrudate swell is a common phenomenon in polymer processing. The investigation of its mechanism is of both scientific and industrial interest. RESULTS: The rheological parameters of a material described by the viscoelastic PTT (Phan‐Thien–Tanner) constitutive model are obtained by fitting the distributions of material functions detected with a strain‐controlled rheometer. The swelling ratios of low‐density polyethylene (LDPE) under different volume flow rates are indirectly obtained using a photographic technique. A mathematical model of extrudate swell is established and its finite element model is derived. A penalty method is employed to solve the extrudate swell problem with a decoupled algorithm. Computation stability is improved by using the discrete elastic‐viscous split stress algorithm incorporating the inconsistent streamline‐upwind scheme. CONCLUSION: The swell phenomenon of LDPE through a circular die is investigated using both experimental measurement and numerical simulation. The swelling ratios obtained from the simulation are compared with those measured: they agree well with each other. The essential flow characteristics of polymer melts are predicted and the mechanism of the swell phenomenon is further discussed. Copyright © 2009 Society of Chemical Industry     

Experimental investigations of the influence of molecular weight distribution on melt spinning and extrudate swell characteristics of polypropylene

An experimental study of the influence of molecular weight distribution on the melt spinning and extrudate swell of a series of polypropylenes of varying molecular weight and distribution is reported. Emphasis is given to effects of variations of molecular weight distribution. Narrowing the molecular distribution increases the slope of the elongational viscosity–elongation rate curve, stabilizes the spinline relative to both random disturbances and draw resonance, and decreases both instantaneous and delayed extrudate swell. These results are interpreted in terms of viscoelastic fluid mechanics and earlier experimental studies by the authors of the influence of molecular weight distribution on rheological properties. The influences of these rheological factors on spinline structure development is discussed.     

Linear and nonlinear melt rheology and extrudate swell of acrylonitrile‐butadiene‐styrene and organoclay‐filled acrylonitrile‐butadiene‐styrene nanocomposite

Melt viscoelastic behavior and the die swell of Acrylonitrile‐Butadiene‐Styrene (ABS) and ABS/clay nanocomposites varying in organoclay loading were studied. A pronounced low‐frequency nonterminal behavior exhibited in linear viscoelastic experiments along with an apparent yield stress in transient startup flow tests suggested the existence of a network type, because of interconnection of rubber particles in ABS matrix. From the results of linear and nonlinear viscoelastic measurements, it was found that the incorporation of organoclay can lead to the formation of an additional network formed between organoclay tactoids that caused reduced temperature dependency of linear viscoelastic properties of the nanocomposite samples compared with ABS matrix. The swelling behavior of samples was interpreted using the results of stress relaxation experiments after cessation of steady shear flow. The great reduction in the die swell of nanocomposite samples could be explained in terms of great surface area and anisometric nature of organoclay tactoids and/or platelets, which promote energy consumption and less energy to be stored in chains. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Die design for rigid PVC—the effect of die land length on extrudate swell

PVC profile extrusion compounds have a unique morphology. While other polymers gradually decrease in extrusion die swell with increasing length/thickness (L/D) ratio, PVC profile extrusion compounds have a low die swell, quite independent of the die's L/D ratio in the range of 5 to 20. The fact that the die land length can be changed without changing the extrudate swell is an important consideration, which makes die design and balancing dies simpler and easier for PVC profile extrusion compounds. While other polymers substantially increase extrudate swell with increased shear rate, the swell of the PVC profile compounds is not much affected by shear or extrusion rate. This unique behavior allows wider processing latitude in profile extrusion and faster extrusion rates than with other polymers. Another unique factor in the rheology of PVC profile extrusion compounds is that extrusion die swell increases with increasing melt temperature, while other polymers have decreasing die swell with increasing melt temperature. The unusual rheology of PVC profile extrusion compounds is attributed to its unique melt morphology, where the melt flow units are 1 um bundles and molecules that have low surface to surface interaction and entanglement at low processing temperatures but increased melting and increased entanglement at higher processing temperatures. Other polymers, unlike PVC, have melt flow at the molecular level.     

Effect of process variables on melt velocity profiles in extrusion process using single screw plastics extruder

Abstract

Single screw extruders are used to generate a continuous flow of molten polymer in many industrial polymer processes. The melt velocity profile as extruded is important in determining the properties of the final product and influences process related phenomena such as die swell and the onset of sharkskin. The factors that influence the velocity profile would be expected to be the melt temperature (this affecting the viscosity of the melt), the screw and die geometry, and the output rate from the extruder. In the present work a thermocouple mesh sensor coupled with a cooled stainless tube has been used to determine velocity profiles in melts exiting from the screw of a single screw extruder. The results show that the technique can be used successfully to determine velocity profiles in the extrusion process.

It was found that the main influence on the magnitude of the melt velocity was the extruder screw speed. Melt temperature, and hence melt viscosity, were found to have little effect on the velocity profiles measured. The flow in the centre of the duct was retarded slightly owing to the flow across the screw tip and no rotational component of flow was observed. The velocity profiles measured seemed to be reasonably stable, only small changes being observed in the velocity profiles as the melt flowed along a duct of uniform cross-section, although these changes were limited in nature. Die diameter and length had a limited effect on the velocity profiles generated, although the die entry angle did have a significant effect on the shape of the velocity profile at higher screw speeds.     

影响挤出膨胀因数和收缩率的工艺及设备因素

阐明影响挤出胎面膨胀和收缩的主要工艺及设备因素是口型板的结构和尺寸,挤出条件以及设备。口型的冠部截面大,口型圆角Ｒ小,流胶口大,排胶温度高,挤出速度慢,则膨胀因数小,反之,膨胀因数大。冷却效果好,胎面稳定性高,收缩率小。认为：要减小胎面变形,口型总宽度应大于半成品总宽度。差值为３０￣５０ｍｍ,冠宽略小于半成品冠宽,差值为３￣１０ｍｍ;口型圆角Ｒ取值以２￣３ｍｍ为宜。     

Effect of die gap width on annular extrudates by the annular extrudate swell simulation in steady-states

We calculated the steady-state annular extrudate swell of polymer melts through flow geometries encountered in processes used to control parison thickness. A streamline-upwinding finite element method with an under-relaxation for the rate of deformation tensor was used. The Giesekus model was employed as the constitutive equation. An operation that widens the die gap is appropriate for the control of parison thickness corresponding to the change of die gap width. However, a control process that decreases the die gap width is not useful, because the parison thickness does not correspond to the die gap width. Furthermore, thickness swells change strikingly with the Weissenberg number. It is difficult to control the parison outer diameter in the case of a converging die, because the change of the outer diameter swell becomes large with increasing Weissenberg number. In the case of a diverging die, the changing value of the outer diameter swell is smaller than that in the case of a converging die.     

The application of an extrusion slit die in the rheological measurements of polyethylene composites with calcium carbonate using an in‐line rheometer

This article has reported the results of rheological testing of low‐density polyethylene (LDPE) and its calcium carbonate composites containing 7, 14, 21, and 28 wt% filler, respectively. The polymer composites were produced in a twin‐screw extrusion process. The assessment of the rheological properties of the polymeric materials was made under extrusion process conditions, using an in‐line rheometer with an extrusion slit die (W = 20, H = 2, L = 150 mm), at temperatures of 170°C, 180°C, and 190°C, respectively. The rheological parameters were determined based on the Ostwald‐de‐Waele power law model. The employed testing stand enabled the assessment of the effect of filler addition and slit die temperature on the variations in viscosity, power law index (n), consistency index (K), maximum flow velocity (V_max), and maximum flow profiles (V_z), under the conditions of technological processing (extrusion) of plastics. POLYM. ENG. SCI., 59:E16–E24, 2019. © 2018 Society of Plastics Engineers     

熔体层厚对聚合物共挤出胀大的影响

基于流变学理论和Phan-Thien-Tanne本构方程,建立了三维等温黏弹共挤成型流动过程的数值模型。运用有限元方法对数值模型进行了模拟计算,研究了熔体层厚对共挤成型的影响,分析了熔体层厚对挤出胀大率、偏转变形及界面形貌的影响。结果表明:熔体层厚对挤出胀大率和界面形貌的影响较大,随着熔体层厚的增加,挤出胀大率减小;随着共挤出熔体层厚差值的增大,界面形状趋于不稳定;熔体离开口模后产生低黏度熔体向高黏度熔体一侧偏转变形,但变形程度受熔体层厚的影响不大。     

Velocity measurements on a polypropylene melt during extrusion through a flat coat‐hanger die

An experimental investigation of various flow regimes observed during the extrusion of a polypropylene melt through a flat coat‐hanger die by laser‐Doppler velocimetry (LDV) is presented. LDV measurements of the velocity profiles across the gap of the die at various locations along the die reveal three different extrusion regimes. At small wall shear stresses, the velocity profiles can be fitted by symmetrical curves with the velocities becoming zero at the die walls. These profiles are not uniformly distributed along the die. An increase of the wall shear stress reveals a second flow regime characterized by a uniform distribution of the velocity profiles along the die. As the wall shear stress is increased even further, a third flow regime characterized by wall slip on the glass windows is observed. This flow regime is systematically characterized by measurements of the slip velocities at various temperatures and throughputs. The maximum velocities along the die are taken to assess the uniformity of flow which decisively influences the thickness of the extruded film. By measuring velocity profiles, at different throughput, and temperatures, the conditions for constant velocities along the die were determined. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Isothermal swell of extrudate from annular dies; effects of die geometry,flow rate,and resin characteristics

An experimental study was made of the effects of die geometry and extrusion velocity on parison swell for three high-density-polyethylene blowmolding resins. Four annular dies were used: a straight, a diverging, and two converging dies. Diameter and thickness swells were measured as functions of time under isothermal conditions and in the absence of drawdown. This was accomplished by extruding into an oil having the same density and temperature as the extrudate. It was observed that 60 to 80 percent of the swell occurs in the first few seconds and that equilibrium swell is attained only after 5 to 8 minutes have elapsed. The diameter and thickness swells appear to be independent phenomena, as the relationship between them depends strongly on die design. The ranking of the resins in terms of the magnitude of the swell was found to be the same for all die geometries and extrusion rates used.