Dielectric relaxation spectroscopy of poly[(R)‐3‐hydroxybutyrate] (PHB) during crystallization

The dielectric response of poly [(R)‐3‐hydroxybutyrate] (PHB) was investigated as a function of time after quenching a film from the melt to a crystallization temperature of 20 °C. In the frequency range investigated (20 to 10⁶ Hz) a relaxation maximum was observed–attributable to the glass transition–which could be analysed by the Havriliak–Negami relation. Changes in the complex dielectric constant were monitored both during spherulite growth (primary crystallization) and subsequently during a period of progressive crystallization (secondary crystallization) at room temperature. The relaxation strength changed only slightly during primary crystallization and its peak position remained at a constant frequency. Subsequently a continuous decrease in relaxation strength occurred, indicating considerable changes in molecular mobility after spherulite growth had been completed. The results provide further evidence that molecular mobility in the amorphous regions decreases significantly with time, and that this would be the reason why PHB shows embrittlement on ageing at room temperature. Copyright © 2004 Society of Chemical Industry     

Blends of bacterial poly[(R)‐3‐hydroxybutyrate] with oligo[(R,S)‐3‐hydroxybutyrate]‐diol

The miscibility, melting and crystallization behaviour of poly[(R)‐3‐hydroxybutyrate], PHB, and oligo[(R,S)‐3‐hydroxybutyrate]‐diol, oligo‐HB, blends have been investigated by differential scanning calorimetry: thermograms of blends containing up to 60 wt% oligo‐HB showed behaviour characteristic of single‐phase amorphous glasses with a composition dependent glass transition, T_g, and a depression in the equilibrium melting temperature of PHB. The negative value of the interaction parameter, determined from the equilibrium melting depression, confirms miscibility between blend components. In parallel studies, glass transition relaxations of different melt‐crystallized polymer blends containing 0–20 wt% oligo‐HB were dielectrically investigated between ?70 °C and 120 °C in the 100 Hz to 50 kHz range. The results revealed the existence of a single α‐relaxation process for blends, indicating the miscibility between amorphous fractions of PHB and oligo‐HB. © 2002 Society of Chemical Industry     

Recent developments in polymer applications of synchrotron small‐angle X‐ray scattering

Synchrotron radiation facilities have been established and become very familiar in the polymer community not only from academic but also industrial viewpoints. It is not so unusual now to conduct simultaneous measurements of small‐angle X‐ray scattering (SAXS) with other techniques such as wide‐angle X‐ray scattering, stress–strain, light scattering, and so forth. New techniques have also been established and have become more familiar in recent years. In this review, recent developments in polymer applications of synchrotron SAXS are summarized. Instrumental developments and progress in data analyses are reviewed from the following aspects: ultra‐small‐angle X‐ray scattering, anomalous SAXS, X‐ray photon correlation spectroscopy, new types of simultaneous measurements, grazing‐incidence SAXS, new trends in nanoparticle analyses and industrial applications. © 2016 Society of Chemical Industry     

Miscibility,thermal behaviour,morphology and mechanical properties of binary blends of poly[(R)‐3‐hydroxybutyrate] with poly(γ‐benzyl‐L‐glutamate)+

The miscibility, thermal behaviour, morphology and mechanical properties of poly[(R)‐3‐hydroxybutyrate] (PHB) with poly(γ‐benzyl‐L ‐glutamate) (PBLG) are investigated by means of differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and tensile tests. The DSC results show that PHB and PBLG are immiscible in the melt state. Such immiscibility also exists in the amorphous state due to a clear two‐phase separated structure observed by SEM measurements. The blend samples with different thermal history, namely as original and melt samples separately, display differences in thermal behaviour such as the DSC scan profile, the crystallinity and the melting temperature of PHB. The crystallization of PHB both from the molten state and the amorphous state is retarded on addition of the second component. The SEM measurements reveal that a phase inversion occurs between the PHB/PBLG (60/40) and PHB/PBLG (40/60) blends. Except for the PHB/PBLG (40/60) blend, a microphase separated structure is observed for all blend compositions. The mechanical properties vary considerably with blend composition. Compared with pure components, the PHB/PBLG (20/80) blend shows a certain improvement in mechanical properties. © 2001 Society of Chemical Industry     

Thermal and crystallization behavior of hydrogen‐bonded miscible blend of poly(3‐hydroxybutyrate) and enzymatically polymerized polyphenol

Enzymatically prepared novel polyphenol poly(4,4′‐dihydroxydiphenyl ether) (PDHDPE) is blended to modify the properties of biodegradable polyester poly[(R)‐3‐hydroxybutyrate] (PHB). Because the differential scanning calorimetry data show a single composition‐dependent glass transition for each blend, PHB and PDHDPE are found to be miscible in the amorphous phase. The crystallization of PHB is depressed by PDHDPE because PDHDPE reduces the molecular mobility and the flexibility of molecular chains of PHB. The Fourier transform IR spectra clearly indicate that PHB and PDHDPE interact through strong intermolecular hydrogen bonds between the carbonyl groups of PHB and the hydroxyl groups of PDHDPE. However, when PHB is blended with DHDPE monomer, no obvious hydrogen bonds are observed because of the phase separation and strong self‐intermolecular hydrogen bonds between DHDPE molecules. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2439–2449, 2005     

Synthesis and characterization of multi‐block copolymers containing poly [(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] and poly(ethylene glycol)

Various problems, including high crystallinity, high melting temperature, poor thermal stability, hydrophobicity and brittleness, have impeded many practical applications of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV) as an environmentally friendly material and biomedical material. In the work reported here, multi‐block copolymers containing PHBV and poly(ethylene glycol) (PHBV‐b‐PEG) were synthesized with telechelic hydroxylated PHBV as a hard and hydrophobic segment, PEG as a soft and hydrophilic segment and 1,6‐hexamethylene diisocyanate as a coupling reagent to solve the problems mentioned above. PHBV and PEG blocks in PHBV‐b‐PEG formed separate crystalline phases with lower crystallinity levels and lower melting temperatures than those of phases formed in the precursors. The crystallite dimensions of the two blocks in PHBV‐b‐PEG were smaller than those of the corresponding precursors. Compared to values for the original PHBV, the maximum decomposition temperature of the PHBV block in PHBV‐b‐PEG was 16.0 °C higher and the water contact angle was 9° lower. In addition, the elongation at break was 2.8% for a pure PHBV fiber but 20.9% for a PHBV/PHBV‐b‐PEG fiber with a PHBV‐b‐PEG content of 30%. PHBV‐b‐PEGs can overcome some of the disadvantages of pure PHBV; it is possible that PHBV might be a good candidate for the formulation of environmentally friendly materials and biomedical materials. Copyright © 2010 Society of Chemical Industry     

About the Lorentz correction used in interpretation of small‐angle X‐ray scattering data of semicrystalline polymers

Lorentz correction is used to correct the intensities of X‐ray scattering of single‐crystal diffractometry in order to recalculate intensities to obtain structure factors. This correction reduces the intensities to zero at zero diffraction angle. Small‐angle scattering is used to study the dimensions of heterogeneities in polymeric materials. The scattering intensities at a near to zero scattering angle originate partly from periodic systems (reciprocal lattice) and partly from dispersed particle systems. Periodic systems should result in individual Gaussian or Lorentzian peaks with the position of a peak maximum depending on the length of the periodicity. Particle scattering results in a Gaussian peak centered at zero scattering angle. The effect of the Lorentz correction on the interpretation of small‐angle X‐ray scattering data is shown for some semicrystalline polyethylenes (high‐density, linear low‐density, and low‐molecular‐weight waxy polyethylenes). The data are compared to those for amorphous block copolymers (styrene–butadiene), in which there is a periodic system with homogeneous lamellar thickness. Lorentz correction destroys the characteristics of the particle scattering and can be applied only for periodic systems. It should not be used to produce a peak on scattering data, which do not show periodicity (peaks) without correction. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 358–366, 2001     

Microfocus small‐angle X‐ray scattering investigation of the skin–core microstructure of lyocell cellulose fibers

Skin–core microstructures in hydrated lyocell cellulose fibers were investigated using microfocus small‐angle X‐ray scattering (SAXS). Both single fibers and fiber cross sections were observed. In all the fibers studied, a thin skin layer was observed in which the voids were smaller in cross section and better oriented than those in the core. The division between skin and core may not be sharp. A draw ratio of 0.80 gave fibers with voids that were shorter, larger in cross section, and more misoriented than the fibers produced with a draw ratio of 1.68. In contrast, there was little difference in void structure between samples coagulated in water and in 25% amine oxide aqueous solution. The results are explained in the context of the spinodal decomposition, which is thought to occur during coagulation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2799–2816, 2002; DOI 10.1002/app.10256     

Crosslinking of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] using dicumyl peroxide as initiator

In order to modify poly [(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV), the crosslinking of this copolymer was carried out at 160 °C using dicumyl peroxide (DCP) as the initiator. The torque of the PHBV melt showed an abrupt upturn when DCP was added. Appropriate values for the gel fraction and crosslink density were obtained when the DCP content was up to 1 wt% of the PHBV. According to the NMR spectroscopic data, the location of the free radical reaction was determined to be at the tertiary carbons in the PHBV chains. The melting point, crystallization temperature and crystallinity of PHBV decreased significantly with increasing DCP content. The effect of crosslinking on the melt viscosity of PHBV was confirmed as being positive. Moreover, the mechanical properties of PHBV were improved by curing with DCP. When 1 wt% DCP was used, the ultimate elongation of PHBV increased from 4 to 11 %. A preliminary biodegradation study confirmed the total biodegradability of crosslinked PHBV. Copyright © 2004 Society of Chemical Industry     

Poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)]/layered double hydroxide nanocomposites

BACKGROUND: The thermomechanical performance of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV) is associated with its crystallization. Enhanced nucleation using a stearate‐functionalized synthetic layered double hydroxide (LDH) presents a potential solution. RESULTS: PHBV crystallization varied with concentration of LDH. At lower LDH concentration, thermal history‐induced cold crystallization was present. The extent of this order–disorder transition decreased with increasing LDH concentration and was completely eliminated at 7 wt% LDH. PHBV did not have a melt recrystallization peak but the introduction of LDH resulted in an increasingly pronounced melt recrystallization with increasing LDH concentration. Polarized optical microscopy coupled with differential scanning calorimetry and wide angle X‐ray diffraction (WAXD) analysis indicated increased lamella thickness in the nanocomposites compared to pure PHBV. WAXD and transmission electron microscopy showed that the nanocomposites had an intercalated but aggregated dispersion. CONCLUSION: The concentration of nanofiller provides unique effects in PHBV. Mechanical performance was found to scale with composition as determined using dynamic mechanical analysis and tensile testing. Copyright © 2008 Society of Chemical Industry     

Water transport properties in poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) biopolymers

Water sorption and diffusion have been investigated in poly(3‐hydroxybutyrate) (PHB) and three poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) copolymers [P(HB‐HV)] by means of a Cahn electromicrobalance. Permeability of these samples have been determined using a gravimetric permeation cell. Two experimental setups were used for the gravimetric sorption measurements, under dynamic and static conditions, respectively. The differences observed in the results obtained using these techniques are discussed. The sorption measurements have evidenced the tendency of water molecules to form aggregates or clusters in the polymer. In addition, the static sorption method revealed the potential of PHB and P(HB‐HV) to undergo molecular relaxations, eventually leading to a partial desorption of the previously sorbed water after an induction period. The clustering effect was adequately described by the polycondensation model. On the other hand, the interpretation of the diffusivity in terms of mobility coefficients has revealed a competition between a plasticization effect and clustering. As a whole, water transport properties in PHB and its copolymers can be considered to be very close in magnitude to those of common thermoplastics such as PVC and PET. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 455–468, 1999     

Thermogravimetric analysis of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The thermal degradation of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐HV)] was studied using thermogravimetry (TG). In the thermal degradation of PHB, the temperature at the onset of weight loss (T_o) was derived by T_o = 0.97B + 259, where B represents the heating rate (°C/min). The temperature at which the weight loss rate was maximum (T_p) was T_p = 1.07B + 273, and the final temperature (T_f) at which degradation was completed was T_f = 1.10B + 280. The percentage of the weight loss at temperature T_p (C_p) was 69 ± 1% whereas the percentage of the weight loss at temperature T_f (C_f) was 96 ± 1%. In the thermal degradation of P(HB‐HV) (7:3), T_o = 0.98B + 262, T_p = 1.00B + 278, and T_f = 1.12B + 285. The values of C_p and C_f were 62 ± 7 and 93 ± 1%, respectively. The derivative thermogravimetric (DTG) curves of PHB confirmed only one weight loss step change because the polymer mainly consisted of the HB monomer only. The DTG curves of P(HB‐HV), however, suggested multiple weight loss step changes; this was probably due to the different evaporation rates of the two monomers. The incorporation of 10 and 30 mol % of the HV component into the polyester increased the various thermal temperatures (T_o, T_p, andT_f) by 7–12°C (measured at B = 20°C/min). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2237–2244, 2001     

Fast crystallization of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with talc and boron nitride as nucleating agents

The crystallization behavior of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) induced by two kinds of nucleating agents, boron nitride (BN) and talc, was investigated by differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both BN and talc have good nucleating ability in the crystallization of PHB and PHBV. From these results, combined with molecular weight measurement by gel permeation chromatography, the mechanism of nucleation by BN and talc in the crystallization of PHB and PHBV has been proposed. BN acts as a nucleating agent itself and initiates nucleation in the crystallization of PHB and PHBV. Talc acts in a different way. It reacts as a chemical reagent with the molten chains of PHB/PHBV, while the reaction product acts as the true nucleating agent, which lowers the crystallization barriers of PHB and PHBV. ¹H NMR spectroscopy provides evidence for the reaction between PHB and talc and supports the proposed nucleation mechanism. Copyright © 2005 Society of Chemical Industry     

The kinetics of the thermal decomposition of poly(3‐hydroxybutyrate) and maleated poly(3‐hydroxybutyrate)

The thermal decomposition mechanism of maleated poly(3‐hydroxybutyrate) (PHB) was investigated by FTIR and ¹H NMR. The results of experiments showed that the random chain scission of maleated PHB obeyed the six‐membered ring ester decomposition process. The thermal decomposition behavior of PHB and maleated PHB with different graft degree were studied by thermogravimetry (TGA) using various heating‐up rates. The thermal stability of maleated PHB was evidently better than that of PHB. With increase in graft degree, the thermal decomposition temperature of maleated PHB gradually increased and then declined. Activation energy E_a as a kinetic parameter of thermal decomposition was estimated by the Flynn‐Wall‐Ozawa and Kissinger methods, respectively. It could be seen that approximately equal values of activation energy were obtained by both methods. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1789–1796, 2002; DOI 10.1002/app.10463     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

Carbon dioxide sorption and diffusion in poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐CO‐3‐hydroxyvalerate)

CO₂ sorption and diffusion in poly(3‐hydroxybutyrate) and three poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) copolymers were investigated gravimetrically at temperatures from 25° to 50°C and pressures up to 1 atm. The sorption behavior proved to be linear for all the copolymers studied. An additional set of measurements performed in a pressure decay apparatus at 35°C showed that the linearity could be extrapolated to pressures up to 25 atm. The sorption results obtained from both techniques were in good agreement. The poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) sorption kinetics were increasingly non‐Fickian at the higher temperatures, thus preventing the calculation of diffusion coefficients above 35°C. Interestingly, this was not the case for poly(3‐hydroxybutyrate), and diffusion coefficients and permeabilities could be calculated at all of the investigated temperatures. The 35°C permeabilities were fairly low, which is attributed to the high degree of crystallinity of this polyester family. Finally, the poly(3‐hydroxybutyrate) barrier properties against CO₂ are successfully compared with those of some selected common thermoplastics. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2391–2399, 1999     

Synthesis and characterization of maleated poly(3‐hydroxybutyrate)

Graft copolymerization of maleic anhydride (MA) onto poly(3‐hydroxybutyrate) (PHB) was carried out by use of benzoyl peroxide as initiator. The effects of various polymerization conditions on graft degree were investigated, including solvents, monomer and initiator concentrations, reaction temperature, and time. The monomer and initiator concentrations played an important role in graft copolymerization, and graft degree could be controlled in the range from 0.2 to 0.85% by changing the reaction conditions. The crystallization behavior and the thermal stability of PHB and maleated PHB were studied by DSC, WAXD, optical microscopy, and TGA. The results showed that, after grafting MA, the crystallization behavior of PHB was obviously changed. The cold crystallization temperature from the glass state increased, the crystallization temperature from the melted state decreased, and the growth rate of spherulite decreased. With the increase in graft degree, the banding texture of spherulites became more distinct and orderly. Moreover, the thermal stability of maleated PHB was obviously improved, compared with that of pure PHB. Its thermal decomposition temperature was enhanced by about 20°C. In addition, the introduction of the MA group promoted the biodegradability of PHB. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 659–668, 2003     

Structure and characterization of poly[(vinylidene fluoride)‐co‐hexafluoropropene]–(dibutyl phthalate) blends

Blends of poly[(vinylidene fluoride)‐co‐hexafluoropropene] with dibutyl phthalate were examined by wide‐ and small‐angle X‐ray scattering, differential scanning calorimetry and dynamic mechanical spectroscopy, in order to study the influence of amount of plasticizer and the crystallization rate on the crystallinity and lamellar morphology of the copolymer. The dibutyl phthalate seems, at least for the cooling and heating rates used, simply to dilute the crystalline phase without affecting the amount of polymer that is able to crystallize. Furthermore, the small‐angle X‐ray scattering technique points out that the plasticizer mostly enters the amorphous phase either outside or inside the lamellar stacks. © 2001 Society of Chemical Industry     

Crystallization of poly(3‐hydroxybutyrate) by exfoliated graphite nanoplatelets

Poly(3‐hydroxybutyrate) (PHB) has been shown to be efficiently nucleated by exfoliated graphite nanoplatelets (xGnP). The nucleating effect of xGnP was investigated using differential scanning calorimetry, optical microscopy and atomic force microscopy. Nonisothermal crystallization of PHB from the melt required lower activation energies for PHB containing 1 wt % and 3 wt % xGnP (?214 and ?102 kJ/mol respectively) than for pure PHB (?60 kJ/mol). A kinetic study of the PHB/xGnP crystallization employing a modified form of the Avrami equation revealed that the presence of xGnP increased the PHB crystallization temperature, as well as the crystallization rates, and generated smaller and more numerous spherulites. Optical microscopy and atomic force microscopy confirmed the incorporation of xGnP into the lamellar structure of the PHB spherulites and provided insight into the influence of xGnP on spherulite size and lamellae thickness. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Small‐angle X‐ray scattering investigation of the deformation processes in the amorphous phase of high density polyethylene

In situ small‐angle X‐ray scattering of high density polyethylene under uni‐axial tensile test was used for investigating the deformation at the scale of the periodic crystalline–amorphous nano‐structure. The more or less uniform elastic straining of the rubbery amorphous layers is discussed in terms of mechanically active intercrystalline tie chains. Correlation is made with the long‐term use properties. It is concluded that this approach is a powerful means to assess the mechanical efficiency of tie molecules. Copyright © 2004 Society of Chemical Industry