Preparation and characterization of thermosensitive poly(N‐isopropylacrylamide)/poly(ethylene oxide) semi‐interpenetrating polymer networks

Temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels were successfully synthesized by using poly(ethylene oxide) as the interpenetrating agent. The newly prepared semi‐interpenetrating polymer network (semi‐IPN) hydrogels exhibited much better properties as temperature‐sensitive polymers than they did in the past. Characterizations of the IPN hydrogels were investigated using a swelling experiment, FTIR spectroscopy, and differential scanning calorimetry (DSC). Semi‐IPN hydrogels exhibited a relatively high temperature dependent swelling ratio in the range of 23–28 at room temperature. DSC was used for the determination of the lower critical solution temperature of the semi‐IPN hydrogel. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3032–3036, 2003     

Electrospinning of Colloidal Lignin in Poly(ethylene oxide) N,N‐Dimethylformamide Solutions

Electrospinning of sulfur‐free softwood lignin (SFSL) in N,N‐dimethylformamide (DMF) is reported as is and with poly(ethylene oxide) (PEO). SFSL macromolecules behave as rigid spheres, instead of free draining macromolecules in DMF. Hence they are investigated as colloids. Colloidal SFSL generates uniform fibers only at the volume fraction of 0.63. It is due to the sufficiently high longest mean relaxation time at the volume fraction of 0.63. Colloidal SFSL below the volume fraction of 0.63 does not exhibit any measurable viscoelasticity and also does not generate any uniform fibers. Bead‐free fibers are generated at volume fractions below 0.63 only by adding PEO. PEO presence brings elasticity to colloidal SFSL and produces bead‐free fibers only above the entanglement concentration of PEO in DMF. The presence of SFSL macromolecules does not cause any interactions with PEO molecules, except it reduces the available of free volume for PEO chains in DMF.

     

Hydrogel of Radiation‐Induced Cross‐Linked Hydroxypropylcellulose

Hydroxypropylcellulose (HPC) hydrogel being a material of natural origin, combines the properties of a polymer, which make up the network, with biodegradability. In this report the effects of high energy radiation on the ether of cellulose‐HPC are presented. The polymer irradiated in its solid state or in dilute aqueous solution underwent mainly degradation, induced by the cleavage of glycosidic bonds in its main chain. Irradiation of HPC in aqueous solutions at moderate concentrations resulted in the formation of hydrogels. Chemical cross‐links bond the chains of polymer, turning it to an insoluble macroscopic gel. We have found that in addition to concentration, dosage and dose rate can affect the results of irradiation. Electron beam irradiation gave higher gel fraction, up to 90%, than gamma irradiation, which has a maximum gel fraction of 65%. Swelling of the cross‐linked hydrogels was related to the density of cross‐links and was the highest at low irradiation doses. HPC hydrogels displayed thermally reversible character in their swelling. The volume of gel underwent continuous deswelling with an increase of the solution temperature, with the deswelling rate increasing rapidly over 40°C. At elevated temperatures the hydrogel collapsed, lost its transparency and changed color to translucent white. This transition was fully reversible when the gel was placed in the medium of low temperature. The hydrogel demonstrated superior mechanical properties. Despite of the stable three‐dimensional cross‐linked network, the gels underwent biodegradation under controlled conditions when enzyme was used.     

Thermal characterizations of semi‐interpenetrating polymer networks composed of poly(ethylene oxide) and poly(N‐isopropylacrylamide)

Poly(N‐isopropylacrylamide) (PNIPAAm)/poly(ethylene oxide) (PEO) semi‐interpenetrating polymer networks (semi‐IPNs) synthesized by radical polymerization of N‐isopropylacrylamide (NIPAAm) in the presence of PEO. The thermal characterizations of the semi‐IPNs were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). The melting temperature (T_m) of semi‐IPNs appeared at around 60°C using DSC. DEA was employed to ascertain the glass transition temperature (T_g) and determine the activation energy (E_a) of semi‐IPNs. From the results of DEA, semi‐IPNs exhibited one T_g indicating the presence of phase separation in the semi‐IPN, and T_gs of semi‐IPNs were observed with increasing PNIPAAm content. The thermal decomposition of semi‐IPNa was investigated using TGA and appeared at around 370°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3922–3927, 2003     

New aqueous two‐phase systems based on poly(ethylene oxide sulfide) (PEOS) and potassium phosphate for the potential recovery of proteins

A new aqueous two‐phase system (ATPS) based on a degradable polymer called poly(ethylene oxide sulfide) with a molecular weight of 33 000 g mol^?1 (identified as PEOS‐12) and potassium phosphate was exploited for the potential recovery of proteins. An initial characterisation of the ATPS was achieved by the construction of a phase diagram for the PEOS‐12/phosphate system. The protein partitioning behaviour of lysozyme and bovine serum albumin (BSA), selected as single model proteins, and B‐phycoerythrin (BPE) produced by Porphyridium cruentum in the new ATPS under increasing tie line length (TLL) conditions at constant phase volume ratio (V_r) and system pH was investigated. Both single proteins partitioned in the new ATPS, initially exhibiting bottom phase preference; however, lysozyme changed phase preference when TLL was increased. Fractionation of a complex model (production of BPE by P. cruentum) using PEOS‐12/phosphate ATPS was performed to evaluate the potential protein recovery from fermentation broth or cell homogenate. The proposed new ATPS proved to be suitable for the potential recovery of BPE from crude extract of P. cruentum. In general, a system comprising V_r = 1.0, 18% (w/w) PEOS‐12, 8% (w/w) phosphate and 30% (w/w) TLL at pH 7.0 provided conditions to concentrate BPE into the bottom phase (i.e. partitioning behaviour of BPE; lnK_BPE = ?1.8) with a protein recovery of 84%. The findings reported here demonstrate the potential application of the new ATPS for the recovery of proteins from complex biological suspensions. Copyright © 2006 Society of Chemical Industry     

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide) and poly(propylene oxide)

Phase behavior of aqueous systems containing block copolymers of poly(ethylene oxide (PEO) and poly(propylene oxide) (PPO) was evaluated by building up temperature-concentration phase diagrams. We have studied bifunctional triblock copolymers (HO-PEO-PPO-PEO-OH) and monofunctional diblock copolymers (R-PEO-PPO-OH and R-PPO-PEO-OH, where R length is linear C₄ and C_12–14). The cloud points of the polymer solutions depended on EO/PO ratio, polarity, R length and position of the hydrophilic and hydrophobic segments along the molecule. Such factors influence on the solutions behavior was also analyzed in terms of critical micelle concentration (CMC), which was obtained from surface tension vs. concentration plots. Salts (NaCl and KCl) added into the polymer solutions change the solvent polarity decreasing the cloud points. On the other hand, the cloud points of the polymer solutions increased as a hydrotrope (sodium p-toluenesulfonate) was added. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1767–1772, 1997     

Phase Behaviour of Poly(ethylene oxide)/Poly(styrene-co-maleic anhydride) Blends

Thermal behaviour and morphology of blends of poly(ethylene oxide) (PEO) and poly(styrene-co-maleic anhydride) (SMA) prepared by the coprecipitation technique were studied by means of differential scanning calorimetry, optical microscopy and thermogravimetry. SMA containing 25wt% maleic anhydride (MA) was found to be miscible with PEO when the SMA content was greater than 80%. The melting temperature and crystallinity depended on the composition of the blend. SMA appears to segregate interlamellarly during the isothermal crystallization of PEO. The thermal stability of blends was enhanced and was higher than that of pure PEO and SMA. © of SCI.     

Fire Retardance in Poly(butylene terephthalate). The Effects of Red Phosphorus and Radiation‐Induced Cross‐Links

Summary: The combustion performance of poly(butylene terephthalate) (PBT) can be improved by the addition of red phosphorus provided it is intermolecularly cross‐linked upon irradiation with ⁶⁰Co γ‐rays in the presence of triallyl cyanurate (TAC). At a content of 3 or 4 wt.‐% the latter significantly promotes cross‐linking in the presence of air. From combustion tests with samples containing red phosphorus (P_red) and having been γ‐irradiated in the presence of TAC it turned out that an improved fire resistance of PBT is achieved if the red phosphorus content is at least 12.5 wt.‐%. In this case test samples were self‐extinguishing and the UL 94 rating corresponded to V‐1. Product analysis and thermal gravimetric analysis revealed that P_red stimulates aromatization and charring. These processes involve the reaction of P_red with the polymer. ³¹P NMR spectroscopy revealed that the residue contained chemically bonded phosphorus.

Decomposition of anhydride groups resulting in phenyl radicals.     

Properties of Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline Conductive Films: The Effect of Poly(ethylene glycol) Diglycidyl Ether

The effect of polyaniline and poly(ethylene glycol) diglycidyl ether on tensile properties, morphology, thermal degradation, and electrical conductivity of poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films was studied. The poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films were prepared using a solution casting technique at room temperature until a homogeneous solution was produced. Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline/poly(ethylene glycol) diglycidyl ether conductive films exhibit higher electrical properties, tensile strength, modulus of elasticity but lower final decomposition temperature than poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films. Scanning electron microscopy morphology showed that the polyaniline more widely dispersed in the poly(vinyl chloride)/poly(ethylene oxide) blends with the addition of poly(ethylene glycol) diglycidyl ether as surface modifier.     

In‐Situ Fiberized Poly(ethylene terephthalate) as a Reinforcement to Poly(propylene) Matrix

The reinforced poly(propylene) (PP)/poly(ethylene terephthalate) (PET) in‐situ fiberized composites were prepared by extrusion‐drawing‐injection molding. The influences of PET weight fraction (f_w) on the PET fiberization, phase morphology, and mechanical properties of the composites, together with their functional mechanisms were studied by contrast to the normal‐blended materials without drawing. The results show that as the f_w rises from 0 to 20%, the number of PET fibers increases, whereas their diameter and dispersity decrease till f_w = 15% and then increase, and the number of remained PET particles tends to rise. These changes of PET fiberization and phase morphology with f_w were attributed to the consequence of the combined actions of breakup, coalescence, and deformation of the PET dispersed phase in the PP matrix during the extrusion drawing. Correspondingly, the tensile strength (σ_t) and Young's modulus (E) of the in‐situ composites increase till f_w = 15% and then decrease, with maximum gains of σ_t and E of about 20 and 70% relative to the neat PP, respectively. This σ_t/f_w relation was ascribed to the counterbalanced result between the reinforcing effect of the dispersed phase on matrix and the interfacial flaw effect of two immiscible phases, while the E/f_w relation was considered as a representation of the rigidizing effect of the fibers on the matrix being controlled by both their number and diameter.

In‐situ PET fibres (PET/PP = 85/15) in an as‐drawn filament.     

Poly(ethylene oxide)–polyelectrolyte blends: viscometric and thermal analysis behaviour

The miscibility of binary poly(ethylene oxide) (PEO) and sodium poly(4‐styrene sulphonate) (PSS) or [3,6]‐ionene (ION) systems, was analysed in aqueous solutions and in the solid state by viscometry and thermal analysis, respectively. Both techniques indicate partial miscibility of PEO–PSS and immiscibility of PEO–ION blends. In water solution, the partial miscibility of the PEO–PSS system is probably due to the counterion Na⁺ which can partially provide the driving force association in a similar manner to that observed for PEO–surfactant systems. In blend films, the PEO–polyelectrolyte interaction is also analysed in terms of the effect on the PEO crystallization observed through optical microscopy, and the results indicate compatibility between the components in the PEO–PSS system. © 2000 Society of Chemical Industry     

Ultraviolet-induced crosslinking of solid poly(ethylene oxide)

Poly(ethylene oxide) (PEO) of molecular weight from 200,000 to 2,000,000 was crosslinked by exposure to ultraviolet radiation with a high-pressure 150 W mercury lamp. Photochemical crosslinking of PEO proceeds in the presence of photoinitiators such as benzophenone and acetophenone which act as a hydrogen-abstracting agent. Gel fraction yield exceeds 90%, and the number-average molecular weight between crosslinks determined by equilibrium swelling in chloroform varies from 3,000 to 100,000. The degree of crosslinking can be controlled by changing the irradiation temperature. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 2299–2307, 1997     

Fractional Crystallization Kinetics of Poly(ethylene oxide) in Its Blends with Poly(butylene succinate): Molecular Weight Effects

The fractional crystallization kinetics and phase behavior of PEO with different molecular weights (MWs) in its miscible crystalline/crystalline blends with PBS are studied. Both fractional crystallization kinetics and phase segregation of PEO in PBS/PEO blends are dramatically influenced by its MW. PEO with a medium MW (20 kDa) shows a significant fractional crystallization in the blends with PBS crystallized at a high T_IC,PBS, which, however, is dramatically depressed in the blends with a very low or high MW of PEO. This indicates that the PEO component with a medium MW is more ready to segregate into the interlamellar region of PBS crystals than those with a very low or high MW. The MW‐dependent fractional crystallization kinetics and phase segregation of PEO component in the PBS/PEO blends are discussed.

     

Microwave‐assisted preparation of temperature sensitive poly(N‐isopropylacrylamide) hydrogels in poly(ethylene oxide)‐600

In this article, a series of poly(N‐isopropylacrylamide) (PNIPAM)‐based hydrogels were prepared under microwave irradiation using poly(ethylene oxide)‐600 (PEO‐600) as reaction medium and microwave‐absorbing agent as well as pore‐forming agent. All of the temperature measurements, gel fractions, and FTIR analyses proved that the PNIPAM hydrogels were successfully synthesized. Within 1 min, the PNIPAM hydrogel with a 98% yield was obtained under microwave irradiation. The PNIPAM hydrogels thus prepared exhibited controllable properties such as pore size, equilibrium swelling ratios, and swelling/deswelling rates when changing the feed weight ratios of monomer (N‐isopropylacrylamide, NIPAM) to PEO‐600. These properties are well adapted to the different requirements for their potential application in many fields such as biomedicine. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4177–4184, 2006     

Poly(ethylene terephthalate‐co‐isophthalate) copolyesters obtained from ethylene terephthalate and isophthalate oligomers

A series of poly(ethylene terephthalate‐co‐isophthalate) copolyesters containing upto 50%‐mole of isophthalic units were prepared by polycondensation from ethylene terephthalate and ethylene isophthalate fractions of linear oligomers containing from 5 to 6 repeating units in average. The polyesters were obtained in good yields and with high‐molecular‐weights. The microstructure of the copolyesters was studied as a function of reaction time by ¹³C‐NMR showing that a random distribution of the comonomers was achieved since the earlier stages of polycondensation. The melting temperature and enthalpy of the copolyesters decreased with the content of isophthalic units so that copolyesters containing more than 25% of these units were amorphous. Isothermal crystallization studies made on crystalline copolyesters revealed that the crystallization rate of copolyesters decreased with the content in isophthalic units. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Well‐Defined Poly(ethylene glycol) Hydrogels with Enhanced Mechanical Performance Prepared by Thermally Induced Copper‐Catalyzed Azide–Alkyne Cycloaddition

Poly(ethylene glycol) (PEG)‐based hydrogels have attracted increasing attention in recent years due to their good biocompatibility and low cost. However, the PEG‐based hydrogels prepared by traditional methods exhibit a poor machinability due to their disordered network structure. Herein, the preparation of well‐defined PEG‐based hydrogel via a facile thermally induced copper‐catalyzed azide–alkyne cycloaddition (CuAAC) reaction is demonstrated. To accomplish this, thermochemically reduced Cu(I) catalyst is adopted to trigger “click” cross‐linking, resulting in a well‐defined PEG network. The as‐synthesized PEG‐based hydrogel exhibits good mechanical performance with a tensile strength of 2.51 MPa, which is higher than the traditional PEG‐based hydrogels prepared from CuSO₄/NaSac‐mediated or CuBr/ligand‐catalyzed CuAAC. Moreover, in vitro cytotoxicity and in vivo porcine subcutaneous implantation tests demonstrate that the as‐synthesized PEG‐based hydrogel has a good biocompatibility and low toxicity, making it a promising candidate for the applications in biomedical devices and tissue engineering.

     

Preparation and characterizations of interpenetrating polymer network hydrogels of poly(ethylene oxide) and poly(methyl methacrylate)

Interpenetrating polymer network (IPN) hydrogels based on poly(ethylene oxide) and poly(methyl methacrylate) were prepared by radical polymerization using 2,2‐dimethyl‐2‐phenylacetophenone and ethylene glycol dimethacrylate as initiators and crosslinkers, respectively. The IPN hydrogels were analyzed for sorption behavior at 25°C and at a relative humidity of 95% using dynamic vapor sorption. The IPN hydrogels exhibited a relatively high equilibrium water content in the range of 13–68%. The state of water in the swollen IPN hydrogels was investigated using differential scanning calorimetry. The free water in the hydrogels increased as the hydrophilic content increased. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 258–262, 2003     

Synthesis and properties of hydrophilic segmented block copolymers based on poly(ethylene oxide)‐ran‐poly(propylene oxide)

The present article discusses the synthesis and various properties of segmented block copolymers with random copolymer segments of poly(ethylene oxide) and poly(propylene oxide) (PEO‐r‐PPO) together with monodisperse amide segments. The PEO‐r‐PPO contained 25 wt % PPO units and the segment presented a molecular weight of 2500 g/mol. The synthesized copolymers were analyzed by differential scanning calorimetry, Fourier transform infra‐red spectroscopy, atomic force microscopy and dynamic mechanical thermal analysis. In addition, the hydrophilicity and the contact angles (CAs) were studied. The PEO‐r‐PPO segments displayed a single low glass transition temperature, as well as a low PEO crystallinity and melting temperature, which gave enhanced low‐temperature properties of the copolymer. The water absorption values remained high. In comparison to mixtures of PEO/PPO segments, the random dispersion of PPO units in the PEO segments was more effective in reducing the PEO crystallinity and melting temperature, without affecting the hydrophilicity. Increasing the polyether segment length with terephthalic groups from 2500 to 10,000 g/mol increased the hydrophilicity and the room temperature elasticity. Furthermore, the CAs were found to be low 22–39° and changed with the crosslink density. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci 117:1394–1404, 2010     

Surface immobilization of star‐shaped poly(ethylene oxide) on poly(dimethylsiloxane)

A thin layer of star‐shaped poly(ethylene oxide) (PEO) (starPEO), on the polydimethylsiloxane (PDMS) membrane was prepared by a simple immobilization procedure. Photoreactive molecules were introduced on the surface of the polymeric support to achieve the formation of thin starPEO film from the materials having no functional groups. This novel technique enabled us to immobilize any kind of chemical, especially one that had no functional groups, and readily to control the amount of immobilization. The gas permeation properties of the starPEO‐immobilized PDMS membranes were investigated for pure propane and propylene. The permeance of gases were found to decrease in the starPEO‐immobilized PDMS membranes, although the ideal separation factors for propylene/propane were increased with the loading amount of silver ions, because of the facilitation action of silver ions in the immobilized PEO unit on the PDMS membranes, as propylene carriers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2369–2373, 2002     

Crystallization and melting behavior of blends comprising poly(3‐hydroxy butyrate‐co‐3‐hydroxy valerate) and poly(ethylene oxide)

Blends of poly(3‐hydroxy butyrate‐co‐3‐hydroxy valerate) (PHBV) and poly(ethylene oxide) (PEO) were prepared by casting from chloroform solutions. Crystallization kinetics and melting behavior of blends have been studied by differential scanning calorimetry and optical polarizing microscopy. Experimental results reveal that the constituents are miscible in the amorphous state. They form separated crystal structures in the solid state. Crystallization behavior of the blends was studied under isothermal and nonisothermal conditions. Owing to the large difference in melting temperatures, the constituents crystallize consecutively in blends; however, the process is affected by the respective second component. PHBV crystallizes from the amorphous mixture of the constituents, at temperatures where the PEO remains in the molten state. PEO, on the other hand, is surrounded during its crystallization process by crystalline PHBV regions. The degree of crystallinity in the blends stays constant for PHBV and decreases slightly for PEO, with ascending PHBV content. The rate of crystallization of PHBV decreases in blends as compared to the neat polymer. The opposite behavior is observed for PEO. Nonisothermal crystallization is discussed in terms of a quasi‐isothermal approach. Qualitatively, the results show the same tendencies as under isothermal conditions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2776–2783, 2006