The effect of annealing on the photoluminescence of layered perovskite H1.77[Sr0.8Bi0.21Ta2O7] powders

The microstructural and luminescent properties of H_1.77[Sr_0.8Bi_0.21Ta₂O₇] powders under different dehydrating conditions were investigated. The powders were obtained by protonating Bi₂SrTa₂O₉ powders in 3 M aqueous HCl solution, and were dehydrated by a post-annealing in air from 250 to 700 °C. The photoluminescence was enhanced for all dehydrated powders, especially for the sample annealed at 400 °C. The thermogravimetric analysis showed that there is an obvious dehydration temperature range from 200 to 400 °C, which was corresponding to the changing of the microstructure and photoluminescence in the same temperature range. The mechanism behind the experimental results was discussed.     

Synthesis reactions for Ti3SiC2 through pulse discharge sintering TiH2/Si/TiC powder mixture

Ternary compound Ti₃SiC₂ was rapidly synthesized by pulse discharge sintering the powder mixture of 1TiH₂/1Si/1.8TiC without preliminary dehydrogenation. Almost single-phase dense Ti₃SiC₂ was synthesized at 1400 °C for 20 min. The grain size of synthesized Ti₃SiC₂ strongly depends on sintering temperature. The synthesis mechanism of Ti₃SiC₂ was revealed to be completed via the reactions among the intermediate phases of Ti₅Si₃, TiSi₂ and the other reactants in the starting powder. The Ti-Si liquid reaction occurring above the Ti-Ti₅Si₃ eutectic temperature at 1330 °C was found to assist the synthesis reaction and densification of Ti₃SiC₂. The dehydrogenation of TiH₂ was accelerated by the synthesis reactions.     

Polycarbosilane derived Ti3SiC2

Titanium silicon carbide (Ti₃SiC₂) ceramic was synthesized by in-situ reaction of metal titanium and polycarbosilane. Reaction mechanisms which lead to the formation of Ti₃SiC₂ were suggested on the basis of XRD analysis. The content of Ti₃SiC₂ reached 93% in products obtained from heating the Ti/polycarbosilane green compact at 1400 °C in Ar. The morphology and compositions of the products were examined by SEM equipped with EDX. The typical laminate structure of Ti₃SiC₂ particles with 1-4 μm in thickness and 4-15 μm in length was observed. EDX results showed that the atomic ratio of Ti:Si:C of grains is close to 3:1:2, which agrees with Ti₃SiC₂ composition.     

Effect of the SiO2/TiO2 ratio on the solid acidity of SiO2-TiO2/montmorillonite composites

SiO₂-TiO₂/montmorillonite composites with varying SiO₂/TiO₂ molar ratios were synthesized and the effect of the SiO₂/TiO₂ ratio on the solid acidity of the resulting composites was investigated. Four composites with SiO₂/TiO₂ molar ratios of 0, 0.1, 1 and 10 were synthesized by the reaction of colloidal SiO₂-TiO₂ particles prepared from alkoxides with sodium-montmorillonite at room temperature. The composites showed slight expansion and broadening of the XRD basal reflection, corresponding to the intercalation of fine colloidal SiO₂-TiO₂ particles into the montmorillonite sheets and incomplete intercalation to form disordered stacking of exfoliated montmorillonite and colloidal SiO₂-TiO₂ particles. The colloidal particles crystallized to anatase in the low SiO₂/TiO₂ composites but remained amorphous in the high SiO₂/TiO₂ composites. The specific surface areas (S_BET) of the composites measured by N₂ adsorption ranged from 250 to 370 m²/g, considerably greater than in montmorillonite (6 m²/g). The pore size increased with decreasing SiO₂/TiO₂ molar ratio of the composites. The NH₃-TPD spectra of the composites consisted of overlapping peaks, corresponded to temperatures of about 190 and 290 °C. The amounts of solid acid obtained from NH₃-TPD were 186-338 μmol/g in the composites; these values are higher than in the commercial catalyst K10 (85 μmol/g), which is synthesized by acid-treatment of montmorillonite. The present sample with SiO₂/TiO₂ = 0.1 showed the highest amount of acid, about four times higher than K10.     

The production of grain oriented lanthanum titanate (La2Ti2O7) ceramics by uniaxial hot-forging process for improved fracture toughness

The layered-structural ceramics, such as lanthanum titanate (La₂Ti₂O₇), have been known for their good electrical and optical properties at high frequencies and temperatures. However, few studies have been conducted on the mechanical properties of these ceramics. The interest in ceramic hot-forging (HF) has been greatly increased recently due to the enhancement in fracture toughness via bridging effect of oriented grains. In this study, grain oriented lanthanum titanate was produced by the hot-forging process. The characterizations of the samples were achieved by density measurement, scanning electron microscopy (SEM), optical microscopy, X-ray diffraction (XRD), Vickers indentation and three-point bending test. According to X-ray diffraction patterns, the orientation factor (f) was found to be 0.73 for certain hot-forging conditions resulting an improved fracture toughness. The improved fracture toughness of La₂Ti₂O₇ (3.2 MPa m^1/2) reached to the value of monolithic alumina (Al₂O₃) between 3 and 4 MPa m^1/2.     

Dielectric and pyroelectric anisotropy in melt-quenched BaBi2(Nb1 − xVx)2O9 ceramics

The (0 0 l) textured BaBi₂(Nb_1 − xV_x)₂O₉ (where x = 0, 0.03, 0.07, 0.1 and 0.13) ceramics were fabricated via the conventional melt-quenching technique followed by high temperature heat-treatment (800-1000 °C range). The influence of vanadium content and sintering temperature on the texture development and relative density were investigated. The samples corresponding to the composition x = 0.1 sintered at 1000 °C for 10 h exhibited the maximum orientation of about 67%. The Scanning electron microscopic studies revealed the presence of platy grains having the a-b planes perpendicular the pressing axis. The dielectric constant and the pyroelectric co-efficient values in the direction perpendicular to the pressing axis were higher. The anisotropy in the dielectric constant is about 100 (at 100 kHz) at the dielectric maximum temperature and anisotropy in the pyroelectric co-efficient is about 50 μC cm⁻² °C⁻¹ in the vicinity of pyroelectric anomaly for the sample corresponding to the composition x = 0.1 sintered at 1000 °C. Higher values of the dielectric loss and electrical conductivity were observed in the direction perpendicular to the pressing axis which is attributed to the high oxygen ion conduction in the a-b planes.     

A powder X-ray diffraction refinement of the BaNd2Ti3O10 structure

The structure parameters of BaNd₂Ti₃O₁₀ were refined based on Olsen’s model. This material has a monoclinic unit cell with space group P2₁/m. The unit cell parameters are: a=7.73030(14) Å, b=7.62578(14) Å, c=14.23174(31) Å, β=97.832(6)°. The structure can be considered as a layered perovskite-like structure, in which the perovskite block shows distortion. The various layers link in the order of (Ba_1/2O)-(Ba_1/2TiO₃)-(NdTiO₃)-(NdTiO₃).     

无压烧结合成纯Ti3SiC2及其晶体生长机理

在1400℃,用Ti,Si,C,Al,NaCl原料,氩气保护下无压烧结合成出纯净的、层状的Ti3SiC2陶瓷。用X射线衍射、扫描电子显微镜,透射电子显微镜对Ti3SiC2陶瓷的物相、表面形貌、微观结构进行表征。对合成出的Ti3SiC2陶瓷的微观形貌进行观察,发现Ti3SiC2晶体中有规整的六方形状的层状晶体,提出了Ti3SiC2晶体的自由生长的机理。Ti3SiC2晶体的生长机理由二维成核理论控制,台阶状晶体生长的形貌表明(002)晶面的生长要经过两个独立的过程。添加NaCl,有助于生成高纯度的层状Ti3SiC2陶瓷。     

New substitutions and novel derivatives of the Aurivillius phases, Bi5TiNbWO15 and Bi4Ti3O12

We investigated isomorphous substitution of several metal atoms in the Aurivillius structures, Bi₅TiNbWO₁₅ and Bi₄Ti₃O₁₂, in an effort to understand structure-property correlations. Our investigations have led to the synthesis of new derivatives, Bi₄LnTiMWO₁₅ (Ln = La, Pr; M = Nb, Ta), as well as Bi₄PbNb₂WO₁₅ and Bi₃LaPbNb₂WO₁₅, that largely retain the Aurivillius (n = 1) + (n = 2) intergrowth structure of the parent oxide Bi₅TiNbWO₁₅, but characteristically tend toward a centrosymmetric/tetragonal structure for the Ln-substituted derivatives. On the other hand, coupled substitution, 2Ti^IV → M^V + Fe^III in Bi₄Ti₃O₁₂, yields new Aurivillius phases, Bi₄Ti_3−2xNb_xFe_xO₁₂ (x = 0.25, 0.50) and Bi₄Ti_3−2xTa_xFe_xO₁₂ (x = 0.25) that retain the orthorhombic noncentrosymmetric structure of the parent Bi₄Ti₃O₁₂. Two new members of this family, Bi₂Sr₂Nb₂RuO₁₂ and Bi₂SrNaNb₂RuO₁₂ that are analogous to Bi₂Sr₂Nb₂TiO₁₂, possessing tetragonal (I4/mmm) Aurivillius structure have also been synthesized.     

Reinvestigation of the binary diagram Na3PO4-FePO4 and crystal structure of a new iron phosphate Na3Fe3(PO4)4

A new iron(III) phosphate Na₃Fe₃(PO₄)₄ has been synthesized and characterized. It decomposes before melting at 860°C into FePO₄ and Na₃Fe₂(PO₄)₃. The structure of the compound was determined by single-crystal X-ray diffraction. The unit cell is monoclinic with the following parameters: a=19.601(8) Å, b=6.387(1) Å, c=10.575(6) Å and β=91.81(4)°; Z=4; space group: C2/c. Na₃Fe₃(PO₄)₄ exhibits a layered structure involving corner-linkage between FeO₆ octahedra, and corner- and edge-sharing between FeO₆ octahedra and PO₄ tetrahedra. The Na⁺ cations occupying the interlayer space are six- and seven-fold coordinated by oxygen atoms. The relationship between the structure of Na₃Fe₃(PO₄)₄ and the previous reported hydrate K₃Fe₃(PO₄)₄·H₂O will be discussed.     

Characterization of nanosized Al2(WO4)3

Nanosized aluminum tungstate Al₂(WO₄)₃ was prepared by co-precipitation reaction between Na₂WO₄ and Al(NO₃)₃ aqueous solutions. The powder size and shape, as well as size distribution are estimated after different conditions of powder preparation. The purity of the final product was investigated by XRD and DTA analyses, using the single crystal powder as reference. Between the specimen and the reference no difference was detected. The crystal structure of Al₂(WO₄)₃ nanosized powder was confirmed by TEM (SAED, HRTEM). In additional, TEM locality allows to detect some W₅O₁₄ impurities, which are not visible by conventional X-ray powder diffraction and thermal analyses.     

Tunable and microwave dielectric properties of Ba0.5Sr0.5TiO3-BaWO4 composite ceramics doped with Co2O3

Co₂O₃ doped BaWO₄-Ba_0.5Sr_0.5TiO₃ composite ceramics, prepared by solid-state route, were characterized systematically, in terms of their phase compositions, microstructure and microwave dielectric properties. Doping of Co₂O₃ promoted grain growth, reduced Curie temperature and broadened phase-transition temperature range of BaWO₄-Ba_0.5Sr_0.5TiO₃, which were attributed mainly to the substitution of Co³⁺ for Ti⁴⁺ at B site in the perovskite lattice. Dielectric diffusion behaviors of the composite ceramics were discussed. The composite ceramics all had dielectric tunability of higher than 10% at 30 kV/cm and 10 kHz, with promising microwave dielectric properties. Specifically, the sample doped with 0.2 wt.% Co₂O₃ exhibited a tunability of 20%, permittivity of 225 and Q of 292 (at 1.986 GHz), making it a suitable candidate for applications in electrically tunable microwave devices.     

Fabrication of TiO2 hollow fibers with surface nanostructure

Polyvinyl alcohol-TiO₂ (PVA-TiO₂) core sheath nanofibers were fabricated by electrospinning an aqueous solution of PVA and introducing the thread-like droplets directly into a titanium tetraisopropoxide (TTIP)/hexane solution. Rod-like and sheet-like structures of lepidocrocite-type layered titanate formed on the surface of the TiO₂ sheath of the nanofibers by alkaline treatment in 1 mol L⁻¹ aqueous NaOH solution at 363 K. The nanofibers were converted to hollow TiO₂ nanofibers with surface nanostructure and anatase crystallinity by acid treatment to remove sodium ions and heat treatment at 773 K. The surface nanostructures enhanced the crystallinity and external surface area of the nanofiber and contributed to the improvement of photocatalytic oxidation activity.     

Synthesis, structure, and electrochemical characteristics of LiNi1/3Co1/3Mn1/3O2 prepared by thermal polymerization

A thermal polymerization route was adopted to synthesize layered LiNi_1/3Co_1/3Mn_1/3O₂ materials. After annealing the polymer gel containing metal salts at different temperatures from 850 to 1000 °C for different time between 6 and 25 h, powders of pure α-NaFeO₂ phase were obtained. The crystal structure, morphology and electrochemical properties of the products were investigated by XRD, SEM, electrochemical cell cycling and AC impedance spectroscopy. It is found that the powder annealed at 950 °C for 15 h shows the best electrochemical property with the first specific discharge capacity of 188 mAh/g at C/10 and 87% retention after 100 cycles. It exhibits good rate capability with the specific capacity of 169 mAh/g at 1 C and 110 mAh/g at 6 C. Adopting a slowly cooling procedure during the powder annealing can improve the electrochemical performance of the LiNi_1/3Co_1/3Mn_1/3O₂ powder.     

Formation of SrTiO3 from Sr-oxalate and TiO2

SrTiO₃ powder has been prepared from Sr-oxalate and TiO₂ precursors, instead of using titanyl-oxalate. Sr-oxalate was precipitated from nitrate solution onto the surface of suspended TiO₂ powders. Crystallization of SrTiO₃ from the precursor was investigated by TGA, DTA and XRD analysis. It is evident that precursor, upon heating, dehydrates in two stages, may be due to the presence of two different types of Sr-oxalate hydrates. Dehydrated precursor then decomposes into SrCO₃ and TiO₂ mixture. Decomposition of SrCO₃ and simultaneous SrTiO₃ formation occur at much lower temperature, from 800 °C onwards, due to the fine particle size of the SrCO₃ and presence of acidic TiO₂ in the mixture. The precursor completely transforms into SrTiO₃ at 1100 °C. About 90 nm size SrTiO₃ crystallites are produced at 1100 °C/1 h, due to the lower calcination temperature and better homogeneity of the precursor.     

Synthesis, characterization and electrical properties of quaternary selenodiphosphates: AMP2SE6 with A = Cu, Ag and M = Bi, Sb

The new quaternary selenophosphate phases AMP₂Se₆ (A=Cu, Ag and M=Bi, Sb) were synthesized by ceramic methods at 1023 K. These phases were characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray analysis (EDX) and a.c. and d.c. electrical conductivity measurements. The phases all show values of electrical conductivity, σ, of about 10⁻⁴ Ω⁻¹ cm⁻¹ at 303 K and photoconductive effect. The conductivity is nearly five orders of magnitude larger than that of related phases.     

Study on properties of BaxSmyTi7O20 ceramics with CaO-SiO2-B2O3 glass

The effect of CaO-SiO₂-B₂O₃ (CSB) glass addition on the sintering temperature and dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics has been investigated using X-ray diffraction, scanning electron microscopy and differential thermal analysis. The CSB glass starts to melt at about 970 °C, and a small amount of CSB glass addition to Ba_xSm_yTi₇O₂₀ ceramics can greatly decrease the sintering temperature from about 1350 to about 1260 °C, which is attributed to the formation of liquid phase. It is found that the dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics are dependent on the amount of CSB glass and the microstructures of sintered samples. The product with 5 wt% CSB glass sintered at 1260 °C is optimal in these samples based on the microstructure and the properties of sintering product, when the major phases of this material are BaSm₂Ti₄O₁₂ and BaTi₄O₉. The material possesses excellent dielectric properties: ?_r = 61, tan δ = 1.5 × 10⁻⁴ at 10 GHz, temperature coefficient of dielectric constant is −75 × 10⁻⁶ °C⁻¹.     

High rate performances of the cathode material LiNi1/3Co1/3Mn1/3O2 synthesized using low temperature hydroxide precipitation

A low-temperature reaction route is introduced based on hydroxide precipitation method to synthesize the cathode material LiNi_1/3Co_1/3Mn_1/3O₂. The crystal structure and morphology of the prepared powder have been characterized by X-ray diffraction and Scan electron microscope, respectively. The charge–discharge tests were performed between 2.5 and 4.5 V. The discharge capacity of the material is strongly impacted by the reaction temperature. The powders sintered at 850 °C show the best electrochemical performance and the initial discharge capacity is about 160 mAh g⁻¹ at 5 C. Powder X-ray diffraction and Scan electron microscope results reveal that the excellent electrochemical performances should be ascribed to the lower precursor reaction temperature, the lower degree of cation mixing and analogous spherical small particles, which can improve the transfer of Li ions and electrons. All these results indicate that this material has potential application in lithium-ion batteries.     

Insertion of trivalent cations in the layered MPS3 (Mn, Cd) materials

The Al_0.21Mn_0.78PS₃, Al_0.15Cd_0.83PS₃, In_0.20Cd_0.70PS₃ and Ga_0.28Cd_0.58PS₃ compounds have been synthesized by the cation-exchange process used for other cationic species of the same family. These compounds were characterized by X-ray diffraction , Fourier transform infrared spectroscopy, ICP plasma analyses, photoconductivity and electrochemical impedance spectroscopy. The compounds synthesized show electrical conductivities (σ) of the order of 10⁻⁹ to 10⁻¹⁰ S cm⁻¹ at 298 K and photoconductive effect. The physical properties of the new Al³⁺ materials reveal the same behavior as our previous report on In³⁺ and Ga³⁺ compounds.