Vertical crack distribution effect on the TBC delamination induced by crack growth from the ceramic surface and near the interface

The propagation of vertical crack on the surface of thermal barrier coatings (TBCs) may affect the interface cracking and local spallation. This research aims to establish a TBC model incorporating multiple cracks to comprehensively understand the effects of vertical crack distribution on the coating failure. The continuous TGO growth and ceramic sintering are together introduced in this model. The influence of the vertical crack spacing and non-uniform distribution on the stress state, crack driving force, and dynamic propagation is examined. Moreover, the influence of coating thickness on the crack growth driving is also explored. The results show that large spacing will lead to early crack propagation. The uniform distribution of vertical cracks can delay the spallation. When the spacing is less than 4 times ceramic coat thickness, the cracking driving force will come in a steady-state stage with the increase of vertical crack length. Prefabrication of vertical cracks with spacing less than 0.72 mm on the coating surface can greatly decrease the strain energy. The results in this study will contribute to the construction of an advanced TBC system with long lifetime.     

Comprehensive dynamic failure mechanism of thermal barrier coatings based on a novel crack propagation and TGO growth coupling model

Comprehensive understanding of failure mechanism of thermal barrier coatings (TBCs) is essential to develop the next generation advanced TBCs with longer lifetime. In this study, a novel numerical model coupling crack propagation and thermally grown oxide (TGO) growth is developed. The residual stresses induced in the top coat (TC) and in the TGO are calculated during thermal cycling. The stresses in the TC are used to calculate strain energy release rates (SERRs) for in-plane cracking above the valley of undulation. The overall dynamic failure process, including successive crack propagation, coalescence and spalling, is examined using extended finite element method (XFEM). The results show that the tensile stress in the TC increases continuously with an increase in an undulation amplitude. The SERRs for TC cracks accumulate with cycling, resulting in the propagation of crack toward the TC/TGO interface. The TGO cracks nucleate at the peak of the TGO/bond coat (BC) interface and propagate toward the flank region of the TC/TGO interface. Both TC cracks and TGO cracks successively propagate and finally linkup leading to coating spallation. The propagation and coalescence behavior of cracks predicted by this model are in accordance with the experiment observations. Therefore, this study proposed coating optimization methods towards advanced TBCs with prolonged thermal cyclic lifetime.     

Evaluation of stress distribution and failure mechanism in lanthanum–titanium–aluminum oxides thermal barrier coatings

LaTi₂Al₉O₁₉ (LTA) is one of the most promising materials for new thermal barrier coatings (TBCs) to fulfill the demand of advanced gas turbines owing to its high temperature stability and low thermal conductivity. In the present study, a finite element (FE) based numerical study has been carried out to investigate the stress distribution in LTA single layered coating system in comparison with traditional yttria stabilized zirconia (YSZ) TBC. Stresses in YSZ/LTA double ceramic layer TBC system are also determined and presented for comparative analysis. The thermal cycling effect is simulated by sequent increment in TGO thickness in a series of FE simulations. In-plane stresses (σ_xx), out-of-plane stresses (σ_yy) and shear stresses (σ_xy) are determined for all systems, and peak stress values are presented for quantitative comparison. Elastic strain energy stored in TGO of all systems is calculated from FE results for TBC structural integrity assessment. It has been found that maximum in-plane and shear stresses are lower in the double ceramic layer coating system than in the single layer ceramic coating system. However, peak axial tensile and compressive stresses in the double ceramic layer coating are very close or higher than those in the single layer topcoat. Calculation of elastic store energy shows that double ceramic layer TBC system may exhibit better stability as compared to single layer systems. Results are presented to explain the failure mechanism in LTA coatings.     

Numerical study of residual stresses in environmental barrier coatings with random rough geometry interfaces

To clarify the role of the coating interface geometry and thermally grown oxide (TGO) layer in the failure of environmental barrier coatings (EBCs) and to further understand the cracking and spalling mechanisms of coatings, in this study, the thermomechanical properties of the multilayer coating system (Yb₂SiO₅/Yb₂Si₂O₇/Si), the morphology of the coating interface and the influence of the oxide layer on the local stresses during cooling were considered based on a random rough interface geometry model. The results showed that the rough geometry increased the magnitude of residual stresses at the interface and that the stress distribution away from the interface was less affected than the coating without roughness. The cracks on the outer surface of the Yb₂SiO₅ layer initiate in the valley region and spread with a stress value independent of the TGO thickness, and this failure may occur by cracking under tensile stress. The overall stress intensity at the TOP/EBC interface was lower than that at the upper surface of the TOP layer. The presence of TGO increased the magnitude of residual stresses in the BC and EBC layers, which caused cracks at the TGO/BC and TGO/EBC interfaces to occur at opposite locations. The phase change of the TGO layer from β-cristobalite to α-cristobalite cause a rapid increase in the overall level of coating stress, which may be a direct factor in coating failure. The calculation results provide a theoretical basis for the coating design and manufacturing process.     

The sintering behavior of plasma-sprayed YSZ coating over the delamination crack in low temperature environment

The sintering behavior of plasma-sprayed yttria-stabilized zirconia (YSZ) coating over the delamination crack and its influence on YSZ cracking were investigated via gradient thermal cycling test and finite element model (FEM). The gradient thermal cycling test was performed at a peak surface temperature of 1150 °C with a duration of 240 s for each cycle. A three-dimensional model including delamination cracks with different lengths was employed to elaborate the temperature evolution characteristics in YSZ coating over the delamination cracks. The temperature over the delamination crack increases linearly with the crack propagation, which continuously promotes the sintering of YSZ coating in the region. As a result, the YSZ coating over the delamination crack sinters dramatically despite of the low temperature exposure. Meanwhile, the temperature distribution difference in YSZ coating induces an nonuniform sintering along both free surface and thickness of YSZ coating. Correspondingly, the maximum vertical crack driving force locates at the YSZ free surface over the delamination crack center, which makes the vertical cracks generate in this region and propagate to the interface of YSZ /bond coat with YSZ further sintering. The vertical crack promotes the delamination crack propagation via accelerating the oxidation velocity of the bond coat. The influence of temperature rise on delamination crack propagation can be divided into two stages: the little contribution stage and the promotion stage. For the actual engine exposure to low temperature, the study of phase transformation of YSZ over the delamination crack is indeed needed because of an extended remarkable temperature rise period.     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Residual stress distribution along interfaces in thermal barrier coating system under thermal cycles

The residual interfacial stress plays an important role in crack initiating and propagating along the interface, which could result in delamination failure of the thermal barrier coatings (TBCs). In this study, the finite element model of air plasma spraying(APS) TBCs was established to assess the level and distribution of residual stress along top coat(TC)/thermally grown oxide (TGO) and bond coat (BC)/TGO interfaces under thermal cycles. Instead of using vertical stress S₂₂ in global coordinate system, the normal and tangential components in the local system along the interfaces, transformed from stress components S₁₁, S₂₂, and S₁₂ in the global one, were used to evaluate the way the cracks initiate and propagate along the interfaces. Firstly, the effect of the number of thermal cycles on residual stress was investigated. It was found that, for the TBCs model without TGO growth and crack, the impact of the number of thermal cycles on the stress is very insignificant and could be ignored. So the present study only chose to focus on the first thermal cycle. Then the influence of the TGO thickness and the interface amplitude on the normal and tangential residual stresses for both homogeneous and inhomogeneous temperature fields was explored. The results show that the TGO thickness, interface amplitude and temperature field affect the residual stress level and distribution, leading to different fracture mechanisms along TC/TGO and TGO/BC interfaces. Finally, the difference between the vertical stress in the global coordinate system and the normal stress in the local coordinate system was studied. Compared with vertical stress S₂₂, the stress components normal and tangential to the TC/TGO and TGO/BC interfaces are more appropriate to describing the stress distribution along the interfaces and predicting the propensity of crack initiating and propagating along the interfaces.     

Effect of sintering temperature on the microstructure and performance of a ceramic coating obtained by the slurry method

In this paper, SiO₂, Cr₂O₃, Al₂O₃, and MgO were used as ceramic aggregates, and a small amount of Al powder was added. A ceramic coating was prepared on a Q235 steel substrate. The effect of the sintering temperature on the coating microstructure, phase structure and wear resistance was studied by Scanning Electron Microscope (SEM), X-ray Diffraction (XRD) and friction and wear testing. The results show that the tensile strength of the ceramic coating is increased after sintering, the structure becomes dense, and the size of coated micropores is increased to release the internal tensile stress. With the increase of the sintering temperature and tensile stress, the micropores begin to release the excess tensile stress in the form of crack initiation and expansion. The mineralization of MgO, Cr₂O₃, nMgO and mSiO₂ phases can be achieved by sintering the coating at 200?°C; the oxygen in the atmosphere migrates along the micropores in the coating to react with Fe in the steel substrate, forming FeO, and the resulting FeO reacts with the SiO₂ in the coating to form the Fe₂SiO₄ phase. The coating has the best wear resistance after being sintered at 400?°C, and the abrasion resistance of the sample is 6.7 times higher than that of the sample dried at room temperature.     

High temperature creep and tensile properties of alumina formed on Fecralloy foils doped with yttrium

The three batches of Fecralloy foils, which differ from each other in contents of yttrium, that is, 10, 280 and 560 ppm, respectively, were chosen as the thermally grown oxide (TGO), alumina (α-Al₂O₃) forming substrate. The creep tests were performed with the Fecralloy foils, which have the α-Al₂O₃ TGO of 0–4 μm thickness, on the surfaces. The creep rates decreased as the TGO thickness increased. The yttrium content above 280 ppm delayed the creep rate of the Fecralloy substrate. The higher creep rate than that of the stand-alone polycrystalline alumina and the dependency of the creep rate on TGO thickness agrees with the hypothesis that the high temperature creep of the TGO is a consequence of the inter-grain growth of the TGO. The yttrium content of lower than 560 ppm did not affect on the creep rate of TGO. Tensile tests were performed with the same alloys, which have the α-Al₂O₃ TGO of 0–3 μm thickness. The tensile strength of the substrate itself increased with Y content by ～20%. The tensile stress of the α-Al₂O₃ TGO decreased with Y-content but it is almost constant, regardless of the TGO thickness. The peak stresses were found at the strain range of ? = 0.7–1.5%, regardless of the TGO thickness, and the batches, thereafter, the parallel cracks perpendicular to the loading direction, formed on the surface. The obtained stress–strain curves of TGO fluctuated. It showed a common feature, that is, a sharp stress drop after the initial yield point at σ_Y = 40–85 MPa, but the stress increased again until the peak points, σ_UTS = 50–110 MPa.     

Thermal cycling behavior of EB-PVD rare earth oxides co-doping ZrO2-based thermal barrier coatings

Novel ceramic topcoat of Gd₂O₃–Yb₂O₃–Y₂O₃ co-stabilized ZrO₂ (GYbYSZ) thermal barrier coatings were fabricated via EB-PVD technique. The phase structural stability, phase constituent, chemical composition, morphology and cyclic oxidation of the thermal barrier coatings (TBCs) were systematically studied. Based on the XRD results, the GYbYSZ ceramics has not undergone phase transformation upon long-term annealing at 1373 K and 1523 K. Although the chemical content of the GYbYSZ ceramic coat deviates from the stoichiometric value, the coating is mostly composed of cubic phase, which is accord with the XRD pattern of the original ingot. A pyramidal-like morphology appears in the microtexture of the column tips and the measured diameters of the pyramids are about 2.5~4 μm. After thermal cycling, the surface of the coating presents a multi-layer structure, which is followed by layer-by-layer spallation. The failure zone of the ceramic coats is possible to occur the interior of the thermally grown oxide (TGO) layer, or within the top ceramic coat at the interface of bond coat/TGO layers. The degradation of GYbYSZ TBCs is primarily attributed to the accumulation and relaxation of residual stress, propagation of vertical through microcracks, the growth rumpling of TGO layer, the ridges of grain boundary and the abnormal oxidation of bond coat.     

Thermal cycling behavior of plasma-sprayed yttria-stabilized zirconia thermal barrier coating with La0.8Ba0.2TiO3−δ top layer

In this study, a La_0.8Ba_0.2TiO_3?δ (LBT) upper layer was deposited on an yttria-stabilized zirconia (YSZ) thermal barrier coating (TBC) through atmospheric plasma spraying. The thermal cycling behaviors of the YSZ single-ceramic-layer and LBT–YSZ double-ceramic-layer coatings at 1000 °C were investigated through a water quenching method. Moreover, phases, microstructural evolution, and elemental distributions were studied through by X-ray diffraction and scanning electron microscopy–energy-dispersive X-ray spectroscopy. The results showed that the thermal cycling lifetime of the LBT–YSZ coating was 27% higher than that of conventional YSZ coating. The conventional YSZ coating failed after 251 cycles because of the joining of the continuous horizontal and vertical cracks caused by the formation of thermal growth oxides and the bending effect of the single-ceramic-layer structure. The thermal cycling behavior of the LBT–YSZ coating was different from that of the YSZ coating at the edge and center. Although the former was similar to the failure behavior of the YSZ coating, the cracks in the vertical direction were deflected as a result of the bending effect of the double-ceramic-layer structure during quenching. This deflection led to the formation of slope cracks with longer propagation paths and slope spallation zones. The latter showed small-debris spallation on top of the LBT upper layer due to the lower fracture toughness of the LBT, which protected the central coating from the structural damage of the ceramic coating. These two behaviors would either release the thermal stress or increase the crack-propagation energy requirement in the ceramic coating, consequently improving the thermal cycling lifetime of the LBT–YSZ coating. In summary, depositing an LBT upper layer could potentially improve the thermal cycling lifetimes of TBCs.     

Stress states and crack behavior in plasma sprayed TBCs based on a novel lamellar structure model with real interface morphology

To ascertain the crack growth behavior and coalescence mechanism in thermal barrier coatings (TBCs) is beneficial for understanding the failure of TBCs and proposing the probable optimization methods. In this work, a novel lamellar structure model with real interface morphology is developed to explore the crack growth behavior and the failure mechanism of TBCs during thermal cycling. Three typical defects which include pore, inter-splat crack, and intra-splat are incorporated in the model. To simulate the oxidation process of the bond coat (BC) realistically, The oxidation growth process is simulated via changing the BC properties to thermally grown oxide (TGO) properties layer by layer. The effects of the lateral growth strain distribution through TGO thickness on the stress states are executed. Moreover, the influences of BC creep on the crack growth and coating lifetime are further elaborated. The results show that the larger the lateral growth strain gradient, the smaller the residual tensile stress. The irregular interface morphology results in the redistribution of residual stresses. Although the pores and cracks can alleviate the tensile stress near the valley, large stress concentration will occur near them. At the early phase of thermal cycling, the cracks grow steadily. After more cycles, the cracks propagate rapidly and merge with others. The simulated delamination path is in agreement with the experiment results. Not only does BC creep change the crack coalescence mechanism, it also decreases the thermal cyclic lifetime of TBCs. The coating optimization method proposed in this study provides another option for developing advanced TBCs with longer lifetime.     

On crack evolution with texturization of bonding layer in thermal barrier coating

The interface morphology of the bonding layer has a considerable effect on the damage and failure of sandwich-structured thermal barrier coatings. This work investigated the comprehensive effects of a grooved texture produced using laser ablation on the local surface strain, interfacial stress and strain, and crack behavior of the bonding layer in a thermal barrier coating system. The distribution and evolution of the local surface strain was obtained using the digital image correlation method. The interfacial stress, and the strain between the ceramic and bonding layers, were determined through a simulation of the plane-strain model, and the morphology and propagation of cracks were observed in thermal barrier coatings under an external tensile load. The results indicated that the local surface strain of the thermal barrier coating increased with the texturization of the bonding layer, whereas the fluctuation decreased. There were two inflection points in the local surface strain–time curves, corresponding to the initiation of surface cracks and that of interfacial transverse cracks. The surface cracks were initiated earlier than those without the texturization of the bonding layer. However, the behavior of the interfacial cracks was more complicated. If the roughness of the texture, defined as Rc, was small, the surface cracks propagated vertically to the interface between the ceramic and bonding layers, and turned into transverse cracks, leading to a separation of the ceramic layer. If Rc was greater than 22 μm, the surface cracks went further down to the interface between the bonding layer and substrate, and propagated horizontally, resulting in the separation of both the ceramic and bonding layers. Meanwhile, interfacial cracking and separation were deferred. A large roughness resulted in good cohesion between the ceramic and bonding layers, and a high stiffness for the coating, which improved the damage resistance and extended the life of the coating.     

Fabrication of ceramic sealing coatings for shell bionic structures and their failure mechanism during thermal cycling

The porous ceramic coating as a "brick" layer sprayed by air plasma spraying(APS) and MK resin as a "mud" layer prepared by a high viscosity spray gun were characterized and tested. Three specifications of the "brick-mud" layered ceramic sealing coating were fabricated through the cyclic and orderly deposition of the "brick" layer and "mud" layer, and the thermal cycling performance and failure mechanism of the three new coatings were studied. The results showed that the agglomerated Y₂O₃ partially stabilized ZrO₂ (YSZ) particles had porous spherical structures and good sprayability, and the content of the YSZ phase in the prepared "brick" layer was 54.2%. The "mud" layer had good phase stability and was amorphous SiO₂ at and below 1100 °C. The fracture toughness of the pure YSZ coating was 2.295 ± 0.135 MPa?m^0.5, and which of the “mud” layer was reduced by 72.3%. The thermal cycling life of the conventional coating was only 67.3 times, which of A1, A2 and A3 coatings with 2, 3 and 6 "mud" layers were increased by 32.4%, 124.8% and 88.3%, respectively. In the thermal cycling process, the "weak" layer in the "brick-mud" layered coating led to the redistribution of internal stress and reduced the stress concentration in the top coating (TC)/TGO interface. Moreover, the initiation of microcracks in the "weak" layer, along with the "crack branching" effect and the "crack deflection" effect during the crack propagation process, could consume partial internal stress. Thus, the crack growth rates in the TC coating/TGO interface of the A1, A2 and A3coatings were lower than that of the conventional coating due to the above stress release mechanisms. In addition, the thermal cycling lives of the three new coatings with 2, 3 and 6 "mud" layers were improved to different degrees because of different stress effects.     

Stress states in plasma-sprayed thermal barrier coatings upon temperature cycling: Combined effects of creep,plastic deformation,and TGO growth

To ascertain material parameter effects on the stress states is beneficial to comprehend the crack growth behavior and delamination mechanism in thermal barrier coatings (TBCs). In this work, numerical models are established to explore the combined effects of material parameters including creep, plastic deformation, and thermally grown oxide (TGO) growth on the stress states upon temperature cycling. For all layers, thermal-physical properties reliant on temperature are incorporated into the model. The process of bond coat (BC) oxidation, namely TGO growth, is materialized by changing material properties with cycles. Based on the principle of a single variable, the residual stress states are explored using many different material combinations. The results indicate that the tensile stress in the ceramic top coat (TC) decreases with the increase in the TGO lateral strain distribution gradient. Increasing the BC yield strength or decreasing the TGO growth stress can reduce the tensile stress in TC if there is no creep in the model. When BC yield strength is relatively high (≥150 MPa), BC creep will strengthen the TC tensile stress. TGO creep can decrease the tensile stress in TC irrespective of TGO growth stress and BC creep. When TGO creep rate is higher than 10B^tgo, an exceedingly small tensile stress can always be achieved. This work could provide significant theory direction for material selection and composition control towards advanced TBCs with prolonged lifetime.     

Crack development behavior in thermally sprayed anti-oxidation coating under repeated thermal-oxygen coupling environment

The crack development behavior in thermally sprayed anti-oxidation coating was investigated after long-term and short-term oxidation with repeated thermal cycles from 1500 °C to room temperature. According to the distribution characteristics, the formed cracks can be divided into three types: type-A cracks with multi-directional features, type-B cracks originated from the inner interface bulges and type-C cracks initiating at surface oxide layer. Based on the analytical math models (blunt crack model and interface roughness model), the maximum stress at different positions was evaluated from the perspective of inner interface roughness, uneven oxide film, original microcracks and gathering micropores. The original vertical type-A cracks are most dangerous due to the highest crack tip stress. However, the micropore distribution or appropriate interface may promote transformation of vertical type-A cracks to less dangerous horizontal type-A cracks. This study on crack development behavior provides a fundamental insight and further avenues to optimize the composition and structure of thermally sprayed ceramic coating.     

Cracking behavior and delamination mechanism of lamellar structured TBC with localized mixed oxides

Mixed oxide (MO) with localized growth feature and high growth rate remarkably affects the lifetime of thermal barrier coatings (TBCs), which indicates that clarifying the ceramic cracking mechanism induced by MO is critical for developing new coatings with high durability. Two kinds of TBC models involving spherical and layered mixed oxides are created to explore the influence of MO growth on the local stress state and crack evolution during thermal cycle. The growth of α-Al₂O₃ is also included in the model. The undulating interface between ceramic coat and bond coat is approximated using a cosine curve. Dynamic ceramic cracking is realized by a surface-based cohesive interaction. The ceramic delamination by simulation agrees with the experimental observation. The effects of MO coverage ratio and growth rate on the TBC failure are also discussed. The results show that the MO growth causes the local ceramic coat to bear the normal tensile stress. The failure mode of coating is turned from α-Al₂O₃ thickness control to MO growth control. Once the mixed oxide appears, local ceramic cracking is easy to occur. When multiple cracks connect, ceramic delamination happens. Suppressing MO formation or decreasing MO growth can evidently improve the coating durability. These results in this work can provide important theoretical guidance for the development of anti-cracking TBCs.     

Failure mechanism of a (Ni,Pt)Al/EB-PVD 8YSZ deposited on substrate with different curvature signs in thermal shock test

A thermal shock test was conducted on an 8 wt% Y₂O₃ stabilized ZrO₂ electron beam-physical vapor deposited (EB-PVD 8YSZ) thermal barrier coating with a (Ni, Pt)Al bond coating on the substrate with different curvature signs. The microstructural evolution and durability have been characterized. The microstructure of the top ceramic layer is strongly dependent on the substrate geometry. The results of the thermal shock test indicated that the sample with a positive curvature exhibits mixed mode spalling by the linking of cracks at TBC/TGO interface and TGO/BC interface. Spallation occurs primarily at the TGO/BC interface and inside the bond coats near to the surface of bond coats in planar samples. The spalling occurs principally at the TGO/BC interface in specimens with a negative curvature. The failure mechanism is elucidated integrate with stress analysis.     

Constrained sintering and cracking of air plasma sprayed thermal barrier coatings: Experimental observation and modeling

The development of vertical cracks in air plasma sprayed (APS) thermal barrier coatings (TBCs) during thermal cycling and constrained sintering under a temperature gradient is investigated. Microstructural analysis shows that the development of the vertical cracks is associated with multiple processes, including sintering during the hold period and cleavage during cooldown. Inspired by the experimental observations, an image-based sintering model is used to simulate the development of vertical cracks as the coating sinters while constrained by a substrate. The computational results show that microstructural imperfections can develop into vertical cracks, which then propagate toward the interface. A simple analytical model is presented for the threshold level of in-plane stress for the onset of propagation of a vertical crack during constrained sintering. By combining the results of these different modeling approaches, the cross-coupling of the material and geometric parameters, and how this determines the sintering response (microstructure evolution) and vertical crack formation is evaluated. In addition, the growth of vertical cracks by a cleavage mechanism during cooldown is examined and the coupling between sintering, cleavage crack growth, and TBC lifetime is explored.     

Oxidation behaviors and mechanisms of Yb2O3-doped silicon coatings fabricated by vacuum plasma spray

Environmental barrier coatings (EBCs) have been widely studied for the protection of ceramic matrix composites (CMCs). The phase transition of silica thermal growth oxide (TGO) has been proved to be an important factor for the durability of EBCs. Yb₂O₃ could react with SiO₂ TGO and form silicate which may improve the stability of TGO and prolong the service life of EBCs. In the present work, Si coatings doped with different contents of Yb₂O₃ were fabricated by vacuum plasma spray. The oxidation behaviors of the composite coatings were evaluated at 1350 °C and compared with the pure Si coating. The evolution of phase composition and microstructure of mixed thermal growth oxide (mTGO) was characterized in detail. The results showed that the newly formed oxidation product, namely Yb₂Si₂O₇, could reduce the vertical cracks in mTGO layer and the mTGO/coating interface cracks, leading to a better binding performance of the mTGO layer. The oxidation mechanisms of the Yb₂O₃-doped Si coatings were analyzed based on microstructure and phase composition observations.