Investigation of dielectric and piezoelectric properties in aliovalent Eu3+-modified Pb(Mg1/3Nb2/3)O3-PbTiO3 ceramics

Rare earth (Eu³⁺)-modified Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃ (PMN-PT) polycrystalline ferroelectric ceramics were fabricated by high-temperature solid-state sintering, the phase structure, dielectric and piezoelectric properties were investigated. Eu³⁺ addition was found to significantly improve dielectric and piezoelectric properties of PMN-PT, where the optimized properties were achieved for the composition of 2.5 mol%Eu: 0.72PMN-0.28PT, with the piezoelectric d₃₃ = 1420 pC/N, dielectric ε_r = 12 200 and electromechanical k₃₃ = 0.78, respectively. All these results indicate that the Eu³⁺-doped PMN-PT ceramics are promising candidates for high-performance room-temperature piezoelectric devices.     

Co-substituted CuO–ZrO2–Nb2O5 composite ceramics with low-temperature sintering and low-loss for high-performance patch antenna

In the field of microwave dielectric ceramics for patch antennas, it has always been a thorny issue to simultaneously satisfy high dielectric constant, low sintering temperature and low dielectric loss. Here, a CCZN (x = 0.04) composite ceramic with excellent microwave dielectric properties was developed. It can be found that an appropriate amount of Co²⁺ substitution can enhance the compactness, increase the dielectric constant (ε_r), reduce the dielectric loss (tanδ) and enhance the temperature coefficient (τ_f). The composite ceramic with excellent dielectric properties (ε_r = 22.6, Q × f = 37,624 GHz, τ_f = ?64.9 ppm/°C) shows good sintering compatibility with Ag. Based on this composite ceramic, a high-performance patch antenna was designed for Beidou satellite navigation system (BDS). It presents a small size of 30 × 30*3.8 mm³ and excellent radiation performance (return loss = ?32.9 dB, VSWR = 1.047, impedance bandwidth = 60.6 MHz, radiation efficiency = 94.6% and realized gain = 7.704 dB). This work promotes the application of microwave dielectric ceramics in the field of patch antennas.     

Improvement of the piezoelectric and ferroelectric properties of (K,Na)0.5NbO3 ceramics via two-step calcination–milling route

A second calcination–milling step was introduced in the conventional processing of (K, Na)_0.5NbO₃ (KNN) ceramics (sintered in air) to further homogenenize the particle size distribution of the pre-sintered powders. The ceramic derived from the powders prepared by the two-step route possesses grains with better uniformity and is more compact. The relative density of the bulk ceramic reached 96.9%. Excellent properties are obtained in as-prepared KNN ceramics with k_p=44%, d₃₃=111 pC/N, tanδ=0.85%, ε₃₃^T/ε_o=311, Q_m=193, P_r=25.4 μC/cm², d₃₃^⁎=251 pm/V, which are superior to those of the ceramics derived from the powders calcined once as used in the traditional processing. These results indicate that twice-calcination–milling route is shown to be a facile and effective way to simultaneously improve the piezoelectric and ferroelectric properties of KNN ceramics without sintering aids.     

CNT loaded PVDF-KNN nanocomposite films with enhanced piezoelectric properties

The emerging smart PVDF-based composites can compensate for the intrinsic property deficiencies in either of their components. The properties of the composite are determined by the properties of the constituents and its fabrication method. In this research, a lead-free piezoelectric ceramic, potassium sodium niobate (KNN), was used as the primary reinforcement, and MWCNTs were added to improve the electrical properties. Solution casting was used to prepare PVDF-KNN-CNT composite films. After phase and structure identification of composites using SEM, XRD, FTIR, and TGA methods, the dielectric, piezoelectric and ferroelectric properties of the products were investigated. The obtained results indicated a strong dependency of dielectric, piezoelectric, and ferroelectric properties of composites on KNN content. Samples with the highest KNN content rendered ε_r, d₃₃ and g₃₃ values of 156, 28 pC/N, and 20.32 mV m/N, respectively. Introducing a small amount of conductive CNT to primary PVDF-KNN composites can drastically affect the electrical properties by severely interfering in the charge distribution within the sample. While the dielectric constant was enhanced by increasing CNT content, both piezoelectric and ferroelectric properties showed their best behavior at a critical CNT loading. Beyond this limit, a percolation path formed, which is responsible for power consumption. At the optimum CNT amount, d₃₃ and g₃₃ reached 50 pC/N and 31.93 mV m/N, respectively. The presence of conducting CNTs gave rise to the formation of more round polarization curves with higher remnant polarization. The present findings give a prospective understanding of smart piezoelectric polymer-based composites that can be used as sensors and energy harvesters.     

Effect of BBS‐Based Frit on the Low Temperature Sintering and Electrical Properties of KNN Lead‐Free Piezoceramics

Using BaO–B₂O₃–SiO₂ (BBS)‐based frit as sintering aid, the K_0.49Na_0.51NbO₃ (KNN) + x wt% BBS (x = 1.0, 1.5, 2.0 and 2.5) lead‐free piezoelectric ceramics were successfully fabricated by solid‐state reaction method under low‐sintering temperature of 1000°C. The effect of BBS frit doping amount on the structure and electrical properties of the ceramics was investigated. The KNN ceramics with 1.5 wt% BBS frit showed optimal properties as follows: piezoelectric constant d₃₃ = 108 pC/N, planar electromechanical coupling coefficient k_p = 41%, mechanical quality factor Q_m = 225, relative dielectric constant ε_r = 410, dielectric loss tanδ = 0.57% and Curie temperature T_c = 400°C. This ceramic sample should be a good lead‐free candidate for actuators or high temperature sensors application due to its ultra‐low tanδ, relatively high Q_m and T_c.     

Effects of thickness on structures and electrical properties of K0.5Na0.5NbO3 thick films derived from polyvinylpyrrolidone-modified chemical solution

Lead-free ferroelectric K_0.5Na_0.5NbO₃ (KNN) films with different thicknesses were prepared by polyvinylpyrrolidone (PVP)-modified chemical solution deposition (CSD) method. The KNN films with thickness up to 4.9 μm were obtained by repeating deposition-heating process. All KNN thick films exhibit single perovskite phase and stronger (1 1 0) peak when annealed at 650 °C. The variation of dielectric constant with thickness indicates that there exists a critical thickness for the dielectric constant in the KNN films which should lie in 1.3–2.5 μm. The similar trend is observed for the ferroelectric and piezoelectric properties of KNN films. Both the remnant polarization P_r and the piezoelectric coefficient d₃₃ of KNN thick films increase with the film thickness and become saturated after the critical thickness.     

5G array antenna substrate for electromagnetic beam splitting via cobalt-substituted zinc molybdate low temperature co-fired ceramics

A novel Zn_1-xCo_xMoO₄ (ZCMO) (x = 0.03) ceramic with low-dielectric constant, low-loss, and low-sintering temperature for 5G electromagnetic beam splitting is developed by solid-state reaction method. This ceramic exhibits excellent microwave dielectric properties with ε_r = 8.0, Q × f = 57682 GHz, τ_f = ? 54.9 ppm/°C at a sintering temperature of 825 °C. An array antenna for electromagnetic beam splitting at 5.4 GHz is designed by using this ceramic for the first time. The highest efficiency and the best electromagnetic beam splitting effect can be jointly controlled by the dielectric constant and dielectric loss of the ceramic. The normalized reflection amplitude of each array unit cell is above 98 %, and the reflection phase covers 360°. The function of electromagnetic beam splitting is verified by the far-field pattern of the electric field. This work helps to promote the development of LTCC and broaden the application scope of microwave dielectric ceramics.     

Crystal structure,chemical bond characteristics,and microwave dielectric properties of novel Sr2CaMoO6 ceramic at different sintering temperatures

This work prepared a novel Sr₂CaMoO₆ (SCM) ceramic through the conventional solid-state process. The crystal structure, chemical bond characteristics, and microwave dielectric properties of SCM ceramic were investigated for the first time. The X-ray diffraction patterns and Rietveld refinement indicate that SCM ceramic formed an orthorhombic phase with the space group Pmm2 (25) at temperatures above 1300 °C. The lattice vibrational modes of SCM ceramic were obtained through the Fourier transformed infrared spectrum (FTIR). The measured dielectric constant and dielectric loss of SCM ceramic is close to the theoretical values obtained by FTIR. According to the P–V–L theory, the chemical bond characteristics of SCM ceramic were calculated. The high ionicity and lattice energy of the Mo–O bond positively affect the properties of SCM ceramic. The outstanding microwave dielectric properties of ε_r = 19.37, Q·f = 32,970 GHz (at 5.96 GHz), and τ_f = ?32.56 ppm/°C were obtained in SCM ceramic sintered at 1450 °C. This work reveals the crystal structure of SCM ceramic, establishes the relationship between the properties and chemical bonds of the ceramic, and lays a foundation for studying the dielectric properties of related ceramic systems.     

Fine-grained relaxor ferroelectric PMN-PT ceramics prepared using hot-press sintering method

Relaxor ferroelectric PbMg_1/3Nb_2/3O₃-PbTiO₃ (PMN-PT) ceramics are high-performance piezoelectric materials that are widely used in many electronic devices. However, it is extremely difficult to manufacture thin piezoelectric components dozens of micrometers in size using commercial coarse-grained PMN-PT ceramics. This limits the application of PMN-PT ceramics to high-frequency ultrasonic devices. In this work, we prepared a dense, fine-grained PMN-PT ceramic at low temperature using a hot-press sintering (HPS) method. The HPS ceramic had small grains with an average size of 1 μm and maintained high performance with a large permittivity (ε_r = 4500), piezoelectricity (d₃₃ = 650 pC/N), and electrostrain (S_E = 0.14% at 20 kV/cm). The large volume fraction of grain boundaries led to stronger relaxor behavior of the fine-grained PMN-PT ceramic than of the normal coarse-grained one. Owing to its small grains and high piezoelectric performance, this fine-grained PMN-PT ceramic meets the strict requirements of manufacturing thin piezoelectric components. Our results demonstrate that PMN-PT ceramics have great potential for developing low-cost, high-frequency ultrasonic devices by replacing expensive piezoelectric single crystals.     

Pyroelectric,ferroelectric, piezoelectric and dielectric properties of Na0.5Bi0.5TiO3 ceramic prepared by sol-gel method

Sodium bismuth titanate (BNT) nanopowder of molar composition 50/50 (Na_0.5Bi_0.5TiO₃) was prepared by a sol-gel processing method. The structure and microstructure of the precursor gel as well as the ferroelectric, pyroelectric, dielectric and piezoelectric properties of the BNT were studied. BNT crystallized in the rhombohedra perovskites structure Na_0.5Bi_0.5TiO₃ was obtained from the precursor gel by heating at 700 °C for 2 h in air. The BNT ceramic at 1100 °C sintering temperature present high crystallinity, good dielectric properties at 1 kHz (ε′=885, tan δ=0.03, T_c=370 °C), piezoelectric properties (k₃₃=0.39, c₃₃=105 GPa, e₃₃=12.6 C/m², d₃₃=120 pC/N), high remnant polarization (P_r=47 μC/cm²) and pyroelectric coefficient ($p$=707 μC/m² K) and low coercive field (E_c=55 kV/cm). Hence, the BNT prepared by sol-gel method could be used for silicon based memory device application where a low synthesis temperature is a key requirement.     

Enhanced Curie temperature and superior temperature stability by site selected doping in BCZT based lead-free ceramics

In this work, Bi³⁺ doped Ba_0.98-3x/2Bi_xCa_0.02Zr_0.02Ti_0.976Cu_0.008O₃ [0 ≤ x ≤ 0.03] lead free ceramics, to be employed for structural, dielectric and ferroelectric studies, have been synthesized via conventional solid state reaction method. Rietveld refinement of the X-ray diffraction (XRD) data evidences the existence of a pure perovskite phase with tetragonal symmetry for all ceramics. The Scanning Electron Microscopy (SEM) reveals that the grain size, which is 16.14 μm for x = 0 reduced to 2.11 μm for x = 0.03. Dielectric studies demonstrate excellent dielectric behavior with high Curie temperature (T_C ～159 °C), high dielectric constant (ε_r ～834, ε_max ～ 3146), and a low dielectric loss (tanδ ～ 0.019), for an optimum value of x = 0.02. The analysis of temperature coefficient of the dielectric permittivity indicates the applicability of these materials in multilayer ceramic capacitors. Impedance studies, conducted to understand the underlying physical mechanisms, are found to be in good agreement with the results of structural and dielectric studies. Furthermore, the ferroelectric measurement confirms the ferroelectric nature for all samples with an energy storage efficiency (η) of ～42% for x = 0.02 composition.     

Microwave dielectric properties of Ca1.15RE0.85Al0.85Ti0.15O4 (RE=Nd,La, Y) ceramics prepared by the reaction sintering method

Ca_1.15RE_0.85Al_0.85Ti_0.15O₄ (RE = Nd, La, Y) ceramics were prepared by a reaction sintering method. The sintering behavior, phase composition, microstructure and microwave dielectric performances of ceramics were investigated. X-ray diffraction patterns illustrated that both the Ca_1.15Nd_0.85Al_0.85Ti_0.15O₄(CNAT) and Ca_1.15Y_0.85Al_0.85Ti_0.15O₄(CYAT) ceramics are single-phase structures, and the Ca_1.15La_0.85Al_0.85Ti_0.15O₄(CLAT) ceramic contain LaAlO₃ and CaO phases. The apparent morphology and elemental distribution of the ceramic samples were analyzed by using scanning electron microscope and energy dispersive spectrometer. When the sintering temperature is 1500 °C, the CNAT and CYAT ceramics have the best microwave dielectric properties with ε_r = 19.2, Q × f = 74924 GHz, τ_f = ?1.21 ppm/°C and ε_r = 17.5, Q × f = 27440 GHz, τ_f = ?5.79 ppm/°C, respectively. And the best microwave dielectric properties of ε_r = 17.5, Q × f = 22568 GHz, τ_f = ?14.69 ppm/°C were obtained for the CLAT ceramic sintered at 1525 °C. The reaction sintering method provides a low-cost, economical and straightforward method for the preparation of the Ca_1.15RE_0.85Al_0.85Ti_0.15O₄ (RE = Nd, La, Y) ceramics, which has promising potential for application.     

The unusual case of plastic deformation and high dislocation densities with the cold sintering of the piezoelectric ceramic K0.5Na0.5NbO3

K_0.5Na_0.5NbO₃ (KNN) can be readily densified using the cold sintering process, but despite observing high relative permittivity, the ferroelectric hysteresis is strongly suppressed along with a major suppression in the all-important piezoelectric properties. In this study, KNN is fabricated using a NaOH+KOH transient flux under a uniaxial pressure of 400 MPa and heating to 300 °C for 2 h to drive densification to 93% theoretical. It is only after a secondary heat treatment that we observe improvements of the ferroelectric hysteresis and piezoelectric properties. From a detailed structural-property-processing study using analytical transmission electron microscopy (TEM), X-ray line broadening and high field dielectric characterization methodologies we conclude that there is an unusual in-situ plastic deformation process that takes place in addition to the densification under the cold sintering process. High densities of dislocations within grains were observed that lead to multiple pinning sites that impact both the intrinsic and extrinsic contributions to the high field dielectric and piezoelectric properties. Annealing significantly reduced the dislocation density in the highly defective crystallites, observed directly from the TEM and from the sharpening of the X-ray diffraction peaks, resulting in piezoelectric and ferroelectric properties that approached those of conventionally sintered KNN.     

Influence of cobalt and sintering temperature on structure and electrical properties of BaZr0.05Ti0.95O3 ceramics

Pure and Co-modified BaZr_0.05Ti_0.95O₃ ceramics were fabricated by the traditional solid state reaction technique. The influence of cobalt and sintering temperature on structure, dielectric, ferroelectric properties and diffuse phase transition of BZT ceramics were investigated systematically. 1300 °C was the optimal sintering temperature for BZT ceramics. The solid solubility limit of Co ions in BZT matrix was determined to be 0.4 mol%. The introduction of a moderate amount of Co ions was believed to benefit the microstructure development and make the grain size more uniform. Compared with undoped counterparts, 0.4 mol% Co-modified ceramics showed equivalent ferroelectric properties with a high remnant polarization (P_r=9.6 μC/cm²) and a low coercive field (E_c=0.21 kV/mm). Besides these, a relative high dielectric coefficient (ε_r=2030) and a low dielectric loss (tan δ=1.85%) were also obtained on this composition. The degree of diffuse phase transition was enhanced by the addition of Co ions. The related mechanism of the diffused phase transition behavior was discussed.     

Low-temperature sintering and electrical properties of (K,Na)NbO3 based lead-free ceramics with high Curie temperature

Lead-free ceramics (1 ? x)(K_0.48Na_0.52)NbO₃–(x/5.15)K_2.9Li_1.95Nb_5.15O_15.3 (x = 0.3–0.6, KNN–KLN100x) were prepared by conventional sintering technique at a low temperature of 960 °C. The effects of KLN contents on microstructure, dielectric, and piezoelectric properties were investigated. After the addition of KLN, the sintering performance and Curie temperature of the ceramics were markedly improved. The ceramics with x = 0.3 exhibited very good piezoelectric properties: d₃₃ = 138 pC/N, k_p = 45.03%, T_c = 495 °C, the dielectric constant at room temperature ?_r (RT) = 478 and the maximum dielectric constant ?_r (max) = 5067. These results indicated that the KNN–KLN100x lead-free ceramics sintered at low temperatures are promising for high temperature piezoelectric applications.     

Effects of sintering parameters and Nd doping on the microwave dielectric properties of Y2O3 ceramics

Y₂O₃ ceramics with good dielectric properties were prepared via co-precipitation reaction and subsequent sintering in a muffle furnace. The effects of Nd doping and sintering temperature on microwave dielectric properties were studied. With the increase in sintering temperature, the density, quality factor (Q×f), and dielectric constant (ε_r) values of pure Y₂O₃ ceramics increased to the maximum and then gradually decreased. The Y₂O₃ ceramics sintered at 1500 °C for 4 h showed optimal dielectric properties: ε_r=10.76, Q×f=82, 188 GHz, and τ_f=−54.4 ppm/°C. With the addition of Nd dopant, the Q×f values, ε_r, and τ_f of the Nd: Y₂O₃ ceramics apparently increased, but excessive amount degraded the quality factor. The Y₂O₃ ceramics with 2 at% Nd₂O₃ sintered at 1460 °C displayed good microwave dielectric properties: ε_r=10.4, Q×f=94, 149 GHz and τ_f=−46.2 ppm/°C.     

Influence of LNO Top Electrodes on Electrical Properties of KNN/LNO Thin Films Prepared by RF Magnetron Sputtering

Highly (001) oriented (K,Na)NbO₃ (KNN) lead‐free piezoelectric thin films were grown on LaNiO₃ (LNO)‐coated silicon by RF magnetron sputtering. The effects of the top electrodes on the electrical properties of KNN thin films were investigated. The dielectric and piezoelectric properties were remarkably improved in LNO/KNN/LNO (ε_r = 899 at 1 kHz, d₃₃ = 58 pm/V), compared with that in Pt/KNN/LNO (ε_r = 584 at 1 kHz, d₃₃ = 26 pm/V). An enhanced ferroelectricity was also obtained in LNO/KNN/LNO, with a remnant polarization of 12 μC/cm² and a maximum polarization of 23 μC/cm² at the applied field of 200 kV/cm. Besides, the temperature dependence of piezoelectricity of the films was characterized in this study.     

Improved sintering behavior and microwave dielectric properties of SnO2-based ceramics and their LTCC materials with ultrawide temperature stability

Microwave dielectric ceramics with simple composition, a low permittivity (ε_r), high quality factor (Q × f) and temperature stability, specifically in the ultrawide temperature range, are vital for millimetre-wave communication. Hence, in this study, the improvements in sintering behavior and microwave dielectric properties of the SnO₂ ceramic with a porous microstructure were investigated. The relative density of the Sn_1-xTi_xO₂ ceramic (65.1%) was improved to 98.8%, and the optimal sintering temperature of Sn_1-xTi_xO₂ ceramics reduced from 1525 °C to 1325 °C when Sn⁴⁺ was substituted with Ti⁴⁺. Furthermore, the ε_r of Sn_1-xTi_xO₂ (0 ≤ x ≤ 1.0) ceramics increased gradually with the rise in x, which can be ascribed to the increase in ionic polarisability and rattling effects of (Sn_1-xTi_x)⁴⁺. The intrinsic dielectric loss was mainly controlled by r_c (Sn/Ti–O), and the negative τ_f of the SnO₂ ceramic was optimised to near zero (x = 0.1) by the Ti⁴⁺ substitution for Sn⁴⁺. This study also explored the ideal microwave dielectric properties (ε_r = 13.7, Q × f = 40,700 GHz at 9.9 GHz, and τ_f = ?7.2 ppm/°C) of the Sn_0.9Ti_0.1O₂ ceramic. Its optimal sintering temperature was decreased to 950 °C when the sintering aids (ZnO–B₂O₃ glass and LiF) were introduced. The Sn_0.9Ti_0.1O₂-5 wt% LiF ceramic also exhibited excellent microwave dielectric properties (ε_r = 12.8, Q × f = 23,000 GHz at 10.5 GHz, and τ_f = ?17.1 ppm/°C). At the ultrawide temperature range (?150 °C to +125 °C), the τ_ε of the Sn_0.9Ti_0.1O₂-5 wt% LiF ceramic was +13.3 ppm/°C, indicating excellent temperature stability. The good chemical compatibility of the Sn_0.9Ti_0.1O₂-5 wt% LiF ceramic and the Ag electrode demonstrates their potential application for millimetre-wave communication.     

Enhanced structural,dielectric, ferroelectric,and piezoelectric properties of (1−x)Ba0.9Sr0.1TiO3–(x)Ba0.7Ca0.3TiO3 ceramics derived using mechano‐chemical activation technique

The effect of Ba_0.7Ca_0.3TiO₃ (BCT) substitution on the structural, dielectric, ferroelectric, and piezoelectric properties of mechano‐chemically synthesized lead‐free (1?x)Ba_0.9Sr_0.1TiO₃‐(x)Ba_0.7Ca_0.3TiO₃ (x=0.0, 0.10, 0.20, 0.35, and 0.50) ceramics have been investigated. XRD patterns confirms the formation of tetragonal phase with P4mm space group. The results indicate a strong influence of BCT substitution on the structural and electrical properties of Ba_0.9Sr_0.1TiO₃ (BST) ceramic. BST–BCT ceramic for x=0.35 have shown high dielectric constant ε_m~21 800, high remnant polarization P_r~10.16 μC/cm², large piezoelectric charge constant D₃₃~293 pC/N, large piezoelectric voltage constant g₃₃~5.80 mV·m/N, and highest dielectric breakdown strength E_bd~224 kV/cm among the five synthesized samples. The correlation between structural, dielectric, ferroelectric, and piezoelectric properties of the BST ceramic with increasing BCT content have been systematically described on the basis of domain wall motion and grain size effect.