Aluminothermal synthesis and characterization of Li3V2−xAlx(PO4)3 cathode materials for lithium ion batteries

Monoclinic Li₃V_2−xAl_x(PO₄)₃ with different Al³⁺ doping contents (x = 0, 0.05, 0.08, 0.10 and 0.12) have been prepared by a facile aluminothermal reaction. Aluminum nanoparticles have been used as source for Al³⁺ and nucleus for Li₃V_2−xAl_x(PO₄)₃ nucleation as well as reducing agent in the aluminothermal strategy. The products were investigated by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and electrochemical methods. The XRD results show that the as-obtained Li₃V_2−xAl_x(PO₄)₃ has a phase-pure monoclinic structure, irrespective of the Al³⁺ doping concentration. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) results reveal that the charge-transfer resistance of the Li₃V₂(PO₄)₃ is reduced and the reversibility is enhanced after V³⁺ substituted by Al³⁺. In addition, The Li₃V_2−xAl_x(PO₄)₃ phases exhibit better cycling stability than the pristine Li₃V₂(PO₄)₃.     

Surface modification of Li1.3Al0.3Ti1.7(PO4)3 ceramic electrolyte by Al2O3-doped ZnO coating to enable dendrites-free all-solid-state lithium-metal batteries

The Na⁺ super-ionic conductor (NASICON) type solid electrolytes Li_1.3Al_0.3Ti_1.7(PO₄)₃ (LATP) are of increasing interest because of their high total ionic conductivity and excellent stability against moist air. However, they are not stable when contacting with lithium metal because of the rapid Ti⁴⁺ reduction by Li metal, which greatly restrict their application in lithium batteries. Here, we propose a Al₂O₃-doped ZnO (AZO) surface coating method by magnetron sputtering to improve the stability of the Li_1.3Al_0.3Ti_1.7(PO₄)₃ electrolyte against the attack of lithium-metal anode and to avoid the growth of lithium dendrite. The Al₂O₃-doped ZnO coating of the electrolyte Li_1.3Al_0.3Ti_1.7(PO₄)₃ demonstrates high chemical stability against the attack of lithium-metal in a wide electrochemical potential ranges (>5 V), as well as an excellent performance of suppressing of lithium dendrites. Furthermore, the Al₂O₃-doped ZnO coated Li_1.3Al_0.3Ti_1.7(PO₄)₃ was found to be the candidate electrolyte for the all-solid-state lithium battery. An all-solid-state Li/LiFePO₄ battery with Al₂O₃-doped ZnO coated Li_1.3Al_0.3Ti_1.7(PO₄)₃ as the solid electrolyte shows good cyclability and a high columbic efficiency for 50 charge/discharge cycles. Furthermore, the surface-modified electrolyte Li_1.3Al_0.3Ti_1.7(PO₄)₃ by Al₂O₃-doped ZnO coating also enables the lithium metal battery to exhibit extremely long cycling for nearly 1000 h due to the ability of suppressing of lithium dendrites.     

Sc3+-doping effects on porous Li3V2(PO4)3/C cathode with superior rate performance and cyclic stability

An enhanced sol-gel combustion method was used to synthesize different porous Sc³⁺-doped Li₃V_2-xSc_x(PO₄)₃/C (x = 0.00, 0.05, 0.10 and 0.15) compounds. The substitution of Sc³⁺ into the V³⁺ sites of Li₃V_2-xSc_x(PO₄)₃/C expands the lattice volume along with the enlargement of Li⁺ diffusion channel, which is beneficial for Li⁺ transportation and ionic conductivity improvement. Besides, the Sc³⁺ doping content exhibits a great impact on the morphology of Li₃V_2-xSc_x(PO₄)₃/C composite. The pristine Li₃V₂(PO₄)₃/C are constituted of porous particles and nanorods, and the ratio of nanorods to particles can be controlled by adjusting the amount of Sc³⁺ doping since the ratio of nanorods to particles decreases with increasing Sc³⁺ doping content. When Sc³⁺ doping content increases to a certain level (x = 0.15, Li₃V_1.85Sc_0.15(PO₄)₃/C), the nanorods are hardly seen. Li₃V_1.90Sc_0.10(PO₄)₃/C with higher tapped density, better reversibility, smaller resistance and larger Li⁺ diffusion coefficient demonstrates outstanding rate performance and cyclic stability, together with high specific discharge capacities of 130.2 and 92.9 mAh g⁻¹ at 0.5 and 20 C, respectively. Furthermore, a superior specific discharge capacity of 85.8 mAh g⁻¹ was retained at 20 C following 1000 cycles. Overall, a novel approach for the preparation of high-performance Li₃V_2-xSc_x(PO₄)₃/C cathodes with different morphologies for lithium-ion batteries is provided.     

Design of Ti4+-doped Li3V2(PO4)3/C fibers for lithium energy storage

In this work, we propose a facile approach to fabricate Ti⁴⁺-doped Li₃V₂(PO₄)₃/C (abbreviated as C-LVTP) nanofibers using an electrospinning route followed by a high temperature treatment. In this designed nanocomposite, the ultrafine LVTP dots are homogeneously dispersed into one-dimensional carbon nanofibers and the Ti⁴⁺ doping does not destroy the crystal structure of monoclinic Li₃V₂(PO₄)₃. Compared to the undoped Li₃V₂(PO₄)₃/C (abbreviated as C-LVP), the as-fabricated C-LVTP fibers present higher reversible capacity, superior high-rate capability as well as better cyclic property. Especially, the C-LVT_7%P cathode delivers not only high capacities of 187.2 and 160.3 mAh g^?1 at 0.5 and 10 C respectively, but also stable cyclic property with the reversible capacity of 135.8 mAh g^?1 at 20 C following 500-cycle spans. The good battery characteristics of C-LVT_7%P can be mainly ascribed to Ti⁴⁺ doping, which can increase the electrical conductivity and Li⁺ diffusion coefficient.     

Synthesis and electrochemical properties of Co-doped Li3V2(PO4)3 cathode materials for lithium-ion batteries

Co-doped Li₃V_2−xCo_x(PO₄)₃/C (x = 0.00, 0.03, 0.05, 0.10, 0.13 or 0.15) compounds were prepared via a solid-state reaction. The Rietveld refinement results indicated that single-phase Li₃V_2−xCo_x(PO₄)₃/C (0 ≤ x ≤ 0.15) with a monoclinic structure was obtained. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the cobalt is present in the +2 oxidation state in Li₃V_2−xCo_x(PO₄)₃. XPS studies also revealed that V⁴⁺ and V³⁺ ions were present in the Co²⁺-doped system. The initial specific capacity decreased as the Co-doping content increased, increasing monotonically with Co content for x > 0.10. Differential capacity curves of Li₃V_2−xCo_x(PO₄)₃/C compounds showed that the voltage peaks associated with the extraction of three Li⁺ ions shifted to higher voltages with an increase in Co content, and when the Co²⁺-doping content reached 0.15, the peak positions returned to those of the unsubstituted Li₃V₂(PO₄)₃ phase. For the Li₃V_1.85Co_0.15(PO₄)₃/C compound, the initial capacity was 163.3 mAh/g (109.4% of the initial capacity of the undoped Li₃V₂(PO₄)₃) and 73.4% capacity retention was observed after 50 cycles at a 0.1 C charge/discharge rate. The doping of Co²⁺into V sites should be favorable for the structural stability of Li₃V_2−xCo_x(PO₄)₃/C compounds and so moderate the volume changes (expansion/contraction) seen during the reversible Li⁺ extraction/insertion, thus resulting in the improvement of cell cycling ability.     

Enhanced electrochemical performance of Li3V2(PO4)3 structurally converted from LiVOPO4 by graphite nanofiber addition

In this work, the structural conversion of LiVOPO₄ to Li₃V₂(PO₄)₃ due to the addition of graphene nanofiber (GNF) was investigated, and the resulting materials were found to exhibit enhanced capacity and cyclability. First, LiVOPO₄ was synthesized using a solid-state method followed by annealing at 900 °C for 12 h under nitrogen atmosphere. Then, the conversion from the triclinic LiVOPO₄ structure to the monoclinic Li₃V₂(PO₄)₃ structure due to the GNF addition was observed. No impurity peak was observed in the X-ray diffraction patterns of LiVOPO₄ or Li₃V₂(PO₄)₃, and the structural conversion caused no defects to form in the resulting Li₃V₂(PO₄)₃ crystallite. Field emission-scanning electron microscope studies clearly demonstrate that larger corroded-structure-like particles formed which were mixed with GNF. This provided both a large active area and fast transport of lithium ions, which afforded enough active sites for simultaneous intercalation of many lithium ions, leading to improved electrochemical properties of the material. Compared with LiVOPO₄, the Li₃V₂(PO₄)₃–GNF showed better properties, such as an improved lithium ion diffusion coefficient, improved cyclability, and smaller impedance. Furthermore, the optimized Li₃V₂(PO₄)₃–GNF (7%) battery showed the best discharge capacity of 181 mA h g⁻¹ at 0.1 C and lithium ion diffusion coefficient of 6.01×10⁻⁹ cm² s⁻¹.     

Porous spherical LiFePO4·LiMnPO4·Li3V2(PO4)3@C@rGO composites as a high-rate and long-cycle cathode for lithium ion batteries

The porous spherical LiFePO₄·LiMnPO₄·Li₃V₂(PO₄)₃@C@rGO (Sample-G) composites are prepared via a spray drying process. The results show that the composites consist of orthorhombic olivine-type LiFe_0.5Mn_0.5PO₄ and monoclinic Li₃V₂(PO₄)₃, which are evenly distributed. In particular, nanoparticles are embedded in graphene nanosheets, which are interconnected and stacked to form a porous sphere structure with an interior three-dimensional conductive network, resulting in the huge improvement on electrochemical performance and structural stability. Due to the increased Li⁺ diffusion coefficient, the composite possesses 98.6 and 82.9 mAh g⁻¹ with capacities retention of 81.6% and 71.8% at 10 and 20C after 1000 cycles, respectively. The mutual cross-doping effect between LFP·LMP·LVP and a porous sphere structure with a 3D conductive network inside provides a practical method for improving the cycling and rate performance.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

Silicon and its effect on the electrochemical properties of Li3V2(PO4)3 cathode material

In this study, silicon and its effect on the properties of Li₃V₂(PO₄)₃ were studied for lithium-ion battery applications. The composite material was synthesized and found to show enhanced capacity and cyclability. The presence of silicon in the composites was confirmed. Furthermore, large particles with rough, corroded-like structures formed, and these were distributed well with the silicon particles. The Li₃V₂(PO₄)₃-Si battery had good properties showing improved cyclability, an improved high performance rate, smaller impedance values and improved lithium-ion diffusion coefficients, as determined by cyclic voltammetry. Furthermore, the optimization of the silicon content led to a Li₃V₂(PO₄)₃-Si battery with a 2?wt% silicon loading that had a discharge capacity of 181?mA?h?g^?1. At 2?C, Li₃V₂(PO₄)₃-Si (2?wt%) still demonstrated a capacity of 111.8?mA?h?g^?1, which was 83.8% of its original capacity (compared with 70.3?mA?h?g^?1 and 63.8% for Li₃V₂(PO₄)₃) after 400 cycles.     

Regenerating the used LiFePO4 to high performance cathode via mechanochemical activation assisted V5+ doping

The wide usage of LiFePO₄ batteries makes their recovery and recycling urgent. Here, a novel, efficient and environmentally friendly recycling process has been developed to recover high performance LiFePO₄ nano composites from spent LiFePO₄ materials. The process comprises an intensive mechanochemical activation through mixing with precursor mixture and one-step solid state heat treatment. Spent LiFePO₄, V₂O₅, Li₂CO₃, and NH₄H₂PO₄ are mixed according to the molar ratio of 1-xLiFePO₄@xLi₃V₂(PO₄)₃ (x?=?0, 0.005, 0.01, 0.03 and 0.1). In the typical process, the decomposition of self-contained binder and the conductive carbon provide a reducing environment as well as an in-situ coating carbon source. The SEM, XRD and XPS results illustrate that V⁵⁺ is doped in the Fe²⁺ site when x?<?0.01, with co-existence of V⁵⁺ doping and Li₃V₂(PO₄)₃ when x?≥?0.03. Sole V⁵⁺ doping assisted in-situ carbon coating displays the best electrochemical performance. The optimized sample shows discharge capacities of 154.3?mA?h?g^?1 and 142.6?mA?h?g^?1 at 0.1 and 1?C rates, respectively, with a high capacity retention of nearly ～100% after 100 cycles. All results indicate that intensive mechanochemical activation assisted V⁵⁺ doping is a promising strategy for spent LiFePO₄ recycling.     

Study on synthesis routes and their influences on chemical and electrochemical performances of Li3V2(PO4)3/carbon

In this study, Li₃V₂(PO₄)₃/carbon samples were synthesized by two different synthesis routes. Their influence on chemical and electrochemical performances of Li₃V₂(PO₄)₃/carbon as cathode materials for lithium-ion batteries was investigated. The structure and morphology of Li₃V₂(PO₄)₃/carbon were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscope (TEM) measurements. TEM revealed that the Li₃V₂(PO₄)₃ grains synthesized through the sol-gel route had a depressed grain size. Electrochemical behaviors were characterized by galvanostatic charge/discharge, cyclic voltammetry and AC impedance measurements. Li₃V₂(PO₄)₃/carbon with smaller grain size showed better performances in terms of the discharge capacity and cycle stability. The improved electrochemical properties of the Li₃V₂(PO₄)₃/carbon were attributed to the depressed grain size and enhanced electrical contacts produced via the sol-gel route. AC impedance measurements also showed that the sol-gel route significantly decreased the charge-transfer resistance and shortened the migration distance of lithium ion.     

Synthesis and electrochemical properties of a composite LiMn0.63Fe0.37PO4 with Li3V2(PO4)3 for lithium-ion battery cathode materials

A composite materials LiMn_0.63Fe_0.37PO₄ with Li₃V₂(PO₄)₃ can be synthesized by a sol-gel method using N,N-dimethylformamide (DMF) as a dispersing agent. The structures, characteristics of the appearance, and electrochemical properties of the composites have been studied by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), charge/discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS). The composites contained LiMnPO₄/C (LMP/C), LiFePO₄/C (LFP/C), and Li₃V₂(PO₄)₃/C (LVP/C) phases with a nano-sized dispersion. The TEM images showed that the composites are crystalline with a grain size of 10–50 nm. The Mn2p, V2p, and Fe2p valence states were analyzed by X-ray photoelectron spectroscopy (XPS). The incorporation of LVP and LFP with LMP effectively enhanced the electrochemical kinetics of the LMP phase by a structural modification and shortened the lithium diffusion length in LMP. The capacity of the composite 0.79LiMn_0.63Fe_0.37PO₄·0.21Li₃V₂(PO₄)₃/C remained at 152.3 mAh g⁻¹ (94.7%) after 50 cycles at a 0.05 C rate. The composite exhibited excellent reversible capacities 159.4, 150, 140.1, 133.7 and 123.6 mAh g⁻¹ at charge-discharge rates of 0.05, 0.1, 0.2, 0.5 and 1 C, respectively.     

Crystal structure and electrochemical performance of Li3V2(PO4)3 synthesized by optimized microwave solid-state synthesis route

To investigate the crystal structure and electrochemical performance of samples synthesized under different microwave solid-state synthesis condition, a series of Li₃V₂(PO₄)₃ samples has been synthesized at five different temperatures for 3-5 min and at 750 °C for various time. The as-synthesized Li₃V₂(PO₄)₃ samples are characterized and studied by ICP-AES analysis, X-ray diffraction (XRD), Rietveld analysis, scanning and transmission electron microcopy (SEM and TEM). At relatively lower temperature (650 °C) and very short reaction time (3 min), pure phase of Li₃V₂(PO₄)₃ could be synthesized in microwave irradiation field. The crystal structure and Li atomic fractional coordinate present a significant deviation upon the change of microwave irradiation temperature and time. Relatively, the diffusion ability of lithium cations and the electrochemical performance are affected. Under the proper reaction temperature and time, the carbon-free samples MW750C5m and MW850C3m show the best specific discharge capacity 126.4 and 132 mAh g⁻¹ at the voltage range of 3.0-4.3 V, near the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). At the voltage range of 3-4.8 V, the sample MW750C5m presents the best initial specific charge capacity of 197 mAh g⁻¹, equivalent to the reversible cycling of three lithium ions per Li₃V₂(PO₄)₃ formula unit (197 mAh g⁻¹). The initial discharge capacity, the samples MW750C5m and MW850C3m present high specific discharge capacity 183.4 and 175.7 mAh g⁻¹, respectively. The relationship among microwave irradiation condition, crystal structure, lithium atomic fractional coordinates and the electrochemical performance have been discussed in detail.     

Effect of Sn doping on the electrochemical performance of NaTi2(PO4)3/C composite

In this paper, NaTi_2-xSn_x(PO₄)₃/C (x?=?0.0, 0.2, 0.3, and 0.4) composites were fabricated via facile sol-gel method, and employed as anodes for aqueous lithium ion batteries. Effect of Sn doping with various content on electrochemical properties of NaTi₂(PO₄)₃/C was investigated systematically. Sn doping on Ti site has no obvious effect on the lattice structure and morphology of NaTi₂(PO₄)₃/C. Among all samples, NaTi_1.7Sn_0.3(PO₄)₃/C (NC-Sn-3) demonstrates the best electrochemical properties. NC-Sn-3 exhibits the outstanding rate performance, delivering a discharge capacity of 103.3, 95.2, and 87.4?mAh?g^?1 at 0.5, 7, and 20?°C, respectively, 1.7, 30.5, and 56.2?mAh?g^?1 larger than those of pristine NaTi₂(PO₄)₃/C. In addition, NC-Sn-3 shows excellent cycling performance with the capacity retention of 80.6% after 1000 cycles at 5?°C. This work reveals that Sn doped NaTi₂(PO₄)₃/C with outstanding electrochemical properties are potential anode for aqueous lithium ion batteries.     

Synthesis and characterization of carbon-coated Li3V2(PO4)3 cathode materials with different carbon sources

The carbon-coated monoclinic Li₃V₂(PO₄)₃ (LVP) cathode materials were synthesized by a solid-state reaction process under the same conditions using citric acid, glucose, PVDF and starch, respectively, as both reduction agents and carbon coating sources. The carbon coating can enhance the conductivity of the composite materials and hinder the growth of Li₃V₂(PO₄)₃ particles. Their structures and physicochemical properties were investigated using X-ray diffraction (XRD), thermogravimetric (TG), scanning electron microscopy (SEM) and electrochemical methods. In the voltage region of 3.0-4.3 V, the electrochemical cycling of these LVP/C electrodes all presents good rate capability and excellent cycle stability. It is found that the citric acid-derived LVP owns the largest reversible capacity of 118 mAh g⁻¹ with no capacity fading during 100 cycles at the rate of 0.2C, and the PVDF-derived LVP possesses a capacity of 95 mAh g⁻¹ even at the rate of 5C. While in the voltage region of 3.0-4.8 V, all samples exhibit a slightly poorer cycle performance with the capacity retention of about 86% after 50 cycles at the rate of 0.2C. The reasons for electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ composites are also discussed. The solid-state reaction is feasible for the preparation of the carbon coated Li₃V₂(PO₄)₃ composites which can offer favorable properties for commercial applications.     

The influence of carbon content on the lithium diffusion and electrochemical properties of lithium vanadium phosphate

The influence of carbon content and porosity of lithium vanadium phosphate, Li₃V₂(PO₄)₃, on its diffusion properties and electrochemical performance was examined by GITT and galvanostatic charge/discharge experiments. The diffusion coefficient of Li₃V₂(PO₄)₃, as determined by GITT measurements, appears relatively high, thus making this material interesting also for high power application. Moreover, the results of this study clearly show that the porosity and the carbon content of the electrode materials is an important factor affecting the diffusion as well as the electrochemical performance of Li₃V₂(PO₄)₃. It was demonstrated that excessive carbon coating may lead to kinetic hindrances but may also contribute specific capacity in anode materials in voltage regions below 1.0 V versus Li/Li⁺.     

Effect of Fe-doping followed by C+SiO2 hybrid layer coating on Li3V2(PO4)3 cathode material for lithium-ion batteries

A novel Li₃V₂(PO₄)₃ composite modified with Fe-doping followed by C+SiO₂ hybrid layer coating (LVFP/C-Si) is successfully synthesized via an ultrasonic-assisted solid-state method, and characterized by XRD, XPS, TEM, galvanostatic charge/discharge measurements, CV and EIS. This LVFP/C-Si electrode shows a significantly improved electrochemical performance. It presents an initial discharge capacity as high as 170.8 mA h g⁻¹ at 1 C, and even delivers an excellent initial capacity of 153.6 mA h g⁻¹ with capacity retention of 82.3% after 100 cycles at 5 C. The results demonstrate that this novel modification with doping followed by hybrid layer coating is an ideal design to obtain both high capacity and long cycle performance for Li₃V₂(PO₄)₃ and other polyanion cathode materials in lithium ion batteries.     

Electrochemical performance of Li3V2(PO4)3/C cathode materials using stearic acid as a carbon source

The Li₃V₂(PO₄)₃/C cathode materials are synthesized by a simple solid-state reaction process using stearic acid as both reduction agent and carbon source. Scanning electron microscopy and transmission electron microscopy observations show that the Li₃V₂(PO₄)₃/C composite synthesized at 700 °C has uniform particle size distribution and fine carbon coating. The Li₃V₂(PO₄)₃/C shows a high initial discharge capacity of 130.6 and 124.4 mAh g⁻¹ between 3.0 and 4.3 V, and 185.9 and 140.9 mAh g⁻¹ between 3.0 and 4.8 V at 0.1 and 5 C, respectively. Even at a charge–discharge rate of 15 C, the Li₃V₂(PO₄)₃/C still can deliver a discharge capacity of 103.3 and 112.1 mAh g⁻¹ in the potential region of 3.0–4.3 V and 3.0–4.8 V, respectively. Based on the analysis of cyclic voltammograms and electrochemical impedance spectra, the apparent diffusion coefficients of Li ions in the composites are in the region of 1.09 × 10⁻⁹ and 4.95 × 10⁻⁸ cm² s⁻¹.     

Microwave solid-state synthesis and electrochemical properties of carbon-free Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using microwave solid-state synthesis method. The refined cell parameters and atomic coordination of the sample MW5m show some deviations compared with those of the sample synthesized in conventional solid-state synthesis method, especially the coordinate of Li atoms. Compared with the electrochemical properties of the carbon-coating sample Li₃V₂(PO₄)₃, the carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage of 3.0-4.3 V, MW5m sample presents a specific charge capacity of 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and specific discharge capacity of 126.4 mAh g⁻¹. In the cut-off voltage of 3.0-4.8 V, MW5m shows an initial specific discharge capacity of 183.4 mAh g⁻¹ at 0.1 C, near the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method, more capacity lost at relatively higher charge/discharge voltage. The reasons for the excellent electrochemical properties of Li₃V₂(PO₄)₃ rapidly synthesized in microwave field are discussed in detail.     

Evaluation of the electrochemical behavior and structural reversibility of Li3−xNaxV2(PO4)3/C (0≤x≤3) as anode materials for Na-ion batteries

A series of Li_3−xNa_xV₂(PO₄)₃/C (0≤x≤3) materials are successfully prepared by a simple solid-state reaction method and used for the first time as anode materials for Na-ion batteries. Powder X-ray diffraction (XRD) results show that the phase structures of Li_3−xNa_xV₂(PO₄)₃/C evolve along with the change of Li/Na atomic ratio (0≤x≤3). With increasing x in Li_3−xNa_xV₂(PO₄)₃/C from 0.0 to 3.0, the main phase in as-prepared sample transforms from monoclinic Li₃V₂(PO₄)₃ to rhombohedral Li₃V₂(PO₄)₃, and finally to rhombohedral Na₃V₂(PO₄)₃, which results in different sodium storage behavior and performance between Li_3−xNa_xV₂(PO₄)₃/C (0≤x≤3) materials. Electrochemical results show that Li_3−xNa_xV₂(PO₄)₃/C (x=0.0, 0.5, 1.0, 1.5, 2.0, 2.5 and 3.0) can deliver the initial charge capacities of 21.1, 35.9, 33.8, 41.7, 43.3, 43.9 and 47.7 mAh g⁻¹ at a current density of 10 mA g⁻¹, respectively. After 45 cycles, the reversible capacities can be kept at 16.9, 45.1, 32.6, 44.6, 43.7, 37.8 and 27.3 mAh g⁻¹ for Li₃V₂(PO₄)₃/C, Li_2.5Na_0.5V₂(PO₄)₃/C, Li₂NaV₂(PO₄)₃/C, Li_1.5Na_1.5V₂(PO₄)₃/C, LiNa₂V₂(PO₄)₃/C, Li_0.5Na_2.5V₂(PO₄)₃/C and Na₃V₂(PO₄)₃/C, respectively. Furthermore, the structural reversibility of Li_3−xNa_xV₂(PO₄)₃/C (x=1.0, 2.0, and 3.0) is also observed by in-situ XRD observation during sodiation/de-sodiation process. All these observed evidences indicate that only some of Li_3−xNa_xV₂(PO₄)₃/C (0≤x≤3) can be used as possible sodium storage materials.