Fabrication and characterization of a mullite-foamed ceramic reinforced by in-situ SiC whiskers

In this study, a new mullite-foamed ceramic, reinforced with in-situ SiC whiskers (MCS) and applied as the insulating lining of thermal equipment used in cement production, was investigated. Compared with a conventional mullite-foamed ceramic (MC), the MCS phase composition, microstructure, compressive strength, thermal conductivity and alkali corrosion resistance were investigated by using X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, and Factsage® software. The results showed that after being fired in granular coke, the SiC whiskers formed into MCS struts and were distributed in the pores between the interconnected needle-like mullite. Although the formation of SiC with higher conduction slightly increased MCS thermal conductivity, it significantly enhanced the compressive strength and alkali corrosion resistance of the foamed ceramic. Compared with the MC, although the MCS had higher bulk density (3.9%), and higher thermal conductivity (9.5% at 800 °C), it was more important that greatly improved compressive strength (by 60%) and better alkali corrosion resistance was achieved.     

Preparation of self-reinforcement of porous mullite ceramics through in situ synthesis of mullite whisker in flyash body

Self-reinforced porous mullite ceramics were fabricated by a starch consolidation method with flyash, different aluminium sources (Al(OH)₃ and Al₂O₃) and the additive AlF₃ as raw materials. The reinforcement mechanism of needle-like mullite whiskers through in situ synthesis in ceramic body was investigated. The bulk density, apparent porosity and bending strength of the samples were tested. Phase compositions and microstructures of the sintered samples were measured by XRD and SEM, respectively. It showed that AlF₃ as additive was helpful to the formation of mullite whiskers at a low temperature. As the aluminium sources, Al(OH)₃ was more suitable for the preparation of mullite whiskers than Al₂O₃. The in situ synthesized mullite whiskers formed an interlocking structure, which enhanced the mechanical strength of the porous mullite ceramics. Porous mullite ceramics with bending strength of about 100 MPa and apparent porosity of about 55% were made at 1550 °C.     

以硼砂为助熔剂使用含钛高炉渣制备发泡陶瓷

以紫色页岩、含钛高炉渣为原料,硼砂为助熔剂,碳化硅为发泡剂制备发泡陶瓷,通过对气孔率、闭孔率、孔径分布、表观密度、抗压强度、导热系数进行测量,研究了原料配比和硼砂添加量对发泡陶瓷气孔结构和物理性能的影响。结果显示:当原料中含钛高炉渣比例增加时,试样的平均孔径增加,气孔均匀性下降;硼砂的加入会使试样抗压强度降低,孔隙率增大,导热系数变小。当发泡陶瓷原料配比(质量分数)为高炉渣30%,页岩70%,添加4%的硼砂和0.2%的碳化硅时,制备出的发泡陶瓷的表观密度为0.374 g·cm^-3,导热系数为0.121 W·m^-1·K^-1,抗压强度为2.59 MPa,满足建筑外墙保温发泡陶瓷的要求。发泡陶瓷主要晶相为斜长石,同时伴有部分透辉石、石英和少量的铁板钛矿。     

Fibrous porous mullite ceramics modified by mullite whiskers for thermal insulation and sound absorption

In order to meet the demand for thermal insulation and sound absorption, fibrous porous mullite ceramics (FPMC) with high porosity and an interconnected pore structure were prepared, followed by a pore structure modification with in situ grown mullite whiskers on the three-dimensional framework of the FPMC. The resultant hierarchical material exhibited superior sound absorption performance in the low-to-medium frequency to most reported sound-absorbing materials, as well as a sufficient compressive strength of 1.26 MPa with low thermal conductivity of 0.117 W·m^?1·K^?1. Moreover, the effects of solid content and mullite whiskers on the microstructure and physical properties of the material were analyzed. The increase of solid content led to increased compressive strength and thermal conductivity and decreased frequency corresponding to the first sound absorption peak. The thermal conductivity and compressive strength of the material increased as the mullite whiskers grew, while the median pore size decreased.     

Preparation of foamed ceramics from steel slag with high calcium and iron content

In this paper, steel slag foamed ceramics were fabricated by using steel slag, kaolin, feldspar, and quartz as main raw materials, and adding SiC as high-temperature foaming agent. The effects of steel slag content and SiC particle size on porosity and mechanical properties of foamed ceramics were researched. Results indicate that when content of steel slag is 40 wt%, and particle size of SiC is 20 µm, foamed ceramics exhibited optimized properties: water absorption rate of 2.59%, total porosity of 55.91%, bulk density of 1.33 g·cm⁻³, and compressive strength of 1.21 MPa. The results show that with the increase of steel slag content, the phase composition of foamed ceramics changes, and foam process is hindered. The increase of steel slag content contributes to the formation of diopside. Fe³⁺, Fe²⁺ in liquid phase enter into diopside by solid solution, the amount of liquid phase decreases. Liquid phase mass transfer slows down, and content of SiC in liquid phase decreases, so that the porosity decreases. At the same steel slag content, different SiC particle size affects the difference between pressure inside the closed pore and surface pressure, thereby the porosity changes.     

Effects of in situ synthesized mullite whiskers on compressive strength of mullite fiber brick

The method of in situ synthesis of mullite whiskers by gas-phase deposition and reaction was applied to improve the compressive strength of the mullite fiber brick. During the preparation process, silica sol, Al(NO₃)₃ solution and NH₄F solution were introduced into the fibrous brick in the form of ions or sol through vacuum impregnation and freeze drying, and the silica sol, Al(NO₃)₃ and NH₄F served as the silica sources, aluminum source and catalyst, respectively. Effects of process parameters (concentration of impregnation solutions, holding time, sintering temperature) on compressive strength and elastic modulus of the fibrous brick during the in situ toughening process were analyzed. SEM and XRD analysis results demonstrated that the mullite whiskers were synthesized on the surface of mullite fibers based on the reaction of AlOF and SiF₄. What is more, the whiskers on adjacent fibers intersected with each other and formed many unfixed lap-jointing points, resulting in the increase of compressive strength and elastic modulus. Although the density and thermal conductivity of the sample after the generation of mullite whiskers fabricated with the optimum process were 0.406 g/cm³ and 0.1262 W/(m K), respectively, which were slightly higher than that of the raw fibrous brick (0.375 g/cm³ density and 0.1069 W/(m K) thermal conductivity, respectively), the corresponding compressive strength and elastic modulus of the sample reinforced with the whiskers increased to 1.45 MPa and 42.03 MPa, respectively, which were much higher than that of the raw fibrous brick (0.39 MPa compressive strength and 6.5 MPa elastic modulus).     

Porous mullite ceramics with enhanced compressive strength from fly ash-based ceramic microspheres: Facile synthesis,structure, and performance

Porous mullite ceramics are widely used in heat insulation owing to their high temperature and corrosion resistant properties. Reducing the thermal conductivity by increasing porosity, while ensuring a high compressive strength, is vital for the synthesis of high-strength and lightweight porous mullite ceramics. In this study, ceramic microspheres are initially prepared from pre-treated high-alumina fly ash by spray drying, and then used to successfully prepare porous mullite ceramics with enhanced compressive strength via a simple direct stacking and sintering approach. The influence of sintering temperature and time on the microstructure and properties of porous mullite ceramics was evaluated, and the corresponding formation mechanism was elucidated. Results show that the porous mullite ceramics, calcined at 1550 °C for 3 h, possess a porosity of 47%, compressive strength of 31.4 MPa, and thermal conductivity of 0.775 W/(m?K) (at 25 °C), similar to mullite ceramics prepared from pure raw materials. The uniform pore size distribution and sintered neck between the microspheres contribute to the high compressive strength of mullite ceramics, while maintaining high porosity.     

Seed assisted in-situ synthesis of porous anorthite/mullite whisker ceramics by foam-freeze casting

Porous anorthite/mullite whisker ceramics with both high strength and low thermal conductivity have been successfully prepared by combining seed-assisted in situ synthesis and foam-freeze casting techniques. The addition of mullite seed was conducive to a reduction in the sintering shrinkage, pore size, and anorthite grain size. This increased the high aspect ratio of mullite whiskers, which enhanced the strength and diminished the thermal conductivity. Mullite whiskers overlapped to form a stable three-dimensional network structure similar to the bird's nest, which was also beneficial to heighten the mechanical properties of the prepared porous ceramics. Through this method, the prepared materials had a high apparent porosity of 87.7–90.2%, a low bulk density of 0.29–0.36 g/cm³, a high compressive strength of 0.65–3.31 MPa, and low thermal conductivity of 0.067–0.112 W/m·K. The results indicated that the method described here can fabricate porous ceramics with excellent properties for further thermal insulating applications.     

Effect of Ca and Mg on the properties of foamed ceramics prepared with multisolid waste

With vanadium tailings and lead-zinc tailings as the main raw materials, gold tailings, waste glass powder, other fluxes and SiC foaming agents are added to prepare foamed ceramics. The effects of Ca and Mg in the fluxes of calcite, talc, and dolomite on the appearance, pore size, porosity, bulk density, and compressive strength of the samples were investigated and the mechanisms of the effects were analyzed. The XRD results showed that the sample consisted primarily of quartz, albite, augite, and a small amount of corundum. Calcite favors the formation of the augite phase, talc favors the formation of the albite phase, and dolomite combines the advantages of both. The formation of albite reduces the viscosity of the melt, and the formation of augite greatly enhances the strength of foamed ceramics. It has been shown that by adding 8% dolomite, a foaming ceramic with a bulk density of .561 g/cm³, a porosity of 62.77% and a compressive strength of 10.823 MPa can be prepared, resulting in a low-cost, lightweight and high strength foamed ceramic partition.     

Effect of SiC nanoparticles on in-situ synthesis of SiC whiskers in corundum–mullite–SiC composites obtained by carbothermal reduction

Corundum–mullite–SiC composites were synthesised using a carbothermal reduction method. The effects of SiC nanoparticles and sintering temperatures on the phase transformation of the composites and the synthesis of SiC whiskers were studied by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Results indicated that corundum, mullite, and SiC whiskers were produced as final products at 1600–1650 °C. SiC whiskers were formed through the vapor–solid mechanism. The added SiC nanoparticles worked as nucleating agents to facilitate the carbothermal reduction of aluminosilicates and formation of SiC whiskers. The sample with the added SiC nanoparticles exhibited a high yield of β-SiC of 17.1%. Furthermore, the SiC nanoparticles decreased the formation temperature of SiC whiskers from the original 1600 °C to 1500 °C, and the porosity of the composites was increased from 56.7% to 64.7% by increasing the partial pressure of SiO gas. This study provides an insight into the more efficient synthesis of composites with SiC whiskers through the carbothermal reduction of aluminosilicates.     

Lightweight and thermal insulation mullite fibers/whiskers hierarchical framework materials: Low-temperature in-situ growth method and mechanism

Mullite fibers/whiskers hierarchical structure materials (MFWs) were prepared via the three-stage method, i.e. seeds breeding, precursors introducing and whiskers growth. The mechanism of low-temperature in-situ synthesis of mullite whiskers during gas-phase reaction process has been discussed in detail. The seeds bred on mullite fibers (MFs) are the growth points and can effectively reduce the subsequent growth temperature of mullite whiskers (MWs). The precursors composed of aluminum source, silicon source and catalyst provided raw materials for whiskers growth. Under the heat treatment temperature of 800 °C, mullite seed grains were guided to in-situ transform into MWs. Moreover, MFWs fabricated via low-temperature in-situ growth mechanism on the MFs present low density (0.103–0.147 g/cm³) and ultralow thermal conductivity (0.0426–0.0514 W·m^?1·K^?1). Due to the lower whiskers growth temperature in this work than the ones in the most recent literatures, the three-stage method can be regarded as a viable strategy for low-temperature in-situ growth whiskers.     

Low‐Density Open Cellular Silicon Carbide Foams from Sucrose and Silicon Powder

Open cellular SiC foams with low densities were prepared by thermo‐foaming and setting (130°C–150°C) of silicon powder dispersions in molten sucrose followed by pyrolysis and reaction sintering at 1500°C. The bubbles generated in the dispersion by water vapor produced by the –OH condensation was stabilized by the adsorption of silicon particles on the air‐molten sucrose interface. The composition of a sucrose‐silicon powder mixture for producing SiC foam without considerable unreacted carbon was optimized. The sucrose in the thermo‐foamed silicon powder dispersion leaves 24 wt% carbon during the pyrolysis. The sintering additives such as alumina and yttria promoted the silicon‐carbon reaction. SiC nanowires with diameters in the range of 35–55 nm and length >10 μm observed on the cell walls as well as in the fractured strut region were grown by both vapor–liquid–solid and vapor–solid mechanisms. Large SiC foam bodies without crack could be prepared as the total shrinkage during pyrolysis and reaction sintering was only ~30 vol%. The relatively low compressive strength (0.06–0.41 MPa) and Young's modulus (14.9–24.2 MPa) observed was due to the large cell size (1.1–1.6 mm) and high porosity (93%–96%).     

多孔碳化硅陶瓷的原位氧化反应制备及其性能

以SiC为陶瓷骨料,Al2O3作为添加剂,通过原位氧化反应制备了Sic多孔陶瓷,并对其氧化反应特性及性能进行了研究.结果表明:在1 300～1 500℃,随烧结温度的升高,SiC的氧化程度增加,SiC多孔陶瓷的强度逐渐增加,但开口孔隙率有所降低.莫来石相在1 500℃开始生成·当烧结温度升高到1 550℃时,莫来石大量生成,得到了孔结构相互贯通且颈部发育良好的莫来石结合SiC多孔陶瓷;由于在SiC颗粒表面上覆盖了致密的莫来石层,SiC的氧化受到抑制,开口孔隙率因而升高,SiC多孔陶瓷的强度因莫来石的大量生成而增加.由平均粒径为5.0um的SiC,并添加20%(质量分数)Al2O3,经1 550℃烧结2h制备的SiC多孔陶瓷具有良好的性能,其抗弯强度为158.7MPa、开口孔隙率为27.7%.     

High-toughness mullite ceramics fabricated by hot-press sintering of pyrophyllite and AlOOH at low temperatures

High-toughness mullite ceramics were fabricated through hot-press sintering (HPS) of pyrophyllite and AlOOH, which were wet-milled and well mixed using a planetary ball mill. The impacts of sintering temperatures and contents of AlOOH on mullite phase formation, densification, microstructure and mechanical properties in ceramic materials were investigated through XRD, SEM and mechanical properties determination. The results indicated that high-toughness mullite ceramics could be successfully prepared by HPS at temperatures higher than 1200°C for 120 min. Increasing the sintering temperature from 1000 to 1300°C significantly enhanced the flexural strength and fracture toughness of samples. The highest flexural strength of 297.97±25.32 MPa and fracture toughness of 4.64±0.11 MPa⋅m^1/2 were obtained for samples sintered at 1300°C. Further increase of temperature to 1400°C resulted in slight decrease of flexural strength and fracture toughness. Compared with the mullite ceramics prepared only using pyrophyllite as raw material, incorporation of AlOOH into raw material significantly increased the mechanical properties of final mullite ceramics. And stoichiometric AlOOH and pyrophyllite as starting material gave the best performance in fracture toughness. The high-toughness of mullite ceramics were ascribed to the high mullite phase content, fine mullite whiskers and in situ formed, intertwined three-dimensional network structure obtained through HPS at a low temperature of 1300°C.     

粉煤灰发泡陶瓷的制备及性能研究

面对日益匮乏的陶瓷原料,利用固体废弃物来制备发泡陶瓷已是当今趋势。以粉煤灰为主要原料,研究铬渣掺量、碎玻璃掺量和粉磨工艺对粉煤灰发泡陶瓷的影响。结果表明,掺入适量的铬渣可改善粉煤灰发泡陶瓷的性能,小掺量的碎玻璃对粉煤灰发泡陶瓷的性能影响较小。当原料配比为m(粉煤灰)∶m(铬渣)∶m(长石)∶m(碎玻璃)=60∶10∶20∶10时,采用湿法粉磨3 h,可以制得平均孔径为0.64 mm,体积密度为368.54 kg/m³,抗压强度为8.11 MPa的发泡陶瓷。     

Porous mullite ceramics with low thermal conductivity prepared by foaming and starch consolidation

Porous mullite ceramics were prepared from an industrial grade mullite powder by foaming and starch consolidation. The viscosities of the original suspensions and the foamed ones with solid loading of 62.5 and 67.5 wt% were measured. After the steps of forming and drying, the green bodies were sintered under different temperatures from 1,200 to 1,600 °C for 2 h. The influence of solid loading of suspension and sintering temperature on the porosity and compressive strength was evaluated. The sintered mullite ceramics, with porosity from 86 to 73 vol% and corresponding compressive strength from 1 to 22 MPa, contained a multi-modal microstructure with large spherical pores and small pores on internal walls. Thermal conductivity measurement carried out by the transient plane source technique at room temperature resulted in values as low as 0.09 W/mK. In addition, the relationship between thermal conductivity and porosity was discussed in detail.     

Recycling of waste red mud for fabrication of SiC/mullite composite porous ceramics

SiC/mullite composite porous ceramics were fabricated from recycled solid red mud (RM) waste. The porous ceramics were formed using a graphite pore forming agent, RM, Al(OH)₃ and SiC in the presence of catalysts. The influence of firing temperature and the pore-forming agent content on the mechanical performance, porosity and the microstructure of the porous SiC ceramics were investigated. Optimal preparation condition were determined by some testing. The results indicated that the flexural strength of specimens increased as a function of firing temperature and a reduction in graphite content, which concomitantly decreased porosity. The ceramic prepared under optimal conditions having 15?wt% graphite and sintered at 1350?°C, demonstrated excellent performance. Under optimal preparation conditions the flexural strength and porosity of the ceramic were 49.4?MPa and 31.4%, respectively. Scanning electron microscopy observation result showed that rod-shape mullite grains endowed the samples with high flexural strength and porosity. X-ray diffraction analysis indicated that the main crystallization phases of the porous ceramics were 6H-SiC, mullite, cristobalite and alumina. This work demonstrates that RM can be sucessfully reused as a new raw material for SiC/mullite composite porous ceramics.     

Effects of SiC,SiO2 and CNTs nanoadditives on the properties of porous alumina-zirconia ceramics produced by a hybrid freeze casting-space holder method

Highly porous alumina-zirconia ceramics were produced by adding space-holder materials during freeze casting. To increase the strength of porous ceramics, different amounts of nanoadditives (silicon carbide-SiC, silica-SiO₂, and multi-wall carbon nanotubes-CNTs) were added. Space-holder materials were removed by preheating, and solid samples were produced by sintering. Up to 68% porosity was achieved when 40% space-holder was added to the solid load of slurry. Wall thicknesses between pores were more uniform and thinner when nanoadditives were added. Compressive tests revealed that SiC nanoparticles increased the strength more than other nanoadditives, and this was attributed to formation of an alumina-SiC phase and a uniform distribution of SiC nanoparticles. Results indicated that by including 20% space-holder materials and 15% SiC nanoparticles, the density decreases by 33.8% while maintaining a compressive strength of 132.5 MPa and porosity of 43.4%. Relatively low thermal conductivities, less than 3.5 W/K-m, were measured for samples with SiC nanoparticles.     

Microstructure and properties of porous anorthite/mullite whiskers ceramics with high porosity

Porous anorthite/mullite whiskers ceramics with high porosity (>91%) and high strength (>0.45 MPa) have been successfully prepared by foam gel-casting method. Effects of extra mullite whiskers on properties including thermal conductivity and compressive strength at different temperatures were investigated and discussed in terms of microstructure observed through SEM and TEM. The results showed that the addition of extra mullite whiskers in certain content could effectively reduce thermal conductivity, improve the compressive strength both at room and high temperature at same time. When the mullite whiskers content was 20 mol%, the porosity was as high as 91.6 ± 0.19%, the thermal conductivity was low to 0.034 ± 0.003 W/(m·K), and the compressive strength at 1000°C was high to 0.64 ± 0.11 MPa three times to the pure one. Small pores, small grains, and more phase interface or grain boundary caused by the addition of extra mullite whiskers were the main factors for low thermal conductivity. Meanwhile, small pores, closely bonded small grains, and the stable three-dimension network formed by mullite whiskers helped to improve strength.     

Thermodynamic properties of aluminum titanate-mullite composite ceramics containing heat stabilizer

Using Al₂O₃ and TiO₂ as raw materials, adding MgO as heat stabilizer and mullite as enhancer, aluminum titanate-mullite multiphase ceramics were successfully prepared by solid phase synthesis. The effects of MgO and mullite were systematically studied on the phase composition, microstructure, thermal stability, sintering properties, and mechanical properties of aluminum titanate ceramics. The results showed that the introduction of Mg²⁺ can partially replace Al³⁺ to form Mg_xAl_2(1-x)Ti_(1+x)O₅ solid solution, improved the thermal stability of aluminum titanate ceramics, and promoted the formation and growth of grains, which reduced the sintering temperature. The crack deflections caused by mullite particles improved the mechanical properties. The filling effect of mullite particles and the formation of silica in mullite raw materials were conducive to ceramic densification. The statistics of Mg4M10 sample were as follows: the porosity was only 2.9%, the flexural strength was as high as 64.15 MPa, and the thermal expansion coefficient was 1.35 × 10⁻⁶ K⁻¹ (RT-700°C), encouraging the application of ceramics with high thermal mechanical properties.