Effect of MgO addition on the properties of PbO –TiO2–B2O3 glass and glass–ceramics

Glass samples with composition of (50?X) PbO–X MgO–25 TiO₂–25B₂O₃ (where X=0, 5, 10 and 15 mol%) were prepared using conventional quenching technique. The amorphous nature of glass samples were confirmed by XRD. The glass transition temperature, T_g and crystallization temperature T_c were determined from the DTA. It has been observed that the addition of MgO enhances the T_g. The rise in T_g with MgO content may be attributed to the greater field strength of Mg²⁺ cation (as compared to Pb²⁺) which leads to the formation of stronger bonds. These glass samples were converted to glass–ceramics by following a two-stage heat treatment schedule. It was observed that there was good correlation between the density and CTE results of the glass–ceramics. The XRD results revealed the formation of tetragonal lead titanate as a major crystalline phase in the glass–ceramics. The addition of MgO to the glass contributes to the formation of MgB₄O₇. The dielectric constant for all the glass–ceramic samples was observed to be higher than that of corresponding glass samples. Further, with addition of MgO the room temperature dielectric constant for glass–ceramic samples increases up to 10 mol% of MgO and then decreases for 15 mol%. It has been further observed that the variation of dielectric constant of glass–ceramic samples with MgO content is exactly opposite to the variation of crystallite size of PbTiO₃ embedded in the glass ceramic-samples.     

Effect of P2O5 on evolution of microstructure of MgO–Al2O3–SiO2 glass ceramics

Abstract

MgO–Al₂O₃–SiO₂ (MAS) cordierite based glass ceramics were prepared by volume crystallisation. X-ray diffraction, Scanning electron microscopy and Energy diffraction scanning were used to investigate crystallisation behaviour and the influence of P₂O₅ on microstructure MAS based glass ceramics. The results showed that P⁵⁺ could promote the phase separation of MAS glass and that the glass was divided into two areas, such as Mg₄Al₂Ti₉O₂₅ and the containing P⁵⁺ area at <900°C. Mg₄Al₂Ti₉O₂₅ and Mg₃(PO₄)₂ in the area were both advantageous to the precipitation of μ cordierite, which further transformed to α cordierite due to P⁵⁺ in the residual glassy phase. However, P⁵⁺ inhibited the presence of cordierite when the heat treatment temperature was >900°C.     

Modification of glass network and crystallization of CaO–Al2O3–MgO–SiO2 based glass ceramics with addition of iron oxide

Modification of glass network and crystallization process of a CaO–Al₂O₃–MgO–SiO₂ (CAMS) based glass ceramic to form diopside through addition of iron oxide were investigated using differential thermal analysis (DTA), Raman spectrum, X-ray diffraction, SEM and EBSD techniques. The experimental results showed that addition of Fe₂O₃ led to remarkable reductions in both the glass transition temperature (Tg) and crystallization temperature (Tp) of the CAMS glass ceramic. At addition level below 5 wt%, the Tg and Tp temperatures were 651°C and 903°C, respectively, and the crystallization only occurred on the surface of the glass ceramic samples. Increasing the addition level to 10 wt% and 15 wt%, not only led to reduction in the Tg and Tp temperatures to 643-641°C and 892-876°C, respectively, but also promoted the formation of crystalline diopside throughout the CAMS samples. Based on the results of Raman spectrums, it was confirmed that Fe₂O₃ addition reduced the strength of glass connection as a result of chemical reactions between the isolated Si–O tetrahedron and Fe³⁺ ion, forming Fe³⁺O₄–SiO₄, which can be regarded as Q₂ unit. And this is the first experimental evidence that proving the approach of Fe³⁺ mending glass network. Microstructural examination also identified the formation of large numbers of spherical Fe-enriched regions within the CAMS glass matrix as a result of the amorphous phase separation due to the Fe₂O₃ addition. The interfaces between the Fe-enriched regions and the glass matrix acted as preferred nucleation sites for the diopside, facilitating the crystallization. Crystallographic analysis using EBSD technique determined the <001> as the most favorite growth direction for the diopside crystals in the CAMS based glass ceramic.     

Phase transformation and microstructure of MgO–Al2O3–SiO2 system glass–ceramics under different heat treatment conditions

Abstract

Effects of heat treatment conditions on phase transformation, microstructure and thermal expansion coefficient (TEC) in MgO–Al₂O₃–SiO₂ system glass–ceramics were investigated by means of differential thermal analysis, X-ray diffraction and scanning electron microscopy. The magnesium aluminium titanate (MAT) precipitated firstly at 850°C and β-quartz solutions (β-QSS) formed at 950°C. Further increasing temperature to 1000°C, MAT disappeared and β-QSS became master phase, following little amount of α-cordierite, MgTi₂O₅, rutile and sapphirine. When glass was treated at 1050°C, β-QSS content decreased and α-cordierite became master phase. As temperature reached higher than 1100°C, β-QSS and sapphirine disappeared, and α-cordierite became master phase accompany with rutile and MgTi₂O₅ as secondary phase. The microstructure transformed gradually from particle shape crystallites to slat shape network with the increase in heat treatment temperature. By controlling heat treatment condition, an ideal glass–ceramics with proper TEC for matching sealing to 4J29 alloy has been obtained.     

Crystallisation and characterisation of dielectric glass ceramics in Li2O–Al2O3–SiO2 system

Abstract

Glass ceramics in the Li₂O–Al₂O₃–SiO₂ system have been synthesised to produce bulk materials grown in a glass phase via quenching followed by controlled crystallisation. The crystallisation and microstructure of Li₂O–Al₂O₃–SiO₂ (LAS) glass–ceramic with nucleating agents (B₂O₃ and/or P₂O₅) are investigated by differential thermal analysis, X-ray diffraction and scanning electron microscopy and the effects of B₂O₃ and P₂O₅ on the crystallisation of LAS glass are also analysed. The introduction of both B₂O₃ and P₂O₅ promotes the crystallisation of LAS glass by decreasing the crystallisation temperature and adjusting the crystallisation kinetic parameters, allows a direct formation of β spodumene phase and as a result, increases the crystallinity of the LAS glass ceramic. Microstructural observations show that the randomly oriented, nanometre sized crystalline is found with residual glass concentrated at crystallite boundaries. Furthermore, it is interesting that codoping of B₂O₃ and P₂O₅ creates not much effect on the crystallisation temperature. The dielectric properties of the glass–ceramics formed through controlled crystallisation have a strong dependence on the phases that are developed during heat treatment. The dielectric constant is continuously increased and the dielectric loss is decreased with addition of additives where mobile alkali metal ions (e.g. Li⁺) are incorporated in a crystal phase and minimise the residual glass phase.     

Shaped MgO–Al2O3–SiO2 refractory ceramics from recycled materials

Abstract

The aim of the present work is to prepare, characterise and assess MgO–Al₂O₃–SiO₂ refractory ceramics; namely, spinel, mullite and cordierite from chemically recycled precipitates. These precipitates include pure and fine magnesium and aluminium hydroxides as well as water treated fumed silica. Corresponding batches of the aimed oxide ceramics were coprecipitated from these precipitates and subsequently processed up to firing using the proper techniques. The processed bodies were investigated for their chemical and phase composition as well as morphology, microstructure and physical properties. According to the results of these investigations, the processed ceramics could be recommended for the adequate applications. It is concluded that dense, direct bonded and highly refractory spinel and mullite–corundum bodies could be obtained after firing their coprecipitated batches up to 1700°C. On the other side, dense, porous and refractory cordierite–spinel bodies could be processed from its batch after firing up to 1350°C. All of these bodies are refractory oxide ceramics with a very wide range of thermo-chemical, physical and mechanical applications.     

Characterization and sintering of gels in the system MgO–Al2O3–SiO2

Cordierite aerogels, made by supercritical drying, and xerogels, formed by ambient pressure drying, have been prepared by combining two different recipes. The chemical composition of the gels varied from stoichiometric cordierite 2MgO·Al₂O₃·5SiO₂ to 0·5MgO·1·4Al₂O₃·5SiO₂ due to different procedures for washing of the gels. The crystallization of nearly stoichiometric cordierite gels was shown to be relatively complex involving the formation of several metastable phases such as μ-cordierite (Mg₂Al₄Si₅O₁₈), spinel (Al₆Si₂O₁₃) and sapphirine (Mg₄Al₈Si₂O₂₀) before the equilibrium phase composition was obtained at around 1350°C. On the other hand, during crystallization of gels with stoichiometry close to 0·5MgO·1·4Al₂O₃·5SiO₂ the equilibrium phases mullite, cristobalite and α-cordierite were the major phases formed during heat treatment. A lower densification rate was observed for aerogels compared to xerogels due to a larger pore size. A lower crystallization temperature in aerogels probably due to heterogeneous nucleation reduced the densification. For gels with a composition near 0·5MgO·1·4Al₂O₃·5SiO₂ nucleation and densification occur simultaneously and large differences in the densification behavior was observed. ©     

Low-temperature hot-press sintering of AlN ceramics with MgO–CaO–Al2O3–SiO2 glass additives for ceramic heater applications

Aluminum nitride (AlN) is used a ceramic heater material for the semiconductor industry. Because extremely high temperatures are required to achieve dense AlN components, sintering aids such as Y₂O₃ are typically added to reduce the sintering temperature and time. To further reduce the sintering temperature, in this study, a low-melting-temperature glass (MgO–CaO–Al₂O₃–SiO₂; MCAS) was used as a sintering additive for AlN. With MCAS addition, fully dense AlN was obtained by hot-press sintering at 1500 °C for 3 h at 30 MPa. The mechanical properties, thermal conductivity, and volume resistance of the sintered AlN–MCAS sample were evaluated and compared with those of a reference sample (AlN prepared with 5 wt% Y2O3 sintering aid sintered at 1750 °C for 8 h at 10 MPa). The thermal conductivity of AlN prepared with 0.5 wt% MCAS was 91.2 W/m?K, which was 84.8 W/m?K lower than that of the reference sample at 25 °C; however, the difference in thermal conductivity between the samples was only 14.2 W/m?K at the ceramic-heater operating temperature of 500 °C. The flexural strength of AlN–MCAS was 550 MPa, which was higher than that of the reference sample (425 MPa); this was attributed to the smaller grain size achieved by low-temperature sintering. The volume resistance of AlN–MCAS was lower than that of the reference sample in the range of 200–400 °C. However, the resistivity of the proposed AlN–MCAS sample was higher than that of the reference sample (500 °C) owing to grain-boundary scattering of phonons. In summary, the proposed sintering strategy produces AlN materials for heater applications with low production cost, while achieving the properties required by the semiconductor industry.     

Preparation of glass–ceramic glazes in the SiO2–Al2O3–CaO–MgO–K2O–Na2O–ZnO system by variable content of ZnO

This paper is focused on glass–ceramic glazes from the SiO₂–Al₂O₃–CaO–MgO–K₂O–Na₂O system with ZnO additions (2.5, 5, 10, 15, 15, 20 and 25 wt%). The compositions were designed based on constant molar ratio of SiO₂/Al₂O₃. In the resulting glazes diopside (CaMg[Si₂O₆]), willemite (Zn₂SiO₄) and vitreous phase were identified by X-ray diffraction. Morphological and structural date of these glazes were supplementary determined by EPMA, FTIR and Raman Spectroscopy. DSC analysis was carried out to characterize thermal properties of the materials.     

Effect of CaO doping on the properties and crystallization behavior of Y2O3–Al2O3–SiO2 glass

Nowadays, Y₂O₃–Al₂O₃–SiO₂ (YAS) glass joining is considered to be a promising scheme for nuclear-grade continuous silicon carbide (SiC) fiber reinforced SiC matrix composites (SiC/SiC). CaO has great potential for nuclear applications since it has low reactivity and low decay rate under nuclear irradiation. In this paper, the effect of CaO doping on the structure, thermophysical properties, and crystallization behavior of YAS glass was systematically studied. As the CaO doping content increased, the number of bridge oxygens and the viscosity at high temperatures reduced gradually. After heat treatment at 1400 °C, the main phases in YAS glass were β-Y₂Si₂O₇, mullite, and SiO₂ (coexistence of crystalline and glass phases), while that with 3.0% CaO doping turned into a single glassy phase under the same treatment conditions. Moreover, a structural model and the modification mechanism were proposed, which provided a theoretical basis for the subsequent component design and optimization.     

Thermal Stability and Crystallization Kinetics of MgO–Al2O3–B2O3–SiO2 Glasses

To support commercialization of the MgO–Al₂O₃–B₂O–SiO₂-based low-dielectric glass fibers, crystallization characteristics of the relevant glasses was investigated under various heat-treatment conditions. The study focused on the effects of iron on the related thermal properties and crystallization kinetics. Both air-cooled and nucleation-treated samples were characterized by using the differential thermal analysis/differential scanning calorimeter method between room temperature and 1200°C. A collected set of properties covers glass transition temperature (T_g), maximum crystallization temperature (T_p), specific heat (ΔC_p), enthalpy of crystallization (ΔH_cryst), and thermal stability (ΔT=T_p—T_g). Using the Kinssiger method, the activation energy of crystallization was determined. Crystalline phases in the samples having various thermal histories were determined using powder X-ray diffraction (XRD) and/or in situ high-temperature XRD method. Selective scanning electron microscope/energy-dispersive spectroscopy analysis provided evidence that crystal density in the glass is affected by the iron concentration. Glass network structures, for air-cooled and heat-treated samples, were examined using a midinfrared spectroscopic method. Combining all of the results from our study, iron in glass is believed to function as a nucleation agent enhancing crystal population density in the melt without altering a primary phase field. By comparing the XRD data of the glasses in two forms (bulk versus powder), the following conclusions can be reached. The low-dielectric glass melt in commercial operation should be resistant to crystallization above 1100°C. Microscopic amorphous phase separation, possibly a borate-enriched phase separating from the silicate-enriched continuous phase can occur only if the melt is held at temperatures below 1100°C, that is, below the glass immiscibility temperature. The study concludes that neither crystallization nor amorphous phase separation will be expected for drawing fibers between 1200°C and 1300°C in a commercial operation.     

Determination of surface area and porosity of sol–gel derived ceramic powders in the system TiO2–SiO2–Al2O3

The surface characteristics of ternary ceramic powders in the system TiO₂–SiO₂–Al₂O₃ prepared by a sol–gel technique were studied through nitrogen gas adsorption at liquid nitrogen temperature and application of the Brunauer–Emmett–Teller (BET) equation. The total surface area, total pore volume and pore radius of the powders were calculated through the construction of plots relating the amount of nitrogen gas adsorbed V₁ and the thickness of the adsorbed layer t (V₁−t plots). These results permitted the detection of the different types of pores present in the samples. In a first approximation, the V₁−t plots seem to demonstrate the correctness of the results obtained for the total specific area of the investigated samples. The influence of thermal treatment (drying, calcination) on the surface characteristics of the investigated powders was assessed.     

Effect of TiO2 on crystallization and mechanical properties of MgO–Al2O3–SiO2 glasses containing P2O5

MgO–Al₂O₃–SiO₂ glass-ceramics have been widely used in military, industrial, and construction applications. The nucleating agent is one of the most important factors in the production of glass-ceramics as it can control the crystallization temperature or the grain size. In this study, we investigated the effect of replacing P₂O₅ with different amounts of TiO₂ on the crystallization, structure, and mechanical properties of an MgO–Al₂O₃–SiO₂ system. The crystallization and microstructure were investigated by differential scanning calorimetry, Raman spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The mechanical properties were investigated by measuring the Vickers hardness, Young's modulus, and fracture toughness. The results showed that adding TiO₂ favored the precipitation of fine grains and significantly increased the Vickers hardness, Young's modulus, and fracture toughness of the glasses. Introducing an appropriate amount of TiO₂ can make a glass structure more compact, promote crystallization, and improve the mechanical properties of MgO–Al₂O₃–SiO₂ glass-ceramics.     

The role of MgO on the structural properties of CaO–Na2O(MgO)–P2O5–CaF2–SiO2 derived glass ceramics

The effect of increasing MgO/Na₂O replacements (on mole basis) on the crystallization characteristics of glasses based on the CaO–Na₂O(MgO)–P₂O₅–CaF₂–SiO₂ system were studied by using DTA, XRD, and SEM. The crystallization characteristics of the glasses, the type of crystalline phases formed and the resulting microstructure were investigated. The main crystalline phases formed after controlled heat-treatment of the base glass were diopside, wollastonite solid solution, fluoroapatite and sodium calcium silicate phases. The increase of MgO at the expense of Na₂O led to decrease the amount of sodium calcium silicate phase. The Vicker's microhardness values (5837–3362 MPa) of the resulting glass–ceramics were markedly improved by increasing the MgO-content in the glasses. The obtained data were correlated to the nature and concentration of the crystalline phases formed and the resulting microstructure.     

Influence of Li2O–B2O3–SiO2 glass on the sintering behavior and microwave dielectric properties of BaO–0.15ZnO–4TiO2 ceramics

This paper reports the investigation of the performance of Li₂O–B₂O₃–SiO₂ (LBS) glass as a sintering aid to lower the sintering temperature of BaO–0.15ZnO–4TiO₂ (BZT) ceramics, as well as the detailed study on the sintering behavior, phase evolution, microstructure and microwave dielectric properties of the resulting BZT ceramics. The addition of LBS glass significantly lowers the sintering temperature of the BZT ceramics from 1150 °C to 875–925 °C. Small amount of LBS glass promotes the densification of BZT ceramic and improves the dielectric properties. However, excessive LBS addition leads to the precipitation of glass phase and growth of abnormal grain, deteriorating the dielectric properties of the BZT ceramic. The BZT ceramic with 5 wt% LBS addition sintered at 900 °C shows excellent microwave dielectric properties: ε_r=27.88, Q×f=14,795 GHz.     

Modelling and optimizing the liquid phase sintering of alumina/CaO–SiO2–Al2O3 ceramics using response surface methodology

Alumina is an attractive material for engineering applications due to its unique properties. In this study, CaO–SiO₂–Al₂O₃ eutectic phase was used as an additive phase and liquid phase sintering of the alumina/CaO–SiO₂–Al₂O₃ samples were investigated. The liquid phase sintering was modelled and optimized by Response Surface Methodology (RSM) using Central Composite Design (CCD) to achieve maximum fracture strength and density as responses. Sintering temperature, alumina particles size distribution (PSD), lubricant and eutectic phase content were selected as independent variables. Two cubic models were developed in terms of these variables to describe the responses. The validity and accuracy of the models were checked using Analysis of Variance (ANOVA).Phase identification of the synthesized eutectic phase was evaluated by XRD and fracture strength of the sintered samples was determined by Ring-on-Ring test method. SEM was used to study the fracture surface of the samples. The obtained models for predicting fracture strength and density of the sintered samples showed high conformity with the experimental results. Sintering temperature and alumina PSD were found as the most effective parameters. Therefore, optimized condition based on the defined constraints was obtained for sintering temperature of 1533 °C, alumina PSD of 25%, and lubricant and eutectic phase content of 1.5 wt% and 7.5 wt%, respectively. Results showed that after ball milling of the eutectic phase, the fracture strength of the optimized ceramic sample was improved and it reached to maximum values at smaller amounts of the additive phase.     

Experimental investigation on high temperature wettability and structural behaviour of SAW fluxes using MgO–TiO2–SiO2 and Al2O3–MgO–SiO2 flux system

To establish the relationship between wettability and structure with the change in SAW flux composition, the contact angle measurement study was performed at 1700 K. For MgO–TiO₂–SiO₂ and Al₂O₃–MgO–SiO₂ flux system the wetting behaviour was studied by evaluating the contact angle as well as surface tension properties. Sessile drop method was used to determine the wetting properties of SAW fluxes. Twenty-one SAW fluxes were designed & developed by applying mixture design approach of design of experiments. Chemical, phase and structural properties of SAW fluxes were measured using modern techniques such as X-ray fluorescence (XRF), X-ray diffraction (XRD) & Fourier Transform Infra-red spectroscopy (FTIR). As per the calculated contact angle value, different surface tension values for MgO–TiO₂–SiO₂ and Al₂O₃–MgO–SiO₂ flux system was calculated using Young's & Boni's equations. Using Dupre's equation the adhesion energy for twenty-one basic fluxes was also calculated. Measured contact angle value increased with increase in the TiO₂/MgO & TiO₂/Al₂O₃ flux ratio. Lower contact angle gives higher wettability between the flux and the heating substrate. With increase of TiO₂/SiO₂ ratio up to 1.5 to 2.0 the calculated surface tension value is decreasing while after that it is increased with increase in TiO₂/SiO₂ ratio.     

Microstructure and properties of CaO–ZrO2–SiO2 glass–ceramics prepared by sintering

For the development of a new wear resistant and chemically stable glass-ceramic glaze, the CaO–ZrO₂–SiO₂ system was studied. Compositions consisting of CaO, ZrO₂, and SiO₂ were used for frit, which formed a glass-ceramic under a single stage heat treatment in electric furnace. In the sintered glass-ceramic, wollastonite (CaSiO₃) and calcium zirconium silicate (Ca₂ZrSi₄O₁₂) were crystalline phases composed of surface and internal crystals in the microstructure. The internal crystal formed with nuclei having a composition of Ca_1.2Si_4.3Zr_0.2O₈. The CaO–ZrO₂–SiO₂ system showed good properties in wear and chemical resistance because the Ca₂ZrSi₄O₁₂ crystals positively affected physical and mechanical properties.     

Effect of surface properties of MgO on its dissolution and spinel growth in CaO–SiO2–Al2O3 slag

The dissolution behavior of MgO in CaO–SiO₂–Al₂O₃ ternary slag at the interface of single-crystal, dense poly-crystal, and porous poly-crystal MgO was investigated to evaluate the effect of the surface properties of the MgO. The experimental results revealed that a detached spinel layer formed at the MgO interface due to the change in thermodynamic condition of the slag, which was independent of the surface properties. On the other hand, it was also confirmed that the growth rate and morphology of the detached spinel layer strongly depended on the surface properties, such as porosity and curvature of MgO. During the formation of the spinel layer at the interface during MgO dissolution, a kinetic approach adopting parabolic relation theory was employed to determine the correlation between the surface properties and the spinel growth mechanism.