Synthesizing mixed-phase TiO2 nanocomposites using a hydrothermal method for photo-oxidation and photoreduction applications

Mixed-phase titanium dioxide (TiO₂) materials, such as Degussa P25, show high photocatalytic activity due largely to the synergistic effect between anatase and rutile phases, in which spatial charge separation hinders charge recombination. Our previous studies indicate that a particular nanostructured assembly of anatase and rutile crystallites is necessary for the synergy. In this paper, we apply this structure-function understanding to the synthesis of highly active TiO₂ nanocomposite photocatalysts. Using simple synthetic procedures, we demonstrate an ability to design a highly active nanocomposite that shows enhanced photoactivity in both oxidative and reductive chemistry. Studies by electron paramagnetic resonance spectroscopy indicate the existence of the critical nanostructured assembly and thus the optimization of charge transfer between anatase and rutile phases in the synthesized nanocomposite. These results illustrate the potential of rationally designing photocatalysts for energy applications.     

Kinetics of anatase transition to rutile TiO2 from titanium dioxide precursor powders synthesized by a sol-gel process

Kinetics of anatase transition to rutile TiO₂ from titanium dioxide precursor powders synthesized by a sol-gel process have been studied using differential thermal analysis (DTA), X-ray diffraction, transmission electron microscopy (TEM), selected area electron diffraction (SAED), nano beam electron diffraction (NBED) and high resolution TEM (HRTEM). The DTA result shows residual organic matter decomposed at 436 K. The transition temperature for amorphous precursor powders converted to anatase TiO₂ occurred at 739 K. Moreover, the full anatase transition to rutile TiO₂ occurred at 1001 K. The activation energy of anatase TiO₂ formation was 128.9 kJ/mol. On the other hand, the activation energy of anatase transition to rutile TiO₂ was 328.4 kJ/mol. Mesoporous structures can be observed in the TEM image.     

Anatase–rutile transformation of TiO2 sol–gel coatings deposited on different substrates

Titanium dioxide is widely used in a lot of applications. The properties of TiO₂ strongly depend on its phase composition. The transformation temperature between phases is influenced by a lot of factors. One of them is a type of substrate under the TiO₂ film. In presented work, thin films of TiO₂ were deposited by the sol–gel method on silicon, stainless steel (304 L) and Co–Cr–Mo alloy (Vitallium). The process of anatase–rutile phase transformation was investigated by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD) studies of deposited coatings. The results were compared with anatase–rutile transformations temperature of TiO₂ powders obtained by analogous sol–gel process. The temperature of anatase–rutile phase transformation changed in the range of 700–1000 °C and strongly depends on a kind of substrate. It was found that anatase–rutile transformation of TiO₂ coating proceeded at a higher temperature than rutilization of titania powders.     

Carbonaceous-TiO2 nanomaterials for photocatalytic degradation of pollutants: A review

Semiconductor photocatalysis is one of most appealing and attractive technologies, which has been directly utilized to harvest solar energy for energy and environmental applications. Titanium dioxide (TiO₂) has been proved to be leading semiconductor photocatalyst for the degradation of pollutants. However, it suffers from low photocatalytic activity under visible light activation because of its intrinsic wide band gap. Various strategies have been developed to enhance TiO₂ efficiency in the visible light region. Among them TiO₂ modification with carbonaceous nanomaterials is very effective route for excellent photocatalytic activity. This critical review aims to present recent progress in the design and synthesis of carbonaceous-TiO₂ photocatalysts, covering carbon doping, activated carbon, fullerenes, carbon nanotubes and graphene. Moreover, proposed mechanisms of enhancement, effect of synthesis routes, demonstrations of performance and applications reported in literature are reviewed. Ongoing challenges and possible new directions are outlined.     

Effect of silver (Ag) ions irradiation on the structural,optical and photovoltaic properties of Mn doped TiO2 thin films based dye sensitized solar cells

Dye sensitized solar cell (DSSC) is an emerging energy harvesting tool which converts direct sunlight into electrical energy. These cells have much better properties in contrast with silicon based solar cells because of their flexible nature, light weight, low cost, environment friendly nature, and involvement of a simple manufacturing process. Since, a photoanode is the backbone of DSSC, we synthesized a pure and 1% manganese (Mn) doped titanium dioxide (TiO₂) films by sol-gel method which are irradiated with silver (Ag) ions at two different concentrations (2 × 10¹⁴ and 4 × 10¹⁴) ions-cm^?2. X-ray diffraction revealed that Mn doping followed by Ag irradiation transformed TiO₂ from pure anatase to rutile phase. Ultraviolet–visible spectroscopy exposed the reduction in band gap of TiO₂ film during this doping and irradiation process. Therefore, absorption is enhanced with red shift in UV-range. When these films are used as a photoanode in DSSC, 1% Mn doped TiO₂ film exposed with Ag at the concentration of (2 × 10¹⁴) ions-cm^?2 exhibited maximum efficiency of 2.40%.     

Direct synthesis of TiO2 nanoparticles by using the solid-state precursor TiH2 powder in a thermal plasma reactor

We attempt the direct synthesis of TiO₂ by using the solid state precursor TiH₂ powder with oxygen in a thermal plasma reactor. Nanocrystalline titanium dioxide powder has been synthesized by using thermal plasma synthesis in a non-transferred arc thermal plasma reactor. The thermal plasma-synthesized powder product consists of nano-sized particles of anatase and rutile phases of titanium dioxide. Particle compositions were observed on collecting powder from different positions of the reactor and varying the amount of flow rate of reactive gases (O₂). The characteristics of the powder such as particle size, size distribution and phases were analyzed using various techniques such as XRD, SEM, TEM, XPS, EDS and particle size analyzer. UV–visible reflection spectroscopy of the plasma-synthesized TiO₂ powders showed the absorbance in the visible region leading to effective photocatalytic activity, which is clearly confirmed from the XPS analysis. XPS analysis reveals the presence of –OH bonds on the surface of nanoparticles, which is the significant evidence of better quality of powders in comparison to other methods. Also, we have investigated the phase transformation phenomenon of anatase to rutile. At 1000 °C, complete transformation of the anatase to rutile occurs. Powders prepared in this procedure are white in colour and their diameter varies from 10 nm to 150 nm. Average particle size distributes in the range of 20–50 nm. The unique property about the plasma-synthesized powders is high resistance to heat treatment, with enhanced photocatalytic activity.     

Novel nitrogen-doped anatase TiO2 mesoporous bead photocatalysts for enhanced visible light response

This work reports the synthesis and characterization of a novel, high surface area N-doped anatase TiO₂ mesoporous bead as a photocatalyst for visible light photodegradation. The beads were prepared using a two-cycle microwave-assisted hydrothermal method using three different types of nitrogen dopants: diaminohexane, triethylamine, and urea. In the first cycle, TiO₂mesoporous beads with controlled structures were synthesized at 200 °C without further calcination. The obtained beads were then subjected to a second cycle of microwave -assisted hydrothermal process for nitrogen doping. The photocatalytic activity of the N-doped mesoporous TiO₂ beads was determined by measuring the decomposition of a methyl blue aqueous solution under UV and visible light. It was found that different precursors lead to different degrees of doping which enhances the light absorption primarily in the visible light region. We demonstrate that the photocatalytic activity or photodegradation is enhanced in the visible light region.     

Visible light-active sub-5 nm anatase TiO2 for photocatalytic organic pollutant degradation in water and air,and for bacterial disinfection

Visible-light-sensitive sub-5 nm anatase titanium dioxide (TiO₂) nanoparticles (NPs) were fabricated without any doping and calcination treatments. The energy band gap was effectively narrowed to ~ 2.98 eV. The surface and subsurface hydroxyl defects were ascertained as the origin for the band gap narrowing and for the efficient azo-based dye degradation in water and formaldehyde decomposition in air, as well as disinfection of Staphylococcus aureus bacteria, under visible light irradiation.     

Preparation, crystal structure, and photocatalytic activity of TiO2 films by chemical vapor deposition

Photocatalytic activities of TiO₂ films were experimentally studied. TiO₂ films with different crystal structures (amorphous, anatase, rutile) were prepared by a Low Pressure Metal Organic Chemical Vapor Deposition (LPMOCVD) at different reaction temperatures and also by a Sol-Gel method using TTIP (Titanium Tetra Iso-Pro-poxyde). The Effect of CVD preparation method, CVD reaction conditions, crystal structure and wave-length of UV light on the photocatalytic decomposition rate of methylene blue in aqueous solution were studied. First, the characteristics of CVD preparation of TiO₂ films, such as the CVD film growth rate, crystal structure and morphology of the grown TiO₂ films, were experimentally studied as a function of CVD reaction temperature. Secondly, photocatalytic activities of TiO₂ films were evaluated by using two types of photo-reactors. The results indicated that TiO₂ films prepared by CVD exhibit higher photocatalytic activity than a catalyst prepared by the Sol-Gel method. Among the CVD grown TiO₂ films, anatase and rutile showed high photocatalytic activities. However, amorphous TiO₂ films showed lower activities. The activity of the photocatalysts of anatase films was excellent under all types of UV-lamps. The activity of CVD-prepared anatase films was four to seven times higher than that of photocatalyst films prepared by the Sol-Gel method.     

Preparation,structural and photocatalytic activity of Sn/Fe co-doped TiO2 nanoparticles by sol-gel method

Pure and Sn/Fe co-doped (0.2 at.% Sn and 0.6 at.% Fe, 0.6 at.% Sn and 0.2 at.% Fe, 1.0 at.% Sn and 1.0 at.% Fe) TiO₂ nanoparticles were synthesized via a sol-gel method and subsequently calcined at different temperatures. Furthermore, the particles were analyzed by TG-DSC, XRD, TEM, HRTEM, EDS, SAED and UV–Vis for investigating the influences of dopant and calcination temperature on the thermal effect, composition, morphology, energy band gap (E_g) and the degradation efficiency of methyl orange (MO) under various light irradiations respectively. Results indicated that Sn/Fe co-doping inhibited the crystallization transformation from anatase to rutile phase of TiO₂ and decreased the E_g. The increased calcination temperature and Sn/Fe co-doped effect brought about the abnormal grain growth of TiO₂ nanoparticles. 0.6 at.% Sn/0.2 at.% Fe and 1.0 at.% Sn/1.0 at.% Fe co-doped TiO₂ nanoparticles presented better photocatalytic performance than pure and 0.2 at.% Sn/0.6 at.% Fe co-doped TiO₂ nanoparticles under visible light irradiation mainly due to the decreased E_g. On the contrary, 0.2 at.% Sn and 0.6 at.% Fe co-doped TiO₂ nanoparticles calcined at 650 °C showed the most excellent photocatalytic performance under UV light irradiation, which was about twice as large as that of pure TiO₂ possibly due to the formed hybrid structure of anatase and rutile phase as well as the h⁺-mediated decomposition pathway.     

Fabrication of high-efficiency anatase TiO2 photocatalysts using electrospinning with ultra-violet treatment

In metal oxide nanofiber fabrication using the electrospinning method, heat treatment is performed at temperatures of 500°C or higher for crystallization and polymer desorption. Therefore, it is difficult to fabricate low-temperature phase metal oxides that crystallize at low temperatures. TiO₂, a representative metal oxide often used as photocatalysts, is known to have higher photocatalytic activity in the low-temperature phase (anatase structure) than in the high-temperature phase (rutile structure). Studies on the fabrication of TiO₂ anatase nanofibers using conventional electrospinning have reported disadvantages such as the partial expression of rutile structures and low crystallinity. This study developed an anatase TiO₂ nanofiber as a high-efficiency catalyst based on the electrospinning method and a residual organic matter cleaning method that employs ultra-violet (UV) light. We fabricated nanofibers using the electrospinning method and implemented TiO₂ nanofibers with the anatase structure through heat treatment at 260°C. Residual organics remaining after heat treatment of the fabricated crystalized TiO₂ nanofibers were removed by exposing them to UV light, thereby improving photocatalytic efficiency. The photocatalytic efficiency of the fabricated TiO₂ nanofibers was confirmed through a methylene blue (MB) decomposition experiment under visible light irradiation. The photocatalytic efficiency (time taken for the concentration of the MB solution to reach 50%) of the UV-treated TiO₂ nanofibers was approximately six times higher than of P25 and the heat-treated nanofibers.     

Preparation of CdS/TiO2 nanotube arrays and the enhanced photocatalytic property

In this paper, a series of CdS/TiO₂ NTs have been synthesized by SILAR method. The as-prepared CdS/TiO₂ NTs have been analyzed by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive spectrometer (EDS), and ultraviolet–visible (UV–vis). And their photocatalytic activities have been investigated on the degradation of methylene blue under simulated solar light irradiation. XRD results indicate that TiO₂ NTs were anatase phase, CdS nanoparticles were hexagonal phase. FESEM results indicate that low deposition concentration can keep the nanotubular structures. UV–vis results indicate that CdS can be used to improve the absorbing capability of TiO₂ NTs for visible light, and the content of CdS affects the band gap. Photocatalytic results indicate that CdS nanoparticles are conducive to improve the photocatalytic efficiency of TiO₂ NTs, and the highest degradation rate can reach 93.8%. And the photocatalytic mechanism of CdS/TiO₂ NTs to methylene blue is also described.     

Hydrogenation processing of TiO2 nanoparticles

Titanium dioxide (TiO₂) is an important semiconductor material and photocatalyst with applications in a multitude of fields, including water treatment and solar energy. Recently, hydrogenation has been proposed as an effective processing technique to enhance the visible light absorbance of TiO₂, which is typically insensitive to the visible spectrum. In this work, we have elucidated several key synthesis and processing parameters affecting the hydrogenation of TiO₂ nanomaterials. Synthesis protocols, hydrogenation temperature and pressure were revealed to be critical parameters in controlling the H₂ modification of TiO₂ nanoparticles. These findings may contribute to engineering of materials properties of metal oxides through hydrogenation processing. © 2013 Canadian Society for Chemical Engineering     

Synthesis of visible light-active nanostructured TiOx (x < 2) photocatalysts in a flame aerosol reactor

Titanium dioxide is a wide band gap (3.2 eV) semiconductor which is photo-active when irradiated with UV light. For wider scale use of TiO₂ as a photocatalyst, its activity needs to be extended to the visible light region (constituting 45% of total incident solar energy). A diffusion flame aerosol reactor (FLAR) with an oxygen lean environment in the particle formation zone has been used to synthesize oxygen deficient titanium suboxide (TiO_x with x < 2) nanoparticles. Using a standard-based electron energy loss spectroscopy (EELS) technique, the non-stoichiometry (x in TiO_x) in the flame synthesized particles has been quantified with high accuracy (uncertainty less than 3%). Under an oxygen lean environment in the particle formation zone, the non-stoichiometry in the TiO_x particles is a function of the flame temperature. The value of x in the flame synthesized TiO_x nanoparticles is in the range of 1.88 < x < 1.94. Diffuse reflectance spectra confirmed that the oxygen deficient TiO_x particles absorbed visible light. Visible light activity of the TiO_x particles is demonstrated by photocatalytic degradation of methyl orange solution under visible light illumination.     

Photocatalytic Nb2O5-doped TiO2 nanoparticles for glazed ceramic tiles

TiO₂ nanoparticles are currently used as coating for self-cleaning building products. In order to achieve high self-cleaning efficiency for outdoor applications, it is important that titania is present as anatase phase. Moreover, it is desirable that the particle sizes are in nano-range, so that a large enough surface area is available for enhanced catalytic performance. In this work, TiO₂ nanoparticles doped with 0–5 mol% Nb₂O₅ were synthesized by co-precipitation. Nb₂O₅ postponed the anatase to rutile transformation of TiO₂ by about 200 °C, such that after calcination at 700 °C, no rutile was detected for 5 mol% Nb₂O₅-doped TiO₂, while undoped TiO₂ presented 90 wt% of the rutile phase. A systematic decreasing on crystallite size and increasing on specific surface area of TiO₂ were observed with higher concentration of Nb₂O₅ dopant. Photocatalytic activity of anatase polymorph was measured by the decomposition rate of methylene blue under ultraviolet and daylight illumination and compared to commercial standard catalyst (P25). The results showed enhanced catalysis under UV and visible light for Nb₂O₅-doped TiO₂ as compared to pure TiO₂. In addition, 5 mol% Nb₂O₅-doped TiO₂ presented higher photocatalytic activity than P25 under visible light. The enhanced performance was attributed to surface chemistry change associated with a slight shift in the band gap.     

Preparation of titania/carbon nanotube composites using supercritical ethanol and their photocatalytic activity for phenol degradation under visible light irradiation

Titanium dioxide (anatase, TiO₂) nanoparticles have been successfully deposited onto multi-walled carbon nanotubes (MWCNTs) via hydrolysis of titanium isopropoxide in supercritical ethanol. The as-prepared composites were characterized by X-ray diffraction, transmission electron microscopy and X-ray photoelectron spectroscopy. It was demonstrated that the MWCNTs were decorated with well-dispersed anatase nanoparticles less than 7 nm in diameter. The size and loading content of the nanoparticles on MWCNTs could be tuned by manipulating the ratio of precursor to MWCNTs, and the formation mechanism of the composites was also discussed. The absorbance spectrum of the resultant TiO₂/MWCNT composites extended to the whole UV-visible region due to the decoration of TiO₂ on MWCNTs. The TiO₂/MWCNT composites were used as photocatalyst for phenol degradation under irradiation of visible light, which showed higher efficiency compared to a mixture of TiO₂ and MWCNTs.     

Aluminium-doped TiO2 nanotubes with enhanced light-harvesting properties

Titanium dioxide (TiO₂) application in light-harvesting processes is hindered by its wide band gap. Strategies such as morphology shifts from nanoparticles to nanotubes and doping of fabricated nanostructures are widely used to address this issue. Combining both approaches, this work successfully synthesizes, for the first time, aluminium-doped TiO₂ nanotubes via a single-step anodization method at three distinct potentials (20, 40 and 60 V). SEM images revealed the successful formation of remarkably thin layers of TiO₂ nanotubes produced at 40 and 60 V. X-ray diffractograms and Raman spectra suggest the successful insertion of aluminium into the anatase lattice. Diffuse reflectance confirmed the doping process through a marked effect on the absorbance of visible light for the higher voltages, as well as through a reduction in the optical band gap. For utilization purposes, the photoelectrochemical performance of 40 V Al–TiO₂ was able to deliver a comparable response to that of a compact TiO₂ layer of the same thickness. The current density developed by the 60 V sample was increased by 120% in comparison to the undoped material, despite having an absorbance much lower than that of the latter. Overall, synthesizing an Al-doped TiO₂ nanotubular structure has proven to be a great strategy in the development of materials for application in advanced light-harvesting electrodes.     

Photocatalytic degradation of benzene,toluene, ethylbenzene,and xylene (BTEX) using transition metal-doped titanium dioxide immobilized on fiberglass cloth

Transition metal (Fe, V and W)-doped TiO₂ was synthesized via the solvothermal technique and immobilized onto fiberglass cloth (FGC) for uses in photocatalytic decomposition of gaseous volatile organic compounds—benzene, toluene, ethylbenzene and xylene (BTEX)—under visible light. Results were compared to that of the standard commercial pure TiO₂ (P25) coated FGC. All doped samples exhibit higher visible light catalytic activity than the pure TiO₂. The V-doped sample shows the highest photocatalytic activity followed by the W- and Fe-doped samples. The UV-Vis diffuse reflectance spectra reveal that the V-doped sample has the highest visible light absorption followed by the W- and Fe-doped samples. The X-ray diffraction (XRD) patterns indicate that all doped samples contain both anatase and rutile phases with the majority (>80%) being anatase. No new peaks associated with dopant oxides can be observed, suggesting that the transition metal (TM) dopants are well mixed into the TiO₂ lattice, or are below the detection limit of the XRD. The X-ray absorption near-edge structure spectra of the Ti K-edge transition indicate that most Ti ions are in a tetravalent state with octahedral coordination, but with increased lattice distortion from Fe- to V- and W-doped samples. Our results show that the TM-doped TiO₂ were successfully synthesized and immobilized onto flexible fiberglass cloth suitable for treatment of gaseous organic pollutants under visible light.     

Stable anatase phase with a bandgap in visible light region by a charge compensated Ga–V (1:1) co-doping in TiO2

A series of charge compensated Ga–V co-doped TiO₂ samples (Ti_(1-x)(Ga_0.5V_0.5)_xO₂) have been synthesized by a modified sol-gel process. X-ray diffraction pattern shows that the anatase to rutile (A→R) onset temperature (T_O) shifts to a higher temperature, whereas the complete phase transformation temperature (T_C) shifts to a low-temperature region as compared to pure TiO₂, due to Ga–V incorporation. Ga–V co-doping helps in the transformation of some smaller sized Ti⁴⁺ to a relatively larger Ti³⁺. In the anatase phase, oxygen content also increases with increasing doping concentration, which along with the larger size of Ti³⁺ results in lattice expansion and thereby delays the T_O. In the rutile phase, oxygen vacancy increases with increasing doping concentration, which results in lattice contraction and accelerates phase transition. Grain growth process is hindered in the anatase phase (crystallites size reduces from ~15 nm (x = 0.00) to 8 nm (0.10)), whereas it is accelerated in the rutile phase as compared to pure TiO₂. In both phases bandgap (E_g) reduces to the visible light region (anatase: E_g = 3.16 eV (x = 0.00) to 2.19 eV (x = 0.10) and rutile: 3.08 eV (x = 0.00) to 2.18 eV (x = 0.10)) in all co-doped samples. The tail of the absorption edge reveals lattice distortion and increase of Urbach energy proofs the same due to co-doping. All these changes (grain growth, phase transition, and optical properties) are due to lattice distortion created by the combined effect of substitution, interstitials, and oxygen vacancies due to Ga–V incorporation in TiO₂.     

Reaction induced multifunctional TiO2 rod/particle nanostructured materials for screen printed dye sensitized solar cells

This study investigates the potential of utilizing multifunctional nanostructured materials for the efficient light trapping and electron transport in solar cells by combining titanium dioxide (TiO₂) rods and nanoparticles. A simple solvothermal method was adopted for the synthesis of coupled morphology adopting the desired precursor with the constant concentration and temperature. The reaction duration (12, 24, 36 and 48 h) was varied and the materials resultant physical, optical and structural characteristics were elucidated to determine the nature of the prepared material. The crystallographic phase of the synthesized samples was determined with XRD and Raman analysis. From the experimental data it is hypothesized that the surface plane of anatase (105) is involved in the deformation of the structure and the formation of the rutile phase. To further investigate on the formation of mixed phase in the prepared sample a computation study was performed using density functional theory coupled to the Hubbard U correction (DFT + U) as a function of volume in both the anatase and rutile phases. The relative stability of the O–Ti–O networks is explored starting from ultrathin materials for four different sizes, of anatase and rutile nanorods separately. Finally, the synthesized TiO₂ materials were used to prepare screen printed dye sensitized solar cell (DSSC) devices and their respective properties were quantified.