Effects of AlF3 and MoO3 on properties of Mullite whisker reinforced porous ceramics fabricated from construction waste

Mullite-whisker-reinforced anorthite-mullite-corundum porous ceramics were prepared from construction waste and Al₂O₃ powder by adding AlF₃ and MoO₃ as the additive and crystallization catalyst, respectively. The effects of AlF₃ and MoO₃ content on the properties of mullite whiskers, such as open porosity, mechanical properties, pore size distribution, microstructure and phase structure, were investigated in detail. The results showed that the morphology of the mullite whiskers and properties of the porous ceramics were greatly influenced by the AlF₃ and MoO₃ content. The specimen obtained by co-adding 12 wt% AlF₃ and 3 wt% MoO₃, and sintering at 1350 °C for 1 h, exhibited excellent properties, including an open porosity of 67.4±0.5% and biaxial flexural strength of 24.0±0.8 MPa. The mullite whiskers were uniformly distributed; the whiskers had a diameter of 0.05–0.5 µm, length of 8–10 µm, and aspect ratios (length to diameter ratio) of 20–30 on average.     

Preparation of calcium hexaluminate porous ceramics by gel-casting method with polymethyl methacrylate as pore-forming agent

Calcium hexaluminate (CA₆) porous ceramics were prepared by gel-casting method, with α-Al₂O₃ and CaCO₃ as raw materials and polymethyl methacrylate (PMMA) microspheres as pore-forming agent. The effects of the amount of pore-forming agent PMMA microspheres on the phase composition, bulk density, apparent porosity, flexural strength, microstructure, thermal shock stability and thermal conductivity of CA₆ porous ceramics were systematically studied. The pores of CA₆ porous ceramics are mainly formed by the burning loss of PMMA microspheres and the decomposition of organic matter. Adding an appropriate amount of PMMA microspheres as pore-forming agent has a positive effect on the thermal shock stability of CA₆ porous ceramics. When the amount of pore-forming agent is 15 wt%, the volume density of CA₆ porous ceramics is 1.33 g/cm³, the porosity is 63%, the flexural strength is 13.9 MPa, the thermal shock times can reach 9 times, and the thermal conductivity is 0.293 W/(m·K), which can meet the application in refractory, ceramics or high temperature cement industries.     

Preparation and properties of porous mullite-based ceramics fabricated by solid state reaction

In this study, the effect of the alumina particle size on the formation of mullite using a silica gel powder and micro- and nano-scale Al₂O₃ powders as raw materials was investigated. The optimized Al₂O₃ source was then reacted with the silica gel to prepare porous mullite-based ceramics. The results revealed that the highly reactive nano-Al₂O₃ powder could form mullite at a relatively low firing temperature. Therefore, the nano-Al₂O₃ powder was used to prepare porous mullite-based ceramics by firing at 1600 °C, 1650 °C and 1700 °C. The pore size of the prepared porous mullite-based ceramics ranges from tens to hundreds of micrometres, with the apparent porosity being 42.8–58.0%. Further, the mullite content in the samples increased with increasing firing temperature, and a higher firing temperature promoted sintering, resulting in improved strength of the sample. After calcination at 1700 °C, the mullite content in the sample reached 81.8%, and the sample showed excellent thermal shock resistance. The strengths of the samples before and after thermal shock were found to be 23.6 and 15.58 MPa, with the residual strength ratio being 66%.     

Gelcasting of dense and porous ceramics by using a natural gelatine

An improved gel-casting procedure was successfully exploited to produce porous ceramic bodies having controlled porosity features in terms of mean pore size, total pore volume as well as pore geometry. The gel-casting process in which a natural gelatine for food industry is used as gelling agent was firstly set-up to prepare dense alumina and zirconia components. Then, commercial PE spheres, sieved to select proper dimensional ranges, were added to the starting slurries as pore-forming agent. Both alumina and zirconia porous bodies were then produced, having a porosity ranging between 40 and 50 vol%. The fired components were characterised by spherical pores surrounded by highly dense ceramic walls and struts, having a homogeneous and fine microstructure. Their mean pore size was directly dependent on the sieved fraction of the starting PE spheres selected as pore-forming phase.     

Influence of the content of polymethyl methacrylate on the properties of porous Si3N4 ceramics fabricated by digital light processing

Porous Si₃N₄ ceramics are highly regarded as ideal materials for radomes due to their unique characteristics. However, the slurry used for the preparation of porous Si₃N₄ ceramics suffers from a low cure depth, making it challenging to fabricate ceramic components using DLP technology. In this study, porous Si₃N₄ ceramics were prepared by combining DLP technology with pore-forming agent method. The addition of polymethyl methacrylate (PMMA) powders with lower refractive index than that of Si₃N₄ powders can improve the penetration depth of ultraviolet light in the Si₃N₄ slurry. A systematic study was conducted to investigate the influence of the addition of PMMA powders on the properties of Si₃N₄ slurries and porous Si₃N₄ ceramics. When PMMA powders were added at 10 wt%, the slurry with a lowest viscosity of 0.13 Pa s (the shear rate is 30 s⁻¹) and cure depth of 40.0 μm (the exposure energy is 600 mJ/cm²) was obtained. With the increase of PMMA content, porous Si₃N₄ ceramics experienced a gradual decrease in both the flexural strength and bulk density, while the porosity increased from 14.41% to 27.62%. Specifically, when 20 wt% PMMA was added, the resulting porous Si₃N₄ ceramics had a lowest bulk density (2.41 g/cm³), a maximum porosity (27.62%), and a flexural strength (435.87 MPa). The study is of great significance in establishing an experimental foundation for fabricating porous Si₃N₄ ceramics by using DLP technology.     

Structure and properties of Al2O3-bonded porous fibrous YSZ ceramics fabricated by aqueous gel-casting

To meet requirements for high porosity and high strength, novel aqueous gel-casting process has been successfully developed to fabricate Al₂O₃-bonded porous fibrous YSZ ceramics with ρ-Al₂O₃ and YSZ fibers as raw materials. Microstructure, phase composition, apparent porosity, bulk density, thermal conductivity, and compressive strength of fabricated porous ceramics were investigated, and effects of fiber content on properties were discussed. According to results, bird nest 3D mesh with interlaced YSZ fibers and Al₂O₃ binder was formed, ensuring the ability to obtain high performance, lightweight ceramics. An increase in the number of YSZ fibers led to more complex interlaced arrangement of fibers and denser network structure of porous ceramics at retaining their stability. Furthermore, their apparent porosity and bulk density increased, whereas thermal conductivity and compressive strength decreased with increasing the fiber content. In particular, comparatively high porosity (71.1–72.7%), low thermal conductivity (0.209–0.503 W/mK), and relatively high compressive strength (3.45–4.24 MPa) were obtained for as-prepared porous ceramics, making them promising for applications in filters, thermal insulation materials, and separation membranes.     

Microstructure and permeability of porous YSZ ceramics fabricated by freeze casting of oil-in-water suspension

Porous yttria-stabilized zirconia (YSZ) ceramics are fabricated through freeze casting of oil-in-water suspension followed by sintering at 1250−1550 °C. The pore structure, compressive strength and permeability of porous YSZ ceramics are tailored via altering the emulsion content and sintering temperature. The samples obtained using higher emulsion content or at lower sintering temperature show larger Darcian and non-Darcian constants due to their higher open porosity and larger pore size. Furthermore, the investigation on individual contributions of viscous and inertial resistances on the total pressure drop during permeation process indicates that the viscous resistance increases but the inertial resistance decreases with increasing the emulsion content or decreasing the sintering temperature for samples. Porous YSZ ceramics obtained in this work with a k₁ range of 3.14 × 10⁻¹³–1.12 × 10⁻¹² m² are appropriate for applications in filters and membrane supports.     

Novel camphene/photopolymer solution as pore-forming agent for photocuring-assisted additive manufacturing of porous ceramics

This study proposes camphene/photopolymer solutions as a novel pore-forming agent for the photocuring-assisted additive manufacturing of porous ceramics. Unlike conventional techniques using molten camphene, solid camphene can be directly dissolved in the photocurable monomer hexanediol diacrylate (HDDA) at room temperature, which can then crystallize with a dendrite-like morphology based on phase separation at lower temperatures. This unique approach allows alumina suspensions to solidify at ―2 °C and then effectively be photopolymerized using a digital light processing engine, resulting in camphene-rich crystals surrounded by photopolymerized alumina/HDDA walls. Sintered samples exhibited a highly porous structure, with the pores created after the removal of the camphene-rich crystals. Two different pore sizes were obtained in the lower and upper regions of a single layer, due to a decrease in the solidification rate along the building direction, although their porosities were similar (～ 52 vol%). The porous samples exhibited a compressive strength of ～ 265 MPa.     

开孔剂对多孔氧化铝支撑体的影响

研究了开孔剂对a-Al2O3多孔道氧化铝支撑体的影响,发现开孔剂的种类及质量分数对支撑体的性能有重要影响,选择合适的开孔剂种类及质量分数可使氧化铝支撑体的纯水通量提高2～3倍。     

Electrophoretic deposition of yttria-stabilised zirconia powder from aqueous suspensions for fabricating ceramics with channel-like pores

Electrophoretic deposition with simultaneous gas bubble formation by electrolysis can be used for producing ceramic green bodies, typically few millimetres in thickness, with unidirectionally aligned channel-like pores. The method is successfully applied to yttria-stabilised zirconia. Two types of aqueous suspension compositions are investigated. Suspensions with acetic acid additions are particularly suitable for forming green bodies with fine pore channels. Only small amounts of acetic acid, promoting the gas evolution, are needed for this purpose. Dissolution of yttria in the acidic range has to be considered, but the required low acid concentrations do not measurably affect the yttrium content of the deposits. Yttria dissolution can be minimised by a suspension composition containing an anionic polyelectrolyte and ammonia instead of acetic acid. The ammonia concentration influences the size of the tubular pores of the deposits formed under constant-voltage conditions. Using structured deposition electrodes, the regularity of the pore arrangement can be enhanced.     

Ultrastrong tough zirconia ceramics by defects-engineering

We report the preparation of a category of ultrastrong tough zirconia ceramics by engineering defects using an oscillatory pressure during pressure assisted sintering. The introduced oscillatory pressure enhances the dynamic grain rearrangement, plastic deformation, mass transportation, and pore removal, leading to the formation of pore-free ceramics characterized by the rich coherent grain boundaries among individual mesocrystalline grains with intragranular quasi-interfaces. As a proof of concept, the pressure required by oscillatory pressure sintering (OPS) for preparing fully dense 3Y-TZP ceramics is significantly reduced, which is just ∼1/5 of that required by hot isostatic pressing. The OPS-prepared 3Y-TZP ceramics reached a record-breaking high bending strength and fracture toughness, being up to 1.8 GPa and 16 MPa·m^1/2, respectively. This success illustrates a universal principle of engineering defects for making breakthrough in exploring other ultrastrong tough ceramics.     

泡沫陶瓷的研究进展

介绍了泡沫陶瓷的特性、制造工艺、用途及在冶金工业中的应用。指出除现有的堇青石质、氧化铝质、堇青石－氧化铝质过滤器外，还开发了氮化硅质、碳化硅质、氧化铝质产品。     

Novel design of elongated mullite reinforced highly porous alumina ceramics using carbonized rice husk as pore-forming agent

A facile strategy for the fabrication of elongated mullite reinforced porous alumina ceramics (PACs) using carbonized rice husk (CRH) as pore-forming agent and silica source is reported for the first time. A large amount of elongated mullite is synthesized in pores due to the reaction of amorphous silica in CRH skeleton and alumina ceramic powder. Elongated mullite acts as the bridges between pore walls, enhancing the compressive strength of PACs. Furthermore, secondary pores from the intersection of elongated mullite is favor of decreasing of the thermal conductivity. High performance PAC with porosity of 74.3% has been fabricated by employing 25 wt% CRH, which possesses relatively low thermal conductivity of 0.189 W/(m•K) and ultra-high compressive strength of 45 MPa. Its comprehensive performance is much better than that of existing ceramic materials. Our findings present a facile, eco-friendly and effective approach to fabricate high performance PACs as the high-temperature thermal insulation materials.     

Influence of different pore-forming agents on wollastonite microstructures and adsorption capacities

In this study, porous macro- and micro-cellular wollastonite-based ceramics was synthesized. A ceramic precursor, methylhydrocyclosiloxane, together with micro-sized CaCO₃, was used as a starting material. After 20 min of ultrasound treatment, and calcination at 250 °C for 30 min, different pore-forming agents were added to the as-obtained powders. Differential thermal analysis was used to determine characteristic temperatures of processes occurring within powders during heating. Based on the obtained results, the sintering regime was set up. The prepared mixtures were pressed into pallets and sintered at 900 °C. During the sintering regime, porous wollastonite-based ceramics was obtained. The phase composition of the sintered samples, as well as the microstructures, were analyzed by using X-ray diffraction and SEM. A two-phase system was detected in all samples, CaSiO₃ wollastonite and Ca₂SiO₄ larnite, and their ratio varied with each pore-forming agent. It was observed that the addition of different pore-forming agents resulted in significantly different microstructures. In a batch test, the influence of pH, the contact time and the initial ion concentration on the adsorption efficiency of As⁺⁵, Cr⁺⁶and phosphate ions on the synthesized adsorbents were studied. Time-dependent adsorption is best described by the pseudo-second-order kinetic model and the Weber-Morris model, which predict intra-particle diffusion as a rate-controlling step of the overall process. High adsorption capacities, 21.93, 23.88, and 27.29 mg g^–1, were obtained for the CaCO₃-siloxane-nanocellulose sorbent, and similar/lower capacities were obtained for the CaCO₃-siloxane-PMMA and CaCO₃-siloxane-cotton wool adsorbents.     

Pore structure and thermal oxidation curing behavior of porous polymer derived ceramics with superhigh porosity fabricated by freeze casting

Porous ceramics with porosity up to 92.5 % have been successfully fabricated by freeze casting of polycarbosilane (PCS) solution. The effect of PCS concentration and thermal oxidation curing on the pore structure and compressive properties was investigated. Curing mechanism and thermodynamics were illuminated through analyzing the molecular structure, curing activation energy, and curing degree. Porous ceramics, mainly composed of SiC and a small amount of SiO₂, have dendritic pore structure which well replicates the solidification morphology of camphene solvent. Results of FT-IR and Gaussian computation of PCS electron density show that Si–H and Si–CH₃ bonds play a dominant role in thermal oxidation curing reaction. Both curing degree and ceramic yield increase with the increase in curing temperature and time. The curing degree of Si–H bond is close to 52 % and the corresponding ceramic yield is about 83 % when the porous PCS was cured at 200 °C for 90 min. Both polymer concentration and curing time have influences on the compressive strength of porous ceramics.     

Microstructure of TiO2 porous ceramics by freeze casting of nanoparticle suspensions

During freeze casting of TiO₂ porous ceramics, the porous architecture is strongly influenced by TiO₂ particle size, solids loading, and cooling temperature. This work investigates the influences of particle size, freezing substrate, and cooling temperature on the TiO₂ green bodies prepared by freeze casting. The results show that the lamellar channel width with 100 nm particles is larger than that of 25 nm particles, yet the ceramic wall thickness is noticeably decreased. The lamellar structure is more ordered when using a copper sheet than glass as its freezing substrate. A finer microstructure results when frozen at − 50 ℃ than − 30 ℃. Such porous materials have application potentials in a wide range of areas such as photocatalysis, solar cells, and pollutant removal and should be further studied.     

The preparation and characterization of porous alumina ceramics using an eco-friendly pore-forming agent

This work presents the preparation of porous alumina ceramics through the sacrificial phase method, using an eco-friendly material, namely waste coffee grounds, as a pore-forming agent. The effects of coffee grounds content in the green ceramic bodies on the linear and volumetric shrinkage, as well as the total and open porosity of the sintered product, were evaluated. The influence of the resulting porosity on mechanical properties of the prepared porous alumina was determined using Brazilian disk compression test for the determination of the indirect tensile strength of the prepared samples. Microstructure and pores morphology were characterized by scanning electron microscopy. Porosities in the range 35-54 vol% were achieved, by varying the coffee grounds content from 0 to 50 wt% in the green bodies. The indirect tensile strength of the final obtained porous alumina ceramic decreased accordingly from 57.4 MPa to 17.7 MPa.     

Bonding of novel self-glazed zirconia dental ceramics

ABSTRACT

Bonding behaviours of a novel self-glazed zirconia dental material were investigated. The effect of a preformed porous nanoceramic bonding surface and the different cleansing methods on saliva-contaminated bonding surfaces was assessed in this in vitro study. Cleaning procedures commonly used in dental offices were tested. All specimens demonstrated adhesive fracture patterns except for airborne particle abrasion group, which resulted in mixed-type fracture pattern and the highest bonding force values. No statistically significant differences in bonding force values were found between self-glazed zirconia with and without a preformed porous nanoceramic bonding surface when bonded with the self-adhesive resin cement (RelyX? Unicem 2). Scanning electron micrographs revealed no interaction between the bonding surface and the resin cement after priming. Mechanical retention is the predominant bonding mechanism between the bonding surface and the luting resin cement.     

Porous SiC/SiCN composite ceramics fabricated by foaming and reaction sintering

Porous SiC/SiCN composite ceramics with heterogeneous pore structure and rod-like SiCN grains were fabricated by foaming and reaction sintering. The mixture slurry containing SiC and silicon as raw materials, cornstarch as binder, Y₂O₃ as sintering additive and an electrosteric dispersant was stirred with foams derived from pre-foaming using foaming agent. The casted green body was sintered at 1650 °C under nitrogen atmosphere. The results demonstrated that the porous SiC/SiCN ceramics exhibited hierarchical vias ranging from 1 μm to 1 mm and the rod-like crystalline SiCN grains generated in the SiC matrix.     

Fabrication and properties of SiC porous ceramics using a polyurethane preparation process

SiC porous ceramics can be prepared by introducing the polyurethane preparation method into the production process of ceramic biscuits, followed by sintering at 1300?°C for 2?h under N₂ flux after the cross-linking of polycarbosilane at 220?°C for 4?h in air. The microstructures, mechanical properties and infiltrations of the SiC porous ceramics are investigated in detail. The best dispersal effect comes from the SiC slurry with xylene as the solvent and a mixture of Silok®7096 (1?wt%) and Anjeka®6041 (4?wt%) as the dispersant. The compressive strength of SiC porous ceramics with high porosity (69.53%) reaches 16.9?MPa. The heat treatment can increase infiltration, the rate of which (4.296?×?10^?7 mm²) after the heat treatment at 750?°C in air is approximately two times faster than that before the heat treatment. The SiC porous ceramics fabricated in this study will have potential application in active thermal protection systems.