Phase Transition and Ferroelectric Characteristics of Pb[(Mg1/3Nb2/3)1-xTix]O3 Ceramics Modified with La(Mg2/3Nb1/3)O3

The effects of 0–5 mol% addition of La(Mg_2/3Nb_1/3)O₃ (LMN) on the phase transition and ferroelectric behaviors of Pb[(Mg_1/3Nb_2/3)_1-xTi_x]O₃ (PMNT) ceramics with compositions near the morphotropic phase boundary (MPB) were studied. An evolution of structure from rhombohedral to tetragonal was found with increasing PbTiO₃ (PT) content across the MPB (at ∼32.5 mol% PT), and a coexistence of both rhombohedral and tetragonal phases was also found at the MPB. The dual-phase field extended toward the lower PT content side of the MPB, and, moreover, the rhombohedrality or tetragonality was reduced, especially for the compositions near the MPB, by the addition of La in PMNT. The ferroelectric transition was found to change from normal to diffuse as the La content increased and the compositions became more rhombohedral. In accordance with the structural evolution, the change of remanent polarization ( P _r) and coercive field ( E _c) also became gradually indistinct, and both P _r and E _c were reduced. For compositions near the MPB, both PMNT and La-modified PMNT had a similar electromechanical factor ( k _p) in a range around 0.55–0.60, but the mechanical quality factor ( Q _m) was significantly reduced for the La-modified PMNT. The piezoelectric coefficient ( d ₃₃), however, was largely improved with increasing La content in PMNT of compositions at MPB. A high value of d ₃₃∼ 815 pC/N was obtained for the 5-mol%-La-modified ceramics, but it was associated with a low value of Q _m.     

Phase Relations in the Na0.5Bi0.5TiO3–Li3xLa(2/3)−x□(1/3)−2xTiO3 System

The phase relations and the mechanism of solid-state synthesis for the Na_0.5Bi_0.5TiO₃–Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} TiO₃ system were investigated using X-ray powder diffraction, scanning electron microscopy, and thermal analysis. The study revealed that the extent of the homogeneity range—which is related to the A-site substitution between (Na_0.5Bi_0.5)²⁺ and (Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} )²⁺ pseudo cations of a perovskite structure—depends strongly on the ordering of the (Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} )²⁺ species. The solid-state reaction of the compounds in the homogeneity range is completed only after multiple high-temperature firings. However, the system is also subjected to a slow thermal decomposition; this is particularly so for the compounds with a high × value and an increased Li_{3 x} La_{(2/3)− x} □_{(1/3)−2 x} TiO₃ concentration.     

Synthesis of Compositionally Homogeneous Sr(CuxZn1−x)1/2W1/2O3

A complex perovskite of Sr(Cu _x Zn_{1- x} )_1/2 W_1/2O₃ (SCZW) is synthesized by a new combination of wet and dry processess. Mixed oxides containing Cu²⁺ and Zn²⁺ (CZ) are prepared by the wet process (coprecipitate method). SCZW is obtained by the dry process (mixed-oxide method) from a mixture of CZ, SrCO₃, and WO₃. SCZW has practically no compositional, unlike solid solutions prepared by the conventional dry method. The wet–dry process method is useful because the wet process is applied to only B-site cations having the same valence.     

Ta2O5/Nb2O5 and Y2O3 Co-doped Zirconias for Thermal Barrier Coatings

Zirconia doped with 3.2–4.2 mol% (6–8 wt%) yttria (3–4YSZ) is currently the material of choice for thermal barrier coating topcoats. The present study examines the ZrO₂-Y₂O₃-Ta₂O₅/Nb₂O₅ systems for potential alternative chemistries that would overcome the limitations of the 3–4YSZ. A rationale for choosing specific compositions based on the effect of defect chemistry on the thermal conductivity and phase stability in zirconia-based systems is presented. The results show that it is possible to produce stable (for up to 200 h at 1000°–1500°C), single (tetragonal) or dual (tetragonal + cubic) phase chemistries that have thermal conductivity that is as low (1.8–2.8W/m K) as the 3–4YSZ, a wide range of elastic moduli (150–232 GPa), and a similar mean coefficient of thermal expansion at 1000°C. The chemistries can be plasma sprayed without change in composition or deleterious effects to phase stability. Preliminary burner rig testing results on one of the compositions are also presented.     

XRD and Raman Studies on the Ordering/Disordering of Ba(Mg1/3Ta2/3)O3

The samples of complex perovskite Ba(Mg_1/3Ta_2/3)O₃ (BMT) were synthesized at various sintering temperatures and the X-ray diffraction (XRD) patterns and Raman spectra of the samples were collected. Both the structure refinements using the XRD data and the Raman spectra show that the samples sintered above 1500°C with high pellet relative density (>95%) take almost-perfect B-site-ordered structure; while the samples sintered below 1400°C with low pellet relative density (<70%) take the more disordered structure at B-sites. The vibrational modes of 1:2 ordered BMT     were obtained and illustrated by using first-principle calculations. With the assistance of the calculation results, Raman peaks of BMT were assigned as A _1g(1) (107 cm⁻¹), A _1g(2) (212 cm⁻¹), A _1g(3) (433 cm⁻¹), A _1g(4) (798 cm⁻¹), and E _g(1) (104 cm⁻¹), E _g(2) (160 cm⁻¹), E _g(3) (264 cm⁻¹), E _g(4) (386 cm⁻¹), E _g(5) (576 cm⁻¹). The highly ordered BMT sample at B-site shows longer phonon lifetime and weaker coupling among phonons than the disordered BMT, which probably are the intrinsic reasons for the highly ordered BMT sample to have the low dielectric loss.     

Dielectric and Piezoelectric Properties of Pb(Co1/3Nb2/3)O3-PbTiO3-PbZrO3 Solid Solution Ceramics

Ceramic and piezoelectric properties of the Pb(Co_1/3Nb_2/3)O₃-PbTiO₃-PbZrO₃ system were investigated. The system contains rhombohedral, tetragonal, and pseudocubic phases at room temperature. The triple point is at 0.07Pb(Co_1/3Nb_2/3)O₃-0.43PbTiO₃-0.50PbZrO₃. High dielectric constants (750 to 1500) and radial coupling coefficients (40 to 45%) and low average temperature coefficients of resonant frequency (of the order of 10^-6°C) were obtained for compositions near the morphotropic phase boundary.     

Topotaxy between BaTiO3 and Ba6Ti17O40

The orientational relationship between intergrown lamellae of tetragonal (t) BaTiO₃ and monoclinic (m) Ba₆Ti₁₇O₄₀ was found to be ( 1 1 1 )_t||(001)_m, (001)_t||( 1 0 1 )_m, and [110]_t||[0 1 0]_m. On the basis of this relationship a model of a topotactic boundary between these two phases was constructed.     

Dielectric-State Analysis in Solid-Solution Pb(Yb1/2Ta1/2)O3–Pb(Lu1/2Nb1/2)O3

The structure and temperature dependence of complex lead perovskite dielectrics were investigated for the system (1 − x )Pb(Yb_1/2Ta_1/2)O₃– x Pb(Lu_1/2Nb_1/2)O₃. Superlattice reflections for the compositions 0.8 < x < 1.0 were observed by X-ray diffractometry, and the temperature-composition dielectric-state diagram was determined. In the present study, the disordered middle composition, with 0.2 < x < 0.8, showed a diffuse paraelectric–ferroelectric phase transition, whereas the ordered end compositions, with 0 ≤ x < 0.2 and 0.8 < x ≤ 1.0, revealed successive sharp paraelectric–antiferroelectric and weak antiferroelectric–ferroelectric phase transitions. The dielectric state was confirmed by examining the variation of polarization ( P ) with electric field ( E ).     

Cation Ordering Transformations in the Ba(Zn1/3Nb2/3)O3-La(Zn2/3Nb1/3)O3 System

Single-phase perovskites were formed in the (1−_x)Ba(Zn_1/3Nb_2/3)O₃-( _x )La(Zn_2/3Nb_1/3)O₃ system for compositions with 0.0≤ x ≤0.6. Although the stability of the trigonal "1:2" ordered structure of the Ba(Zn_1/3Nb_2/3)O₃ end member is very limited (0.0≤ x ≤0.05), low levels of lanthanum induce a transformation to a cubic, "1:1" ordered structure that has a broad range of homogeneity (0.05≤ x ≤0.6). Samples with x > 0.6 were comprised of La₃NbO₇, ZnO, and a perovskite with x = 0.6. The cubic 1:1 phases were fully ordered and no evidence was found for a compositionally segregated microstructure. These observations could not be reconciled in terms of a "space-charge" model; rather, they supported a charge-balanced, "random-site" structure for the 1:1 cation-ordered Ba(β_1/2'β_1/2")O₃ phases.     

Hot Forging Characteristics of Fine-Grained ZrO2 and Al2O3/ZrO2 Ceramics

Preliminary results indicate that large strains (∼80%) and strain rates (0.001 s⁻¹) can be obtained without tearing (or cracking) in fine-grain ZrO₂ (0.3 μm) and Al₂O₃/ZrO₂ (1 μm) ceramics. Alumina develops crystallographic and morphological texture as previously reported by Heuer et al.¹     

Sol-Gel Route to Ferroelectric Layer-Structured Perovskite SrBi2Ta2O9 and SrBi2Nb2O9 Thin Films

Precursors for layer-structured perovskite thin films of SrBi₂Ta₂O₉ (SBT) and SrBi₂Nb₂O₉ (SBN) were prepared by the reactions of a strontium-bismuth double methoxyethoxide and tantalum or niobium methoxyethoxide in methoxyethanol, followed by partial hydrolysis. Several spectroscopic techniques, such as ¹H-, ¹³C-, and ⁹³Nb-NMR (nuclear magnetic resonance), and Fourier-transform infrared spectroscopy were used to analyze the arrangement of the metals and oxygen in the precursor molecules. The precursors contained Sr-O-M (where M is Ta or Nb) bonds (i.e., a strontium is connected to two MO₆ octahedra) and Sr-O-Bi bonds with a bismuth atom bonded to the oxygens of the MO₆ octahedron. The arrangement of metals and oxygens was considered to be similar to the layer-structured perovskite crystal sublattice. As a result, the sol-gel-derived SBT thin films crystallized, by rapid thermal annealing in an oxygen atmosphere below 550°C, and they exhibited preferred (115) orientation. The crystallinity improved and the crystallite size increased with temperature up to 700°C. In the case of SBN thin films, a low heating rate (2°C/min) was necessary for the control of the crystallographic (115) orientation, whereas a rate of 200°C/s (rapid thermal annealing) produced films that exhibited c -axis orientation. The (115) SBT thin film, heated to 700°C, exhibited improved ferroelectric properties.     

High-Temperature Structural Phase Transition in Ca0.7Ti0.7La0.3Al0.3O3: Investigation by Synchrotron X-Ray Diffraction

Mixed-oxide prepared Ca_0.7Ti_0.7La_0.3Al_0.3O₃ (CTLA) ceramics (≈96% dense), grain size 6–7 μm, with dielectric properties (at 4 GHz) of ɛ_r≈46, Q × f ≈38 000 GHz, and τ_f+13 ppm/°C, were studied at 25°–1300°C using synchrotron X-ray powder diffraction. At room temperature, CTLA exhibits a distorted orthorhombic structure, with two tilt systems: a =5.40383 (4) Å, b =5.41106 (6) Å, and c =7.64114 (7) Å with space group Pbnm . At 1050°±25°C, there is a transition from orthorhombic ( Pbnm ) to tetragonal ( I 4/ mcm ), with a simpler tilt arrangement. The lattice parameters at 1100°C were: a =5.44285 (4) Å and c =7.68913 (8) Å.     

The System HfO2-Y2O3-Er2O3

A mathematical model of the liquidus surface based on a reduced polynomial method was proposed for the system HfO₂-Y₂O₃-Er₂O₃. The results of calculations according to this model agree fairly well with the experimental data. Phase equilibria in the system HfO₂-Y₂O₃-Er₂O₃ were studied on melted (as-cast) and annealed samples using X-ray diffraction (at room and high temperatures) and micro-structural and petrographic analyses. The crystallization paths in the system HfO₂-Y₂O₃-Er₂O₃ were established. The system HfO₂-Y₂O₃-Er₂O₃ is characterized by the formation of extended solid solutions based on the fluorite-type (F) form of HfO₂ and cubic (C) and hexagonal (H) forms of Y₂O₃ and Er₂O₃. The boundary curves of these solid solutions have the minima at 2370°C (15. 5 mol% HfO₂, 49. 5 mol% Y₂O₃) and 2360°C (10. 5 mol% HfO₂, 45. 5 mol% Y₂O₃). No compounds were found to exist in the system investigated.     

Processing and Electrical Properties in Lead-Based (Pb(Mg1/3Nb2/3)O3, Pb(Yb1/2Nb1/2)O3, PbTiO3) Systems

Lead-based ferroelectric (FE) ceramics exhibit superior electromechanical properties; therefore, there has been an increased focus on developing new lead-based FE materials with high Curie temperature ( T _c) and enhanced properties. The aim of this study was to investigate new compositions in the Pb(Mg_1/3Nb_2/3)O₃–Pb(Yb_1/2Nb_1/2)O₃–PbTiO₃ ( PMN–PYbN–PT) system to enhance the electromechanical properties while increasing the T _c and lowering the sintering temperature. The 0.575[0.5PMN–0.5PYbN]–0.425PT composition at PMN/PYbN (50/50) mole ratio were prepared by reactive sintering PMNT and PYbNT powder mixtures at 950°–1200°C for 4 h. PMNT and PYbNT powders were calcined via the columbite method. Samples were prepared by cold isostatic pressing at 80 MPa. Dense and fully perovskite 0.575[0.5PMN–0.5PYbN]–0.425PT ceramics were fabricated at 975°C for 4 h, and these samples displayed a remnant polarization ( P _r) of 32 μ C/cm², coercive field ( E _c) of 17 kV/cm, and a piezoelectric charge coefficient ( d ₃₃) of 475 pC/N. It is proposed that this ternary system can be tailored for various applications.     

Photoluminescence Characteristics of Energy Transfer Between Eu3+and Bi3+in LiEu1−xBix (WO4)0.5(MoO4)1.5

A series of novel red phosphors LiEu_{1− x} Bi _x (WO₄)_0.5(MoO₄)_1.5 ( x =0, 0.05, 0.10, 0.15, 0.20, 0.30, 0.40, and 0.50) were synthesized by the conventional solid-state reaction method. The spectrum and the crystal structure of the phosphors were characterized by Fluorescence spectrophotometry and X-ray diffraction, respectively. The photoluminescent results show that all samples can be excited efficiently by UV (396 nm) and blue (467 nm) light and that they emit red light at 615 nm with line spectra, which are coupled well with the characteristic emissions from UVLED and blue light-emitting diode (LED), respectively. There is an efficient energy transfer from Bi³⁺ to Eu³⁺ ions, leading to the emission intensity of Eu³⁺ being enhanced by 1.5 times, and even more when Bi³⁺ ions are introduced into LiEu (WO₄)_0.5(MoO₄)_1.5. The introduction of Bi³⁺ ions broadened the excitation band of the phosphor, and the optimum doping concentration is found to be 10 mol% of Bi³⁺.     

Crystal Structure and Microwave dielectric Properties of Ba(Zn1/3Ta2/3)O3–(Sr,Ba)(Ga1/2Ta1/2)O3 Ceramics

The microwave dielectric properties and crystal structure of Ba(Zn_1/3Ta_2/3)O₃– (Sr,Ba)(Ga_1/2Ta_1/2)O₃ ceramics were investigated in the present study. The Q value of Ba(Zn_1/3Ta_2/3)O₃ was improved by adding 5 mol% Sr(Ga_1/2Ta_1/2)O₃. The maximum Q value of Q × f = 162000 GHz was obtained at 0.95Ba(Zn_1/3Ta_2/3)O₃. 0.05Sr(Ga_1/2Ta_1/2)O₃. For this composition, a lattice super structure caused by hexagonal ordering was observed. A further improvement in the Q value was attained when some Sr was replaced with Ba, and 0.95Ba(Zn_1/3Ta_2/3)O₃· 0.05(Sr_0.25Ba_0.75)(Ga_1/2Ta_1/2)O₃ exhibited a maximum Q value such that Q × f = 210000 GHz. Despite the increased Q value with the replacement of Sr by Ba, the c/a value, which indicates the degree of lattice distortion, remained constant near 3/2. The Q value thus improved without lattice distortion in the system Ba(Zn_1/3Ta_2/3)O₃-(Sr,Ba)(Ga_1/2Ta_1/2)O₃, whereas the improvement of Q value increased with lattice distortion in the solid solution system with Ba(Zn_1/3Ta_2/3)O₃ as an end member.     

Effect of Extrusion on the Critical Current Density of Bi1.4Pb0.6Sr2Ca2Cu3Ox Superconducting Wires

The effect of extrusion on improving the critical current density ( J _c) of Bi_1.4Pb_0.6Sr₂Ca₂Cu₃O _x superconducting wires is investigated. Calcined powders (Bi_1.4Pb_0.6Sr₂Ca₂Cu₃O _x ) are first mixed with a forming aid—a thermoplastic polymer (polyethylene)—for workability, and then extruded, using a capillary rheometer, to form wires 2 mm in diameter. The J _c value, measured by the four-probe method in liquid nitrogen at 77 K, is improved substantially by the following process: (1) the superconducting precursors are extruded at high viscosity with a forming aid, to align the platelike particles unidirectionally; (2) the forming aid alone is carefully burned out, without destroying the extruded configuration; and (3) the extruded wires are annealed at 850°C in air for more than 96 h.     

Structure and Dielectric Properties of Pb(Sc2/3W1/3)O3–Pb(Zr/Ti)O3 Relaxors

The structure and dielectric properties of (1− x )Pb(Sc_2/3W_1/3)O₃–( x )Pb(Zr/Ti)O₃ ceramics have been investigated over a full substitution range. All compositions with x < 0.5 adopt a cubic perovskite structure; however, for x ≤ 0.25 a doubled cell results from a 1:1 ordered distribution of the B-site cations. The structural order in Pb(Sc_2/3W_1/3)O₃ (PSW) can be described by a random-site model with one cation site occupied by Sc³⁺ and the other by a random distribution of (Sc_1/3³⁺W_2/3⁶⁺). The ordering is destabilized in solid solutions of PSW with PbZrO₃ (PSW–PZ), but stabilized by PbTiO₃ in the (1− x )PSW–( x )PT system. The changes in order are accompanied by alterations in the dielectric response of the two systems. For PSW–PZ the temperature of the permittivity maximum ( T _ɛ,max) increases linearly with x ; however, for PSW–PT T _ɛ,max decreases in the ordered region (up to x = 0.25) and then increases rapidly as the order is lost. Similar effects were produced by modifying the degree of order of (0.75)PSW–(0.25)PT; when the order parameter was reduced from ∼1.0 to ∼0.65, T _ɛ,max increased by more than 60°C.     

Electromechanical Properties of Pb(Yb1/2Nb1/2)O3-PbZrO3-PbTiO3 Ceramics

The electromechanical and electric-field-induced strain properties of x Pb(Yb_1/2Nb_1/2)O₃· y PbZrO₃·(1− x − y )PbTiO₃ ( x = 0.12, 0.25, 0.37; y = 0.10–0.40) ceramics have been studied systematically as a function of Pb(Yb_1/2Nb_1/2)O₃ (PYN) content and PbZrO₃/PbTiO₃ (PZ/PT) ratio. In addition, the effect of MnO₂ on the electromechanical properties of 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ was also investigated. The maximum transverse strain values of 1.6 × 10⁻³ for x = 0.12, 1.45 × 10⁻³ for x = 0.25, and 1.36 × 10⁻³ for x = 0.37 were obtained at the compositions which were regarded as the morphotropic phase boundary (MPB). The transverse strain was maximized at the MPB composition. The value of the maximum electromechanical coupling coefficient was 0.69 for y = 0.40 and x = 0.12 composition. In the 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ composition, the temperature of the maximum dielectric constant decreased and the grain size increased with an addition of MnO₂. The electromechanical coupling coefficient decreased while the mechanical quality factor rapidly increased with an addition of MnO₂. These resulted mainly from the acceptor effect of manganese ions that were produced by doping MnO₂ into the perovskite structure.     

Fabrication of Na0.5Bi0.5TiO3–BaTiO3-Textured Ceramics Templated by Plate-Like Na0.5Bi0.5TiO3 Particles

Textured 0.94Na_0.5Bi_0.5TiO₃–0.06BaTiO₃ (NBT–6BT) ceramics were fabricated by templated grain growth (TGG) using anisotropically shaped Na_0.5Bi_0.5TiO₃ (NBT) templates. Platelet NBT was synthesized by the topochemical technique, using precursor Na_0.5Bi_4.5Ti₄O₁₅ (NBIT). The NBT particles have an average length of 10–15 μm and a thickness of 1 μm, which are suitable templates for obtaining textured ceramics (especially NBT-based ceramics) by the TGG process. This study revealed that the NBT templates are effective in inducing grain orientation in NBT–6BT ceramics. For NBT–6BT ceramics textured with 5 vol% NBT templates, a Lotgering factor of 0.87 and a d ₃₃ of 299 pC/N are given.