Structural and optical properties of Er-doped Y2Ti2O7 thin films by sol-gel method

Er³⁺-doped Y₂Ti₂O₇ and Er₂Ti₂O₇ thin films were fabricated by sol-gel spin-coating method. A well-defined pyrochlore phase Er_xY_2-xTi₂O₇ was observed while the annealing temperature exceeded 800 °C. The average transmittance of the Er_xY_2-xTi₂O₇ thin films annealed at 400 to 900 °C reduces from ∼ 87 to ∼ 77%. The refractive indices and optical band gaps of Er_xY_2-xTi₂O₇ (x = 0-2) annealed at 800 °C/1 h vary from 2.20 to 2.09 and 4.11 to 4.07 eV, respectively. The ∼ 1.53 μm photoluminescence spectrum of Er³⁺ (5 mol%)-doped Y₂Ti₂O₇ thin films annealed at 700 °C/1 h exhibits the maximum intensity and full-width at half maximum (∼ 60 nm).     

Order-disorder phase transitions and high-temperature oxide ion conductivity of Er2+xTi2−xO7−δ (x = 0, 0.096)

The Er_2+xTi_2−xO_7−δ (x = 0.096; 35.5 mol% Er₂O₃) solid solution and the stoichiometric pyrochlore-structured compound Er₂Ti₂O₇ (x = 0; 33.3 mol% Er₂O₃) are characterized by X-ray diffraction (phase analysis and Rietveld method), thermal analysis and optical spectroscopy. Both oxides were synthesized by thermal sintering of co-precipitated powders. The synthesis study was performed in the temperature range 650-1690 °C. The amorphous phase exists below 700 °C. The crystallization of the ordered pyrochlore phase (P) in the range 800-1000 °C is accompanied by oxygen release. The ordered pyrochlore phase (P) exists in the range 1000−1200 °C. Heat-treatment at T ≥ 1600 °C leads to the formation of an oxide ion-conducting phase with a distorted pyrochlore structure (P2) and an ionic conductivity of about 10⁻³ S/cm at 740 °C. Complex impedance spectra are used to separately assess the bulk and grain-boundary conductivity of the samples. At 700 °C and oxygen pressures above 10⁻¹⁰ Pa, the Er_2+xTi_2−xO_7−δ (x = 0, 0.096) samples are purely ionic conductors.     

Composition dependence of structural and optical properties of Ba(Zrx,Ti1-x)O3 thin films grown on MgO substrates by pulsed laser deposition

Ba(Zr_x,Ti_1-x)O₃ (BZT) films with Zr concentration ranging from 0 to 40% were grown on MgO single crystal substrates by pulsed laser deposition, and their optical properties in the visible range were systematically characterized. A linear increase in the out-of-plane lattice constant of BZT unit cell with increasing Zr content was detected by X-ray diffraction. The surface morphology was observed by atomic force microscopy and the grain size was shown to increase with Zr concentration. Prism coupling and UV-visible transmission spectroscopy techniques were used to analyze the optical properties of the films. Refractive index between 2.15 and 2.3 was observed at 633 and 1547 nm respectively, which decreased with rising Zr content. The BZT films also possessed large optical band gap energy up to 3.92 eV, which increased with rising Zr content. Quadratic electro-optic effect was observed with electro-optic coefficients between 0.11 and 0.81 × 10^− 18 m²/V², which decreased with Zr concentration. Optical loss was estimated from scattering and absorption, and the absorption coefficient dropped with increasing Zr content at near band gap. The obtained results provide information for the design of BZT thin film-based optical devices.     

Phase stabilization and microstructural studies of lead lanthanum titanate thin films

Thin ferroelectric films of PLTx (Pb_1−xLa_xTi_1−x/4O₃) have been prepared by a sol-gel spin coating process. As deposited films were thermally treated for crystallization and formation of perovskite structure. Characterization of these films by X-ray diffraction (XRD) have been carried out for various concentrations of La (x = 0.04, 0.08 and 0.12) on ITO coated corning glass substrates. For a better understanding of the crystallization mechanism, the investigations were carried out on films annealed at temperatures (350, 450, 550 and 650 °C). Characterization of these films by X-ray diffraction shows that the films annealed at 650 °C exhibit tetragonal phase with perovskite structure. Atomic force microscope (AFM) images are characterized by slight surface roughness with a uniform crack free, densely packed structure. Fourier transform infrared spectra (FTIR) studies of PLTx thin films (x = 0.08) deposited on Si substrates have been carried out to get more information about the phase stabilization.     

Laser-induced amorphization and crystallization on Se80Te20−xPbx thin films

Thin films of glassy alloys of a-Se₈₀Te_20−xPb_x (x=2, 6 and 10) was crystallized in a specially designed sample holder under a vacuum of 10⁻² Pa. The amorphous and crystallized films were induced by pulse laser (wavelength: 337.1 nm, frequency: 10 Hz, pulse duration: 4 ns and pulse energy: 0.963 mJ). After laser irradiation on amorphous and crystalline films: optical band gaps were measured. Crystallization and amorphization of chalcogenide films is accompanied by the change in the optical band gap. The change in optical energy gap could be determined by identification of the transformed phase. This change in the optical band gap may be due to the increase in the grain size and the reduction in the disorder of the system.     

Electrochromic performance of mixed V2O5–MoO3 thin films synthesized by pulsed spray pyrolysis technique

Mixed V₂O₅–MoO₃ thin films were deposited onto the glass and fluorine doped tin oxide (FTO) coated glass substrates, at 400 °C by pulsed spray pyrolysis technique (PSPT). Equimolar vanadium chloride (VCl₃) and ammonium molybdate aqueous solutions were mixed together in volume proportions (5–15% molybdenum) and used as a precursor solution for the deposition of mixed V₂O₅–MoO₃ thin films. The structural, morphological, optical and electrochromic properties of the films deposited at different Mo concentrations were studied. With increase in the percentage of Mo the peaks belonging to tetragonal phase of V₂O₅ eventually disappear and the (1 0 1) orthorhombic V₂O₅ phase is observed. Scanning electron microscopy (SEM) shows micro thread like reticulated morphology. The optical band gap energy varied over 2.91–2.85 eV. All the films exhibited cathodic electrochromism in lithium containing electrolyte (0.5 M LiClO₄ + propylene carbonate (PC)). The highest coloration efficiency (CE) for the V₂O₅ film with 15% MoO₃ mixing was found 35.27 cm² C⁻¹.     

V-doping effects on ferroelectric properties of K0.5Bi4.5Ti4O15 thin films

V-doped K_0.5Bi_4.5Ti₄O₁₅ (K_0.5Bi_{4.5 − x/3}Ti_4 − xV_xO₁₅, KBTiV-x, x = 0.00, 0.01, 0.03, and 0.05) thin films were prepared on a Pt(111)/Ti/SiO₂/Si(100) substrate by a chemical solution deposition method. The thin films were annealed by using a rapid thermal annealing process at 750 °C for 3 min in an oxygen atmosphere. Among them, KBTiV-0.03 thin film exhibited the most outstanding electrical properties. The value of remnant polarization (2P_r) was 75 μC/cm² at an applied electric field of 366 kV/cm. The leakage current density of the thin film capacitor was 5.01 × 10⁻⁸ at 100 kV/cm, which is approximately one order of magnitude lower than that of pure K_0.5Bi_4.5Ti₄O₁₅ thin film capacitor. We found that V doping is an effective method for improving the ferroelectric properties of K_0.5Bi_4.5Ti₄O₁₅ thin film.     

Investigation on structural, electrical and optical properties of tungsten-doped tin oxide thin films

Tungsten-doped tin oxide (SnO₂:W) transparent conductive films were prepared on quartz substrates by pulsed plasma deposition method with a post-annealing. The structure, chemical states, electrical and optical properties of the films have been investigated with tungsten-doping content and annealing temperature. The lowest resistivity of 6.67 × 10^− 4 Ω cm was obtained, with carrier mobility of 65 cm² V^− 1 s^− 1 and carrier concentration of 1.44 × 10²⁰ cm^− 3 in 3 wt.% tungsten-doping films annealed at 800 °C in air. The average optical transmittance achieves 86% in the visible region, and approximately 85% in near-infrared region, with the optical band gap ranging from 4.05 eV to 4.22 eV.     

Studying trivalent/bivalent metal ion doped TiO2 as p-TiO2 in bipolar heterojunction devices

Trivalent/bivalent metal ions doped TiO₂ thin films (M_xTi_1−xO₂, M = Cr³⁺, Fe³⁺, Ni²⁺, Co²⁺, Mn²⁺ and x = 0.01, 0.05, 0.1, 0.15, 0.2) were deposited on Indium–tin oxide (ITO) coated glass substrates by spin coating technique. X-ray photoelectron spectroscopy (XPS) showed Ti⁴⁺ oxidation state of the Ti2p band in the doped p-TiO₂. The homogenous M_xTi_1−xO₂ was used to support n-ZnO thin films with thickness ∼40–80 nm and vertically aligned n-ZnO nanorods (NR) with length ∼300 nm and 1.5 μm. Current (I)–voltage (V) characteristics for the Ag/n-ZnO/M_xTi_1−xO₂/ITO/glass assembly showed rectifying behavior with small turn-on voltages (V₀) < 1 V. The ideality factor (η) and the resistances in both forward and reverse bias were calculated. The temperature dependence performance of these bipolar devices was performed and variation of the parameters with temperature was studied.     

Ohmic contacts and n-type doping on TixCr2 − xO3 films and the temperature dependence of their transport properties

A procedure to dope n-type Cr_2 − xTi_xO₃ thin films is proposed. Besides doping the material, at the same time the method forms ohmic contacts on Ti_xCr_2 − xO₃ films. It consists on the deposition of 10 nm Ti and 50 nm Au, followed by thermal annealing at 1000 °C for 20 min in N₂ atmosphere. Ohmic contacts were formed on three samples with different composition: x = 0.17, 0.41 and 1.07 in a van der Pauw geometry for Hall effect measurements. These measurements are done between 35 K and 373 K. All samples showed n-type nature, with a charge carrier density (n) on the order of 10²⁰ cm^− 3, decreasing as x increased. As a function of temperature, n shows a minimum around 150 K, while the mobilities have an almost constant value of 11, 28 and 7 cm²V^− 1 s^− 1 for x = 0.17, 0.41 and 1.07, respectively.     

The properties of transparent semiconductor Zn1 − xTixO thin films prepared by the sol-gel method

Transparent semiconductor thin films of Zn_1 − xTi_xO (0 ≦ x ≦ 0.12) were deposited on alkali-free glass substrates by the sol-gel method. The effects of Ti addition on the crystallization, microstructure, optical properties and resistivity of ZnO thin films were investigated. The as-coated films were preheated at 300 °C, and then annealed at 500 °C in air ambiance. X-ray diffraction results showed all polycrystalline Zn_1 − xTi_xO thin films with preferred orientation along the (002) plane. Ti incorporated within the ZnO thin films not only decreased surface roughness but also increased optical transmittance and electrical resistivity. In the present study, the Zn_0.88Ti_0.12O film exhibited the best properties, namely an average transmittance of 91.0% (an increase of ~ 12% over the pure ZnO film) and an RMS roughness value of 1.04 nm.     

Optical properties of CdxZn(1−x)O films deposited by ultrasonic spray pyrolysis method

Cd_xZn_(1−x)O (x = 0, 0.59, 0.78 and 1) films have been produced by ultrasonic spray pyrolysis technique using aqueous solutions of CdCl₂ H₂O and ZnCl₂ on the microscope glass substrate between 325 and 400 °C. The Cd_xZn_(1−x)O samples have been crystallized both cubic and hexagonal structures. The optical properties of the samples were characterized by transmittance and absorption spectroscopy measurements. Transmissions of the samples have decreased with increasing x values. The optical band gap energies of the Cd_xZn_(1−x)O samples from the absorption spectra have been calculated between 2.48 and 3.23 eV by different Zn contents. The samples were annealed at 350 and 450 °C. The optical band gap energy has decreased at 350 °C whereas it increased at 450 °C.     

Microfabrication of dilute magnetic semiconducting Ti1−xCoxO2 films using photosensitive sol-gel method

Photosensitive Ti_1−xCo_xO₂ gel films are prepared by chemical modification with benzoylacetone, and then their Fourier transform infrared spectra and ultraviolet visible spectra are measured. Results show that the chelate rings of benzoylacetone with Ti ions are formed in the Ti_1−xCo_xO₂ gel films. With irradiation of UV light, the chelate rings are photolyzed, which leads to a change of the solubility of the Ti_1−xCo_xO₂ gel films in methanol. Based on this, the micro-patterns of Ti_1−xCo_xO₂ gel films are obtained. After the patterned gel films are dried at 200 °C and are fired at 550 °C for 1 h, negative patterned Ti_1−xCo_xO₂ inorganic films are obtained. The Ti_1−xCo_xO₂ films have an anantase structure and exhibit a room temperature ferromagnetic property.     

Y0.08Sr0.92FexTi1−xO3−δ perovskite for solid oxide fuel cell anodes

A single phase perovskite Y_0.08Sr_0.92Fe_xTi_1−xO_3−δ (x = 0.05, 0.1,0 0.20, 0.25, 0.40, and 0.50) was fabricated at 1400 °C in air by a solid state reaction method and its electrical conductivity and electrochemical properties as an anode were investigated as a function of the Fe content. Doping with Y for Sr allowed the SrFe_xTi_1−xO_3−δ perovskite to be stable at 800 °C in a reducing atmosphere. At 900 °C, metallic Fe precipitated and the stability of the perovskite phase under a reducing atmosphere decreased as the Fe content increased. The conductivity of Y_0.08Sr_0.92Fe_xTi_1−xO_3−δ (x = 0.40) was greater than that of the x = 0.20 sample. The conductivity of Y_0.08Sr_0.92Fe_xTi_1−xO_3−δ was found to be 2 × 10⁻¹ Scm⁻¹ at 800 °C in H₂. Sintering the Y_0.08Sr_0.92Fe_xTi_1−xO_3−δ anode at 1200 °C was found to be optimum to obtain not only good interfacial adhesion, but also a fine grain structure. The Y_0.08Sr_0.92Fe_0.25Ti_0.75O_3−δ anode exhibited the lowest polarization resistance (0.7 and 1.8 Ωcm² at 800 and 700 °C).     

Preparation and characterization of highly (1 1 1)-oriented (Pb,La)(Zr,Ti)O3 thin films by sol-gel processing

Lanthanum modified lead zirconate titanate (Pb_0.91La_0.09)(Zr_0.65Ti_0.35)O₃ (PLZT) ferroelectric thin films were grown on Pt/Ti/SiO₂/Si(1 0 0) and fused quartz substrates using a sol-gel method with rapid thermal annealing processing. The results showed that the highly (1 1 1)-oriented pervoskite PLZT thin film growth on Pt/Ti/SiO₂/Si(1 0 0) substrates. The electrical measurements were conducted on PLZT films in metal-ferroelectric-metal capacitor configuration. The PLZT thin films annealed at 600 °C showed well-saturated hysteresis loops with remanent polarization and coercive electric field values were 10.3 μC/cm² and 36 kV/cm, respectively, at an applied field of 300 kV/cm. At 100 kHz, the dielectric constant and dielectric loss of the film are 682 and 0.021, respectively. The PLZT thin film on fused quartz substrate, annealed at 600 °C, exhibited good optical transmittance, the band gap of optical direct transitions is 3.89 eV.     

Optical and electrical properties of heat-resistant Sb-doped Sn1 − xHfxO2 transparent conducting films

To examine variations in the transparent conducting properties after annealing at high temperatures, 300-nm thick Sb-doped Sn_1 − xHf_xO₂ (x = 0.00-0.10) films were deposited onto silica glass substrates by the RF sputtering method and annealed in air up to 1000 °C at 200 °C increments. After annealing, all the Sb-doped SnO₂ films were transparent and electrically conductive, but large cracks, which decreased the electrical conductivity, were generated in several films due to crystallization or the thermal expansion difference between the film and substrate. Only the film deposited at room temperature in an Ar and O₂ mixed atmosphere did not crack after annealing, and its electrical conductivity exceeded 100 S cm^− 1 even after annealing at 1000 °C in air. Hf-doping blue shifted the fundamental absorption edges in the UV region in the Sb-doped Sn_1 − xHf_xO₂ films. Additionally, the optical transmission at 310 nm, T₃₁₀, increased as the Hf concentration increased, whereas the electrical conductivity was inversely proportional to the Hf concentration. On the other hand, thinner films (150-nm thick) with x = 0.00 showed both a high electrical conductivity over 100 S cm^− 1 and a high transparency T₃₁₀ = 65% after high temperature annealing.     

Dielectric properties of sol-gel derived high-k titanium silicate thin films

High-k dielectric titanium silicate (Ti_xSi_1 − xO₂) thin films have been deposited by means of an optimized sol-gel process. At the optimal firing temperature of 600 °C, the Ti_0.5Si_0.5O₂ films are shown to exhibit not only a dielectric constant (k) as high as ∼ 23 but more importantly the lowest leakage current and dielectric losses. Fourier transform infrared spectroscopy shows an absorbance peak at 930 cm^− 1, which is a clear signature of the formation of Ti-O-Si bondings in all the silicate films. The developed sol-gel process offers the required latitude to grow Ti_xSi_1 − xO₂ with any composition (x) in the whole 0 ≤ x ≤ 1 range. Thus, the k value of the Ti_xSi_1 − xO₂ films can be tuned at any value between that of SiO₂ (3.8) to that of TiO₂ (k ∼ 60) by simply controlling the TiO₂ content of the films. The composition dependence of the dielectric constant of the Ti_xSi_1 − xO₂ films is analyzed in the light of existing models for dielectric composites.     

Spray deposition and property analysis of anatase phase titania (TiO2) nanostructures

Anatase phase titanium dioxide thin films have been deposited at various substrate temperatures by chemical spray pyrolysis of an aerosol of titanyl acetylacetonate. Deposited TiO₂ films were nanocrystalline and preferentially oriented along [101] direction, uniform and adherent to the glass substrate. Best films processed at 450 °C were characterized to analyze its phase composition, texture, roughness, optical and electrical properties. X-ray photoelectron spectroscopy revealed that the surface of the film has only the Ti⁴⁺ cations to form perfect TiO₂ stoichiometry with less amount of hydration. Atomic force microscopy image demonstrated the existence of homogeneous and rough surface, suitable for electrocatalytic applications. The film has an optical transmittance more than 90% and the refractive index of 2.07 was recorded at the wavelength 633 nm. Due to nano-sized grains, obtained optical band gap (3.65 eV) of the TiO₂ thin film was larger than that of the bulk TiO₂ (3.2 eV). Calculated porosity of the films 0.44, revealed the porous nature of the films. Hall measurements indicated that these materials are p-type and yield a carrier density of the order 8.8 × 10²⁰ cm⁻³ and a carrier mobility of 0.48 × 10⁻⁶ cm²/Vs. The dc electrical conductivity was therefore very low (8.91 × 10⁻⁶ S/cm) because of lower value of mean free path of the charge carriers (4.36 × 10⁻¹¹ cm). It gives an impression that the process of spray pyrolysis provides an easy way to tailor make thin films possessing superior properties.     

Novel transparent conducting oxide: Anatase Ti1−xNbxO2

Single-crystalline Ti_1−xNb_xO₂ (x = 0.2) films of 40 nm thickness were deposited on SrTiO₃ (100) substrates by the pulsed laser deposition (PLD) technique. X-ray diffraction measurement confirmed epitaxial growth of anatase (001) film. The resistivity of Ti_1−xNb_xO₂ films with x ≥ 0.03 is 2-3 × 10^− 4 Ω cm at room temperature. The carrier density of Ti_1−xNb_xO₂, which is almost proportional to the Nb concentration, can be controlled in a range of 1 × 10¹⁹ to 2 × 10²¹ cm^− 3. Optical measurements revealed that internal transmittance in the visible and near-infrared region for films with x = 0.03 was more than 97%. These results demonstrate that the presently developed anatase Ti_1−xNb_xO₂ is one of the promising candidates for the practical TCOs.     

Synthesis of non-stoichiometric Bi2O4−x by oxidative precipitation

Bi₂O_4−x, a Bi mixed-valence phase was prepared at 95 °C, by a precipitation process, in a basic medium with a highly oxidizing K₂S₂O₈/Na₂S₂O₈. This phase has a low thermal stability as it decomposes below 400 °C in a multiple step process by some O₂ losses prior to finally transforming into γ-Bi₂O₃. The as-prepared powders are 50-60 nm in size with a narrow size distribution. Optical spectra of Bi₂O_4−x exhibit a broad absorption band with a band gap of ∼1.4 eV as compared to 2.61 eV for Bi₂O₃. The composition of this non-stoichiometric phase, which crystallizes in cubic fluorite related structure with a cell parameter of 5.538(3) Å, is Bi₂O_{3.65 ± 0.10}.