Phosphate removal from solution using steel slag through magnetic separation

Steel slag with magnetic separation was used to remove phosphate from aqueous solutions. The influence of adsorbent dose, pH, and temperature on phosphate removal was investigated in a series of batch experiments. Phosphate removal increased with the increasing temperature, adsorbent dose and decreased with increasing initial phosphate concentrations, while it was at its peak at pH of 5.5. The phosphate removal predominantly occurred through ion exchange. The specific surface area of the steel slag was 2.09m2/g. The adsorption of phosphate followed both Langmuir and Freundlich isotherms. The maximum adsorption capacity of the steel slag was 5.3mgP/g. The removal rates of total phosphorus (TP) and dissolved phosphorus (DP) from secondary effluents were 62-79% and 71-82%, respectively. Due to their low cost and high capability, it was concluded that the steel slag may be an efficient adsorbent to remove phosphate both from solution and wastewater.     

Phosphate removal from wastewater using red mud

Red mud, a waste residue of alumina refinery, has been used to develop effective adsorbents to remove phosphate from aqueous solution. Acid and acid-thermal treatments were employed to treat the raw red mud. The effects of different treatment methods, pH of solution and operating temperature on adsorption have been examined in batch experiments. It was found that all activated red mud samples show higher surface area and total pore volume as well as higher adsorption capacity for phosphate removal. The red mud with HCl treatment shows the highest adsorption capacity among all the red mud samples, giving adsorption capacity of 0.58 mg P/g at pH 5.5 and 40 degrees C. The adsorption capacity of the red mud adsorbents decreases with increase of pH. At pH 2, the red mud with HCl treatment exhibits adsorption of 0.8 mg P/g while the adsorption can be lowered to 0.05 mg P/g at pH 10. However, the adsorption is improved at higher temperature by increasing 25% from 30 to 40 degrees C. The kinetic studies of phosphate adsorption onto red mud indicate that the adsorption mainly follows the parallel first-order kinetics due to the presence of two acidic phosphorus species, H(2)PO(4)(-) and HPO(4)(2-). An analysis of the adsorption data indicates that the Freundlich isotherm provides a better fitting than the Langmuir model.     

Removal of Pb(II) ions from aqueous solutions by sulphuric acid-treated wheat bran

Sulphuric acid-treated wheat bran (STWB) was used as an adsorbent to remove Pb(II) ions from aqueous solution. It was observed that the adsorption yield of Pb(II) ions was found to be pH dependent. The equilibrium time for the process was determined as 2h. STWB gave the highest adsorption yield at around pH 6.0. At this pH, adsorption percentage for an initial Pb(II) ions concentration of 100mg/L was found to be 82.8 at 25 degrees C for contact time of 2h. The equilibrium data obtained at different temperatures fitted to the non-linear form of Langmuir, Freundlich and Redlich-Peterson and linear form of Langmuir and Freundlich models. Isotherm constants were calculated and compared for the models used. The maximum adsorption capacity (q(max)) which was obtained linear form of Langmuir model increased from 55.56 to 79.37mg/g with increasing temperature from 25 to 60 degrees C. Similar trend was observed for other isotherm constants related to the adsorption capacity. Linear form of Langmuir isotherm data was evaluated to determine the thermodynamic parameters for the process. Thermodynamic parameters show that adsorption process of Pb(II) ions is an endothermic and more effective process at high temperatures. The pseudo nth order kinetic model was successfully applied to the kinetic data and the order (n) of adsorption reaction was calculated at the range from 1.711 to 1.929. The values of k(ad) were found to be 5.82x10(-4) and 21.81x10(-4)(min(-1))(mg/g)(1-n) at 25 and 60 degrees C, respectively. Activation energy was determined as 29.65kJ/mol for the process. This suggest that the adsorption Pb(II) ions by STWB is chemically controlled.     

Grass waste: A novel sorbent for the removal of basic dye from aqueous solution

The aim of the present work was to investigate the feasibility of grass waste (GW) for methylene blue (MB) adsorption. The adsorption of MB on GW material was studied as a function of GW dose (0.05–1.20 g), solution pH 3–10, contact time and initial concentration (70–380 mg/L). The influence of these parameters on the adsorption capacity was studied using the batch process. The experimental data were analyzed by the Langmuir and Freundlich isotherms. The adsorption isotherm was found to follow the Langmuir model. The monolayer adsorption capacity was found to be 457.640 mg/g. The kinetic data were fitted to the pseudo-first-order and pseudo-second-order models, and were found to follow closely the pseudo-second-order kinetic model. The results revealed that GW adsorbent is potentially low-cost adsorbent for adsorption of MB.     

Removal of copper from aqueous solution using Ulva fasciata sp.--a marine green algae

Batch adsorption experiments were carried out for the removal of copper from its aqueous solution using Ulva fasciata sp. a marine green algae as adsorbent. The adsorption of Cu(II) by Ulva fasciata sp. was investigated as a function of pH, contact time, initial Cu(II) and adsorbent concentrations and adsorbent size. About 0.1 g of Ulva fasciata sp. was found to be enough to remove 95% of 20 mg/L copper from 30 mL aqueous solution in 20 min. The optimum pH value was found to be 5. The dynamic data fitted to the pseudo-second order kinetic model. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms and the isotherm constants were determined. The experimental adsorption data were fitted to the Langmuir adsorption model. The maximum adsorption capacity was 26.88 mg/g. The applicability of Lagergren kinetic model was also investigated.     

Removal of Cu(II) ions by activated poplar sawdust (Samsun clone) from aqueous solutions

In this work, adsorption of Cu(II) ions on sawdust (SD) and activated sawdust (ASD) has been studied by using batch adsorption techniques. The equilibrium adsorption level was determined to be a function of the pH, initial Cu(II) concentration, and adsorbent dosage. The equilibrium nature of Cu(II) adsorption has been described by the Freundlich and Langmuir isotherms. The experimental adsorption data were fitted to the Langmuir adsorption model both sawdust and activated sawdust. The equilibrium capacity of sawdust and activated sawdust were 5.432 and 13.495 mg copper per g adsorbent, respectively at room temperature and natural pH. The maximum adsorption capacity was obtained at the maximum zeta potential value that -74.5 mV (pH 5) for activated sawdust and at -48.4 mV (pH 4) for sawdust. It was observed that activated sawdust was a suitable adsorbent than sawdust for removal of Cu(II) from aqueous solutions.     

活性炭负载Fe(Ⅲ)氧化物去除水中的磷酸根

利用活性炭负载铁氧化物制备了复合吸附剂,并用于水中磷酸根的去除.采用BET,SEM及XRD等手段对复合吸附剂的物理化学特性进行了表征,用静态吸附实验方法比较研究了复合吸附剂和活性炭从水溶液中吸附磷酸根的性质.结果表明:复合吸附剂具有快的吸附速度和高的吸附容量,其吸附磷酸根的性质受溶液pH值、铁含量及阴离子浓度的影响.在pH=3.0时,复合吸附剂对磷酸根的吸附容量为98.39 mg/g,而活性炭为78.90 mg/g.相比之下,Freundlich模型比Langmuir模型能更好地描述复合吸附剂和活性炭对磷酸根的吸附过程;而Lagergren二级方程却能很好地描述复合吸附剂对磷酸根的吸附动力学.水合氧化铁/活性炭复合吸附剂吸附磷酸根为吸热过程.     

Adsorption of copper ions from aqueous solution by citric acid modified soybean straw

The objectives of the present study were to convert soybean straw to a metal ion adsorbent and further to investigate the potential of using the adsorbent for the removal of Cu(2+) from aqueous solution. The soybean straw was water or base washed and citric acid (CA) modified to enhance its nature adsorption capacity. The morphological and chemical characteristics of the adsorbent were evaluated by spectroscopy and N(2)-adsorption techniques. The porous structure, as well as high amounts of introduced free carboxyl groups of CA modified soybean straw makes the adsorbent be good to retain Cu(2+). The adsorption capacities increased when the solution pH increased from 2 to 6 and reached the maximum value at pH 6 (0.64 mmol g(-1) for the base washed, CA modified soybean straw (CA-BWSS)). The Cu(2+) uptake increased and percentage adsorption of the Cu(2+) decreased with the increase in initial Cu(2+) concentration from 1 mM to 20 mM. Both the Langmuir and Freundlich adsorption isotherms were tested, and the Freundlich model fited much better than the Langmuir model. It was found that CA-BWSS have the highest adsorption capacity of the four kinds of pretreated soybean straw.     

Adsorption of copper ions onto microwave stabilized heavy metal sludge

Microwave stabilized heavy metal sludge was used as an adsorbent to remove the copper ions from aqueous solution. The adsorption characteristics of copper on the stabilized-sludge were studied by various models, such as Freundlich and Langmuir isotherm equation. Results show that the pH(zpc) of stabilized-sludge was at 9.2-9.5. Moreover, the adsorption of copper ions onto the stabilized-sludge surface was mainly on account of the heterogeneous surface of the stabilized-sludge. In the dynamic study, the experimental data was fitted to the intraparticle diffusion model, pseudo-first order model and pseudo-second order model. However, the experimental data was only well correlated with pseudo-second order model with the correlation coefficient>0.995. Furthermore, both Freundlich and Langmuir isotherm equations were found to represent the measured adsorption data well. From the Langmuir equation, the adsorption capacity increased from 18 to 28 mg/g as the temperature rose from 15 to 55 degrees C, since this adsorption process was an endothermic reaction. After this adsorption process, copper ions can be concentrated on and in a small bead and recovery efficiently.     

Environmental risk index: a tool to assess the safety of dams for leachate

Bagasse-based ion adsorbent was prepared by chemically modifying bagasse with acrylonitrile and hydroxylamine with the aim to enhance the ability of removal heavy metal ions from wastewater. The purified modified materials were characterized by Fourier transform infrared (FT-IR). Batch experiments of Cu(II) ions (Cu(2+)) adsorption on the bagasse adsorbent were performed. Effects of the adsorbent dosage, initial pH of the solution, temperature of the Cu(2+) solution, and initial Cu(2+) concentration on the adsorption of Cu(2+) were studied, respectively. Langmuir and Freundlich models were applied to describe the adsorption isotherm of Cu(2+) by bagasse adsorbent. The results indicated that Langmuir model fitted the adsorption equilibrium data better than the Freundlich isotherm model. Two kinetic models, including pseudo-first-order and pseudo-second-order, were also used to analyze the Cu(2+) adsorption process, and the results showed that the pseudo-second-order with correlation coefficients greater than 0.999 was more suitable than pseudo-first-order.     

Sorption of copper(II) ion from aqueous solution by Tectona grandis l.f. (teak leaves powder)

Studies on a batch sorption system using Tectona grandis l.f. as adsorbent was investigated to remove copper(II) from aqueous solutions. The adsorption experiments were performed under various conditions such as different initial concentrations, pH, adsorbent dosage and adsorbent particle size. The data showed that 0.1 g of Tectona grandis l.f. was found to remove 71.66% of 20 mg/L copper(II) from 30 mL aqueous solution in 180 min. The experimental equilibrium data were adjusted by the adsorption isotherms from Langmuir and Freundlich models and their equilibrium parameters were determined. The best-adjusted model to the experimental equilibrium data for Tectona grandis l.f. was the Langmuir model. Using the Langmuir model equation, the monolayer sorption capacity of Tectona grandis l.f. was evaluated and found to be 95.40 mg/g. The optimum pH value was found to be 5.5. The pseudo-first-order and pseudo-second-order kinetic models were used to describe the kinetic data. The dynamic data fitted the pseudo-second-order kinetic model.     

Removal of lead from aqueous solution using Syzygium cumini L.: equilibrium and kinetic studies

The biosorption of lead ions from aqueous solution by Syzygium cumini L. was studied in a batch adsorption system as a function of pH, contact time, lead ion concentration, adsorbent concentration and adsorbent size. The biosorption capacities and rates of lead ions onto S. cumini L. were evaluated. The Langmuir, Freundlich, Redlich-Peterson and Temkin adsorption models were applied to describe the isotherms and isotherm constants. Biosorption isothermal data could be well interpreted by the Langmuir model followed by Temkin model with maximum adsorption capacity of 32.47 mg/g of lead ion on S. cumini L. leaves biomass. The kinetic experimental data were properly correlated with the second-order kinetic model.     

A novel agricultural waste adsorbent for the removal of cationic dye from aqueous solutions

In this paper, pineapple stem (PS) waste, an agricultural waste available in large quantity in Malaysia, was utilized as low-cost adsorbent to remove basic dye (methylene blue, MB) from aqueous solution by adsorption. Batch mode experiments were conducted at 30 degrees C to study the effects of initial concentration of methylene blue, contact time and pH on dye adsorption. Equilibrium adsorption isotherms and kinetic were investigated. The experimental data were analyzed by the Langmuir and Freundlich models and the isotherm data fitted well to the Langmuir isotherm with monolayer adsorption capacity of 119.05mg/g. The kinetic data obtained at different concentrations were analyzed using a pseudo-first-order and pseudo-second-order equation and intraparticle diffusion equation. The experimental data fitted very well the pseudo-second-order kinetic model. The PS was found to be very effective adsorbent for MB adsorption.     

Removal of phosphate from polluted water by lanthanum doped vesuvianite

The adsorption capacities of vesuvianite and lanthanum doped vesuvianite were studied. The effects of different mass ratios of La/vesuvianite at different contact times, pHs, and temperatures on adsorption capacity were also studied. It was found that lanthanum doped vesuvianite exhibited higher adsorption capacity than undoped one due to the reaction of bounded lanthanum with phosphate. The adsorption capacity of lanthanum doped vesuvianite for phosphate removal increased with the increase of La/vesuvianite mass ratio. The Freundlich and Langmuir models were used to simulate the sorption equilibrium, and the results indicate that the Langmuir model had a better correlation with the experimental data than the Freundlich model did. When the initial phosphate concentration was 1 mg P/L, the adsorptive capacity rate would be 1.32 mg P/g lanthanum doped vesuvianite (La/vesuvianite mass ratio ≥0.14) at pH between 6 and 9 after 40 h. The concentrations of residual lanthanum ions in solution at different conditions were measured. Lanthanum doped vesuvianite was also used for the removal of phosphate in a polluted river water and it could be easily recycled once without losing its activity to a greater extent.     

Removal of arsenite from water by synthetic siderite: behaviors and mechanisms

Synthetic siderite has been used as adsorbent for As(III) removal in this study. Effects of contact time, temperature, pH, co-existing anions on As(III) adsorption were intensively investigated. Adsorption mechanisms were also studied using the X-ray absorption technique. Results show that the maximum adsorption capacity is up to 9.98 mg g(-1) at 25°C at a siderite dosage of 2 g L(-1). Adsorption kinetics agrees with the Lagergren pseudo-second order model. Arsenic(III) adsorption can be better described by Langmuir isotherm model for As(III) adsorption at 55°C, indicating that the coverage of the adsorption sites is in the form of monolayer, although Freundlich isotherm yields a better fit to the experimental data at 25, 35 and 45°C. Thermodynamic study indicates that As(III) adsorption on the synthetic siderite is spontaneous and endothermic in nature. The adsorption capacity is enhanced with the increase in reaction temperature. The adsorption is independent on solution pH between 3.0 and 9.6. The presence of NO(3)(-), SO(4)(2-), PO(4)(3-) or SiO(3)(2-) with element concentrations less than 20 mg L(-1) does not have adverse effect on As(III) adsorption. XANES spectra indicate that As mainly occurs as As(V) in the As adsorbed-materials, and the fraction of oxidized As(III) increases with the decrease in As(III) concentration. The formation of Fe hydroxide minerals (such as lepidocrocite and goethite) followed by As(III) oxidation and adsorption is shown to be the main mechanism of As(III) removal by the synthetic siderite.     

Adsorption of Direct Red 80 dye from aqueous solution onto almond shells: effect of pH, initial concentration and shell type

The adsorption of Direct Red 80 (DR 80) dye from aqueous solution on almond shells as an eco-friendly and low-cost adsorbent was studied. The effect of shell type (internal, external and mixture shells), pH and initial dye concentration were considered to evaluate the sorption capacity of almond shell adsorbent. The mixture type of almond shell showed to be more effective. The adsorption studies revealed that the mixture type of almond shells remove about 97% of the DR 80 dye from aqueous phase after 1h of the adsorption process in a batch system. Although, pH changes did not appreciably affect the adsorption process but the maximum adsorption capacity of different types of almond shells (20.5, 16.96 and 16.4 mg/g for mixture, external and internal shells) were obtained at pH 2. However, in order to have a better control on the experimental conditions, pH 6 was selected for conducting all adsorption experiments. Initial dye concentration was varied from 50 to 150 mg/L. Higher concentrations of dye in aqueous solution reduced DR 80 dye adsorption efficiency of almond shells. Equilibrium data were attempted by various adsorption isotherms including Langmuir, Freundlich and Brunauer-Emmett-Teller (BET) models. It was found that the adsorption process by mixture type of almond shells follows the Langmuir non-linear isotherm. Furthermore, the experimental data by internal and external almond shells could be well described by the BET and Freundlich isotherm models, respectively. The pseudo-second-order kinetics provides the best correlation of the experimental data.     

Equilibrium and kinetic studies for the biosorption system of copper(II) ion from aqueous solution using Tectona grandis L.f. leaves powder

The biosorption of copper(II) ions from aqueous solution by Tectona grandis L.f. was studied in a batch adsorption system as a function of pH, metal ion concentration, adsorbent concentration and adsorbent size. The biosorption capacities and rates of copper(II) ions onto T. grandis L.f. were evaluated. The Langmuir, Freundlich, Redlich-Peterson and Temkin adsorption models were applied to describe the isotherms and isotherm constants. Biosorption isothermal data could be well interpreted by the Langmuir model with maximum adsorption capacity of 15.43 mg/g of copper(II) ion on T. grandis L.f. leaves powder. The kinetic experimental data properly correlated with the second-order kinetic model. Various thermodynamic parameters such as deltaG(o), deltaH(o), and deltaS(o) were calculated indicating that this system was a spontaneous and exothermic process.     

Factors influencing the removal of fluoride from aqueous solution by calcined Mg-Al-CO3 layered double hydroxides

Layered double hydroxides (LDH) calcined at different temperatures (denoted as CLDH) have been demonstrated to recover their original layered structure in the presence of appropriate anions. In the light of this so-called "memory effect", a study of removal of fluoride from aqueous solution by calcined Mg-Al-CO(3)-LDH has been carried out. The LDH calcined at 500 degrees C had the highest capacity of removal of fluoride ion, because of retention of its intrinsic structure. The CLDH with an Mg/Al ratio of 2 has a remarkable ability to adsorb anions. The adsorption loading is higher for the calcined Mg-Al-LDH than for calcined Zn-Al and Ni-Al-LDH. The influence of varying the conditions for removal of fluoride, such as the pH of aqueous solution, the initial fluoride concentration, the dosage of adsorbent, and temperature on removal of fluoride have been investigated. The influence of co-existing anions in fluoride aqueous solution indicates that the percentage of removal of fluoride increased in order PO(4)(3-) < Cl(-) approximately SO(4)(2-) < Br(-) < NO(3)(-). It was found that maximum removal of fluoride from aqueous solutions was obtained in 6h at pH 6.0 with an initial concentration of 50 mg/L, and that the retention of fluoride ions by the CLDH material was 98% or higher. The residual fluoride concentration was found to be 0.4 mg/L with an initial concentration of 20 mg/L, which meets the national standard for drinking water quality. The Freundlich isotherm and Langmuir isotherm were used to fit the data of equilibrium experiments. The results of X-ray diffraction, FT-IR and TG-MS demonstrate that the adsorption phenomenon is accompanied by rehydration with concomitant uptake of fluoride ions to rebuild the initial layered structure.     

Removal of toxic zinc from water/wastewater using eucalyptus seeds activated carbon: non‐linear regression analysis

In the present study, a novel activated carbon was prepared from low‐cost eucalyptus seeds, which was utilised for the effectively removal of toxic zinc from the water/wastewater. The prepared adsorbent was studied by Fourier transform infrared spectroscopy and scanning electron microscopic characterisation studies. Adsorption process was experimentally performed for optimising the influencing factors such as adsorbent dosage, solution pH, contact time, initial zinc concentration, and temperature for the maximum removal of zinc from aqueous solution. Adsorption isotherm of zinc removal was ensued Freundlich model, and the kinetic model ensued pseudo‐second order model. Langmuir monolayer adsorption capacity of the adsorbent for zinc removal was evaluated as 80.37 mg/g. The results of the thermodynamic studies suggested that the adsorption process was exothermic, thermodynamically feasible and impulsive process. Finally, a batch adsorber was planned to remove zinc from known volume and known concentration of wastewater using best obeyed model such as Freundlich. The experimental details showed the newly prepared material can be effectively utilised as a cheap material for the adsorption of toxic metal ions from the contaminated water.Inspec keywords: wastewater treatment, activated carbon, zinc, toxicology, regression analysis, Fourier transform infrared spectra, scanning electron microscopy, adsorption, pH, reaction kinetics, monolayers, thermodynamics, contaminationOther keywords: Zn, toxic metal ion adsorption, contaminated water, batch adsorber, exothermic process, thermodynamic process, Langmuir monolayer adsorption capacity, pseudosecond‐order model, kinetic model, Freundlich model, adsorption isotherm, aqueous solution, temperature value, initial zinc concentration, contact time, pH value, adsorbent dosage, scanning electron microscopic characterisation, Fourier transform infrared spectroscopy, nonlinear regression analysis, eucalyptus seed activated carbon, wastewater, toxic zinc removal