CO2 Hydrogenation to Methanol Over Cu/ZnO/Al2O3 Catalysts Prepared by a Novel Gel-Network-Coprecipitation Method

A novel gel-network-coprecipitation process has been developed to prepare ultrafine Cu/ZnO/Al₂O₃ catalysts for methanol synthesis from CO₂ hydrogenation. It is demonstrated that the gel-network-coprecipitation method can allow the preparation of the ultrafine Cu/ZnO/Al₂O₃ catalysts by homogeneous coprecipitation of the metal nitrate salts in the gel network formed by gelatin solution, which makes the metallic copper in the reduced catalyst exist in much smaller crystallite size and exhibit a much higher metallic copper-specific surface area. The effect of the gel concentration of gelatin on the structure, morphology and catalytic properties of the Cu/ZnO/Al₂O₃ catalysts for methanol synthesis from hydrogenation of carbon dioxide was investigated. The Cu/ZnO/Al₂O₃ catalysts prepared by the gel-network-coprecipitation method exhibit a high catalytic activity and selectivity in CO₂ hydrogenation to methanol.     

Effects of catalyst composition on methanol synthesis from CO2/H2

Effects of catalyst composition have been studied for Cu/support and Cu/ZnO/supports in methanol synthesis from CO₂/H₂. A strong effect of support has been observed. Different supports brought about different behavior in temperature-programmed reduction of copper, different copper surface areas, and different catalytic activity and selectivity. It seemed possible to find catalyst supports that might perform better than commercial Cu/ZnO/Al₂O₃ catalysts. A correlation was observed between catalytic activity and the copper surface area which was varied by using different supports. However, the sup]>orts appeared to influence other catalytic properties as well, for example, the surface oxygen coverage.     

Role of ZnO in Cu/ZnO/Al2O3 catalyst for hydrogenolysis of butyl butyrate

For hydrogenolysis of butyl butyrate (BB), a series of Cu/ZnO/Al₂O₃ catalysts with different metal compositions were prepared, and characterized by N₂O chemisorption for measuring Cu surface area and by chromatographic experiment for determining the heat of BB adsorption. As a result, the presence of ZnO in Cu-based catalysts was found to enhance the catalytic activity of Cu due to dual function of ZnO. The Cu surface area was linearly correlated with the butanol productivity, demonstrating that ZnO exerts the structural function in Cu/ZnO/Al₂O₃ catalysts. Additionally, the role of ZnO as a chemical contributor was revealed such that its presence leads to lower activation energy of the surface reaction, thus resulting in higher Cu catalytic activity obtained at a low temperature such as 200 °C. Consequently, optimizing the Cu/Zn ratio in Cu/ZnO/Al₂O₃ catalyst is required to tune its structural and chemical characteristics of Cu metals, and thus to obtain a higher activity on the hydrogenolysis reaction.     

Influence of preparation method on performance of Cu(Zn)(Zr)-alumina catalysts for the hydrogen production via steam reforming of methanol

The selective production of hydrogen via steam reforming of methanol (SRM) was performed using prepared catalysts at atmospheric pressure over a temperature range 200–260^∘C. Reverse water gas shift reaction and methanol decomposition reactions also take place simultaneously with the steam reforming reaction producing carbon monoxide which is highly poisonous to the platinum anode of PEM fuel cell, therefore the detailed study of effect of catalyst preparation method and of different promoters on SRM has been carried out for the minimization of carbon monoxide formation and maximization of hydrogen production. Wet impregnation and co-precipitation methods have been comparatively examined for the preparation of precursors to Cu(Zn)(Al₂O₃) and Cu(Zn)(Zr)(Al₂O₃). The catalyst preparation method affected the methanol conversion, hydrogen yield and carbon monoxide formation significantly. Incorporation of zirconia in Cu(Zn)(Al₂O₃) catalyst enhanced the catalytic activity, hydrogen selectivity and also lower the CO formation. Catalyst Cu(Zn)(Zr)(Al₂O₃) with composition Cu/Zn/Zr/Al:12/4/4/80 prepared by co-precipitation method was the most active catalyst giving methanol conversion up to 97% and CO concentration up to 400 ppm. Catalysts were characterized by atomic absorption spectroscopy (AAS), Brunauer-Emett-Teller (BET) surface area, pore volume, pore size and X-ray powder diffraction (XRPD). The XRPD patterns revealed that the addition of zirconia improves the dispersion of copper which resulted in the better catalytic performance of Cu(Zn)(Zr)(Al₂O₃). The time-on-stream (TOS) catalysts stability test was also conducted for which the Cu(Zn)(Zr)(Al₂O₃) catalyst gave the consistent performance for a long time compared to other catalysts.     

Effects of Pretreatments of Cu/ZnO-Based Catalysts on Their Activities for the Water–Gas Shift Reaction

The effects of the pretreatments of Cu/ZnO-based catalysts prepared by a coprecipitation method on their activities for the water–gas shift reaction at 523K were investigated. The activity of a Cu/ZnO/ZrO₂/Al₂O₃ catalyst for the water–gas shift reaction was less affected by calcination at temperatures ranging from 673-973K and by H₂ treatment at 573 or 723K than that of a Cu/ZnO/Al₂O₃ catalyst. The catalyst activity could be correlated mainly to the Cu surface area of the catalyst.     

Steam reforming of methanol using Cu-ZnO catalysts supported on nanoparticle alumina

Methanol steam reforming was studied over several catalysts made by deposition of copper and zinc precursors onto nanoparticle alumina. The results were compared to those of a commercially available copper, zinc oxide and alumina catalyst. Temperature programmed reduction, BET surface area measurements, and N₂O decomposition were used to characterize the catalyst surfaces. XRD was used to study the bulk structure of the catalysts, and XPS was used to determine the chemical states of the surface species. The nanoparticle-supported catalysts achieved similar conversions as the commercial reference catalyst but at slightly higher temperatures. However, the nanoparticle-supported catalysts also exhibited a significantly lower CO selectivity at a given temperature and space time than the reference catalyst. Furthermore, the turnover frequencies of the nanoparticle-supported catalysts were higher than that of the commercial catalyst, which means that the activity of the surface copper is higher. It was determined that high alumina concentrations ultimately decrease catalytic activity as well as promote undesirable CH₂O formation. The lower catalytic activity may be due to strong Cu-Al₂O₃ interactions, which result in Cu species which are not easily reduced. Furthermore, the acidity of the alumina support appears to promote CH₂O formation, which at low Cu concentrations is not reformed to CO₂ and H₂. The CO levels present in this study are above what can be explained by the reverse water-gas-shift (WGS) reaction. While coking is not a significant deactivation pathway, migration of ZnO to the surface of the catalyst (or of Cu to the bulk of the catalyst) does explain the permanent loss of catalytic activity. Cu₂O is present on the spent nanoparticle catalysts and it is likely that the Cu⁺/Cu⁰ ratio is of importance both for the catalytic activity and the CO selectivity.     

Deactivation of Supported Copper Catalysts for Methanol Synthesis

Binary Cu/ZnO and Cu/Al₂O₃ as well as ternary Cu/ZnO/Al₂O₃ catalysts were investigated with respect to their catalytic activity and stability in methanol synthesis. In a rapid aging test, activity measurements were carried out in combination with the determination of the specific Cu surface area. A close correlation between the loss of catalytic activity and the decrease in specific Cu surface area was found due to sintering of the Cu particles. Differences in the deactivation behavior and the area-activity relationship of each catalyst system imply that the catalysts should be grouped in different classes.     

Nanodispersed Au/Al2O3 catalysts for low-temperature CO oxidation: Results of research activity at the Boreskov Institute of Catalysis

This paper presents some important results of the studies on preparation and catalytic properties of nanodispersed Au/Al₂O₃ catalysts for low-temperature CO oxidation, which are carried out at the Boreskov Institute of Catalysis (BIC) starting from 2001. The catalysts with a gold loading of 1–2 wt.% were prepared via deposition of Au complexes onto different aluminas by means of various techniques (“deposition-precipitation” (DP), incipient wetness, “chemical liquid-phase grafting” (CLPG), chemical vapor deposition (CVD)). These catalysts have been characterized comparatively by a number of physical methods (XRD, TEM, diffuse reflectance UV/vis and XPS) and catalytically tested for combustion of CO impurity (1%) in wet air stream at near-ambient temperature. Using the hydroxide or chloride gold complexes capable of chemical interaction with the surface groups of alumina as the catalyst precursors (DP and incipient wetness techniques, respectively) produces the catalysts that contain metallic Au particles mainly of 2–4 nm in diameter, uniformly distributed between the external and internal surfaces of the support granules together with the surface “ionic” Au oxide species. Application of organogold precursors gives the supported Au catalysts of egg shell type which are either close by mean Au particle size to what we obtain by DP and incipient wetness techniques (CVD of (CH₃)₂Au(acac) vapor on highly dehydrated Al₂O₃ in a rotating reactor under static conditions) or contain Au crystallites of no less than 7 nm in size (CLPG method). Regardless of deposition technique, only the Cl-free Au/Al₂O₃ catalysts containing the small Au particles (d_i ≤ 5 nm) reveal the high catalytic activity toward CO oxidation under near-ambient conditions, the catalyst stability being provided by adding the water vapor into the reaction feed. The results of testing of the nanodispersed Au/Al₂O₃ catalysts under conditions which simulate in part removal of CO from ambient air or diesel exhaust are discussed in comparison with the data obtained for the commercial Pd and Pt catalysts under the same conditions.     

A new method of low-temperature methanol synthesis on Cu/ZnO/Al2O3 catalysts from CO/CO2/H2

A new synthesis method of low-temperature methanol proceeded on Cu/ZnO/Al₂O₃ catalysts from CO/CO₂/H₂ using 2-butanol as promoters. The Cu/ZnO/Al₂O₃ catalysts were prepared by co-impregnation of r-Al₂O₃ with an aqueous solution of copper nitrate and zinc nitrate. The total carbon turnover frequency (TOF), the yield and selectivity of methanol were the highest by using the Cu/ZnO/Al₂O₃ catalyst with copper loading of 5% and the Zn/Cu molar ratio of 1/1, which precursor were not calcined, and reduced at 493 K. The activity of the catalysts increased due to the presence of the CuO/ZnO phase in the oxidized form of impregnation Cu/ZnO/Al₂O₃ catalysts. The active sites of the Cu/ZnO/Al₂O₃ catalyst for methanol synthesis are not only metallic Cu but also special sites such as the Cu–Zn site, i.e. metallic Cu and the Cu–Zn site work cooperatively to catalyze the methanol synthesis reaction.     

Gas phase hydrogenation of maleic anhydride to tetrahydrofuran by Cu/ZnO/TiO2 catalysts in the presence of n-butanol

Cu/ZnO/TiO₂ catalysts were prepared via the coprecipitation method. The catalysts were characterized by X-ray diffraction, X-ray photoelectron spectrometry, temperature programmed reduction, and N₂ adsorption. The catalytic activity of Cu/ZnO/TiO₂ catalyst in gas phase hydrogenation of maleic anhydride in the presence of n-butanol was studied at 235–280 °C and 1 MPa. The conversion of maleic anhydride was more than 95.7% and the selectivity of tetrahydrofuran was up to 92.7%. At the same time, n-butanol was converted to butyraldehyde and butyl butyrate via reactions, namely, dehydrogenation, disproportionation, and esterification. There were two kinds of CuO species present in the calcined Cu/ZnO/TiO₂ catalysts. At a lower copper content, the CuO species strongly interacted with ZnO and TiO₂; at a higher copper content, both the surface-anchored and bulk CuO species were present. The metallic copper (CuO) produced by the reduction of the surface-anchored CuO species favored the deep hydrogenation of maleic anhydride to tetrahydrofuran. The deep hydrogenation activity of Cu/ZnO/TiO₂ catalyst increased with the decrease of crystallite sizes of CuO and the increase of microstrain values. Compensations of reaction heat and H₂ in the coupling reaction of maleic anhydride hydrogenation and n-butanol dehydrogenation were distinct.     

A crucial role of O2 and O2 on mayenite structure for biomass tar steam reforming over Ni/Ca12Al14O33

Newly synthesized nickel calcium aluminum catalysts (Ni/Ca₁₂Al₁₄O₃₃) were tested in a fixed bed reactor for biomass tar steam reforming, toluene as tar destruction model compound. Four catalysts (Ni/Ca₁₂Al₁₄O₃₃) were prepared with Ni loading amount from 1, 3, 5 to 7 wt%, even 1% loading catalyst also showed excellent performance. Catalysts aged experiments in the absence (60 h on stream) and presence of H₂S were characterized by BET, X-ray diffraction (XRD), and Raman spectra. It was observed that Ni/Ca₁₂Al₁₄O₃₃ showed excellent sustainability against coke formation due to the “free oxygen” in the catalysts. It also exhibited higher H₂S-poisoning resistance property compared to the commercial catalysts Ni/Al₂O₃ (5%) and Ni/CaO_0.5/MgO_0.5. Raman spectra revealed that “free oxygen O₂⁻ and O₂²⁻” in the structure of the catalysts could be substituted by sulfur then protected Ni poisoning on some degree, but reactivation experiments by O₂ flowing showed that the sulfide Ni/Ca₁₂Al₁₄O₃₃ was difficult to completely restore, incorporation of sulfur in the structure only partly regain by O₂. The kinetic model proposes, as generally accepted, a first-order reaction for toluene with activation energy of 82.06 kJ mol⁻¹ was coincident with the literature data. The Ni/Ca₁₂Al₁₄O₃₃ catalyst was effective and relative cheap, which may be lead to reduction in the cost of hot gas cleaning process.     

Methanol synthesis pathway over Cu/ZrO2 catalysts: a time‐resolved DRIFT 13C‐labelling experiment

X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) have been used to characterize a series of Cu/Ce/Al₂O₃ catalysts. Catalysts were prepared by incipient wetness impregnation using metal nitrate and alkoxide precursors. Catalyst loadings were held constant at 12 wt% CuO and 5.1 wt% CeO₂. Mixed oxide catalysts were prepared by impregnation of cerium first, followed by copper. The information obtained from surface and bulk characterization has been correlated with CO and CH₄ oxidation activity of the catalysts. Cu/Al₂O₃ catalysts prepared using Cu(II) nitrate (CuN) and Cu(II) ethoxide (CuA) precursors consist of a mixture of copper surface phase and crystalline CuO. The CuA catalyst shows higher dispersion, less crystalline CuO phase, and lower oxidation activity for CO and CH₄ than the CuN catalyst. For Cu/Ce/Al₂O₃ catalysts, Ce has little effect on the dispersion and crystallinity of the copper species. However, Cu impregnation decreases the Ce dispersion and increases the amount of crystalline CeO₂ present in the catalysts, particularly in Ce modified alumina prepared using cerium alkoxide precursor (CeA). Cerium addition dramatically increases the CO oxidation activity, however, it has little effect on CH₄ oxidation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Investigating the effect of metal oxide additives on the properties of Cu/ZnO/Al2O3 catalysts in methanol synthesis from syngas using factorial experimental design

The Cu/ZnO/Al₂O₃ catalysts, prepared by co-precipitation method, have been modified by adding small amount of Mn, Mg, Zr, Cr, Ba, W and Ce oxides using design of experiments (1/16 full factorial design). The structure and morphology of catalysts were studied by X-ray diffraction (XRD) and BET. Performance of the prepared catalysts for CO/CO₂ hydrogenation to methanol was evaluated by using a stainless steel fixed-bed reactor at 5 MPa and 513 K. The oxide additives were found to influence the catalytic activity, dispersion of Cu, Cu crystallite size, surface composition of catalyst and stability of catalysts during their operations. The results showed that the Mn and Zr promoted catalysts have high performance for methanol synthesis from syngas.     

Activity and stability of Cu/ZnO/Al2O3 catalyst promoted with B2O3 for methanol synthesis

The addition of B₂O₃ to a Cu/ZnO/Al₂O₃ catalyst increased the activity of the catalyst for methanol synthesis after an induction period during the reaction. The stability of the B₂O₃-containing Cu/ZnO/Al₂O₃ catalyst was greatly improved by the addition of a small amount of colloidal silica to the catalyst. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis of DME from syngas on the bifunctional Cu–ZnO–Al2O3/Zr-modified ferrierite: Effect of Zr content

The catalytic activity on the coprecipitated Cu–ZnO–Al₂O₃/Zr-ferrierite (CZA–ZrFER) with different Zr content from 0 to 5 wt.% was investigated for the direct synthesis of dimethylether (DME) from H₂-deficient and biomass-derived model syngas (H₂/CO molar ratio = 0.93). The catalytic functionalities, such as CO conversion and DME selectivity, showed their maxima on the bifunctional catalyst with 3 wt.% Zr-modified ferrierite. Detailed characterization studies were conducted on the catalysts to measure their properties such as surface area, acidity by temperature-programmed desorption of ammonia (NH₃-TPD), reducibility of Cu oxide by temperature-programmed reduction (TPR), copper surface area measurements by N₂O titration method, electronic states of copper by IR analysis and particle size measurement by XRD and TEM analysis. The number of acid sites measured by NH₃-TPD on the bifunctional catalysts decreased monotonously with the increase of Zr content, meanwhile, the acidic strength is found to be minimal on the catalyst showing best performance. The reducibility of copper oxide and the surface area of metallic copper also exhibited their maximum values at the same Zr composition indicating that these are responsible for the optimum functionality of the bifunctional CZA–ZrFER catalyst. The role of easily reducible copper species with small particle size and the suppressed strong acidic sites is also emphasized in the consecutive reaction from syngas to DME on the bifunctional catalyst. The different behavior of intrinsic rate of the bifunctional catalysts is also well correlated with the metallic surface area of copper and the amount of acidic sites with their acidic strength.     

C9-aldehyde hydrogenation over nickel/kieselguhr catalysts in trickle bed reactor

The objective of the present study was to select the optimal catalyst and operating conditions for the manufacture of C₉-alcohol, using C₉-aldehyde and hydrogen, in a trickle bed reactor. When CaO, Ce₂O₃ or MgO was added as a promoter to the Ni/kieselguhr catalyst, the BET and Ni surface areas were increased. In the reaction for the manufacture of C₉-alcohol, using C₉-aldehyde and hydrogen in a batch reactor, a Ni–MgO/kieselguhr catalyst showed the highest activity. In addition, the catalyst using Na₂CO₃ as a precipitant showed the highest activity. According to the result of an experiment to find the optimal reaction conditions for C₉-alcohol synthesis, using C₉-aldehyde and hydrogen in a trickle bed reactor loaded with Ni–MgO/kieselguhr catalyst, the highest yield of C₉-alcohol was 91.5 wt% at 130 °C, 400 psi and WHSV = 3. The C₉-aldehyde hydrogenation performance of the Ni–MgO/kieselguhr catalyst was similar to that of a Cu/ZnO/Al₂O₃ catalyst, but superior to that of Cu–Ni–Cr–Na/Al₂O₃ and Ni–Mo/Al₂O₃ catalysts. In a long-term catalysis test, the Ni–MgO/kieselguhr catalyst showed higher stability than the Cu/ZnO/Al₂O₃ catalyst.     

Stable carbon dioxide reforming of methane over modified Ni/Al2O3 catalysts

CO₂ reforming of methane was studied over modified Ni/Al₂O₃ catalysts. The metal modifiers were Co, Cu, Zr, Mn, Mo, Ti, Ag and Sn. Relative to unmodified Ni/Al₂O₃, catalysts modified with Co, Cu and Zr showed slightly improved activity, while other promoters reduced the activity of CO₂ reforming. Mn-promoted catalyst showed a remarkable reduction in coke deposition, while entailing only a small reduction in catalytic activity compared to unmodified catalyst. The catalysts prepared at high calcination temperatures showed higher activity than those prepared at low calcination temperature. The Mn-promoted catalyst showed very low coke deposition even in the absence of diluent gas and the activity changed only slightly during 100 h operation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Dehydrogenation of cyclohexanol on Cu–ZnO/SiO2 catalysts: The role of copper species

For the dehydrogenation of cyclohexanol a series of Cu–ZnO/SiO₂ catalysts with various Cu to ZnO molar ratios was prepared using the impregnation method, with the loading of copper fixed at 9.5 at.%. The catalysts were characterized by XPS, H₂–N₂O titration, BET, H₂-TPR, NH₃-TPD and XRD techniques. The results indicate that the addition of ZnO can improve the dispersion of copper species on reduced Cu–ZnO/SiO₂ (CZS) catalysts. Cu⁰ and Cu⁺ species were found on the reduced CZS catalysts surface, and the amount of Cu⁺ increased with the content of ZnO increasing. The addition of ZnO increased the acidity of the CZS catalysts. However, only Cu⁰ species can be found on the reduced Cu/SiO₂ (CS) catalyst surface. According to the reaction results, we found that the selectivity to phenol was related to the amount of Cu⁺ species, the Cu⁺ species should be the active sites for the production of phenol, the Cu⁰ is responsible for cyclohexanol dehydrogenation to cyclohexanone.     

CO removal from reformed fuel over Cu/ZnO/Al2O3 catalysts prepared by impregnation and coprecipitation methods

A composition of Cu/ZnO/Al₂O₃ catalysts prepared by the impregnation method was optimized for water gas shift reaction (WGSR) coupled with CO oxidation in the reformed gas. The optimum composition of the impregnated catalyst for high WGSR activity was 5 wt.% Cu/5 wt.% ZnO/Al₂O₃. The optimum loading amounts of Cu and ZnO in the impregnated catalyst were smaller than those in the coprecipitated catalyst. Its catalytic activity above 200 °C was comparable to that of the conventional coprecipitated Cu/ZnO/Al₂O₃ catalyst. However, the activity of the impregnated Cu/ZnO/Al₂O₃ catalysts was significantly lowered at 150 °C, whereas no deactivation was observed for the coprecipitated catalyst at the same temperature. It was found that deactivation occurred over impregnated catalysts with H₂O and/or O₂ in the reaction gas; it prevented CO adsorption on the surface.     

CO2 hydrogenation to methanol over Cu/ZnO/ZrO2 catalysts prepared via a route of solid-state reaction

Cu/ZnO/ZrO₂ catalysts were prepared by a route of solid-state reaction and tested for the synthesis of methanol from CO₂ hydrogenation. The effects of calcination temperature on the physicochemical properties of as-prepared catalysts were investigated by N₂ adsorption, XRD, TEM, N₂O titration and H₂-TPR techniques. The results show that the dispersion of copper species decreases with the increase in calcination temperature. Meanwhile, the phase transformation of zirconia from tetragonal to monoclinic was observed. The highest activity was achieved over the catalyst calcined at 400 °C. This method is a promising alternative for the preparation of highly efficient Cu/ZnO/ZrO₂ catalysts.