Microcellular Al2O3 Ceramics from Wood for Filter Applications

Microcellular biomorphous Al₂O₃ was produced by Al-vapor infiltration in pyrolyzed rattan and pine wood-derived biocarbon preforms. At 1600°C the biocarbon preforms reacted with gaseous aluminum to form Al₄C₃. After oxidation in air at temperatures between 1550° and 1650°C, for 3 h, the biocarbon preforms were fully converted into α-Al₂O₃. Owing to the high anisotropy of biomorphous Al₂O₃, the compressive strength behavior was strongly dependent on the loading direction. The compressive strength of the specimens (0.1–11 MPa) is strongly dependent on their overall porosity and their behavior could be explained using the Gibson–Ashby model. The Darcian permeability ( k ₁), as well as the non-Darcian permeability ( k ₂), increased with an increase of the total porosity. The Darcian permeability of biomorphous Al₂O₃ was found to be in the range of 1–8 × 10⁻⁹ m², which is in the order of magnitude of gas filters, and, therefore, suitable for several technological applications.     

Phase Equilibria in the Spinel Region of the System FeO-Fe2O3-Al2O3

Phase relations in the spinel region of the system FeO-Fe₂O₃-Al₂O₃ were determined in CO₂ at 1300°, 1400°, and 15000°C and for partial oxygen pressures of 4 × 10⁻⁷ and 7 × 10⁻¹⁰ atmospheres at 15OO°C. The spinel field extends continuously from Fe₃O_4-x to FeAl₂O_4+z.     

Metastable Crystal Structure of Strontium- and Magnesium-Substituted LaGaO3

The metastable crystal structure of strontium- and magnesium-substituted LaGaO₃ (LSGM) was studied at room and intermediate temperatures using powder X-ray diffractometry and Rietveld refinement analysis. With increased strontium and magnesium content, phase transitions were found to occur from orthorhombic (space group Pbnm ) to rhombohedral (space group R [Threemacr] c ) at the composition La_0.825Sr_0.175Ga_0.825Mg_0.175O_2.825 and, eventually, to cubic (space group Pm [Threemacr] m ) at the composition La_0.8Sr_0.2Ga_0.8Mg_0.2O_2.8. At 500°C in air and at constant strontium and magnesium content, a phase transformation from orthorhombic (space group Pbnm ) to cubic (space group Pm [Threemacr] m ) was observed. For the orthorhombic modification, thermal expansion coefficients were determined to be α _a ,ortho = 10.81 × 10⁻⁶ K⁻¹, α _b ,ortho = 9.77 × 10⁻⁶ K⁻¹, and α _c ,ortho = 9.83 × 10⁻⁶ K⁻¹ (25°–400°C), and for the cubic modification to be α_cubic= 13.67 × 10⁻⁶ K⁻¹ (500°–1000°C).     

Thermal Expansion of the Low-Temperature Form of BaB2O4

Thermal expansion of the low-temperature form of BaB₂O₄ (β-BaB₂O₄) crystal has been measured along the principal crystallographic directions over a temperature range of 9° to 874°C by means of high-temperature X-ray powder diffraction. This crystal belongs to the trigonal system and exhibits strongly anisotropic thermal expansions. The expansion along the c axis is from 12.720 to 13.214 Å (1.2720 to 1.3214 nm), whereas it is from 12.531 to 12.578 Å (1.2531 to 1.2578 nm) along the a axis. The expansions are nonlinear. The coefficients A, B , and C in the expansion formula L _t = L ₀(1 + At + Bt ²+ Ct ³) are given as follows: a axis, A = 1.535 × 10⁻⁷, B = 6.047 × 10⁻⁹, C = -1.261 × 10⁻¹²; c axis, A = 3.256 × 10⁻⁵, B = 1.341 × 10⁻⁸, C = -1.954 × 10⁻¹²; and cell volume V, A = 3.107 × 10⁻⁵, B = 3.406 × 10⁻⁸, C = -1.197 × 10⁻¹¹. Based on α _t = (d L _t /d t )/ L ₀, the thermal expansion coefficients are also given as a function of temperature for the crystallographic axes a , c , and cell volume V.     

Transformation, Microstructure Development, and Densification in α-Fe2O3-Seeded Boehmite-Derived Alumina

Addition of α-Fe₂O₃ seed particles to alkoxide-derived boehmite sols resulted in a 10-fold increase in isothermal rate constants for the transformation of γ- to α-Al₂O₃. Changes in porosity and surface area with sintering temperature showed no effect of seeding on coarsening of the transition alumina gels, but the 200-fold decrease in surface area associated with transformation to α-Al₂O₃ occurred ∼ 100°C lower in seeded gels compared with unseeded materials. As a result of high nucleation frequency and reduced microstructure coarsening, fully transformed seeded alumina retained specific surface areas >22 m²/g and exhibited narrow pore size distributions, permitting development of fully dense, submicrometer α-Al₂O₃ at ∼ 1200°C.     

Influence of Cr and Fe on Formation of α-Al2O3 from γ-Al2O3

The effect of Cr and Fe in solid solution in γ-Al₂O₃ on its rate of conversion to α-Al₂O₃ at 1100°C was studied by X-ray diffraction. The δ form of Al₂O₃ was the principal intermediate phase produced from both pure γ-Al₂O₃ and that containing Fe³⁺ in solid solution, although addition of Fe greatly reduced crystallinity. Reflectance spectra and magnetic susceptibilities showed that Cr exists as Cr⁶⁺ in γ-Al₂O₃ and as Cr³⁺ in α-Al₂O₃, with θ-Al₂O₃ as the intermediate phase. The intermediates formed rapidly, and the rates of their conversion to α-Al₂O₃ were increased by 2 and 5 wt% additions of Fe and decreased by 2 and 4 wt% additions of Cr. An approximately linear relation observed between α-Al₂O₃ formation and decrease in specific surface area was only slightly affected by the added ions. This relation can be explained by a mechanism in which the sintering of δ- or θ-Al₂O₃, within the aggregates of their crystallites, is closely coupled with conversion of cubic to hexagonal close packing of O^2- ions by synchro-shear.     

Anisotropic Thermal Expansion of β-Ca2SiO4 Monoclinic Crystal

Crystals of β-Ca₂SiO₄ (space group P 12₁/ n 1) were examined by high-temperature powder X-ray diffractometry to determine the change in unit-cell dimensions with temperature up to 645°C. The temperature dependence of the principal expansion coefficients (α_i) found from the matrix algebra analysis was as follows: α₁= 20.492 × 10⁻⁶+ 16.490 × 10⁻⁹ ( T - 25)°C⁻¹, α₂= 7.494 × 10⁻⁶+ 5.168 × 10⁻⁹( T - 25)°C⁻¹, α₃=−0.842 × 10⁻⁶− 1.497 × 10⁻⁹( T - 25)°C⁻¹. The expansion coefficient α₁, nearly along [302] was approximately 3 times α₂ along the b -axis. Very small contraction (α₃) occurred nearly along [     01]. The volume changes upon martensitic transformations of β↔α_L' were very small, and the strain accommodation would be almost complete. This is consistent with the thermoelasticity.     

Preliminary Observations on Phase Relations in the "V2O3–FeO" and V2O3–TiO2 Systems from 1400°C to 1600°C in Reducing Atmospheres

Phase relations within the "V₂O₃–FeO" and V₂O₃–TiO₂ oxide systems were determined using the quench technique. Experimental conditions were as follows: partial oxygen pressures of 3.02 × 10⁻¹⁰, 2.99 × 10⁻⁹, and 2.31 × 10⁻⁸ atm at 1400°, 1500°, and 1600°C, respectively. Analysis techniques that were used to determine the phase relations within the reacted samples included X-ray diffractometry, electron probe microanalysis (energy-dispersive spectroscopy and wavelength-dispersive spectroscopy), and optical microscopy. The solid-solution phases M₂O₃, M₃O₅, and higher Magneli phases (M _n O_{2 n −1}, where M = V, Ti) were identified in the V₂O₃–TiO₂ system. In the "V₂O₃–FeO" system, the solid-solution phases M₂O₃ and M₃O₄ (where M = V, Ti), as well as liquid, were identified.     

Formation of Frozen α-Agl in Twin-Roller-Quenched Agl─Ag2 O─MxOy (MxOy= WO3, V2O5) Glasses at Ambient Temperature

Superionic conductor α-AgI, which is stable only above 147°C, was successfully frozen at ambient temperature in AgI─Ag₂O─M_xO_y (M_xO_y= WO₃, V₂O₅) glass matrices by a twin-roller-quenching technique. The system with WO₃, provided the larger composition regions where α-AgI was frozen at ambient temperature, compared to the system with V₂O₅. The matrix glasses with higher glass-transition temperatures had a stronger effect in depressing the α–β transformation of AgI. The α-AgI-frozen samples exhibited extremely large conductivities of 3 × 10⁻²-5 × 10⁻²S.cm⁻¹at 25°C.     

Nanocrystalline α-Al2O3 Using Sucrose

Nanocrystalline α-Al₂O₃ ceramic powders have been prepared from an aqueous solution of aluminum nitrate and sucrose. Soluble Al ion-sucrose solution forms the precursor material once it is completely dehydrated. Heat treatment of the dehydrated precursors at low temperature (600°C) results in the formation of porous single-phase α-Al₂O₃. The precursor and heat-treated powders have been characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and BET surface area analysis. The phase-pure nanocrystalline α-Al₂O₃ particles had an average specific surface area of >190 m²/g, with an average pore size between 18 and 25 nm.     

Phase Diagram of a Nickel-Zinc Ferrite of Composition Ni0.685Zn0.177Fe2.138O4+γ

The oxygen content of Ni_0.685Zn_0.177Fe_2.138O_4+γ was determined gravimetrically at atmospheric pressure in varying Po₂ , 3.5 × 10⁻⁴ to 1.0 atm at 600° to 1450°C. The phase boundary associated with the precipitation of α-Fe₂O₃ was determined from the change in slope of γ vs T plots observed on heating. Metastability is particularly evident for curves observed on cooling. Isacompositional lines (0.002 < γ < 0.045) are shown on a plot of log PO₂ vs 1/T. An enthalpy of -21.6 kcal/mol is calculated for the oxidation of Fe²⁺.     

Growth of Tabular α-Al2O3 Grains on Porous Alumina Substrate

Gradient, porous alumina ceramics were prepared with the characteristics of microsized tabular α-Al₂O₃ grains grown on a surface with a fine interlocking feature. The samples were formed by spin-coating diphasic aluminosilicate sol on porous alumina substrates. The sol consisted of nano-sized pseudo-boehmite (AlOOH) and hydrolyzed tetraethyl orthosilicate [Si(OC₂H₅)₄]. After drying and sintering at 1150°–1450°C, the crystallographic and chemical properties of the porous structures were investigated by analytical electron microscopy. The results show that the formation of tabular α-Al₂O₃ grains is controlled by the dissolution of fine Al₂O₃ in the diphasic material at the interface. The nucleation and growth of tabular α-Al₂O₃ grains proceeds heterogeneously at the Al₂O₃/glass interface by ripening nano-sized Al₂O₃ particles.     

Deviation from Stoichiometry in Cr2O3 at High Oxygen Partial Pressures

The deviation from stoichiometry, δ, in Cr₂−δO₃ was measured by a tensivolumetric method in the high pO₂ range of ≊10⁴ to 10⁴ Pa at 1100°C. The value of δ, or chromium vacancy concentration, was≊9×10⁻⁵ mol/mol Cr₂O₃ in air for Cr₂O₃ with 99.999% purity. The chemical diffusion coefficient, DT, determined from equilibration data was ≊4.6× cm²·s⁻¹ at 1100°C for pO₂= 2.2 ×10¹ Pa. The self-diffusion coefficient of Cr ions was calculated from and δ and found to be≊1.6×10-17 cm²-s⁻¹, in good agreement with recently measured values.     

Thermal Expansion of Pb3O4

Thermal expansion of Pb₃O₄ was investigated by high-temperature X-ray diffraction. The coefficient in the a ₀ direction is 14.6×10⁻⁶/°C. Expansion in the c₀ direction is 32% greater, with a coefficient of 19.3×10⁻⁶/°C. Coefficients of expansion are linear from 25° to 490°C and are comparable with those of tetragonal and orthorhombic PbO.     

Vapor Pressure of Barium and Copper Components in YBa2Cu3O7−x Superconductor Ceramics

Purified air is passed over a specimen of YBa₂Cu₃O_{7– x} at 890°C; the vaporized substances are condensed in a pure alumina tube, then subjected to inductively controlled plasma analysis. Vapor pressure values of 2.5 × 10⁻⁵ Pa for BaO( g ), 1.2 × 10⁻⁴ Pa for Cu( g ), and 2.2 × 10⁻⁵ Pa for CuO( g ) are obtained under 2.1 × 10⁴ Pa (0.21 bar) of oxygen pressure. No Y vapor is detected at this temperature.     

Preparation of a Highly Conductive Al2O3/TiN Interlayer Nanocomposite through Selective Matrix Grain Growth

An electroconductive TiN/Al₂O₃ nanocomposite was prepared by a selective matrix grain growth method, using a powder mixture of submicrosized α-Al₂O₃, nanosized γ-Al₂O₃, and TiN nanoparticles synthesized through an in situ nitridation process. During sintering, a self-concentration of TiN nanoparticles at the matrix grain boundary occurred, as a result of the selective growth of large α-Al₂O₃ matrix grains. Under suitable sintering conditions, a typical interlayer nanostructure with a continuous nanosized TiN interlayer was formed along the Al₂O₃ matrix grain boundary, and the electroconducting behavior of the material was significantly improved. Twelve volume percent TiN/Al₂O₃ nanocomposite with such an interlayer nanostructure showed an unprecedentedly low resistivity of 8 × 10⁻³Ω·cm, which was more than two orders lower than the TiN/Al₂O₃ nanocomposite without such an interlayer nanostructure.     

Microstructure and Mechanical Properties of Hot-Pressed α-Al2O3-Seeded γ-Alumina Ceramics

High-quality alumina ceramics were fabricated by a hot pressing with MgO and SiO₂ as additives using α-Al₂O₃-seeded nanocrystalline γ-Al₂O₃ powders as the raw material. Densification behavior, microstructure evolution, and mechanical properties of alumina were investigated from 1250°C to 1450°C. The seeded γ-Al₂O₃ sintered to 98% relative density at 1300°C. Obvious grain growth was observed at 1400°C and plate-like grains formed at 1450°C. For the 1350°C hot-pressed alumina ceramics, the grain boundary regions were generally clean. Spinel and mullite formed in the triple-grain junction regions. The bending strength and fracture toughness were 565 MPa and 4.5 MPa·m^1/2, respectively. For the 1300°C sintered alumina ceramics, the corresponding values were 492 MPa and 4.9 MPa·m^1/2.     

Electrical Conduction in Single-Crystal and Polycrystalline Al2O3 at High Temperatures

The electrical conductivity and ion/electron transference numbers in Al₃O₃ were determined in a sample configuration designed to eliminate influences of surface and gas-phase conduction on the bulk behavior. With decreasing O₂ partial pressure over single-crystal Al₂O₃ at 1000° to 1650°C, the conductivity decreased, then remained constant, and finally increased when strongly reducing atmospheres were attained. The intermediate flat region became dominant at the lower temperatures. The emf measurements showed predominantly ionic conduction in the flat region; the electronic conduction state is exhibited in the branches of both ends. In pure O₂ (1 atm) the conductivity above 1400°C was σ≃3×10³ exp (–80 kcal/ RT ) Ω⁻¹ cm⁻¹, which corresponds to electronic conductivity. Below 1400°C, the activation energy was <57 kcal, corresponding to an extrinsic ionic condition. Polycrystalline samples of both undoped hot-pressed Al₂O₃ and MgO-doped Al₂O₃ showed significantly higher conductivity because of additional electronic conduction in the grain boundaries. The gas-phase conduction above 1200°C increased drastically with decreasing O₂ partial pressure (below 10⁻¹⁰ atm).     

Tribological Behavior of Ti2SC at Ambient and Elevated Temperatures

The tribological properties of Ti₂SC were investigated at ambient temperatures and 550°C against Ni-based superalloys Inconel 718 (Inc718) and alumina (Al₂O₃) counterparts. The tests were performed using a tab-on-disk method at 1 m/s and 3N (≈0.08 MPa). At room temperature, against the superalloy, the coefficient of friction, μ, was ∼0.6, and at ∼8 × 10⁻⁴ mm³·(N·m)⁻¹ the specific wear rate (SWRs), was high. However, against Al₂O₃, at ∼5 × 10⁻⁵ mm³·(N·m)⁻¹ and ∼0.3, the SWRs and μ were significantly lower, which was presumably related to more intensive tribo-oxidation at the contact points. At 550°C, the Ti₂SC/Inc718 and Al₂O₃ tribocouples demonstrated comparable μ's of ∼0.35–0.5 and SWRs of ∼7–8 × 10⁻⁵ mm³·(N·m)⁻¹. At 550°C, all tribosurfaces were covered by X-ray amorphous oxide tribofilms. At present, Ti₂SC is the only member of a family of the layered ternary carbides and nitrides (MAX phases) that can be used as a tribo-partner against Al₂O₃ in the wide temperature range from ambient to 550°C.     

Electrical Conduction in Nano-Structured La0.9Sr0.1Al0.85Co0.05Mg0.1O3 Perovskite Oxide

Nanocrystalline La_0.9Sr_0.1Al_0.85Co_0.05Mg_0.1O₃ oxide powder was synthesized by a citrate–nitrate auto-ignition process and characterized by thermal analysis, X-ray diffraction, and impedance spectroscopy measurements. Nanocrystalline (50–100 nm) powder with perovskite structure could be produced at 900°C by this process. The powder could be sintered to a density more than 96% of the theoretical density at 1550°C. Impedance measurements on the sintered samples unequivocally established the potential of this process in developing nanostructured lanthanum aluminate-based oxides. The sintered La_0.9Sr_0.1Al_0.85Co_0.05Mg_0.1O₃ sample exhibited a conductivity of 2.40 × 10⁻² S/cm in air at 1000°C compared with 4.9 × 10⁻³ S/cm exhibited by La_0.9Sr_0.1Al_0.85Mg_0.15O₃.