Synthesis and characterisation of copolyesters from poly(ethylene terephthalate) and poly(hexamethylene terephthalate)

Copolyesters containing poly(ethylene terephthalate) and poly(hexamethylene terephthalate) (PHT) were prepared by a melt condensation reaction. The copolymers were characterised by infrared spectroscopy and intrinsic viscosity measurements. The density of the copolyesters decreased with increasing percentage of PHT segments in the backbone. Glass transition temperatures (T_g). melting points (T_m) and crystallisation temperatures (T_c) were determined by differential scanning calorimetry. An increase in the percentage of PHT resulted in decrease in T_g, T_m and T_c. The as-prepared copolyesters were crystalline in nature and no exotherm indicative of cold crystallisation was observed. The relative thermal stability of the polymers was evaluated by dynamic thermogravimetry in a nitrogen atmosphere. An increase in percentage of PHT resulted in a decrease in initial decomposition temperature. The rate of crystallisation of the copolymers was studied by small angle light scattering. An increase in percentage of PHT resulted in an increase in the rate of crystallisation.     

Synthesis and characterization of aspartate polymer complexes

Oligomeric polyester, namely poly(tetramethylene asparate) (PTMA), was synthesized From D ,L ‐aspartic acid and 1,4‐butanediol by a melt codensation technique. Polyester–metal complexes were synthesized by the reaction of PTMA with hydrated acetates of Fe(III), Pd(IV), and UO₂(II) in DMSO. The polyester–metal complexes were characterized by elemental analysis, UV–Vis, IR spectral studies, magnetic susceptibility measurements and ¹H‐NMR. Mossbauer spectra of mixed samples of Pd‐PTMA and Fe(II)‐PTMA with a ratio of 1 : 2 mol showed the iron(III) oxide formed in early stages of the decomposition at 250°C is mainly fine‐grained and as the temperature is increased, well‐crystalline hematic is formed. Above 250°C, the Mossbauer spectrum showed the typical six‐line pattern of magnetically oriented Fe(III) oxide, but at 800°C, the spectrum showed quadrupole interaction characteristic of PdFe₂O₄ spinel. The metal ions were found to be six—coordinated with two water molecules as additional ligands besides oxygen and nitrogen atoms of polyester repeating units. Thermogravimetric analysis (DTA‐TG) showed that co‐ordination polymers are thermally more stable than polyester; the activation parameters for both decomposition steps were calculated and discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 942–947, 2004     

Synthesis and characterization of coordination polymers of polyesters with pendant amino groups

Oligomeric polyester, namely, poly(tetramethylene aspartate) (PTMA), was synthesized from D ,L -aspartic acid and 1,4-butanediol by a melt-condensation technique. Polyester–metal complexes were synthesized by the reaction of PTMA with hydrated acetates of Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Cd(II), Hg(II), Mg(II), Ca(II), Pb(II), and Ce(IV) in DMSO. The polyester–metal complexes were characterized by elemental analysis, IR spectral studies, magnetic susceptibility measurements, and thermogravimetry. The metal ions were found to be six-coordinated with two water molecules as additional ligands besides oxygen and nitrogen atoms of polyester repeating units. Thermogravimetric analysis (TGA) showed that coordination polymers are thermally more stable than is polyester. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 751–759, 1998     

聚乙二醇/聚己内酯三嵌段共聚物的合成与表征

以甲苯二异氰酸酯 (TDI)为偶联剂 ,合成了聚乙二醇 (PEG) /聚己内酯 (PCL)两亲性三嵌段共聚物 (PEG-b-PCL -b -PEG ,PECL) ,采用IR、1 H-NMR、DSC和WAXD分析和研究了PECL的结构与性能。实验结果表明 ,PECL的结构和组成与设计相一致 ,结晶度和熔点均低于均聚物 ,且随着PECL中PCL嵌段含量的增加 ,PCL嵌段熔点升高。透射电镜照片显示PECL纳米粒呈核 /壳结构的球形。     

Synthesis and hydrophilicity of poly(butylene 2,6‐naphthalate)/poly(ethylene glycol) copolymers

Poly(butylene 2,6‐naphthalate) (PBN)/poly(ethylene glycol) (PEG) copolymers were synthesized by the two‐step melt copolymerization process of dimethyl‐2,6‐naphthalenedicarboxylate (2,6‐NDC) with 1,4‐butanediol (BD) and PEG. The copolymers produced had different PEG molecular weights and contents. The structures, thermal properties, and hydrophilicities of these copolymers were studied by ¹H NMR, DSC, TGA, and by contact angle and moisture content measurements. In particular, the intrinsic viscosities of PBN/PEG copolymers increased with increasing PEG molecular weights, but the melting temperatures (T_m)_, the cold crystallization temperatures (T_cc)_, and the heat of fusion (ΔH_f) values of PBN/PEG copolymers decreased on increasing PEG contents or molecular weights. The thermal stabilities of the copolymers were unaffected by PEG content or molecular weight. Hydrophilicities as determined by contact angle and moisture content measurements were found to be significantly increased on increasing PEG contents and molecular weights. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2677–2683, 2006     

导电聚合物PEDOT/PSS-MPEG的制备及性能

引言导电高分子既有导体材料的光电学特性,又有良好的力学性能和可加工性[1],这使得导电高分子材料具有广泛的应用前景。聚噻吩类有机导电材料[2]就是这类材料中的一种。聚噻吩的室温电导率     

High molecular weight poly( -lactide) and poly(ethylene oxide) blends: thermal characterization and physical properties

The miscibility of high molecular weight poly( -lactide) PLLA with high molecular weight poly(ethylene oxide) PEO was studied by differential scanning calorimetry. All blends containing up to 50 weight% PEO showed single glass transition temperatures. The PLLA and PEO melting temperatures were found to decrease on blending, the equilibrium melting points of PLLA in these blends decreased with increasing PEO fractions. These results suggest the miscibility of PLLA and PEO in the amorphous phase. Mechanical properties of blends with up to 20 weight% PEO were also studied. Changes in mechanical properties were small in blends with less than 10 weight% PEO. At higher PEO concentrations the materials became very flexible, an elongation at break of more than 500% was observed for a blend with 20 weight% PEO. Hydrolytic degradation up to 30 days of the blends showed only a small variation in tensile strength at PEO concentrations less than 15 weight%. As a result of the increased hydrophilicity, however, the blends swelled. Mass loss upon degradation was attributed to partial dissolution of the PEO fraction and to an increased rate of degradation of the PLLA fraction. Significant differences in degradation behaviour between PLLA/PEO blends and (PLLA/PEO/PLLA) triblock-copolymers were observed.     

Synthesis and characterization of poly(methylphenylsilylene)–poly(ethylene oxide) and poly(methylphenylsilylene)–polyisoprene multiblock copolymers

Multiblock copolymers were synthesized through condensation reactions of end‐groups of α,ω‐dichloro‐poly(methylphenylsilylene) with hydroxyl end‐groups of poly(ethylene glycol) or the chain‐ends of ‘living’ polyisoprenyl disodium. Optimum conditions have been sought through kinetic studies and by investigation of model reactions. The overall molecular weight distribution of poly(methylphenylsilylene)‐block‐poly(ethylene oxide) is characterized in terms of Flory's theory of condensation reactions, while the limiting step in the reaction is tentatively attributed to the formation of aggregates. © 2001 Society of Chemical Industry     

异端基遥爪聚乙二醇的合成

采用3种新式引发剂,即2-(苄氧基）乙醇钾、2-(四氢-2H-吡喃-2-氧基)乙醇钾、单丙烯基乙二醇钾引发环氧乙烷阴离子开环聚合,反应条件为25 ℃、48 h、醇与萘钾摩尔比例1∶1,得到3种异端基遥爪聚乙二醇。以2-(苄氧基）乙醇钾引发聚合所得产物为起始物,经一系列反应,得到两种两端均为活性基团的异端基遥爪聚乙二醇,这种方法具有普适性。通过1HNMR及GPC手段,表征了产物的结构、分子量及分子量分布。结果表明可以得到高产率、分子量可控且分布窄的异端基遥爪聚乙二醇。     

Synthesis and characterization of poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers

Poly(L‐lactide)‐poly(ethylene glycol) multiblock copolymers with predetermined block lengths were synthesized by polycondensation of PLA diols and PEG diacids. The reaction was carried out under mild conditions, using dicyclohexylcarbodiimide as the coupling agent and dimethylaminopyridine as the catalyst. The resulting copolymers were characterized by various analytical techniques, such as GPC, viscometry, ¹H‐NMR, FTIR, DSC, X‐ray diffractometry, and contact angle measurement. The results indicated that these copolymers presented outstanding properties pertinent to biomedical use, including better miscibility between the two components, low crystallinity, and hydrophilicity. Moreover, the properties of the copolymers can be modulated by adjusting the block length of the two components or the reaction conditions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1729–1736, 2002; DOI 10.1002/app.10580     

Synthesis and characterization of poly(methylene disulfide) and poly(ethylene disulfide) polymers in the presence of a phase transfer catalyst

Poly(methylene disulfide) and poly(ethylene disulfide) were synthesized from the polycondensation of methylene dichloride and ethylene dichloride monomers, respectively, in the presence of benzyltriethylammonium chloride as a phase transfer catalyst. The structures of the synthesized polysulfides were confirmed via the elemental analysis, attenuated total reflectance Fourier transform infrared spectroscopy and X-ray diffraction techniques. Moreover, the thermal behaviors of synthesized poly(methylene disulfide) and poly(ethylene disulfide) were characterized using differential scanning calorimetry and thermogravimetric analysis methods. The synthesized poly(methylene disulfide) and poly(ethylene disulfide) have molecular weights of about 2262 and 2863 g/mol, respectively. In addition, the polymers have crystalline structures absorbed in the amorphous sections. However, the d-spacing of polymers’ crystalline parts was different. Moreover, poly(methylene disulfide) and poly(ethylene disulfide) have a two- and one-step degradation behavior, respectively.     

Polymer distribution during bicomponent melt blowing of poly(propylene)/poly(ethylene terephthalate) and its improvement

Bicomponent melt blown (MB) microfiber nonwovens of poly(propylene) (PP) and poly(ethylene terephthalate) (PET) were produced in this study. It is interesting to analyze the polymer distribution uniformity across the web because it affects many end‐use properties. By utilizing the technique of differential scanning calorimetry (DSC), a standard working line between heat of fusion and weight percentage was constructed for mixtures of PP and PET components. The fitted equations were used for determination of a component percentage in a certain position across the MB web. Measurements were conducted from DSC re‐heating curves to achieve accurate results. The distribution of polymer varies with polymer mass ratio and processing conditions. The overall uniformity increased with the percentage of PP. When PP is the minor component in the polymer pair, it exhibits notably higher percentage in edge areas across the MB web. These results suggest the phase interface distortion of the polymer melt occurred at the entrance of the MB coat‐hanger die tip. The polymer distribution uniformity is improved by adjusting temperature profile of the MB die. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2885–2889, 2002     

Synthesis and characterization of poly(ethylene terephthalate)/attapulgite nanocomposites

A kind of clay with fibrous morphology, attapulgite (AT), was used to prepare poly (ethylene terephthalate) (PET)/AT nanocomposites via in situ polymerization. Attapulgite was modified with Hexadecyltriphenylphosphonium bromide and silane coupling agent (3‐glycidoxypropltrimethoxysilane) to increase the dispersion of clay particles in polymer matrix and the interaction between clay particles and polymer matrix. FTIR and TGA test of the organic‐AT particles investigated the thermal stability and the loading quantity of organic reagents. XRD patterns and SEM micrographs showed that the organic modification was processed on the surface of rod‐like crystals and did not shift the crystal structure of silicate. For PET/AT nanocomposites, it was revealed in TEM that the fibrous clay can be well dispersed in polymer matrix with the rod‐like crystals in the range of nanometer scale. The diameter of rod‐like crystal is about 20 nm and the length is near to 500 nm. The addition of the clay particles can enhance the thermal stability and crystallization rate of PET. With the addition of AT in PET matrix, the flexural modulus of those composites was also increased markedly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1279–1286, 2007     

Blends of poly(ethylene terephthalate) and poly(butylene terephthalate)

Commercial grade poly(ethylene terephthalate), (PET, intrinsic viscosity = 0.80 dL/g) and poly(butylene terephthalate), (PBT, intrinsic viscosity = 1.00 dL/g) were melt blended over the entire composition range using a counterrotating twin‐screw extruder. The mechanical, thermal, electrical, and rheological properties of the blends were studied. All of the blends showed higher impact properties than that of PET or PBT. The 50:50 blend composition exhibited the highest impact value. Other mechanical properties also showed similar trends for blends of this composition. The addition of PBT increased the processability of PET. Differential scanning calorimetry data showed the presence of both phases. For all blends, only a single glass‐transition temperature was observed. The melting characteristics of one phase were influenced by the presence of the other. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 75–82, 2005     

Toughening of bismaleimide resin by modification with poly(ethylene phthalate) and poly(ethylene phthalate-co-ethylene isophthalate)

Aromatic polyesters were prepared and used to improve the brittleness of the bismaleimide resin composed of 4,4′-bismaleimidediphenyl methane and o,o′-diallyl bisphenol A. The aromatic polyesters contain poly(ethylene phthalate) (PEP) and poly(ethylene phthalate-co-ethylene isophthalate) (10 mol % isophthalate unit) (PEPI). PEP and PEPI were effective modifiers for improving the brittleness of the bismaleimide resin. The most suitable composition for the modification of the bismaleimide was inclusion of 20 wt % PEP (MW 18,200), which led to an 80% increase in the fracture toughness with retention of flexural properties and a slight decrease in the glass transition temperature, compared with the mechanical and thermal properties of the unmodified cured bismaleimide resin (Matrimid resin). Microstructures of the modified resins were examined by scanning electron microscopy and dynamic viscoelastic analysis. The thermal stability of the modified resin was slightly lower than that of the unmodified resin by thermogravimetric analysis. The toughening mechanism is discussed in terms of the morphological and dynamic viscoelastic behavior of the modified bismaleimide resin system. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 1349–1357, 1997     

PEN/PET共混物结晶行为研究

用差示扫描量热法(DSC)研究了不同共混比例PEN/PET共混物的熔体结晶行为,并进行了等温结晶动力学测定。结果表明:随着两种组分向中间比例(50/50)靠近,共混物的熔融温度越低,结晶速率也越慢。     

Effect of poly(ethylene glycol) on the solid‐state polymerization of poly(ethylene terephthalate)

Poly(ethylene glycol) (PEG) and end‐capped poly(ethylene glycol) (poly(ethylene glycol) dimethyl ether (PEGDME)) of number average molecular weight 1000 g mol^?1 was melt blended with poly(ethylene terephthalate) (PET) oligomer. NMR, DSC and WAXS techniques characterized the structure and morphology of the blends. Both these samples show reduction in T_g and similar crystallization behavior. Solid‐state polymerization (SSP) was performed on these blend samples using Sb₂O₃ as catalyst under reduced pressure at temperatures below the melting point of the samples. Inherent viscosity data indicate that for the blend sample with PEG there is enhancement of SSP rate, while for the sample with PEGDME the SSP rate is suppressed. NMR data showed that PEG is incorporated into the PET chain, while PEGDME does not react with PET. Copyright © 2005 Society of Chemical Industry     

Melt‐electrospinning of poly(ethylene terephthalate) and polyalirate

Rodlike polymer samples were made from three kinds of poly(ethylene terephthalate) (PET) pellets with different intrinsic viscosities (IV), and from polyalirate (Vectra) pellets. PET and Vectra fibers were produced using a melt‐electrospinning system equipped with a CO₂‐laser melting device from these rodlike samples. The effects of IV value and laser output power on the fiber diameter of PET were investigated. Furthermore, the effect of the laser output power on the fiber diameter of Vectra was investigated. The crystal orientation of these produced fibers was also investigated by X‐ray photographs. The following conclusions were reached: (i) the diameter of PET fiber decreases with increasing laser output power; (ii) the minimum average diameter of PET fibers is scarcely influenced by the value of IV; (iii) the electrospun PET fibers show isotropic crystal orientation; (iv) fibers having an average fiber diameter smaller than 1 μm cannot be obtained from PET and Vectra using the system developed; and (v) preferred liquid crystal orientation can be seen in electrospun Vectra fibers. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and properties of poly(ethylene-1,4-cyclohexanedimethylene naphthalate)

Copolyesters were synthesized from bis(hydroxyethyl) naphthalate/bis(hydroxymethylcyclohexane)naphthalate (BHEN/BHCN) with various compositions. Copolyesters having intrinsic viscosities of 0.58–0.65 dL g were obtained by melt polycondensation in the presence of metallic catalysts. The optimum condition for polyethylene-1,4-cyclohexanedimethylene naphthalate (PECN) copolyester manufacturing is the transesterification under a nitrogen atmosphere for 4 h at a temperature of 245 ± 5°C followed by polymerization under 2 mmHg for 50 min at a temperature of 290–320°C. Most copolyesters have better thermal stability than has poly(ethylene naphthalate) (PEN) and the effect of the cyclohexane–dimethylene structure on the thermal and crystalline properties of the resulting copolyesters was investigated using differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). Glass transition temperatures of the copolyesters were in the range of 115.2–138.4°C, and 10% weight losses in nitrogen were all above 453°C. The solubility, crystallinity, and moisture absorption of the copolyesters were also investigated. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:2245–2252, 1998     

Biodegradability of poly(ethylene terephthalate) copolymers with poly(ethylene glycol)s and poly(tetramethylene glycol)

Poly(ethylene terephthalate) copolymers were prepared by melt polycondensation of dimethyl terephthalate and excess ethylene glycol with 10–40mol% (in feed) of poly(ethylene glycol) (E) and poly(tetramethylene glycol) (B), with molecular weight (MW) of E and B 200–7500 and 1000, respectively. The reduced specific viscosity of copolymers increased with increasing MW and content of polyglycol comonomer. The temperature of melting (T_m), cold crystallization and glass transition (T_g) decreased with the copolymerization. T_m depression of copolymers suggested that the E series copolymers are the block type at higher content of the comonomer. T_g was decreased below room temperature by the copolymerization, which affected the crystallinity and the density of copolymer films. Water absorption increased with increasing content of comonomer, and the increase was much higher for E1000 series films than B1000 series films. The biodegradability was estimated by weight loss of copolymer films in buffer solution with and without a lipase at 37°C. The weight loss was enhanced a little by the presence of a lipase, and increased abruptly at higher comonomer content, which was correlated to the water absorption and the concentration of ester linkages between PET and PEG segments. The weight loss of B series films was much lower than that of E series films. The abrupt increase of the weight loss by alkaline hydrolysis is almost consistent with that by biodegradation.