基于大数据分析的废旧塑料利用率算法

概述了我国废旧塑料再生利用现状及应用领域,通过大数据回归分析建立了废旧塑料利用率的算法模型,测算我国2009—2019年的废旧塑料利用率.2009—2014年,废旧塑料利用率从12.0％升至16.0％,2015—2019年略微下降.2009—2015年,塑料回收利用量持续增长,2016年,回收利用量有所下降,2017—...     

Consolidation of sand formation using freon'll gas hydrate

Freon 11 gas hydrate was used to block the pores of four size ranges of sand from 24 mesh to 60 mesh. A 50.8 mm deep bed of sand when thus “frozen” with hydrate could sustain a dfferential water pressure of at least 6895 kPa. A subcooling of about 5 to 6°C below its thermodynamic formation temperature was required to cause the hydrate to form such a plug. Once formed, the hydrate remained stable at temperatures up to its decomposition temperature. The time required for the hydrate crystal to grow to a size large enough to block the pores of the bed was about two hours. The amount of hydrate forming agent required to block the sand pores was found to be approximately that calculated from the ideal composition of the hydrate.     

Adhesives in construction: A contractor's viewpoint

The development of epoxy- and polyester-based adhesives has dramatically widened the scope of adhesive bonding in the civil engineering industry but the technology of the adhesives used has often been more appropriate to the workshop than to the construction site. There is a need for the suppliers of structural adhesives to recognize this and to develop compositions and application techniques more amenable to site use. It is equally necessary for the construction industry to make more effort to understand these materials, to take advantage of their outstanding properties, and hence to use them successfully for the construction and repair of concrete structures.     

Developments in coatings for military vehicles

Conclusions  The MOD operates a wide range of transportation equipment and to ensure that these systems are able to operate in a range of environments a suite of advanced coatings are needed. Environmental legislation has provided a major impetus to introduce new coatings but in addition to the introduction of materials with low solvent contents it has provided an opportunity to introduce materials with improved performance. Unique to the military environment is the need to develop new materials with specific properties to counteract electromagnetic surveillance techniques. In order to undertake this work, knowledge relating to the interaction of electromagnetic radiation with matter as well as paint technology is needed. A third driver in the pursuit of advanced coatings is the need to seek cost effective technology in an age when government departments are under pressure to provide greatest value for money.     

绿色环保意识的趋向

随着消费者环保意识的提高,人们除了认清绿色环保能对社会和全世界起到巨大的促进作用,还认为绿色环保能够直接、积极地反映其社会地位,在某种程度上反映出消费者自己的绿色环保意识。介绍了消费者对"绿色化"的认识,对"绿色产品"的期望以及生产厂家对"绿色原料"的认证和对"可持续发展"所做的贡献。     

Long-term residual value of North Carolina and Queensland rock phosphates compared with triple superphosphate

The effectiveness of large single applications of North Carolina reactive rock phosphate, Queensland non-reactive rock phosphate, and Calciphos, were compared to the effectiveness of superphosphate in field experiments in south-western Australia for up to 11 years after application. As measured using plant yield, superphosphate was the most effective fertilizer in the year of application, and relative to freshly-applied superphosphate, the effectiveness of the superphosphate residues declined to be about 15 to 65% as effective in the year after application, and 5 to 20% as effective 9 to 10 years after application. Relative to freshly-applied superphosphate, all the rock phosphates were 10 to 30% as effective in the year of application, and the residues remained 2 to 20% as effective in the 10 years after application. The bicarbonate soil test reagent predicted a more gradual decrease in effectiveness of superphosphate of up to 70% 10 years after application. For rock phosphate, the reagent predicted effectiveness to be always lower than for superphosphate, being initially 2 to 11% as effective in the year after application, and from 10% to equally as effective 10 years later. Therefore rock phosphates are unlikely to be economic alternatives to superphosphate in the short or long term on most lateritic soils in south-western Australia.     

The annual cycle of Flehmen in black-tailed deer (Odocoileus hemionus columbianus)

Flehmen is a stereotyped response of ungulates and other mammals to urine. In black-tailed deer, Flehmen occurs typically in males (rarely in females), and its frequency shows an annual cycle. Flehmen in response to female urine was most frequent in November, and to male urine in January. The response minimum to both types of urine occurred in May. Fifty-five to 100% of initial responses to female urine resulted in Flehmen. The deer responded more often to female urine, and the difference between the responses to female and male urine increased from May to November. A male's own urine released Flehmen more often than did urine of other males. The response intensity varied with the spatial orientation of the male to the urinating female, and responses were usually limited to distances of 15 m or less.     

高效、清洁、高附加值原则指导下适度、有序发展煤化工产业

针对我国可持续发展面临的能源瓶颈,指出适度、有序发展煤化工产业是我国现有能源结构环境下的必然选择。在低碳理念指导下,提出了煤炭资源的分质利用原则、高能效利用原则、综合利用原则、因地制宜利用原则和高附加值利用原则,比较分析了煤的各种化学转化途径,阐述了含氧醇醚材料替代石油路线、煤制芳烃、煤/天然气/煤层气制备乙炔等具有前景的清洁、高效转化过程,期望为煤化工产业的健康、有序发展提供科学思路。     

Prediction of gas flow directions in gas assisted injection molding when cavities and runners are involved

In the prediction of gas flow-direction for gas-assisted injection molding (GAIM), the statement“Gas goes to the direction of the last area to fill with resin”, has been accepted as a correct one. When there exists more than one area to fill with resin, a mold design engineer for GAIM technologies has to determine to which direction gas goes that commercial software for GAIM (e.g., Moldflow) may be utilized for its mold design. However commercial software is generally expensive and is sometimes hard to become familiar with. As a rule of thumb, it is suggested that the resistance to the initial velocity of melt polymer at the nearest geometry to a gas injection point should be used as its criterion since gas goes in the direction of least resistance to initial resin-velocity. Neither the flow rate nor the resistance to flow rate can be a criterion in the prediction. Thus the statement“Gas goes to the direction of the least resistance to flow rates”, should be corrected to“More flow rate goes to the direction of the least resistance to flow rates.”, The rule of thumb suggested in this paper was verified by using commercial software, Moldflow, in the prediction of gas flow directions in GAIM under geometries where cavities and runners were involved. When the ratio of initial resin-velocity is so close to unity it is proposed as the adapted rule of thumb to calculate new emerging resin-velocities and resistances to resin-velocity at the first coming change of diameters in series of pipes and to compare those for upper and lower sides each other to predict the gas direction. Thus the judgment as to which point is the point where gas starts to choose a preferred direction is very important in the prediction.     

Glass Formation, a Contemporary View

The process of glass formation is discussed from several perspectives. Particular attention is directed to kinetic treatments of glass formation and to the question of how fast a given liquid must be cooled in order to form a glass. Specific consideration is paid to the calculation of critical cooling rates for glass formation, to the effects of nucleating heterogeneities and transients in nucleation on the critical cooling rates, to crystallization on reheating a glass, to the experimental determination of nucleation rates and barriers to crystal nucleation, and to the characteristics of materials which are most conducive to glass formation.     

生成兴趣的大学教学

大学教育不仅仅是教给学生课本上的知识,更重要的是教会他们学习的方法,如何去获取有用的知识,以及如何利用所学的知识去解决实际问题。如何培养大学低年级学生的学习兴趣,如果引导他们主动去学习,在化学实验课上,又如何主动细致的去完成动手部分的学习,将是我们大学教学工作中急需要改进和提高的重要部分。     

Effect of autoxidation prior to deodorization on oxidative and flavor stability of soybean oil

Summary Oxidation prior to deodorization was shown to be detrimental to the flavor and oxidative stability of soybean oil. The increase in the nonvolatile carbonyl content of freshly deodorized oils was proportional to the peroxide value of the oils before deodorization. Rate of loss of flavor and oxidative stability of the oil were related to the extent of carbonyl development. All oils, whether or not they had been submitted to any known oxidation, contained some nonvolatile carbonyls. The loss in stability was not due to a loss of the antioxidant tocopherol. Oxidized soybean oil methyl esters were shown to develop nonvolatile carbonyl compounds upon heating at deodorization temperatures. The addition of isolated methyl ester peroxide decomposition products to deodorized soybean oil reduced its flavor and oxidative stability in proportion to the amount added. The results obtained were parallel and similar to those obtained by oxidizing soybean oil prior to deodorization. Flavor deterioration and undesirable flavors were typical of aging soybean oil whether or not the oils were oxidized before deodorization or whether an equivalent amount of nonvolatile thermal decomposition products was added to the oil. These oxidatively derived, nonvolatile carbonyl materials are believed to enter into the sequence of reactions that contribute to flavor instability and quality deterioration of soybean oil. The structure of these materials is not know. This work indicates the importance of minimizing autoxidation in soybean oil particularly before deodorization to insure good oxidative and flavor stability. Presented at fall meeting, American Oil Chemists’ Society, October 20–22, 1958, Chicago, Ill. This is a laboratory of the Northern Utilization Research and Development Division, Agricultural Research Service, U. S. Department of Agriculture.     

What Can Computational Modeling Tell Us about the Diversity of Odor-Capture Structures in the Pancrustacea?

A major transition in the history of the Pancrustacea was the invasion of several lineages of these animals onto land. We investigated the functional performance of odor-capture organs, antennae with olfactory sensilla arrays, through the use of a computational model of advection and diffusion of odorants to olfactory sensilla while varying three parameters thought to be important to odor capture (Reynolds number, gap-width-to-sensillum-diameter ratio, and angle of the sensilla array with respect to oncoming flow). We also performed a sensitivity analysis on these parameters using uncertainty quantification to analyze their relative contributions to odor-capture performance. The results of this analysis indicate that odor capture in water and in air are fundamentally different. Odor capture in water and leakiness of the array are highly sensitive to Reynolds number and moderately sensitive to angle, whereas odor capture in air is highly sensitive to gap widths between sensilla and moderately sensitive to angle. Leakiness is not a good predictor of odor capture in air, likely due to the relative importance of diffusion to odor transport in air compared to water. We also used the sensitivity analysis to make predictions about morphological and kinematic diversity in extant groups of aquatic and terrestrial crustaceans. Aquatic crustaceans will likely exhibit denser arrays and induce flow within the arrays, whereas terrestrial crustaceans will rely on more sparse arrays with wider gaps and little-to-no animal-induced currents.     

氟涂料大热背后的冷思

氟涂料因其超强的耐候性和耐沾污性能得到了业界的热烈追捧,尤其是常温交联固化FEVE涂料更是成为工业防腐领域的应用热点。本文汇总了国内外相关技术资料,分析了氟涂料高速发展背后存在的问题,阐述了应如何促进我国氟涂料健康发展。     

Polymers for use in drug delivery—property and structure requirements

The purpose of this paper is to discuss some of the requirements placed on materials needed for improved administration of drugs. Emphasis is placed on macromolecules that need to be designed and prepared to perform specific pharmacological functions, particularly to act as vehicles for delivering drugs to specific locations within the body. After introducing the reasons for more selective drug delivery, and explaining the rationale for using macromolecules, practical examples of results with linking drugs to polymers, modifying polymers to increase their biological compatibility, attachment to polymers of groups that could mediate their specific recognition, modification of proteins with polymers, and the use of polymer complexes will be given to indicate the areas of need for further development of pharmaceutically useful macromolecules.     

Fracture of mica-reinforced polypropylene: Mica concentration effect

Concepts of post-yield fracture mechanics were used to characterize the crack initiation and propagation resistances of mica-reinforced polypropylene containing different mica concentrations. Although mica addition leads to an apparently brittle composite, the crack initiation resistance is slightly increased with mica concentration up to 10 percent by weight; and significant improvement in crack propagation performance was found for polypropylene reinforced by up to 20 percent of mica in comparison to that of virgin polypropylene. The debonding of the interface between mica flakes and the matrix leads to a micro-ductility ahead of the crack tip in which the matrix is able to pull-out from mica particles and to stretch. This micro-ductility also prevents the brittle, unstable crack propagation, which is due to the coalescence of voids in pure polypropylene. Above 20 percent of mica, the reduction of the effective amount of the matrix material results in a substantial drop in the resistance to crack growth of mica-reinforced polypropylene.     

安克锰锌在荔枝树上施用的残留代谢消解规律与安全性评价

安克锰锌是烯酰吗啉两个异构体和代森锰锌组成的多元混合制剂。试样经粉碎、溶剂浸泡提取、混合柱净化,用气相色谱测定烯酰吗啉和代森锰锌母体(CS2),液相色谱测定代谢物乙撑硫脲(ETU)。仪器最低检出量:烯酰吗啉为1.436×10-12g,代森锰锌母体1.326×10-10g,ETU2.5×10-10g,最低检出浓度依次为0.02、0.025、0.02mg/kg,方法回收率依次为86.4%～90.8%、89.2%～95.9%、89.10%～95.13%;标准偏差为0.53～4.34;变异系数为0.58%～4.62%。安克锰锌在果皮中的消解方程广西和广东分别为C=1.2719e-0.1975T和C=1.045e-0.1972T,半衰期(T/2)均为3.5d;土壤中分别为C=0.8734e-0.1187T和C=0.6171e-0.1146T,半衰期(T/2)=6d;最高剂量250倍、最多施3次,最短距收期7d,在果肉中均未检出,果皮和土壤中的残留仅分别为0.1385～0.1745mg/kg和0.3105～0.3415mg/kg,均低于欧共体规定代森锰锌MRL值0.5mg/kg。     

Prediction of fluidized bed behaviour in the presence of liquid bridges

The need to understand defluidization due to free surface liquid in gas–solid fluidized bed processes gave rise to a study of the effect of addition of non-volatile liquids with different viscosity and surface tension to a cold model gas–solid fluidized bed. The incremental addition of liquid to a fluidized bed of Geldart group B particles was observed, in general, to result in a transition to group A behaviour and eventually to group C behaviour. The BA and AC boundaries are shown to be associated with the balance between the interparticle liquid bridge forces and the fluid drag force. Using liquid bridge forces calculated from measurements of bridge geometry, the ratios of interparticle force to fluid drag force were found to vary between 0.6 and 1.07 for the AC boundary and between 0.02 and 0.06 for the BA transition boundary. Based on this approach, a practical diagram is developed enabling fluid bed behaviour to be predicted from a knowledge of particle, fluid and liquid properties and the quantity of liquid in the bed.     

煤或天然气经甲醇制低碳烯烃工艺研究新进展

由煤或天然气经甲醇制低碳烯烃工艺是解决石油资源紧张、低碳烯烃需求量越来越大等问题的有效路线。介绍了几种有代表性的经甲醇制低碳烯烃工艺,包括美国UOP/Hydro甲醇制烯烃工艺,中国科学院大连化学物理研究所的合成气经由二甲醚制低碳烯烃(SDTO)工艺,德国Lurgi公司的甲醇制丙烯工艺,以及甲醇制烯烃与AtoFina/UOP烯烃裂解的集成工艺;分析了各工艺目前达到的技术指标及最近的技术改进,关注了各工艺近几年的工业化进程。除了SDTO工艺外,其他几种工艺有望在未来几年内实现工业化。国内甲醇制低碳烯烃工艺的开发应借助于流化催化裂化成熟的工程设计经验,同时加大甲醇制烯烃工艺流化床催化剂的开发力度。