The electronic effects of Pr on La1−xPrxNiAl11O19 for CO2 reforming of methane

The CO₂ reforming of CH₄ to synthesis gas by using praseodymium modified hexaaluminate La_1−xPr_xNiAl₁₁O₁₉ (x = 0, 0.2, 0.4, 0.6, 0.8, 1.0) as catalysts was studied. The modifier Pr improved the reducibility and catalytic activity of Ni ions as active component in the hexaaluminate lattices, especially the conversion of CH₄ and CO₂ reached 89.62% and 92.94%, respectively over La_0.8Pr_0.2NiAl₁₁O₁₉. It was found that the addition of Pr can promote the electronic transformation between the Ni ions and the La ions to maintain Ni at a lower valence, which promotes the activation of CH₄.     

Highly oriented diamond growth on SixGe1−x (100) thin films

Highly oriented (100) diamond films have been successfully grown on Si_xGe_1−x (100) thin films by bias enhanced nucleation (BEN) in microwave plasma chemical vapor deposition (MPCVD) system. Raman spectra show the 1332 cm⁻¹ peak which proves the formation of diamond. Diamond nucleation density on Si_xGe_1−x substrate estimated by scanning electron microscopy is higher than 10⁹ cm⁻². The interface between diamond and Si_xGe_1−x substrate was characterized by transmission electron microscopy (TEM). About 20 nm decrease in thickness of the Si_xGe_1−x film was observed after bias enhanced nucleation step. TEM shows the existence of silicon carbide and heteroepitaxial diamond grains grown on Si_xGe_1−x substrate. Characterization from high-resolution TEM on the specimen of short time deposition reveals that a number of epitaxial diamond grains were directly nucleated on Si_xGe_1−x with {111} interplanar spacing ratio of diamond and Si_xGe_1−x of 2:3. The diamond nucleation is found to be preferred on the ridge position of the rough substrate surface. Diamond {100} facets were quickly developed in the early stage of growth.     

Structure and magnetic properties of Fe1−xCox nanowires in self-assembled arrays

Fe_1−xCo_x nanowires in self-assembled arrays with varying compositions were produced by the template-assisted pulsed electrochemical deposition method. The structural and magnetic properties of the arrays were investigated using several experimental techniques. TEM analyses indicated that the nanowires were regular, uniform, 8 μm in length and 50 nm in diameter. The results of X-ray diffraction indicated that the body-centered-cubic (bcc) (α), face-centered-cubic (fcc) (γ), and hexagonal-close-packed (hcp) () Fe–Co phases appeared in different compositions. Magnetic measurements showed that the coercivity and squareness of the hysteresis loops of the Fe_1−xCo_x changed with their compositions, which may be attributable to shape anisotropy. The room temperature ⁵⁷Fe Mössbauer spectra of the arrays of the Fe_1−xCo_x nanowires revealed strong shape anisotropy.     

Highly efficient complete oxidation of dilute benzene over ultrafine Cu0.1Ce0.5Zr0.4O2−δ catalyst in a fluidized bed reactor

Ultrafine Cu_0.1Ce_0.5Zr_0.4O_2−δ catalyst operated in a fluidized bed reactor was found to be very effective for complete oxidation of dilute benzene in air. The complete conversion of benzene could be achieved at reaction temperature as low as 220 °C. The mechanism of benzene oxidation over the Cu_0.1Ce_0.5Zr_0.4O_2−δ catalyst was investigated by conducting pulse reaction of pure benzene in the absence of O₂ over the catalyst and the results indicated the involvement of lattice oxygen from the catalyst in benzene oxidation.     

La(1−x)SrxCo1−yFeyO3 perovskites prepared by sol–gel method: Characterization and relationships with catalytic properties for total oxidation of toluene

La_(1−x)Sr_xCo_(1−y)Fe_yO₃ samples have been prepared by sol–gel method using EDTA and citric acid as complexing agents. For the first time, Raman mappings were achieved on this type of samples especially to look for traces of Co₃O₄ that can be present as additional phase and not detect by XRD. The prepared samples were pure perovskites with good structural homogeneity. All these perovskites were very active for total oxidation of toluene above 200 °C. The ageing procedure used indicated good thermal stability of the samples. A strong improvement of catalytic properties was obtained substituting 30% of La³⁺ by Sr²⁺ cations and a slight additional improvement was observed substituting 20% of cobalt by iron. Hence, the optimized composition was La_0.7Sr_0.3Co_0.8Fe_0.2O₃. The samples were also characterized by BET measurements, SEM and XRD techniques. Iron oxidation states were determined by Mössbauer spectroscopy. Cobalt oxidation states and the amount of O⁻ electrophilic species were analyzed from XPS achieved after treatment without re-exposition to ambient air. Textural characterization revealed a strong increase in the specific surface area and a complete change of the shape of primary particles substituting La³⁺ by Sr²⁺. The strong lowering of the temperature at conversion 20% for the La_0.7Sr_0.3Co_(1−y)Fe_yO₃ samples can be explained by these changes. X photoelectron spectra obtained with our procedure evidenced very high amount of O⁻ electrophilic species for the La_0.7Sr_0.3Co_(1−y)Fe_yO₃ samples. These species able to activate hydrocarbons could be the active sites. The partial substitution of cobalt by iron has only a limited effect on the textural properties and the amount of O⁻ species. However, Raman spectroscopy revealed a strong dynamic structural distortion by Jahn–Teller effect and Mössbauer spectroscopy evidenced the presence of Fe⁴⁺ cations in the iron containing samples. These structural modifications could improve the reactivity of the active sites explaining the better specific activity rate of the La_0.7Sr_0.3Co_0.8Fe_0.2O₃ sample. Finally, an additional improvement of catalytic properties was obtained by the addition of 5% of cobalt cations in the solution of preparation. As evidenced by Raman mappings and TEM images, this method of preparation allowed to well-dispersed small Co₃O₄ particles that are very efficient for total oxidation of toluene with good thermal stability contrary to bulk Co₃O₄.     

Preparation of Ni/MgxTi1 − xO catalysts and investigation on their stability in tri-reforming of methane

Ni/Mg_xTi_1 − xO catalysts were prepared through a wet impregnation method by dispersing Ni on Mg_xTi_1 − xO composite oxides obtained via a sol–gel technique. The Ni/Mg_xTi_1 − xO catalysts were characterized by various means including ICP–OES, BET, XRD, H₂–TPR, SEM, and TG. No free NiO peak was found in all XRD patterns of the Ni/Mg_xTi_1 − xO catalysts. The H₂–TPR and chemisorption results indicated that adding Ti to the NiO–MgO system obstructed the formation of solid solution, and thus increased the reducibility of the catalysts. The prepared Mg_xTi_1 − xO composite oxides had the same ability to disperse Ni as TiO₂ and MgO. The tri-reforming (simultaneous oxygen reforming, carbon dioxide reforming, and steam reforming) of methane over Ni/Mg_xTi_1 − xO catalysts was carried out in a fixed bed flow reactor. The conversions of CH₄ and CO₂ can respectively be achieved as high as above 95% and 83% over Ni/Mg_0.75Ti_0.25O catalyst under the reaction conditions. The activity of Ni/Mg_0.75Ti_0.25O and Ni/Mg_0.5Ti_0.5O did not decrease for a reaction period of 50 h, indicating their rather high stability. The experimental results showed that the nature of support, the interaction between metal and support, and the ability to be reduced played an important role in improving the stability of catalysts.     

Study of IrxRu1−xO2 oxides as anodic electrocatalysts for solid polymer electrolyte water electrolysis

Electrocatalysts of the general formula Ir_xRu_1−xO₂ were prepared using Adams’ fusion method. The crystallite characterization was examined via XRD, and the electrochemical properties were examined via cyclic voltammetry (CV) in, linear sweep voltammetry (LSV) and chronopotentiometry measurements in 0.5 M H₂SO₄. The electrocatalysts were applied to a membrane electrode assembly (MEA) and studied in situ in an electrolysis cell through electrochemical impedance spectroscopy (EIS) and stationary current density–potential relations were investigated. The Ir_xRu_1−xO₂ (x = 0.2, 0.4, 0.6) compounds were found to be more active than pure IrO₂ and more stable than pure RuO₂. The most active electrocatalyst obtained had a composition of Ir_0.2Ru_0.8O₂. With an Ir_0.2Ru_0.8O₂ anode, a 28.4% Pt/C cathode and the total noble metal loading of 1.7 mg cm⁻², the potential of water electrolysis was 1.622 V at 1 A cm⁻² and 80 °C.     

Self-assembly of BixTi1−xO2 visible photocatalyst with core–shell structure and enhanced activity

Mesoporous Bi_xTi_1−xO₂ spheres with core–shell chamber were prepared by alcoholysis under solvothermal conditions. The cross-condensation between Ti–OH and Bi–OH ensured complete incorporation of Bi-dopants into TiO₂ lattice, though Bi atom is much bigger than Ti. Meanwhile, the aggregation of titania building clusters into spheres and their subsequent reactions including dissolution and re-deposition processes lead to the hollow spheres with tunable interior structure. The Bi-doping induced strong spectral response in visible region owing to the formation of narrow intermediate energy band gaps. Meanwhile, multiple reflections within the sphere interior voids promoted the light absorbance. As a result, the as-prepared Bi_xTi_1−xO₂ spheres exhibited much higher activity than the undoped TiO₂, the Bi₂O₃/TiO₂ obtained by impregnating the TiO₂ with Bi(NO₃)₃ solution, and the Bi_xTi_1−xO₂ after being ground during photodegradation of p-chlorophenol under visible light irradiation. Meanwhile, the Bi_xTi_1−xO₂ could be used repetitively for 10 times owing to the high hydrothermal stability and the absence of Bi-leaching.     

Highly active TiO2−x−yNxFy visible photocatalyst prepared under supercritical conditions in NH4F/EtOH fluid

A novel N and F co-doped TiO₂ (TiO_2−x−yN_xF_y) photocatalyst is prepared by treating the TiO₂ precursor in NH₄F/ethanol fluid under supercritical conditions. During photocatalytic degradation of methylene blue under visible light irradiation, the as-prepared TiO_2−x−yN_xF_y exhibits higher activity than the undoped TiO₂, N-doped TiO₂ (TiO_2−xN_x), and F-doped TiO₂ (TiO_2−yF_y). Based on the characterizations including XRD, Raman, FTIR, TEM, PLS, UV–vis DRS, N₂ adsorption–desorption isotherms, XPS and NH₃-TPD, the synergetic promotions of N- and F-dopants incorporated into the TiO₂ lattice are discussed based on the enhanced spectral response in visible region, oxygen vacancies, and surface acidic sites. Meanwhile, the supercritical treatment also promotes the activity owing to the increase in both the surface area and the crystallization degree of anatase, and the enhanced incorporation of N- and F-dopants into the TiO₂ lattice.     

High-performance Li4Ti5−xVxO12 (0 ≤ x ≤ 0.3) as an anode material for secondary lithium-ion battery

Powders of spinel Li₄Ti_5−xV_xO₁₂ (0 ≤ x ≤ 0.3) were successfully synthesized by solid-state method. The structure and properties of Li₄Ti_5−xV_xO₁₂ (0 ≤ x ≤ 0.3) were examined by X-ray diffraction (XRD), Raman spectroscopy (RS), scanning electronic microscope (SEM), galvanostatic charge–discharge test and cyclic voltammetry (CV). XRD shows that the V⁵⁺ can partially replace Ti⁴⁺ and Li⁺ in the spinel and the doping V⁵⁺ ion does almost not affect the lattice parameter of Li₄Ti₅O₁₂. Raman spectra indicate that the Raman bands corresponding to the Li–O and Ti–O vibrations have a blue shift due to the doping vanadium ions, respectively. SEM exhibits that Li₄Ti_5−xV_xO₁₂ (0.05 ≤ x ≤ 0.25) samples have a relative uniform morphology with narrow size distribution. Charge–discharge test reveals that Li₄Ti_4.95V_0.05O₁₂ has the highest initial discharge capacity and cycling performance among all samples cycled between 1.0 and 2.0 V; Li₄Ti_4.9V_0.1O₁₂ has the highest initial discharge capacity and cycling performance among all samples cycled between 0.0 and 2.0 V or between 0.5 and 2.0 V. This excellent cycling capability is mainly due to the doping vanadium. CV reveals that electrolyte starts to decompose irreversibly below 1.0 V, and SEI film of Li₄Ti₅O₁₂ was formed at 0.7 V in the first discharge process; the Li₄Ti_4.9V_0.1O₁₂ sample has a good reversibility and its structure is very advantageous for the transportation of lithium-ions.     

Surface properties and catalytic performance of La1−xSrxCrO3 perovskite-type oxides for CO and C3H6 combustion

Catalytic CO oxidation and C₃H₆ combustion have been studied over La_1−xSr_xCrO₃ (x = 0.0–0.3) oxides prepared by solid-state reaction and characterised by X-ray diffraction (XRD), nitrogen adsorption (BET analysis) and X-ray photoelectron spectroscopy (XPS). The expected orthorhombic perovskite structure of the chromite is observed for all levels of substitution. However, surface segregation of strontium along with a chromium oxidation process, leading to formation of Cr⁶⁺-containing phases, is produced upon increasing x and shown to be detrimental to the catalytic activity. Maximum activity is achieved for the catalyst with x = 0.1 in which mixed oxide formation upon substitution of lanthanum by strontium in the chromite becomes maximised.     

Decolorization of methylene blue by heterogeneous Fenton reaction using Fe3−xTixO4 (0 ≤ x ≤ 0.78) at neutral pH values

In this work, a series of Fe_3−xTi_xO₄ (0 ≤ x ≤ 0.78) was synthesized using a new soft chemical method. The synthetic Fe_3−xTi_xO₄ were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Mössbauer spectroscopy, thermogravimetric and differential scanning calorimetry (TG–DSC) analyses. The results showed that they were spinel structures and Ti was introduced into their structures.Then, decolorization of methylene blue (MB) by Fe_3−xTi_xO₄ in the presence of H₂O₂ at neutral pH values was studied using UV–vis spectra, dissolved organic carbon (DOC) and element C analyses. Furthermore, the degradation products remained in reaction solution after the decolorization were identified using ionic chromatography (IC), ¹³C nuclear magnetic resonance spectra (NMR), liquid chromatography and mass spectrometry (LC–MS). Although small amounts of MB were mineralized, the aromatic rings in MB were destroyed completely after the decolorization. Decolorization of MB by Fe_3−xTi_xO₄ in the presence of H₂O₂ was promoted remarkably with the increase of Ti content in Fe_3−xTi_xO₄ due to the enhancement of both adsorption and degradation of MB on Fe_3−xTi_xO₄.     

Adsorption of NO and NO2 on ceria–zirconia of composition Ce0.69Zr0.31O2: A DRIFTS study

In this study, the nature of surface intermediates generated by adsorption of NO and NO₂ on a commercial ceria–zirconia powder of composition Ce_0.69Zr_0.31O₂ was investigated using Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS). The conditions of occurrence of the main adsorbed species, i.e. nitrites and nitrates, are studied semi-quantitatively as a function of catalyst pre-treatment and/or type of adsorbed NO_x molecule. On the partially reduced ceria–zirconia, the primary role of NO_x is to re-oxidize the surface via adsorption/decomposition on reduced sites. By contrast, the formation of nitrites and nitrates readily occurs on oxidized surfaces, the latter kind of species being strongly promoted in the case of NO₂ adsorption only.     

High temperature SrCe0.9Eu0.1O3−δ proton conducting membrane reactor for H2 production using the water–gas shift reaction

The water–gas shift (WGS) reaction is used to shift the CO/H₂ ratio prior to Fischer–Tropsch synthesis and/or to increase H₂ yield. A WGS membrane reactor was developed using a mixed protonic–electronic conducting SrCe_0.9Eu_0.1O_3−δ membrane coated on a Ni–SrCeO_3−δ support. The membrane reactor overcomes the thermodynamic equilibrium limitations. A 46% increase in CO conversion and total H₂ yield was achieved at 900 °C under 3% CO and 6% H₂O, resulting in a 92% single pass H₂ production yield and 32% single pass yield of pure permeated H₂.     

Effects of preparation methods on the oxygen nonstoichiometry, B-site cation valences and catalytic efficiency of perovskite La0.6Sr0.4Co0.2Fe0.8O3−δ

La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF) powders were synthesized respectively by an EDTA (ethylenediaminetetraacetic acid)–Citrate sol–gel process and a low-temperature auto-combustion process. The samples were characterized by XRD, SEM, BET, TGA and instant temperature analysis. The iodometric titration was used to determine the average valence of Co and Fe ions and the oxygen nonstoichiometry of the prepare powders. The catalytic properties of the synthesized powders were investigated by the hydrogen peroxide catalytic decomposition. Pure-perovskite structure was formed by both synthesis methods. The oxygen nonstoichiometry of the samples prepared by the auto-combustion process is larger than that by the sol–gel process. The catalytic activities of the powders from two synthesis processes also differed largely due to the different oxygen nonstoichiometry, surface area and crystalline sizes.     

Sorption–Desorption of NOx from a Lean Gas Mixture on H3PW12O40·6H2O Supported on Carbon Nanotubes

NO _x sorption capacities and efficiencies were measured on a new type of sorbent formed by 12-tungstophosphoric acid (HPW) supported on carbon nanotubes. On such a system, the sorption of both NO and NO₂ was observed but compared with HPW alone, a complementary sorption of NO _x is possible leading to a capacity of 25 mg/g_HPW at 300 °C with an efficiency of 50%. The sorption results from the formation of a [H⁺(NO₂ ^–,NO⁺)] complex on HPW and an additional mode of adsorption by a free-nitrate which was identified by the bands at 2261, 1384 and 1295 cm^–1 using infrared spectroscopy.     

The effect of co-doping with MgO and Yb2O3 on the structure and electrical conductivity of the Sm2Zr2O7 pyrochlore

SmYb_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.15) ceramics are pressureless-sintered at 1973 K for 10 h in air. The structure and electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics are investigated by the X-ray diffraction, scanning electron microscopy and impedance spectroscopy measurements. SmYb_1−xMg_xZr₂O_7−x/2 ceramics exhibit a defect fluorite-type structure. The measured electrical conductivities of SmYb_1−xMg_xZr₂O_7−x/2 ceramics obey the Arrhenius relation, and electrical conductivity of each composition increases with increasing temperature from 673 to 1173 K. At identical temperature levels, the electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics gradually increases with increasing magnesia content. SmYb_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The electrical conductivity obtained in SmYb_1−xMg_xZr₂O_7−x/2 ceramics reaches the highest value of 2.72 × 10⁻³ S cm⁻¹ at 1173 K for the SmYb_0.85Mg_0.15Zr₂O_6.925 ceramic.     

Low-temperature catalytic combustion of chlorobenzene over MnOx–CeO2 mixed oxide catalysts

MnO_x–CeO₂ mixed oxide catalysts prepared by sol–gel method were tested for the catalytic combustion of chlorobenzene (CB), as a model of chlorinated aromatic volatile organic compounds (CVOCs). MnO_x–CeO₂ catalysts with the different ratio of Mn/Ce + Mn were found to possess high catalytic activity for catalytic combustion of CB, and MnO_x(0.86)–CeO₂ was the most active catalyst, on which the complete combustion temperature (T_90%) of chlorobenzene was 236 °C. The stability of MnO_x–CeO₂ catalysts in the CB combustion was investigated. MnO_x–CeO₂ catalysts with high Mn/Ce + Mn ratios present high stable activity, which is related to their high ability to remove Cl species adsorbed and a large amount of active surface oxygen.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.