倾斜方腔内纳米流体自然对流的数值研究

对充满Cu-水纳米流体的二维倾斜方腔内的自然对流换热进行了数值研究,研究了纳米颗粒体积份额φ、Ra数和腔体倾角对自然对流换热特性的影响。数值模拟结果表明:在纯水中加入纳米颗粒可以显著提高基液的自然对流换热特性;在一定的腔体倾角φ下,增大Ra均可以强化腔体内的自然对流换热,而且随Ra数的增大,强化效果越强;当Ra=104时,对不同的腔体倾角,纳米流体对换热强度提高的比例大致相当。     

封闭三角形通道内热管的自然对流换热研究

论述和分析了封闭腔内自然对流换热的研究进展,运用Fluent软件对封闭三角形通道内的热管与壁面的二维散热问题进行了数值模拟,模拟了封闭腔内空气自然对流换热的温度场和速度场。     

涡量-流函数法模拟不同高宽比和角度的腔内自然对流

采用涡量-流函数方程,对FLUENT软件进行二次开发,对重力作用下封闭空腔内的二维自然对流换热流场、温度场进行了数值模拟.对非正方形的矩形空腔内的自然对流换热进行了数值计算,结果表明不同的高宽比例对自然对流换热有很大的影响;该文还对Ra=104时放置不同角度的封闭腔进行了数值计算,揭示了重力作用下不同角度时的自然对流换热变化,发现在某一倾斜角度时(θ=45°左右),平均换热系数Numean存在极大值.     

封闭腔内MWCNT纳米流体自然对流传热的数值模拟

采用Fluent软件对封闭腔内纳米流体层流自然对流换热进行了数值模拟研究.重点分析了Ra数和纳米颗粒的体积分数对自然对流换热特性的影响.数值模拟结果表明:在机油中添加多壁碳纳米管(MWCNT)粒子并没有提高基液的自然对流传热特性;对于给定的Ra数下,随着纳米颗粒体积分数的增大,纳米流体的传热特性也随之减弱;对于给定的体积分数,随着Ra数的增大,纳米流体的传热特性显著增强,但纳米流体的传热性能比机油的要弱,且在同一体积分数下随着Ra数的增大,传热性能减弱的程度要减小.     

壁温周期振荡条件下方腔内纳米流体自然对流换热研究

对充满Cu-水纳米流体方腔内的非稳态自然对流换热进行了数值研究。综合研究了不同振荡波形下,纳米颗粒的体积份额和振荡波幅A对自然对流换热的影响。结果表明:在水中添加Cu纳米颗粒可以强化水的自然对流换热;体积份额和振荡波幅A的增大都加强纳米流体自然对流换热,但是不同振荡波形,加强程度不同并提出振荡面积S的概念,即振荡波形与其平均值围成的面积,曲线拟合显示时均努塞尔特数Nu随S增大呈指数曲线上升。     

两种CPU散热器换热特性的数值研究

对整体平直翅片与分段开缝平直翅片两种不同结构的CPU散热器，在不同加热功率和不同风速下的散热特性进行了数值模拟。采用商业软件FLUENT6．0进行计算，结果显示：对流换热表面传热系数和热阻主要与风速有关，与加热功率关系不大，对流换热表面传热系数的计算结果和实验数据趋势一致。在低风速下，加热功率对这两种散热器压降的影响也不大。采取数值模拟的方法对CPU散热器进行研究是实验方法的可靠补充，计算所得的结果有助于分析CPU散热器的换热过程，并可为电子设备的设计和改进提供参考。     

封闭腔内纳米流体自然对流换热的数值模拟

采用数值模拟方式研究充满了纳米流体的封闭腔内的稳态自然对流。重点分析了纳米颗粒的体积分数,Ra数以及不同类型纳米颗粒对自然对流换热特性的影响。数值模拟结果表明:在纯水中加入纳米颗粒可以显著提高基液的自然对流换热特性;对于给定的Ra数下,随着纳米流体的体积分数增大,纳米流体换热效果显著增强;对于给定的体积分数下,随着Ra数增大,纳米流体的换热强度也随之增大,并且换热机理由热传导为主变为热对流为主;通过Ag,Cu,CuO和Al2O3四种纳米颗粒的对流换热效果比较分析得出,金属Ag和Cu纳米颗粒比金属氧化物CuO和Al2O3的纳米颗粒制备的纳米流体的对流换热效果更好。     

周期性边界变化条件下封闭腔内纳米流体的流动模拟

文献采用数值模拟方式研究充满了纳米流体封闭腔内的瞬态自然对流。热边界条件为温度周期性变化的正弦函数。重点分析了在同一Ra下,正弦函数的振幅和频率(或周期)对纳米流体强化对流换热的影响;结果显示:随着热边界的正弦函数的振幅和频率变大,热边界的瞬态Nu数和平均Nu数也越大;同时还观察封闭腔内的漩涡中心,随时间变化周期性发生转移;这些结果对后期研究纳米流体的瞬态自然对流有很大的帮助。     

一种笔记本电脑水冷散热装置研究

针对笔记本电脑散热问题设计了一种新型外置无强迫对流散热器,通过设置折流板和导流槽增大换热面积,采用实验和数值方法对散热器的结构参数及散热性能进行了研究。结果表明,研制的散热器具有较好的散热性能,可以满足CPU及GPU的散热要求。     

圆环腔内纳米流体自然对流的数值研究

采用Fluent软件对圆环封闭腔内的Ag-水纳米流体自然对流传热进行数值模拟,着重分析在不同瑞利数下Ag纳米颗粒的添加量和圆环内外壁半径比对圆环传热性能的影响.研究结果表明,随着瑞利数的增加,圆环间的换热强度不断加剧,换热由热传导逐渐向对流转变.添加纳米颗粒降低了换热性能,且随着颗粒浓度的增加换热效果不断恶化;同时,圆环半径比对换热有很大的影响,对一定的瑞利数而言随着半径比的减小,换热性能逐渐增强,且增大的趋势越来越显著.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...