Synthesis and characterization of new rigid‐rod and organosoluble poly(amide–imide)s based on 1,4‐bis(trimellitimido)‐2,3,5,6‐tetramethylbenzene

A series of new aromatic poly(amide–imide)s (PAIs) was synthesized by triphenyl phosphite‐activated polycondensation of the diimide–diacid, 1,4‐bis(trimellitimido)‐2,3,5,6‐tetramethylbenzene (I), with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP), pyridine, and calcium chloride. The PAIs had inherent viscosities of 0.82–2.43 dL/g. The diimide–diacid monomer (I) was prepared from 2,3,5,6‐tetramethyl‐p‐phenylenediamine with trimellitic anhydride (TMA). Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents including NMP, N,N‐dimethylacetamide (DMAc), and N,N‐dimethylformamide (DMF). Transparent, flexible, and tough films of these polymers could be cast from DMAc solutions. Their cast films had tensile strengths ranging from 80 to 95 MPa, elongation at break from 10 to 45%, and initial modulus from 2.01 to 2.50 GPa. The 10% weight loss temperatures of these polymers were above 510°C in nitrogen. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1162–1170, 2000     

Synthesis and properties of poly(amide–imide)s based on N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide,p‐aminobenzoic acid and various aromatic diamines

A new diimide–diacid monomer, N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide (I), was prepared by azeotropic condensation of 4,4′‐oxydiphthalic anhydride (ODPA) and p‐aminobenzoic acid (p‐ABA) at a 1:2 molar ratio in a polar solvent mixed with toluene. A series of poly(amide–imide)s (PAI, III_a–m) was synthesized from the diimide–diacid I (or I′, diacid chloride of I) and various aromatic diamines by direct polycondensation (or low temperature polycondensation) using triphenyl phosphite and pyridine as condensing agents. It was found that only III_k–m having a meta‐structure at two terminals of the diamine could afford good quality, creasable films by solution‐casting; other PAIs III using diamine with para‐linkage at terminals were insoluble and crystalline; though III_g–i contained the soluble group of the diamine moieties, their solvent‐cast films were brittle. In order to improve their to solubility and film quality, copoly(amide–imide)s (Co‐PAIs) based on I and mixtures of p‐ABA and aromatic diamines were synthesized. When on equimolar of p‐ABA (m = 1) was mixed, most of Co‐PAIs IV had improved solubility and high inherent viscosities in the range 0.9–1.5 dl g^?1; however, their films were still brittle. With m = 3, series V was obtained, and all members exhibited high toughness. The solubility, film‐forming ability, crystallinity, and thermal properties of the resultant poly(amide–imide)s were investigated. © 2002 Society of Chemical Industry     

Synthesis and properties of fluorinated aromatic poly(amide imide)s based on 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone and various bis(trimellitimide)s

A CF₃‐containing diamine, 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone ( 2 ), was synthesized from 4,4′‐dihydroxybenzophenone and 2‐chloro‐5‐nitrobenzotrifluoride. Imide‐containing diacids ( 3 and 5B_a – 5B_g ) were prepared by the condensation reaction of aromatic diamines and trimellitic anhydride. Then, two series of novel soluble aromatic poly(amide imide)s (PAIs; 6A_a – 6A_k and 6B_a – 6B_g ) were synthesized from a diamine ( 4A_a – 4A_k or 2 ) with the imide‐containing diacids ( 3 and 5B_a – 5B_g ) via direct polycondensation with triphenyl phosphate and pyridine. The aromatic PAIs had inherent viscosities of 0.74–1.76 dL/g. All of the synthesized polymers showed excellent solubility in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide (DMAc), and afforded transparent and tough films by DMAc solvent casting. These polymer films had tensile strengths of 90–113 MPa, elongations at break of 8–15%, and initial moduli of 2.0–2.9 GPa. The glass‐transition temperatures of the aromatic PAIs were in the range 242–279°C. They had 10% weight losses at temperatures above 500°C and showed excellent thermal stabilities. The 6B series exhibited less coloring and showed lower yellowness index values than the corresponding 6A series. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3641–3653, 2006     

Synthesis and properties of new photosensitive and chiral poly(amide‐imide)s based on bicyclo[2,2,2]oct‐7‐ene‐2,3,5,6‐tetracarboxylic diimide and dibenzalacetone moieties in the main chain

Aromatic poly(amide‐imide)s (PAIs) are high‐performance materials with a good compromise between thermal stability and processability when compared with polyamides or polyimides of analogous structures. In addition, the incorporation of photosensitive functional groups and chiral segments into the polymer backbone can lead to interesting polymers for various applications. In this work, six new photosensitive and chiral PAIs were synthesized from the direct polycondensation reaction of novel N,N′‐(bicyclo[2,2,2]oct‐7‐ene‐tetracarboxylic)‐bis‐L ‐amino acids with 2,5‐bis(4‐aminobenzylidene)cyclopentanone as dibenzalacetone moiety using two different methods. The polymerization reactions produced a series of photosensitive and optically active PAIs in high yields and with good inherent viscosities. The resulting polymers were characterized using Fourier transform infrared and ¹H NMR spectroscopy, elemental analysis, inherent viscosity, specific rotation, solubility tests and UV‐visible spectroscopy. The thermal properties of the PAIs were investigated using thermogravimetric analysis. Due to the presence of the dibenzalacetone moiety in the polymer chain, the PAIs have photosensitive properties. Also, these PAIs are optically active and soluble in various organic solvents. These resulting new polymers have the potential to be used in column chromatography for the separation of enantiomeric mixtures. Copyright © 2009 Society of Chemical Industry     

Novel optically active poly(amide‐imide)s with tetrahydropyrimidinone and tetrahydro‐2‐thioxopyrimidine moieties by microwave‐assisted polycondensation

Rapid and highly efficient synthesis of novel poly(amide‐imide)s (PAIs) were achieved under microwave irradiation by using a domestic microwave oven from the polycondensation reactions of 4,4′‐carbonyl‐bis(phthaloyl‐L ‐alanine) diacid chloride [N,N′‐(4,4′‐carbonyldiphthaloyl)] bisalanine diacid chloride (1) with six different derivatives of tetrahydropyrimidinone and tetrahydro‐2‐thioxopyrimidine compounds (2a–2f) in the presence of a small amount of a nonpolar organic medium that acts as a primary microwave absorber. Suitable organic media was o‐cresol. The polycondensation proceeded rapidly and was almost completed within 10 min, giving a series of PAIs with inherent viscosities of about 0.25–0.45 dL/g. The resulting PAIs were obtained in high yield and are optically active and thermally stable. All of the above compounds were fully characterized by means of Fourier transform infrared spectroscopy, elemental analyses, inherent viscosity (η_inh), solubility test, and specific rotation. Thermal properties of the PAIs were investigated using thermogravimetric analysis. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2416–2421, 2001     

Synthesis and characterization of soluble poly(amide‐imide)s bearing triethylamine sulfonate groups as gas dehumidification membrane material

A series of soluble poly(amide‐imide)s (PAIs) bearing triethylammonium sulfonate groups were synthesized directly using trimellitic anhydride chloride (TMAC) polycondensation with sulfonated diamine such as 2,2′‐benzidinedisulfonic acid (BDSA), 4,4′‐diaminodiphenyl ether‐2,2′‐disulfonic acid (ODADS), and nonsulfonated diamine 4,4‐diaminodiphenyl methane in the presence of triethylamine. The resulting copolymers exhibited high molecular weights (high inherent viscosity), and a combination of desirable properties such as good solubility in dipolar aprotic solvents, film‐forming capability, and good mechanical properties. Wide‐angle X‐ray diffraction revealed that the polymers were amorphous. These copolymers showed high permeability coefficients of water vapor because of the presence of the hydrophilic triethylammonium sulfonate groups. The water vapor permeability coefficients (P_w) and permselectivity coefficients of water vapor to nitrogen and methane [α(H₂O/N₂) and α(H₂O/CH₄)] of the films increased with increasing the amount of the triethylammonium sulfonated groups. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of novel heat resistance poly(amide‐imide)s from N,N′‐[2,5‐bis(4‐aminobenzylidene) cyclopentanone] bistrimellitimide acid and various aromatic diamines

A new‐type of dicarboxylic acid was synthesized from the reaction of 2,5‐bis(4‐aminobenzylidene)cyclopentanone with trimellitic anhydride in a solution of glacial acetic acid/pyridine (Py) at refluxing temperature. Six novel heat resistance poly(amide‐imide)s (PAIs) with good inherent viscosities were synthesized, from the direct polycondensation reaction of N,N′‐[2,5‐bis(4‐aminobenzylidene)cyclopentanone]bistrimellitimide acid with several aromatic diamines, by two different methods such as direct polycondensation in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP)/triphenyl phosphite (TPP)/calcium chloride (CaCl₂)/pyridine (Py) and direct polycondensation in a p‐toluene sulfonyl chloride (tosyl chloride, TsCl)/pyridine (Py)/N,N‐dimethylformamide (DMF) system. All of the above polymers were fully characterized by ¹H NMR, FTIR, elemental analysis, inherent viscosity, solubility tests, UV‐vis spectroscopy, differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), and derivative of thermaogravimetric (DTG). The resulted poly(amide‐imide)s (PAIs) have showed admirable good inherent viscosities, thermal stability, and solubility. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of polyimides based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane

A series of polyimide (PI) thin films were synthesized based on bis[3,5‐dimethyl‐4‐(4‐aminophenoxy)phenyl]methane and conventional aromatic dianhydrides. The structures and properties of the thin films were measured with Fourier transform infrared, NMR, thermogravimetric analysis, dynamic mechanical analysis, and impedance analysis. The PI films exhibited glass‐transition temperatures in the range of 211–300°C and possessed initial thermal decomposition temperature reaching up to 457–482°C in air and 461–473°C in nitrogen. Some PI films had high solubility in organic solvents such as 1‐methyl‐2‐pyrrolidinone, N,N‐dimethylformamide, N,N‐dimethylacetamide, dimethyl sulfoxide, m‐cresol, tetrahydrofuran, and CHCl₃. The mechanical properties of these films were also examined. The dielectric constants of the films were in the range of 2.8–3.3 at 25°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1265–1270, 2007     

Synthesis and characterization of novel thermally stable and optically active poly(amide‐imide)s derived from N,N′‐(4,4′‐diphthaloyl)‐bis‐L‐leucine diacid and aromatic diamines

A new diacid containing optically active functional groups, N,N′‐(4,4′‐diphthaloyl)‐bis‐L ‐leucine diacid ( 3 ), was synthesized and used in a preparation of a series of poly(amide‐imide)s (PAIs) by direct polycondensation with various aromatic diamines in N‐methyl‐2‐pyrrolidinone (NMP). All polymers derived from diacid ( 3 ) were highly organosoluble in the solvents like N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethyl sulfoxide, tetrahydrofuran, γ‐butyrolactone, cyclohexanone, and chloroform at room temperature or upon heating. Inherent viscosities of the PAIs were found to range between 0.34 and 0.61·dL g^?1. All the PAIs afforded flexible and tough films. The glass‐transition temperatures of these PAIs were recorded between 212 and 237°C by differential scanning calorimetry, and the 10% weight loss temperatures were ranging from 372 to 393°C and 336–372°C under nitrogen and air, respectively. The polyimide films had a tensile strength in the range of 63–88 MPa and a tensile modulus in the range of 1.2–1.7 GPa. Optically active PAIs exhibited specific rotations in the range of ?10.58° to ?38.70°. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of novel benzhydrol-containing poly(amide-imide)s

A series of novel benzhydrol-containing poly(amide-imide)s (PAIs) have been prepared from a new diimide-dicarboxylic acid, N,N′-bis(4-hydroxycarbonyl)-benzhydrol-3,3′,4,4′-tetracarboxydiimide (BHTDA-DIA), with various diamines by direct polycondensation using triphenyl phosphite and pyridine as condensing agents. The polymers obtained had inherent viscosities of 0.35–0.96 dl g⁻¹. All these PAIs, except polymer PAI-2, were soluble in N-methyl-2-pyrrolidinone and N,N-dimethylacetamide containing LiCl (1 wt%). Tough and flexible PAI films could be obtained by casting PAIs from their DMAc or NMP solutions, except for polymer PAI-2. The polymer films had a tensile strength of 93–111 MPa, an elongation at break range of 4–6%, and an initial modulus range of 2.7–3.8 GPa. The glass transition temperatures of most polymers were found to be above 255 °C. These polymers were fairly stable up to a temperature around or above 400 °C, and lost 10% weight in the range 426–507 °C in nitrogen and 423–515 °C in air. © 1999 Society of Chemical Industry     

Syntheses and properties of new poly(amide–imide)s based on 1,4‐bis(4‐aminophenoxy)naphthalene and various diimide–diacids

A series of new alternative poly(amide–imide)s (PAIs, III_a–j ) was synthesized by the direct polycondensation of 1,4‐bis(4‐aminophenoxy)naphthalene (1,4‐BAPON) with various aromatic diimide–diacids. These polymers were obtained in quantitative yields with inherent viscosities of 0.71–1.03 dL/g. Except for III_a, most of the polymers were soluble in aprotic polar solvents such as NMP, DMAc, DMF, and DMSO and could be solution‐cast into transparent, flexible, and tough films. The glass transition temperatures of these PAIs were in the range of 235–280°C. Thermogravimetric analyses established that these polymers were fairly stable up to 450°C, and 10% weight loss temperatures were recorded in the range of 520–569°C under nitrogen and 506–566°C under an air atmosphere. Compared with the PAIs with the 1,4‐bis(4‐aminophenoxy)benzene structure (series IV), the solubility of series III was better than that of series IV. Series III also exhibited lower crystallinity and better processability than those of series IV. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 217–225, 2000     

Synthesis and properties of polyamides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan

A new diamine 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan ( 3 ) was prepared through the nucleophilic displacement of 5,5′‐bis(4‐hydroxylphenyl)‐hexahydro‐4,7‐methanoindan ( 1 ) with p‐halonitrobenzene in the presence of K₂CO₃ in N,N‐dimethylformamide (DMF), followed by catalytic reduction with hydrazine and Pd/C in ethanol. A series of new polyamides were synthesized by the direct polycondensation of diamine 3 with various aromatic dicarboxylic acids. The polymers were obtained in quantitative yields with inherent viscosities of 0.76–1.02 dl g⁻¹. All the polymers were soluble in aprotic dipolar solvents such as N,N‐dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidone (NMP), and could be solution cast into transparent, flexible and tough films. The glass transition temperatures of the polyamides were in the range 245–282 °C; their 10% weight loss temperatures were above 468 °C in nitrogen and above 465 °C in air. © 2000 Society of Chemical Industry     

Synthesis and characterization of aromatic polyamides containing an s‐triazine ring with thiophenoxy linkages

A series of aromatic polyamides containing an s‐triazine ring with thiophenoxy linkages was synthesized from two new diacids, namely 2,4‐bis‐(4‐carboxyphenoxy)‐6‐thiophenoxy‐s‐triazine and 2,4‐bis‐(3‐carboxyphenoxy)‐6‐thiophenoxy‐s‐triazine, and commercially available aromatic diamines by using Yamazaki's phosphorylation reaction. The polyamides were obtained in good yields and were characterized by solubility tests, viscosity measurements, FTIR, ¹H and ¹³C NMR spectroscopy, X‐ray diffraction studies and thermogravimetric analysis. The polyamides were found to have inherent viscosities in the range of 0.35 to 0.56 dl g^?1 in N,N‐dimethylacetamide (DMAc) at 30 ± 0.1 °C. All the polyamides were readily soluble in solvents such as DMAc, N‐methyl‐2‐pyrrolidone (NMP), N,N‐dimethylformamide (DMF) and m‐cresol. Thermogravimetric analysis of the polyamides indicated no weight loss below 345 °C under a nitrogen atmosphere. Copyright © 2004 Society of Chemical Industry     

New poly(amide‐imide) syntheses. 24. Synthesis and properties of fluorinated poly(amide‐imide)s based on 2,2‐bis[4‐(trimellitimidophenoxy)phenyl]hexafluoropropane and various aromatic diamines

An imide ring‐performed dicarboxylic acid bearing one hexafluoroisopropylidene and two ether linkages between aromatic rings, 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane (II), was prepared from the condensation of 2,2‐bis[4‐(4‐aminophenoxy)phenyl]hexafluoropropane and trimellitic anhydride. A novel series of poly(amide‐imide)s having inherent viscosities of 0.72 ∼ 1.86 dL g⁻¹ was prepared by the triphenyl phosphite‐activated polycondensation from the diimide‐diacid (II) with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrolidone, pyridine, and calcium chloride. Several of the resulting polymers were soluble in polar amide solvents, and their solutions could be cast into transparent, thin, flexible films having good tensile properties and high thermal stability. The 10% weight loss temperatures were all above 495°C in air or nitrogen atmosphere, and the glass transition temperatures were in the range of 237°–276°C. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 823–831, 1999     

Synthesis and characterization of novel poly(amide imide)s based on bis(p‐amidobenzoic acid)‐n‐trimellitylimido‐L‐leucine

N‐Trimellitylimido‐L ‐leucine was reacted with thionyl chloride, and N‐trimellitylimido‐L ‐leucine diacid chloride was obtained in a quantitative yield. The reaction of this diacid chloride with p‐aminobenzoic acid was performed in dry tetrahydrofuran, and bis(p‐amidobenzoic acid)‐N‐trimellitylimido‐L ‐leucine (5) was obtained as a novel optically active aromatic imide–amide diacid monomer in a high yield. The direct polycondensation reaction of the monomer imide–amide diacid 5 with 4,4′‐diaminodiphenylsulfone, 4,4′‐diaminodiphenylether, 1,4‐phenylenediamine, 1,3‐phenylenediamine, 2,4‐diaminotoluene, and benzidine (4,4′‐diaminobiphenyl) was carried out in a medium consisting of triphenyl phosphite, N‐methyl‐2‐pyrolidone, pyridine, and calcium chloride. The resulting novel poly(amide imide)s (PAIs), with inherent viscosities of 0.22–0.52 dL g^?1, were obtained in high yields, were optically active, and had moderate thermal stability. All of the compounds were fully characterized with IR spectroscopy, elemental analyses, and specific rotation. Some structural characterization and physical properties of these new optically active PAIs are reported. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 35–43, 2002; DOI 10.1002/app.10181     

Synthesis and characterization of new poly(amide‐imide)s based on 1,4‐bis(trimellitimido)‐2,5‐dichlorobenzene

A series of new aromatic poly(amide‐imide)s were synthesized by the triphenyl phosphite‐activated polycondensation of the diimide‐diacid, 1,4‐bis(trimellitimido)‐2,5‐dichlorobenzene (I), with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP), pyridine, and calcium chloride. The poly(amide‐imide)s had inherent viscosities of 0.88–1.27 dL g⁻¹. The diimide‐diacid monomer (I) was prepared from 2,5‐dichloro‐p‐phenylenediamine with trimellitic anhydride. All the resulting polymers were amorphous and were readily soluble in a variety of organic solvents, including NMP and N,N‐dimethylacetamide. Transparent, flexible, and tough films of these polymers could be cast from N,N‐dimethylacetamide or NMP solutions. Cast films had tensile strengths ranging from 92 to 127 MPa, elongations at break from 4 to 24%, and initial moduli from 2.59 to 3.65 GPa. The glass transition temperatures of these polymers were in the range of 256°–317°C, and the 10% weight loss temperatures were above 430°C in nitrogen. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 271–278, 1999     

Organosoluble and light‐colored fluorinated polyimides based on 1,1‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]‐1‐phenylethane and various aromatic dianhydrides

To investigate the CF₃ group affecting the coloration and solubility of polyimides (PI), a novel fluorinated diamine 1,1‐bis[4‐(4‐amino‐2‐ trifluoromethylphenoxy)phenyl]‐1‐phenylethane (2) was prepared from 1,1‐ bis(4‐hydrophenyl)‐1‐phenylethan and 2‐chloro‐5‐nitrobenzotrifluoride. A series of light‐colored and soluble PI 5 were synthesized from 2 and various aromatic dianhydrides 3a–f using a standard two‐stage process with thermal 5a– f(H) and chemical 5a–f(C) imidization of poly(amic acid). The 5 series had inherent viscosities ranging from 0.55 to 0.98 dL/g. Most of 5a–f(H) were soluble in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone (NMP), N,N‐ dimethylacetamide (DMAc), and N,N‐dimethylformamide (DMF), and even soluble in less polar solvents, such as m‐Cresol, Py, Dioxane, THF, and CH₂Cl₂, and the 5(C) series was soluble in all solvents. The GPC data of the 5a–f(C) indicated that the Mn and Mw values were in the range of 5.5–8.7 × 10⁴ and 8.5–10.6 × 10⁴, respectively, and the polydispersity index (PDI) Mw /Mn values were 1.2–1.5. The PI 5 series had excellent mechanical properties. The glass transition temperatures of the 5 series were in the range of 232–276°C, and the 10% weight loss temperatures were at 505–548 °C in nitrogen and 508–532 °C in air, respectively. They left more than 56% char yield at 800°C in nitrogen. These films had cutoff wavelengths between 356.5–411.5 nm, the b* values ranged from 5.0–71.1, the dielectric constants, were 3.11–3.43 (1MHz) and the moisture absorptions were in the range of 011–0.40%. Comparing 5 containing the analogous PI 6 series based on 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐ phenylethane (BAPPE), the 5 series with the CF₃ group showed lower color intensity, dielectric constants, and better solubility. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2399–2412, 2005     

New poly(amide imide)s containing bis(4‐trimellitimidophenyl) sulfone and hydantoin moieties in the main chain: Synthesis and properties

Several new poly(amide imide)s were synthesized through the polycondensation reactions of bis(4‐trimellitimidophenyl) sulfone [N,N′‐(4,4′‐diphenylsulfone) bistrimellitimide] with a number of hydantoin derivatives in a medium consisting of thionyl chloride, N‐methyl‐2‐pyrrolidone, and pyridine. The polycondensations produced a series of novel poly(amide imide)s in high yields with inherent viscosities of 0.20–0.46 dL/g. The resulting poly(amide imide)s were characterized with elemental analysis, viscosity measurements, thermogravimetric analysis, derivative thermogravimetry, solubility testing, and Fourier transform infrared spectroscopy. All the polymers were soluble at room temperature in polar solvents such as N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethyl sulfoxide, tetrahydrofuran, and N‐methyl‐2‐pyrrolidone. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1776–1782, 2005     

Novel organosoluble poly(amide‐imide‐imide)s synthesized from new tetraimide‐dicarboxylic acid by condensation with 4,4′‐oxydiphthalic anhydride, 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene,trimellitic anhydride,and various aromatic diamines

A new monomer of tetraimide‐dicarboxylic acid (IV) was synthesized by starting from ring‐opening addition of 4,4′‐oxydiphthalic anhydride, trimellitic anhydride, and 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene at a 1:2:2 molar ratio in N‐methyl‐2‐pyrrolidone (NMP). From this new monomer, a series of novel organosoluble poly(amide‐imide‐imide)s with inherent viscosities of 0.7–0.96 dL/g were prepared by triphenyl phosphite activated polycondensation from the tetraimide‐diacid with various aromatic diamines. All synthesized polymers were readily soluble in a variety of organic solvents such as NMP and N,N‐dimethylacetamide, and most of them were soluble even in less polar m‐cresol and pyridine. These polymers afforded tough, transparent, and flexible films with tensile strengths ranging from 99 to 125 MPa, elongations at break from 12 to 19%, and initial moduli from 1.6 to 2.4 GPa. The thermal properties and stability were also good with glass‐transition temperatures of 236–276°C and thermogravimetric analysis 10 wt % loss temperatures of 504–559°C in nitrogen and 499–544°C in air. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2854–2864, 2006     

Synthesis and characterization of new cardo poly(ether imide)s derived from 9,9‐bis [4‐(4‐aminophenoxy)phenyl]xanthene

A series of new cardo poly(ether imide)s bearing flexible ether and bulky xanthene pendant groups was prepared from 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene with six commercially available aromatic tetracarboxylic dianhydrides in N,N‐dimethylacetamide (DMAc) via the poly(amic acid) precursors and subsequent thermal or chemical imidization. The intermediate poly(amic acid)s had inherent viscosities between 0.83 and 1.28 dL/g, could be cast from DMAc solutions and thermally converted into transparent, flexible, and tough poly(ether imide) films which were further characterized by X‐ray and mechanical analysis. All of the poly(ether imide)s were amorphous and their films exhibited tensile strengths of 89–108 MPa, elongations at break of 7–9%, and initial moduli of 2.12–2.65 GPa. Three poly(ether imide)s derived from 4,4′‐oxydiphthalic anhydride, 4,4′‐sulfonyldiphthalic anhydride, and 2,2‐bis(3,4‐dicarboxyphenyl))hexafluoropropane anhydride, respectively, exhibited excellent solubility in various solvents such as DMAc, N,N‐dimethylformamide, N‐methyl‐2‐pyrrolidinone, pyridine, and even in tetrahydrofuran at room temperature. The resulting poly(ether imide)s with glass transition temperatures between 286 and 335°C had initial decomposition temperatures above 500°C, 10% weight loss temperatures ranging from 551 to 575°C in nitrogen and 547 to 570°C in air, and char yields of 53–64% at 800°C in nitrogen. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012