Kinetics of thermal degradation of nanometer calcium carbonate/linear low‐density polyethylene nanocomposites

To improve the thermal properties of linear low‐density polyethylene (LLDPE), the CaCO₃/LLDPE nanocomposites were prepared from nanometer calcium carbonate (nano‐CaCO₃) and LLDPE by melt‐blending method. A series of testing methods such as thermogravimetry analysis (TGA), differential thermogravimetry analysis, Kim‐Park method, and Flynn‐Wall‐Ozawa method were used to characterize the thermal property of CaCO₃/LLDPE nanocomposites. The results showed that the CaCO₃/LLDPE nanocomposites have only one‐stage thermal degradation process. The initial thermal degradation temperature T₀ increasing with nano‐CaDO₃ content, and stability of LLDPE change better. The thermal degradation activation energy (E_a) is different for different nano‐CaCO₃ content. When the mass fraction of nano‐CaCO₃ in nanocomposites is up to 10 wt %, the nanocomposite has the highest thermal degradation E_a, which is higher (28 kJ/mol) than pure LLDPE. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of nano/micro‐calcium carbonate particles/polypropylene composites

A new kind of polypropylene (PP)/CaCO₃ composites was prepared on a twin screw extruder with the nanoparticle content of 5 wt % and the 2500 mesh microparticle content of 15 wt %. The mechanical property of four different samples [pure PP (1) , PP filled with 15 wt % microCaCO₃ particle composites (2) , PP filled with 5 wt % nanoCaCO₃ particle composites (3) and PP filled with micro/nano‐CaCO₃ complex size particle composites (4) ] was investigated through tensile tests, notched Izod impact tests and SEM. The results indicated that the sample 4 had the best mechanical property. The proofs of SEM showed that the high impact energy could lead to debonding and creating microcavitation between the nanoparticle and polymer interface if the polymer was filled with the nanoparticles. This process could absorb a lot of mechanical failure energy, but too much mechanical failure energy would lead to the enlargement of microcavitation and the destruction of the composites in sample 3 . In sample 4 , the microparticle could be used to prevent the enlargement of microcavitation in the matrix polymer under the higher impact failure energy. In this article, the model of the impacting failure process of micro/nanoCaCO₃/PP composites was established. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of linear low‐density polyethylene/sepiolite nanocomposites

Linear low‐density polyethylene (LLDPE)/sepiolite nanocomposites were prepared by melt blending using unmodified and silane‐modified sepiolite. Two methods were used to modify sepiolite: modification before heat mixing (ex situ) and modification during heat mixing (in situ). The X‐ray diffraction results showed that the position of the main peak of sepiolite remained unchanged during modification step. Infrared spectra showed new peaks confirming the development of new bonds in modified sepiolite and nanocomposites. SEM micrographs revealed the presence of sepiolite fibers embedded in polymer matrix. Thermogravimetric analysis showed that nanocomposites exhibited higher onset degradation temperature than LLDPE. In addition, in situ modified sepiolite nanocomposites exhibited higher thermal stability than ex situ modified sepiolite nanocomposites. The ultimate tensile strength and modulus of the nanocomposites were improved; whereas elongation at break was reduced. The higher crystallization temperature of some nanocomposite formulations revealed a heterogeneous nucleation effect of sepiolite. This can be exploited for the shortening of cycle time during processing. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of linear low‐density polyethylene/dickite nanocomposites prepared by the direct melt blending of linear low‐density polyethylene with exfoliated dickite

Dickite particles were exfoliated by the thermal decomposition of molecular urea in the interlayer of dickite. The exfoliated dickite (ED) was composed with linear low‐density polyethylene (LLDPE) to prepare a novel LLDPE/dickite nanocomposite (LDN‐5). X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to evaluate the exfoliation effect. FTIR spectra showed that the inner‐surface hydroxyls of dickite decreased because of the sufficient exfoliation of the dickite layers. The 001 diffraction of dickite in the XRD pattern almost disappeared after exfoliation; this indicated the random orientation of dickite platelets. SEM and TEM micrographs confirmed the effective thermal decomposition of the interlamellar molecular urea ED layers, which resulted in smaller particle sizes and better dispersions of dickite in the resulting LLDPE/dickite composite. The microstructure of LDN‐5 showed that most of the dickite platelets were exfoliated and homogeneously dispersed in the LLDPE; this led to increases in the anticorrosion properties and thermal stabilities of LDN‐5. The results of salt‐spray tests illustrated that the corrosion rate of the iron coupon decreased from 23% (LLDPE packing) to 0.4% (LDN‐5 packing). Moreover, the thermal degradation temperature corresponding to a mass loss of 10% increased from 330°C (pure LLDPE) to 379°C (LDN‐5). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and flame‐retarding properties of styrene–butadiene rubber filled with nano‐CaCO3 as a filler and linseed oil as an extender

A nanosize CaCO₃ filler was synthesized by an in situ deposition technique, and its size was confirmed by X‐ray diffraction. CaCO₃ was prepared in three different sizes (21, 15, and 9 nm). Styrene–butadiene rubber (SBR) was filled with 2–10 wt % nano‐CaCO₃ with 2% linseed oil as an extender. Nano‐CaCO₃–SBR rubber composites were compounded on a two‐roll mill and molded on a compression‐molding machine. Properties such as the specific gravity, swelling index, hardness, tensile strength, abrasion resistance, modulus at 300% elongation, flame retardancy, and elongation at break were measured. Because of the reduction in the nanosize of CaCO₃, drastic improvements in the mechanical properties were found. The size of 9 nm showed the highest increase in the tensile strength (3.89 MPa) in comparison with commercial CaCO₃ and the two other sizes of nano‐CaCO₃ up to an 8 wt % loading in SBR. The elongation at break also increased up to 824% for the 9‐nm size in comparison with commercial CaCO₃ and the two other sizes of nano‐CaCO₃. Also, these results were compared with nano‐CaCO₃‐filled SBR without linseed oil as an extender. The modulus at 300% elongation, hardness, specific gravity, and flame‐retarding properties increased with a reduction in the nanosize with linseed oil as an extender, which helped with the uniform dispersion of nano‐CaCO₃ in the rubber matrix. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2563–2571, 2005     

Preparation and characterization of modified‐clay‐reinforced and toughened epoxy‐resin nanocomposites

Epoxy–clay nanocomposites were prepared by the dispersion of an organically modified layered clay in an epoxy resin (diglycidyl ether of bisphenol A) and curing in the presence of methyl tetrahydro acid anhydride at 80–160°C. The nanometer‐scale dispersion of layered clay within the crosslinked epoxy‐resin matrix was confirmed by X‐ray diffraction and transmission electron microscopy, and the basal spacing of the silicate layer was greater than 100–150 Å. Experiments indicated that the hydroxyethyl groups of the alkyl ammonium ions, which were located in the galleries of organically modified clay, participated in the curing reaction and were directly linked to the epoxy‐resin matrix network. Experimental results showed that the properties of epoxy were improved, evidently because of the loading of organically modified clay. The impact strength and tensile strength of the nanocomposites increased by 87.8 and 20.9%, respectively, when 3 wt % organic clay was loaded, and this demonstrated that the composites were toughened and strengthened. The thermal‐decomposition and heat‐distortion temperatures were heightened in comparison with those of pure epoxy resin, and so were the dynamic mechanical properties, including the storage modulus and glass‐transition temperature. Moreover, experiments showed that most properties of the composites were ameliorated with low clay contents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2649–2652, 2004     

Preparation and properties of nano‐CaCO3/acrylonitrile‐butadiene‐styrene composites

CaCO₃/acrylonitrile‐butadiene‐styrene (ABS) and CaCO₃/ethylene‐vinyl acetate copolymer (EVA)/ABS nanocomposites were prepared by melting‐blend with a single‐screw extruder. Mechanical properties of the nanocomposites and the dispersion state of CaCO₃ particles in ABS matrix were investigated. The results showed that in CaCO₃/EVA/ABS nanocomposites, CaCO₃ nanoparticles could increase flexural modulus of the composites and maintain or increase their impact strength for a certain nano‐CaCO₃ loading range. The tensile strength of the nanocomposites, however, was appreciably decreased by adding CaCO₃ nanoparticles. The microstructure of neat ABS, CaCO₃/ABS nanocomposites, and CaCO₃/EVA/ABS nanocomposites was observed by scanning electron microscopy. It can be found that CaCO₃ nanoparticles were well‐dispersed in ABS matrix at nanoscale. The morphology of the fracture surfaces of the nanocomposites revealed that when CaCO₃/EVA/ABS nanocomposites were exposed to external force, nano‐CaCO₃ particles initiated and terminated crazing (silver streak), which can absorb more impact energy than neat ABS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of injection‐homo‐polypropylene filled with nano‐CaCO3

Nano‐CaCO₃/homo‐PP composites were prepared by melt‐blending using twin‐screw extruder. The results show that not only the impact property but also the bending modulus of the system have been evidently increased by adding nano‐CaCO₃. The nano‐CaCO₃ particles have been dispersed in the matrix in the nanometer scale which was investigated by means of transmission electron microscopy (TEM). The toughening mechanism of nano‐CaCO₃, investigated by means of dynamical mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM), lies on that the nano‐CaCO₃ particles take an action of initiating and terminating crazing (silver streak), which can absorb more impact energy than the neat PP. At the same time, the nano‐CaCO₃ particles, as the nuclear, decrease the crystal size of PP, the results of which were investigated by means of polarized optical microscope (POM). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Optimization of processing parameters for the synthesis of low‐density polyethylene/organically modified montmorillonite nanocomposites using X‐ray diffraction with experimental design

The influence of the processing parameters on the synthesis of low‐density polyethylene (LDPE)/organically modified montmorillonite (OMM) nanocomposite films was studied using experimental design. Intercalation in the nanocomposites was analysed using X‐ray diffraction and verified using atomic force microscopy. Four direct melt processing parameters were studied to obtain surface maps of intercalation in the nanocomposites: concentration of OMM (clay‐%), concentration of Polybond^® 3149 (compatibilizer‐%), mixing temperature (T_mix) and mixing time. An ANOVA validated the polynomial function, and intercalation maps from response surface methodology (RSM) were obtained. The clay‐% parameter had the most significant effect, and T_mix showed no significant effect on intercalation (p < 0.05). A strong synergic interaction between clay‐% and compatibilizer‐% was observed, which is not possible to detect using univariate experiments. RSM provides a powerful tool for choosing the best processing conditions that lead to formulations with the highest intercalations by considering the main factors and their interactions. © 2013 Society of Chemical Industry     

Processing characteristics of low‐density polyethylene filled with calcium carbonate of different size distributions

Low‐density polyethylene (LDPE) was filled with blends of different proportions of two sizes of calcium carbonate (CaCO₃; 600 and 2500 mesh). The torque of the LDPE/CaCO₃ samples was measured with a torque rheometer. The results showed that the process torque values of the LDPE/CaCO₃ samples obviously decreased when LDPE was filled with a blend of two sizes of CaCO₃ (600‐ and 2500‐mesh CaCO₃ blend) in comparison with samples filled with CaCO₃ of a single size (600 or 2500 mesh). When the ratio of 600‐mesh CaCO₃ to the total CaCO₃ was in the range of 40–60 wt %, the lowest torque value of the LDPE/CaCO₃ samples was achieved. When the content of CaCO₃ in a sample was 30 wt %, LDPE filled with CaCO₃ of different size distributions showed the largest decrease in the torque ratio in comparison with the samples filled with CaCO₃ of a single size. The torques of LDPE samples filled with CaCO₃ of a single size and those filled with CaCO₃ of different size distributions at different temperatures were also studied. The results showed that the flow activation energy and flow activation entropy of LDPE samples filled with CaCO₃ of different size distributions increased obviously. The increase in the flow activation entropy was used to explain the phenomenon of the process torque decreasing for LDPE samples filled with CaCO₃ of different size distributions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and characterization of UV‐curable ZnO/polymer nanocomposite films

A series of novel nano‐ZnO/polymer composite films with different ZnO contents was prepared through incorporation of pre‐made colloidal ZnO particles into monomer mixtures of urethane‐methacrylate oligomer and 2‐hydroxyethyl methacrylate, followed by ultraviolet (UV) radiation‐initiated polymerization. The colloidal ZnO nanoparticles with a diameter of 3–5 nm were synthesized from zinc acetate and lithium hydroxide in ethanol via a wet chemical method. In order to stabilize and immobilize the ZnO particles into the polymer matrix, the ZnO nanoparticles were further capped using 3‐(trimethoxysilyl)propyl methacrylate. Thermogravimetric analyses show that the ZnO nanoparticles were successfully incorporated into the polymer matrix and these ZnO/polymer composites have a good thermal stability. Transmission electron microscopy studies indicate the ZnO nanoparticles were uniformly dispersed in the polymer and they remained at the original size (3–5 nm) before immobilization. All nanocomposite films with ZnO particle contents from 1 to 15 wt% show good transparency in the visible region and luminescent properties. In addition, composite films with high ZnO content (>7 wt%) are able to absorb UV irradiation below 350 nm, indicating that these composite films exhibit good UV screening effects. Copyright © 2006 Society of Chemical Industry     

Effect of surface modifiers and surface modification methods on properties of acrylonitrile–butadiene–styrene/poly(methyl methacrylate)/nano‐calcium carbonate composites

Nano‐calcium carbonate (nano‐CaCO₃) was used in this article to fill acrylonitrile–butadiene–styrene (ABS)/poly(methyl methacrylate) (PMMA), which is often used in rapid heat cycle molding process (RHCM). To achieve better adhesion between nano‐CaCO₃ and ABS/PMMA, nano‐CaCO₃ particles were modified by using titanate coupling agent, aluminum–titanium compound coupling agent, and stearic acid. Dry and solution methods were both utilized in the surface modification process. ABS/PMMA/nano‐CaCO₃ composites were prepared in a corotating twin screw extruder. Influence of surface modifiers and surface modification methods on mechanical and flow properties of composites was analyzed. The results showed that collaborative use of aluminum–titanium compound coupling agent and stearic acid for nano‐CaCO₃ surface modification is optimal in ABS/PMMA/nano‐CaCO₃ composites. Coupling agent can increase the melt flow index (MFI) and tensile yield strength of ABS/PMMA/nano‐CaCO₃ composites. The Izod impact strength of composites increases with the addition of titanate coupling agent up to 1 wt %, thereafter the Izod impact strength shows a decrease. The interfacial adhesion between nano‐CaCO₃ and ABS/PMMA is stronger by using solution method. But the dispersion uniformity of nano‐CaCO₃ modified by solution method is worse. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of nano‐zinc oxide/EPDM composites with both good thermal conductivity and mechanical properties

In this article, nano‐zinc oxide (ZnO) filled ethylene propylene diene monomer (EPDM) composites are prepared, and the mechanical (static and dynamic) properties and thermal conductivity are investigated respectively, which are further compared with the traditional reinforcing fillers, such as carbon black and nano‐silica. Furthermore, influence of in‐situ modification (mixing operation assisted by silane at high temperature for a certain time) with the silane‐coupling agent Bis‐(3‐thiethoxy silylpropyl)‐tetrasufide (Si69) on the nano‐ZnO filled composites is as well investigated. The results indicate that this novel reinforcing filler nano‐ZnO can not only perform well in reinforcing EPDM but can also improve the thermal conductivity significantly. In‐situ modification with Si69 can enhance the interfacial interaction between nano‐ZnO particles and rubber matrix remarkably, and therefore contribute to the better dispersion of filler. As a result, the mechanical properties and the dynamic heat build‐up of the nano‐ZnO filled composites are improved obviously by in‐situ modification, without influencing the thermal conductivity. In comparison with traditioanl reinforcing fillers, in‐situ modified nano‐ZnO filled composites exhibit the excellent performance in both mechanical (static and dynamic) properties and better thermal conductivity. In general, our work indicates that nano‐ZnO, as the novel thermal conductive reinforcing filler, is suitable to prepare elastomer products serving in dynamic conditions, with the longer expected service life. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Foams based on low density polyethylene/hectorite nanocomposites: Thermal stability and thermo‐mechanical properties

Novel polymer nanocomposite foams made by a two step compression molding method are analyzed in this article. Nanocomposites of low density polyethylene and an organo‐modified hectorite were first melt compounded and then foamed using a compression molding method. To study the influence of the presence and the amount of hectorite in both mechanical and thermal properties, samples with 3% and 7% content of hectorite were prepared. Polyethylene crystalline characteristics and thermal stability of the samples were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA), respectively. Mechanical properties of foams and solid nanocomposites were analyzed by using dynamical mechanical analysis (DMA). Thermal expansion of the samples was analyzed by thermomechanical analysis. The results indicate that the exfoliation of hectorite platelets was achieved after the foaming process, but not during the melt mixing step. Foams with hectorite nanoparticles exhibit improved thermal stability and mechanical properties when compared with neat polymeric foams. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Morphology and rheological properties of compatibilized low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch blends

Morphology and rheological properties of low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) blends are experimentally investigated and theoretically analyzed using rheological models. Blending of LDPE/LLDPE (70/30 wt/wt) with 5–20 wt % of TPS and 3 wt % of PE‐grafted maleic anhydride (PE‐g‐MA) as a compatibilizer is performed in a twin‐screw extruder. Scanning electron micrographs show a fairly good dispersion of TPS in PE matrices in the presence of PE‐g‐MA. However, as the TPS content increases, the starch particle size increases. X‐ray diffraction patterns exhibit that with increase in TPS content, the intensity of the crystallization peaks slightly decreases and consequently crystal sizes of the blends decrease. The rheological analyses indicate that TPS can increase the elasticity and viscosity of the blends. With increasing the amount of TPS, starch particles interactions intensify and as a result the blend interface become weaker which are confirmed by relaxation time spectra and the prediction results of emulsion Palierne and Gramespacher‐Meissner models. It is demonstrated that there is a better agreement between experimental rheological data and Coran model than the emulsion models. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44719.     

Effects of ultrasonic oscillations on processing behavior and mechanical properties of metallocene‐catalyzed linear low‐density polyethylene/low‐density polyethylene blends

The influences of ultrasonic oscillations on rheological behavior and mechanical properties of metallocene‐catalyzed linear low‐density polyethylene (mLLDPE)/low‐density polyethylene (LDPE) blends were investigated. The experimental results showed that the presence of ultrasonic oscillations can increase the extrusion productivity of mLLDPE/LDPE blends and decrease their die pressure and melt viscosity during extrusion. Incorporation of LDPE increases the critical shear rate for sharkskin formation of extrudate, crystallinity, and mechanical properties of mLLDPE. The processing behavior and mechanical properties of mLLDPE/LDPE blends were further improved in the presence of ultrasonic oscillations during extrusion. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2522–2527, 2004     

Preparation and characterization of anionically polymerized butadiene‐isoprene copolymer/clay nanocomposites

Butadiene‐isoprene copolymer/montmorillonite (BIR/MMT) nanocomposites were synthesized successfully via in situ anionic polymerization. The results of transmission electron microscopy and X‐ray diffractometer showed that the clay layers were exfoliated and high reaction temperature benefited the exfoliation of layers in BIR/MMT. The polymerization still exhibited “living” characteristics with the addition of organophilic montmorillonite (OMMT). However, the contents of 1,2‐polybutadiene and 3,4‐polyisoprene of the copolymer decreased with the addition of OMMT, because of its absorption effect on N,N,N′,N′‐tetramethylethanediamine as revealed by ¹H NMR. Moreover, it was observed that the glass‐transition temperature of the BIR/MMT nanocomposites also decreased when compared with the BIR copolymers. The thermal stability of the nanocomposites was improved, because of the barrier property of exfoliated clay layers. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 1167–1172, 2006     

Effect of blending high‐pressure low‐density polyethylene on the crystallization kinetics of linear low‐density polyethylene

It is well known that the addition of a small amount of high‐pressure low‐density polyethylene (HP‐LDPE) to linear low‐density polyethylene (LLDPE) can improve the optical properties of LLDPE, and LLDPE/HP‐LDPE blend is widely applied to various uses in the field of film. The optical haziness of polyethylene blown films, as a result of surface irregularities, is thought to be as a consequence of the different crystallization mechanisms. However, not much effort has been directed toward understanding the effect of HP‐LDPE blending on the overall crystallization kinetics (k) of LLDPE including nucleation rate (n) and crystal lateral growth rate (v). In this study, we investigated the effect of blending 20% HP‐LDPE on the crystallization kinetics of LLDPE polymerized by Ziegler‐Natta catalyst with comonomer of 1‐butene. Furthermore, by combining depolarized light intensity measurement (DLIM) and small‐angle laser light scattering (SALLS), we have established a methodology to estimate the lateral growth rate at lower crystallization temperatures, in which direct measurement of lateral growth by polarized optical microscopy (POM) is impossible due to the formation of extremely small spherulites. This investigation revealed that HP‐LDPE blending leads to enhanced nucleation rate, reduced crystal lateral growth rate, and a slight increase in the overall crystallization kinetics of pure LLDPE. From the estimated crystal lateral growth rate, it was found that the suppression in v from HP‐LDPE blending is larger at lower temperatures than at higher temperatures. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and characterization of novel addition cured polydimethylsiloxane nanocomposites using nano‐silica sol as reinforcing filler

A series of novel addition cured polydimethylsiloxane (PDMS) nanocomposites with various amounts of nano‐silica sol were prepared via hydrosilylation for the first time. The influence of various amounts of nano‐silica sol on the morphology, thermal behavior, mechanical and optical properties of these PDMS nanocomposites was studied in detail. It was found that with an increment in the amount of nano‐silica sol the reinforcing effect of the nano‐silica sol on the thermal and mechanical properties of the PDMS nanocomposites was very noticeable compared with the reference material. The prominent improvements in resistance to thermal degradation and mechanical properties can probably be attributed to the strong interaction of PDMS chains and uniformly dispersed particles resulting from the nano‐silica sol. However, the transparency of the PDMS nanocomposites slightly decreased with an increment in weight fraction of nano‐silica, compared with that of PDMS composite without nano‐silica (Sol‐0), which can probably be ascribed to an increasing size of the aggregated particles in the PDMS nanocomposites. The optimum amount of nano‐silica sol for preparing novel addition curing PDMS nanocomposites was about 15 wt%. © 2015 Society of Chemical Industry     

Preparation and characterization of linear low‐density polyethylene/low‐density polyethylene/TiO2 membranes

Because of their special functions, the application of nanoscale powders has recently attracted both industrial and theoretical interest. In this study, nanoscale TiO₂, which exhibited a special UV absorption and consequent antibacterial function, was added to a low‐density polyethylene/linear low‐density polyethylene hybrid by melt compounding to yield functional composite membranes. TiO₂ exhibited an apparent induced nucleation effect on the crystallization of polyethylene, and the size of the crystallites decreased while the number increaed with the introduction of TiO₂; however, the crystallinity of polyethylene changed little. Also, TiO₂ exhibited an ideal dispersion in the membrane with an average size less than 100 nm, and this excellent dispersion provided the membranes extra UV absorption; moreover, the transparency of the membranes was maintained to satisfy common requirements. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 216–221, 2005