Radiation effects on LDPE/EVA blends

Radiation effects of low‐density polyethylene/ethylene‐vinyl acetate copolymer (LDPE/EVA) blends were discussed. EVA content in the LDPE/EVA blends was an enhancement effect on radiation crosslinking of LDPE/EVA blends, and the highest radiation crosslinking was obtained when the EVA content was reached at 30% when irradiated by γ‐ray in air. The phenomenon was discussed with the compatibility, morphology, and thermal properties of LDPE/EVA blends and found that the enhanced radiation crosslinking of the LDPE/EVA blends was proportional to the good compatibility, the increasing degree of the amorphous region's content of the LDPE/EVA blends, and the vinyl acetate content of EVA. We also found that the vinyl acetate of EVA in the blends is easily oxidized by γ‐ray irradiation in air. The possible radiation crosslinking and degradation mechanism of LDPE/EVA blends was discussed quantitatively with a novel method “step‐analysis” process of irradiated LDPE/EVA blends in the thermal gravimetric analysis (TGA) technique. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1296–1302, 2002     

Effect of EVA copolymer on properties of different polyethylenes in silane crosslinking process

Abstract

The effect of molecular structure of polyethylene (PE) [low density PE (LDPE), linear LDPE and high density PE] and silane/peroxide concentration on the grafting level and gel content in silane crosslinking process has been studied. The effect of incorporation of ethylene vinyl acetate (EVA) copolymer on the rate of crosslinking and thermal properties of PEs has been reported. The order of gel content was LDPE>linear LDPE>high density PE. With the incorporation of EVA, the rate of crosslinking increased. The degree of crystallinity did not change with crosslinking significantly. However, the shape of melting and crystallisation peaks changed, and two regions due to gel and sol parts were formed. In EVA/PE blends, two melting points were observed for both crosslinked and uncrosslinked samples. The SEM images showed the droplet matrix morphology with the EVA as the dispersed phase, especially for EVA/LDPE blend. The EVA/PE blends failed in hot set test, while the origin of PEs passed the hot set test successfully.     

Radiation effects on HDPE/EVA blends

In this article, we discuss the radiation effects of high‐density polyethylene (HDPE)/ethylene–vinyl acetate (EVA) copolymer blends. In comparison with the low‐density polyethylene/EVA blends, the EVA content in the HDPE/EVA blends had a lower enhancement effect on radiation crosslinking by γ‐ray irradiation in air. The phenomenon is discussed with the compatibility, morphology, and thermal properties of HDPE/EVA blends. The HDPE/EVA blends were partly compatible in the amorphous region, and radiation crosslinking of the HDPE/EVA blend was less significant, although increasing the amorphous region's content of the HDPE/EVA blends and the vinyl acetate content of EVA were beneficial to radiation crosslinking. The good compatibility was a prerequisite for the enhancement effect of EVA on the radiation crosslinking of the polyethylene/EVA copolymer. The radiation crosslinking and the degradation mechanism of HDPE/EVA blends were examined quantitatively by a novel method, the step analysis process of irradiated HDPE/EVA blends with a thermal gravimetric analysis technique. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 553–558, 2002     

Thermal and wide angle X‐ray analysis of chemically and radiation‐crosslinked low and high density polyethylenes

Low and high density polyethylenes (PE) were crosslinked by two methods, namely, chemically by use of different amounts of tert‐butyl cumyl peroxide (BCUP) and by irradiation with different doses of electron beam. A comparison between the effects of these two types of crosslinking on crystalline structure, crystallinity, crystallization, and melting behaviors of PE was made by wide angle X‐ray diffraction and DSC techniques. Analysis of the DSC first heating cycle revealed that the chemically induced crosslinking, which took place at melt state, hindered the crystallization process and decreased the degree of crystallinity, as well as the size of crystals. Although the radiation‐induced crosslinking, which took place at solid state, had no significant influence on crystalline region, rather, it only increased the melting temperature to some extent. However, during DSC cooling cycle, the crystallization temperature showed a prominent decrease with increasing irradiation dose. The wide angle X‐ray scattering analysis supported these findings. The crystallinity and crystallite size of chemically crosslinked PE decreased with increasing peroxide content, whereas the irradiation‐crosslinked PE did not show any change in these parameters. As compared with HDPE, LDPE was more prone to crosslinking (more gel content) owing to the presence of tertiary carbon atoms and branching as well as owing to its being more amorphous in nature. HDPE, with its higher crystalline content, showed relatively less tendency toward crosslinking especially by way of irradiation at solid state. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3264–3271, 2006     

Dynamic mechanical behavior of high‐density polyethylene/ethylene vinyl acetate copolymer blends: The effects of the blend ratio,reactive compatibilization,and dynamic vulcanization

The effects of the blend ratio, reactive compatibilization, and dynamic vulcanization on the dynamic mechanical properties of high‐density polyethylene (HDPE)/ethylene vinyl acetate (EVA) blends have been analyzed at different temperatures. The storage modulus of the blend decreases with an increase in the EVA content. The loss factor curve shows two peaks, corresponding to the transitions of HDPE and EVA, indicating the incompatibility of the blend system. Attempts have been made to correlate the observed viscoelastic properties of the blends with the blend morphology. Various composite models have been used to predict the dynamic mechanical data. The experimental values are close to those of the Halpin–Tsai model above 50 wt % EVA and close to those of the Coran model up to 50 wt % EVA in the blend. For the Takayanagi model, the theoretical value is in good agreement with the experimental value for a 70/30 HDPE/EVA blend. The area under the loss modulus/temperature curve (LA) has been analyzed with the integration method from the experimental curve and has been compared with that obtained from group contribution analysis. The LA values calculated with group contribution analysis are lower than those calculated with the integration method. The addition of a maleic‐modified polyethylene compatibilizer increases the storage modulus, loss modulus, and loss factor values of the system, and this is due to the finer dispersion of the EVA domains in the HDPE matrix upon compatibilization. For 70/30 and 50/50 blends, the addition of a maleic‐modified polyethylene compatibilizer shifts the relaxation temperature of both HDPE and EVA to a lower temperature, and this indicates increased interdiffusion of the two phases at the interface upon compatibilization. However, for a 30/70 HDPE/EVA blend, the addition of a compatibilizer does not change the relaxation temperature, and this may be due to the cocontinuous morphology of the blends. The dynamic vulcanization of the EVA phase with dicumyl peroxide results in an increase in both the storage and loss moduli of the blends. A significant increase in the relaxation temperature of EVA and a broadening of the relaxation peaks occur during dynamic vulcanization, and this indicates the increased interaction between the two phases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2083–2099, 2003     

Preparation and characterization of low‐density polyethylene/banana starch films containing compatibilizer and photosensitizer

Composite films containing various percentages of banana starch and low‐density polyethylene (LDPE) were prepared. The effects of the compatibilizer, banana starch content, and photosensitizer content on the thermal and tensile properties of these films were investigated. The banana starch content was varied from 5 to 20 wt % of LDPE, whereas benzophenone was added as a photosensitizer in three different amounts (0.25, 0.5, and 1 wt %) based on LDPE. In these films PE‐graft‐maleic anhydride (PE‐g‐MA) was used as a compatibilizer at 10 wt % banana starch. It was found that the thermal stability of the composite films remained unchanged with respect to the amount of banana starch and benzophenone content. The addition of banana starch had no effect on the melting temperature and degree of crystallinity of the films. Similarly, PE‐g‐MA had no effect on the melting temperature but decreased the degree of crystallinity of the LDPE phase. Benzophenone caused an increase in the melting temperature but decreased the degree of crystallinity of LDPE in the films. Increasing the amount of banana starch decreased the tensile properties of the composite films. The addition of PE‐g‐MA as a compatibilizer increased the tensile properties compared with the uncompatibilized films. However, benzophenone had no effect on the tensile properties of the blend films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2717–2724, 2006     

γ-Radiation (0–150 kGy) Effects on Slow and Fast Cooled HDPE/LDPE Blends

Summary The influence of gamma radiation on the morphology, thermal, mechanical and rheological properties of blends of high density polyethylene/low density polyethylene (HDPE/LDPE) was investigated. Prior to irradiation blends of different thermal history were prepared by fast cooling and slow cooling from the melt. Results showed that there were not significant changes in the degree of crystallinity of the blends with radiation. Higher values of degree of crystallinity and melting peak temperature were obtained for the slowly cooled blends. A small increase in the Young modulus and the yield stress were observed by irradiating the blends, and the elongation at break was reduced about 70% when compared to non-irradiated blends. High degree of crosslinking is expected to occur due to the decrease in melt flow rate of the blends irradiated to 50 kGy, and no flow was detected at 150 kGy. Transmission electron microscopy observations failed to show important changes in morphology with radiation.     

Effects of high‐energy electron beam on low‐density polyethylene materials containing EVA

A series of low‐density polyethylene (LDPE) blends with different amounts of ethylene–vinyl–acetate (EVA) was prepared and irradiated with 10 MeV electron beam in the range of 0–250 kGy at room temperature in air. EVA was used as a compatibilizer and softener in four different amounts: 5, 10, 20, and 30 wt %, based on polyethylene (PE). The crosslinking of the samples was studied on the basis of gel‐content measurements as well as some thermal and mechanical properties of the specimens. The results indicated that the LDPE and LDPE–EVA blends could be crosslinked by a high‐energy electron beam, of which their thermal and mechanical properties changed effectively, however, because of EVA content of the polymer; the blends were more sensitive to lower doses of radiation. These studies were carried out to obtain a suitable compound for heat‐shrinkable tubes. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1049–1052, 2004     

Mechanical properties-structure relationships of crosslinked blends based on LDPE/HDPE waste

Low-density polyethylene (LDPE) waste was blended with high-density polyethylene (HDPE) waste of different degrees of degradation. Structural, mechanical and rheological properties of these blends were investigated. It was found that 2 wt.-% of dicumyl peroxide improves simultaneously the tensile strength and elongation at break without serious decrease of the melt elasticity of separate PE wastes and their binary blends in comparison with unmodified PE. It was shown by DSC analyses that modification of the blends leads to better compatibility between LDPE and HDPE.     

Rheology, Morphology and Estimation of Interfacial Tension of LDPE/EVA and HDPE/EVA Blends

Summary Rheological characteristics and morphology of low-density polyethylene (LDPE) /ethylene vinyl acetate copolymer (EVA) and high-density polyethylene (HDPE)/EVA blends were compared. Morphological examinations clearly reveal a two-phase morphology in which the LDPE/EVA blends have smaller dispersed domain size than HDPE/EVA Furthermore, LDPE/EVA shows a finely interconnected morphology at 50wt% of EVA while HDPE/EVA exhibits a coarse co-continuous morphology at the same composition. The morphological observations can be attributed to the lower viscosity ratio and lower interfacial tension in the LDPE/EVA system. The Palierne model also successfully fits to the experimental data giving higher values for interfacial tension of HDPE/EVA system as compared to LDPE/EVA.     

Influence of crosslinking on crystallization,rheological, and mechanical behaviors of high density polyethylene/ethylene‐vinyl acetate copolymer blends

High density polyethylene (HDPE)/ethylene‐vinyl acetate copolymer (EVA) blends with selective crosslinking the EVA phase were prepared and the crystallization, rheological, and mechanical behaviors were studied. Selective crosslinking of EVA component could greatly improve both tensile and impact strengths of the HDPE‐rich blends and influence melting enthalpy at different annealing temperature in successive self‐nucleation and annealing procedure. Dynamic mechanical analysis reveals that glass transition temperatures of both the HDPE and EVA components are lowered upon blending and are raised upon crosslinking. The uncrosslinked HDPE/EVA blends are unstable in the melt and show increment in storage modulus (G′) and decay in loss tangent (tanδ) with annealing time associated with phase coarsening. However, morphology of selectively crosslinked blends in the melt state is highly unstable, characterized by a fast migration of uncrosslinked HDPE component out of the crosslinked EVA phase to the surface resulting in a rapid decay in G′ and an increment in tanδ at the early stage of annealing. POLYM. ENG. SCI., 54:2848–2858, 2014. © 2014 Society of Plastics Engineers     

Effect of electron beam irradiation and vinyl acetate content on the physicochemical properties of LDPE/EVA blends

The radiation‐induced crosslinking, compatibility, and surface modification of low density polyethylene/ethylene vinyl acetate blends (LDPE/EVA) were investigated. The structural and physical properties were characterized in terms of gel content, hot set, mechanical properties, contact angle, and surface free energy. The highest crosslink density was obtained at 20 wt % of EVA. Gel content of LDPE/EVA blends was increased with increasing irradiation dose, vinyl acetate (VA), and EVA contents. The hot set results are consistent with the gel content data. Mechanical testing showed that the tensile strength of samples increased with increasing irradiation dose up to 180 kGy, whereas the elongation at break was decreased with increasing irradiation dose. Contact angle measurements showed that the surface hydrophillicity of LDPE blend was increased with increasing irradiation dose and contents of both VA and EVA. The surface free energy was greatly dependent on irradiation dose and content of both VA and EVA. The total surface free energies of different LDPE formulations were in the range 17.25–32.51 mN/m, in which the polar (^pσ) and disperse (^dσ_s) values were within the range 16.52–26.6 and 0.9–5.91 mN/m, respectively. In conclusion, electron beam irradiation and blending LDPE with EVA improved the wettability or adhesion properties of LDPE/EVA blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Mechanical properties and morphology of polyethylene–polypropylene blends with controlled thermal history

The effect of time–temperature treatment on the mechanical properties and morphology of polyethylene–polypropylene (PE–PP) blends was studied to establish a relationship among the thermal treatment, morphology, and mechanical properties. The experimental techniques used were polarized optical microscopy with hot‐stage, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and tensile testing. A PP homopolymer was used to blend with various PEs, including high‐density polyethylene (HDPE), low‐density polyethylene (LDPE), linear low‐density polyethylene (LLDPE), and very low density polyethylene (VLDPE). All the blends were made at a ratio of PE:PP = 80:20. Thermal treatment was carried out at temperatures between the crystallization temperatures of PP and PEs to allow PP to crystallize first from the blends. A very diffuse PP spherulite morphology in the PE matrix was formed in partially miscible blends of LLDPE–PP even though PP was present at only 20% by mass. Droplet‐matrix structures were developed in other blends with PP as dispersed domains in a continuous PE matrix. The SEM images displayed a fibrillar structure of PP spherulite in the LLDPE–PP blends and large droplets of PP in the HDPE–PP blend. The DSC results showed that the crystallinity of PP was increased in thermally treated samples. This special time–temperature treatment improved tensile properties for all PE–PP blends by improving the adhesion between PP and PE and increasing the overall crystallinity. In particular, in the LLDPE–PP blends, tensile properties were improved enormously because of a greater increase in the interfacial adhesion induced by the diffuse spherulite and fibrillar structure. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1151–1164, 2000     

An investigation of chemical crosslinking effect on properties of high-density polyethylene

High-density polyethylene (HDPE) was chemically crosslinked with various amounts of di-tert butyl cumyl peroxide (BCUP). Crosslink density determined by rubber elasticity theory using hot set test showed an increase with increasing BCUP. Glass transition temperature (T_g), thermal stability, crystallization, melting behavior and tensile properties were studied. The results showed a new finding about decrease in T_g as a consequence of the ‘chemical crosslinking’ of HDPE. This was explained by observed reduction in crystallinity and expected increase in free volume as a result of restriction in chain packing. However, chemical crosslinking had no significant effect on the thermal stability. The stress at break, Young's modulus yield strength and elongation at break generally decreased with increase in BCUP. By increasing the temperature for slightly crosslinked HDPE, the elongation at break was increased but by increasing the crosslinking level an opposite effect was observed. Crosslinked HDPE showed an decrease in creep strain and an increase in creep modulus with increasing BCUP.     

不同密度聚乙烯共混物性质的研究

讨论了HDPE与LDPE及HDPE与LLDPE共混物的性质。研究表明共混物的力学性能、结晶度、熔点及维卡软化点都随密度ρ的变化呈规律性变化,由此总结出综合性能较好的共混物密度范围。     

Blends of high‐density polyethylene with solid silicone additive

Silicone masterbatch (SMB) is a pelletized formulation containing 50% of an ultrahigh molecular‐weight polydimethylsiloxane dispersed in polyethylene. This SMB is designed to be used as an additive in polyethylene‐compatible systems to impart benefits such as processing improvement and modification of surface characteristics. In this work, binary blends of high‐density polyethylene (HDPE) and SMB were prepared by melt‐mixing technique to study the influence of this masterbatch on the processing and mechanical properties of HDPE. Ternary blends were also prepared by the addition of silane‐grafted polyethylene (HDPE‐VTES) as compatibilizer. The blends were analyzed by melting flow rate (MFR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and tensile tests. Data of final torque and MFR showed that SMB improved the processability of pure HDPE. DSC results showed differences in crystalline behavior between binary and ternary blends. In the former, the degree of crystallinity increased up to 10 wt % of SMB content; beyond this concentration, it decreased. In ternary blends, a reverse behavior was observed. The morphologic study showed silicone particles uniformly distributed in HDPE matrix. With high SMB concentration, the addition of HDPE‐VTES significantly reduced the size of silicone particles. In the range of SMB composition studied, the mechanical properties of blends lower slightly compared to pure HDPE. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2347–2354, 2002     

Effects of polyethylene‐grafted maleic anhydride (PE‐g‐MA) on thermal properties,morphology, and tensile properties of low‐density polyethylene (LDPE) and corn starch blends

The effects of polyethylene‐grafted maleic anhydride (PE‐g‐MA) on the thermal properties, morphology, and tensile properties of blends of low‐density polyethylene (LDPE) and corn starch were studied with a differential scanning calorimeter (DSC), scanning electron microscope (SEM), and Instron Universal Testing Machine, respectively. Corn starch–LDPE blends with different starch content and with or without the addition of PE‐g‐MA were prepared with a lab‐scale twin‐screw extruder. The crystallization temperature of LDPE–corn starch–PE‐g‐MA blends was similar to that of pure LDPE but higher than that of LDPE–corn starch blends. The interfacial properties between corn starch and LDPE were improved after PE‐g‐MA addition, as evidenced by the structure morphology revealed by SEM. The tensile strength and elongation at break of corn starch–LDPE–PE‐g‐MA blends were greater than those of LDPE–corn starch blends, and their differences became more pronounced at higher starch contents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2904–2911, 2003     

Morphology and rheological properties of compatibilized low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch blends

Morphology and rheological properties of low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) blends are experimentally investigated and theoretically analyzed using rheological models. Blending of LDPE/LLDPE (70/30 wt/wt) with 5–20 wt % of TPS and 3 wt % of PE‐grafted maleic anhydride (PE‐g‐MA) as a compatibilizer is performed in a twin‐screw extruder. Scanning electron micrographs show a fairly good dispersion of TPS in PE matrices in the presence of PE‐g‐MA. However, as the TPS content increases, the starch particle size increases. X‐ray diffraction patterns exhibit that with increase in TPS content, the intensity of the crystallization peaks slightly decreases and consequently crystal sizes of the blends decrease. The rheological analyses indicate that TPS can increase the elasticity and viscosity of the blends. With increasing the amount of TPS, starch particles interactions intensify and as a result the blend interface become weaker which are confirmed by relaxation time spectra and the prediction results of emulsion Palierne and Gramespacher‐Meissner models. It is demonstrated that there is a better agreement between experimental rheological data and Coran model than the emulsion models. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44719.     

Raman spectra of high‐density,low‐density,and linear low‐density polyethylene pellets and prediction of their physical properties by multivariate data analysis

Raman spectra have been measured for pellets of five samples of high‐density polyethylene (HDPE), seven samples of low‐density polyethylene (LDPE), and six samples of linear low‐density polyethylene (LLDPE). The obtained Raman spectra have been compared to find out characteristic Raman bands of HDPE, LDPE, and LLDPE. Principal component analysis (PCA) was applied to the Raman spectra in the 1600–650 cm^?1 region after multiplicative scatter correction (MSC) to discriminate the Raman spectra of the three different PE species. They are classified into three groups by a score plot of PCA factor 1 vs. 2. HDPE with high density and high crystallinity gives high scores on the factor 1 axis, while LDPE with low density and low crystallinity yields negative scores on the same axis. It seems that factor 1 reflects the density or crystallinity. A PC weight loadings plot for factor 1 shows six upward peaks corresponding to the bands arising from the crystalline parts or all‐trans ? (CH₂)_n? groups and seven downward peaks ascribed to the bands of the amorphous or anisotropic regions and those arising from the short branches. Partial least‐squares (PLS‐1) regression was applied to the Raman spectra after MSC to propose calibration models that predict the density, crystallinity, and melting points of the polyethylenes. The correlation coefficient was calculated to be 0.9941, 0.9800, and 0.9709 for the density, crystallinity, and melting point, respectively, and their root‐mean‐square error of cross validation (RMSECV) was found to be 0.0015, 3.3707, and 2.3745, respectively. The loadings plot of factor 2 for the prediction of melting point is largely different from those for the prediction of density and crystallinity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 443–448, 2002     

Co‐crystallization in ternary polyethylene blends: tie crystal formation and mechanical properties improvement

Understanding the co‐crystallization behavior of ternary polyethylene (PE) blends is a challenging task. Herein, in addition to co‐crystallization behavior, the rheological and mechanical properties of melt compounded high density polyethylene (HDPE)/low density polyethylene (LDPE)/Zeigler ? Natta linear low density polyethylene (ZN‐LLDPE) blends have been studied in detail. The HDPE content of the blends was kept constant at 40 wt% and the LDPE/ZN‐LLDPE ratio was varied from 0.5 to 2. Rheological measurements confirmed the melt miscibility of the entire blends. Study of the crystalline structure of the blends using DSC, wide angle X‐ray scattering, small angle X‐ray scattering and field emission SEM techniques revealed the formation of two distinct co‐crystals in the blends. Fine LDPE/ZN‐LLDPE co‐crystals, named tie crystals, dispersed within the amorphous gallery between the coarse HDPE/ZN‐LLDPE co‐crystals were characterized for the first time in this study. It is shown that the tie crystals strengthen the amorphous gallery and play a major role in the mechanical performance of the blend.© 2016 Society of Chemical Industry