Mass Transfer in a Flat Gas/Liquid Interface using non‐Newtonian Media

Gas/liquid mass transfer has been investigated using a stirred vessel gas/liquid contactor using non‐Newtonian media and carbon dioxide as absorbent and gas phase, respectively. The volumetric mass transfer coefficients at different operational variables have been determined. Non‐Newtonian media (liquid phase) were prepared as aqueous solutions of sodium carboxymethyl cellulose salt. The influence of the rheological properties, polymer concentration, stirring rate, and gas flow rate on mass transfer was studied for these liquid phases. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymer employed. The Ostwald model has been used to fit the rheological behavior of aqueous solutions of the polymer employed as absorbent phase. Reasonably good agreement was found between the predictions of the proposed models and the experimental data of mass transfer coefficients.     

Development of airlift bubble column dispersed with micro‐bubbles

Micro‐bubbles were dispersed in the bubble column with draft tube, and the length and diameter of draft tube were changed. The flow characteristics in air–water system were measured. Ozone gas and methylene‐blue aqueous solution were used, and the decomposition performance was examined. With increasing draft tube length, both the gas holdup and liquid velocity in the annular section increased. When the diameter ratio of draft tube to column was about 0.5, both the gas holdup and liquid circulation flow rate had maxima. For the decomposition by using ozone, the installation of draft tube enhanced the mass transfer and decomposition performance.     

Effects of Gas‐Agitation and Packing on Hydrodynamics and Mass Transfer of Extraction Column

The effects of gas‐agitation and packing on hydrodynamics and mass transfer were investigated through experiments with air‐kerosene (benzoic acid)‐water system and corrugated‐packing of calendering plate with hole. The holdup of gas, holdup of dispersed liquid phase and mass transfer coefficient increase and the flooding velocity decrease with the increase in superficial gas velocity. Over‐agitation of gas causes over‐dispersion and emulsification of dispersed liquid phase, reduction of mass transfer performance and even flooding. The mass transfer performance of a packed column is far better than that of an unpacked column.     

Analysis of carbon dioxide gas/liquid mass transfer in aerated stirred vessels using non–Newtonian media

Gas/liquid mass transfer has been investigated in an aerated stirred tank using non‐Newtonian media and carbon dioxide as absorbent and gas phase respectively. The volumetric mass transfer coefficients at different operational variables have been measured. The non‐Newtonian media (liquid phases) used were aqueous solutions of two polymers, carboxymethyl cellulose and alginate sodium salts. The influence upon the mass transfer of the rheological properties, polymer concentration, stirring rate and gas flow rate was studied. Kinematic viscosity and density experimental data were used to calculate the average molecular weight corresponding to the polymers employed. Reasonable agreement was found between the predictions of proposed models and the experimental data. The results shown in the present paper allow us to understand carbon dioxide transfer to a non‐Newtonian liquid phase and to evaluate the effect of the liquid phase characteristics. The equations used in this paper allow accurate simulation of the transfer of a pure gas to a rheologically complex solution. Copyright © 2004 Society of Chemical Industry     

Bubble Volume and Aspect Ratio Generated in Non‐Newtonian Fluids

Bubble formation from an orifice submerged in quiescent polyacrylamide aqueous solution was investigated numerically with a sharp‐interface coupled level‐set/volume‐of‐fluid method based on the rheological characteristics of the fluid. In both non‐Newtonian fluids and Newtonian fluids, the numerical approach was able to capture accurately the deformation of the bubble surface, validated by comparison with experimental results. The effects of orifice diameter, solution mass concentration, and gas flow rate on bubble volume and aspect ratio were evaluated. Both the instantaneous and detached volume decrease with the orifice diameter but increase with mass concentration and gas flow rate. The aspect ratio at the departing point tends to rise with the orifice diameter and mass concentration and falls with the gas flow rate.     

Mass transfer and hydrodynamic characteristics in a co‐current downflow contacting column

Hydrodynamic and mass transfer characteristics of water–air system in a co‐current downflow contacting column (CDCC) were studied for various nozzle diameters at different superficial gas velocities and liquid re‐circulation rates. Gas hold‐up and liquid‐side mass transfer coefficient increased with increasing superficial gas velocity and liquid flow rate but decreased with increasing nozzle diameter. It is shown that correlations developed, which are based on liquid kinetic power per liquid volume present in the column, and superficial gas velocity explains gas hold‐up and the mass transfer coefficient within an error 20% for all gas and liquid flow rates and nozzle diameters used. The constants of correlations for gas hold‐up and mass transfer coefficient were found to be considerably different from other gas–liquid contacting systems. © 2003 Society of Chemical Industry     

Effect of aeration mode on the performance of center‐ and annulus‐rising internal‐loop airlift bioreactors

Extensive experimental studies on internal‐loop airlift reactors, including center‐rising (CR‐ALR) and annulus‐rising airlift reactors (AR‐ALR), have been reported in the literature. However, to the best of the authors’ knowledge, the effects of the aeration mode on the local hydrodynamics remain an under‐investigated area, especially for complex culture media. At present, it is difficult to select the best aeration mode for ALRs due to limited understanding of the pros and cons of the different modes. This study presents a detailed quantitative investigation of the overall gas holdup, local liquid velocity, liquid circulation time, shear rate distribution, and volumetric mass transfer coefficient in center‐ and annulus‐rising airlift bioreactors to better understand the effect of aeration mode on airlift bioreactor performance. Particle image velocimetry is employed to conduct local measurements. The results show that the overall gas holdup, liquid circulation time, and volumetric mass transfer coefficient are larger in the AR‐ALR than in the CR‐ALR. The local liquid velocity circulating into the downcomer of the AR‐ALR, which contributes to bubble entrainment and therefore to overall gas holdup, is higher than in the CR‐ALR. It was observed that a large circulation loop formed in the CR‐ALR, whereas two counter‐looping circulation cells appeared in the AR‐ALR. It was also found that the shear rate field was more uniform in the AR‐ALR than the CR‐ALR although the shear rates were similar in magnitude.     

Local hydrodynamic parameters of bubble column reactors operating with non‐Newtonian liquids: Experiments and models development

The effects of liquid phase rheology on the local hydrodynamics of bubble column reactors operating with non‐Newtonian liquids are investigated. Local bubble properties, including bubble frequency, bubble chord length, and bubble rise velocity, are measured by placing two in‐house made optical fiber probes at various locations within a bubble column reactor operating with different non‐Newtonian liquids. It was found that the presence of elasticity can noticeably increase the bubble frequency but decreases the bubble chord length and its rise velocity. The radial profiles of bubble frequency, bubble chord length, and bubble rise velocity are shown to be relatively flat at low superficial gas velocity while they become parabolic at high superficial gas velocity. Moreover, the bubble size and gas holdup are correlated with respect to dimensionless groups by considering the ratio between dynamic moduli of viscoelastic liquids. The novel proposed correlations are capable of predicting the experimental data of bubble size and gas holdup within a mean absolute percentage error of 9.3% and 10%, respectively. © 2015 American Institute of Chemical Engineers AIChE J, 62: 1382–1396, 2016     

Gas—liauid mass transfer in three-phase stirred tank reagors: Newtonian and non-newtonian fluids

Gas—liquid mass transfer has been investigated in gas—liquid-solid three-phase stirred tank reactors with Newtonian and non-Newtonian liquids. Volumetric mass transfer coefficients and gas hold-ups were measured in a 0.2 m i.d. stirred tank reactor and the effects of low-density polymeric particles (ρ_s, =1030 and 1200 kg/m³; up to 15 vol%) on gas—liquid mass transfer were examined. The volumetric mass transfer coefficients in water were found to decrease due to the presence of solid particles at constant impeller speed and superficial gas velocity. On the other hand, solids loading led to higher mass transfer rates in non-Newtonian carboxymethyl cellulose aqueous solutions. Our previously proposed model for mass transfer in gas—liquid two-phase systems was extended to gas—liquid—solid three-phase systems. Reasonable agreement was found between the predictions of the proposed model and the experimental data.     

鼓泡反应器中幂律型流体流动与传质特性

很多废水处理装置涉及非牛顿型流体中的多相流动和传质问题,研究其中的气液传质过程有助于实现装置的优化设计和高效节能运行。以鼓泡反应器内清水和不同质量分数的羧甲基纤维素钠（CMC）水溶液为实验对象,分别研究气相表观气速和液相流变特性对气泡尺寸分布、全局气含率和体积氧传质系数的影响。实验结果表明,液相的流变特性对其传质特性参数均有较大影响。与清水相比,CMC水溶液中气泡平均直径和分布范围更大;清水和CMC水溶液的全局气含率均随表观气速的增加而增大;CMC水溶液的体积氧传质系数随CMC水溶液质量分数的增加而减小。基于实验研究,得出修正的体积氧传质系数公式和适用于幂律型非牛顿流体流动体系氧传递过程的无量纲关联式,可很好地实现非牛顿流体流动的废水处理装置中气液传质参数的计算。     

Pressure Drop Models for Gas/Non‐Newtonian Power‐Law Fluids Flow in Horizontal Pipes

Models commonly used in literature are evaluated versus 696 data points to predict the pressure drop of gas/non‐Newtonian power‐law fluids flow in horizontal pipes. Suitable models are recommended. A new correlation is developed by ignoring the pressure drop across the gas slug and adopting the liquid slug holdup of gas/non‐Newtonian fluid flow into the homogeneous model. The theoretical curves can capture the test data trends and the overall agreement of predicted values with experimental data is sufficient to be practically applied in industry.     

Mass transfer into/from nanofluid drops in a spray liquid‐liquid extraction column

The performance of a spray liquid‐liquid extraction column at two mass‐transfer directions was experimentally studied in the presence of silica nanoparticles. Toluene‐based nanofluid drops containing 0.0005–0.01 vol % silica nanoparticles were dispersed in aqueous phase and acetic acid (AA) transfer between phases was investigated. The experiments were performed at fixed volumetric flow rates of dispersed and continuous phases. Maximum enhancement of 47.4% and 107.5% in overall mass‐transfer coefficient, respectively, for mass‐transfer direction of dispersed to continuous phase and vice versa were achieved for drops with 0.001 vol % silica nanoparticles. These enhancements can be referred to Brownian motion of nanoparticles and induced microconvection. The results showed that nanoparticles are more effective in augmenting AA transfer from continuous to dispersed phase. Probable reason is that smaller diameter and lower internal turbulence of drops in this transfer direction increase dispersed phase resistance potential to be manipulated by Brownian motion of nanoparticles. © 2015 American Institute of Chemical Engineers AIChE J, 62: 852–860, 2016     

三相下喷式环流反应器的传质性能

在三相非牛顿型流体体系中，对下喷式环流反应器传质特性进行了实验研究。讨论了表观气速、能量耗散速率、导流筒直径与反应器直径比、喷嘴直径、导流筒下端距反应器底部的距离、固体装填量、羧甲基纤维素钠（ＣＭＣ）溶液浓度及其流变特性对它的影响。实验结果表明，容积传质系数随表观气速和能量耗散速率的增加有所增加，在实验条件下，发现最优的导流筒直径与反应器直径比在０．４～０．４５这一范围、固体装填量大约为３％（体积百分比）、导流筒下端距反应器底部的距离为０．０８ｍ左右。同时提出了容积传质系数的经验关联式。     

Experimental investigations of non‐Newtonian/Newtonian liquid‐liquid flows in microchannels

The plug flow of a non‐Newtonian and a Newtonian liquid was experimentally investigated in a quartz microchannel (200‐µm internal diameter). Two aqueous glycerol solutions containing xanthan gum at 1000 and 2000 ppm were the non‐Newtonian fluids and 0.0046 Pa s silicone oil was the Newtonian phase forming the dispersed plugs. Two‐color particle image velocimetry was used to obtain the hydrodynamic characteristics and the velocity profiles in both phases under different fluid flow rates. The experimental results revealed that the increase in xanthan gum concentration produced longer, bullet‐shaped plugs, and increased the thickness of the film surrounding them. From the shear rate and viscosity profiles, it was found that the polymer solution was in the shear‐thinning region while the viscosity was higher in the middle of the channel compared to the region close to the wall. Circulation times in the aqueous phase increased with the concentration of xanthan gum. © 2017 The Authors AIChE Journal published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers AIChE J, 63: 3599–3609, 2017     

Gas holdup in homogeneous and heterogeneous gas—liquid bubble column reactors

The velocity‐holdup relationship is the most important design parameter for gas—liquid bubble column reactors, providing the basis for the prediction of heat and mass transfer coefficients and information on hydrodynamic conditions. A summary of the literature on gas holdup in bubble columns is supplemented by new experimental results which extend the data range. A criterion for the gas velocity leading to the transition between homogeneous and heterogeneous regimes for perforated plate gas distributors has been developed. Correlations for gas holdup in both regimes are developed and verified against both new and existing data.     

Carbon Dioxide Absorption in Triethanolamine Aqueous Solutions: Hydrodynamics and Mass Transfer

The carbon dioxide absorption process by triethanolamine aqueous solutions was analyzed in a bubble‐column reactor taking into account the chemical reaction mechanism, gas‐liquid interfacial area, and mass transfer rate. A speciation study of this gas‐liquid system was developed by ¹H and ¹³C NMR spectroscopy in order to obtain the reaction mechanism and stoichiometry. The gas‐liquid interfacial area was evaluated considering the variations of bubble size distribution and gas holdup during the operation time. The liquid‐phase mass transfer coefficient was calculated from the carbon dioxide absorption rate data by interfacial area evolution and reaction stoichiometry.     

OXYGEN TRANSFER IN THE WATER-JET VESSEL

This is an investigation of the gas holdup and the volumetric mass transfer coefficient of a plunging water jet in an air-water system. We sound k_La to be directly proportional to gas holdup in two regions. For the first time, this has been clarified in the plunging liquid jet system. The volumetric mass transfer coefficient and the gas holdup have been well correlated in terms of the Froude number, liquid jet length, nozzle diameter and vessel diameter.     

Study of Hydrodynamics,Mixing and Gas‐Liquid Mass Transfer in a Split‐Rectangular Airlift Reactor

Global hydrodynamic characteristics, liquid mixing and gas‐liquid mass transfer for a 63 L split‐rectangular airlift reactor were studied. Correlations for gas holdup and overall liquid circulation velocity were derived for the air‐water system as a function of the specific power input; these were compared to data and correlations for reactor volumes between 4.7 L and 4600 L. A partial recirculation of small bubbles in the riser was observed when U_gr > 0.03 m/s, which was attributed to the use of a single‐orifice nozzle as the gas phase distributor. The dimensionless mixing time and the overall axial dispersion coefficient were nearly constant for the range of gas flow rates studied. However, values of K_L/d_B were greater than those reported in previous studies and this is caused by the partial recirculation of the gas phase in the riser. While scale effects remain slight, the use of a gas distributor favouring this partial recirculation seems adequate for mass transfer in split‐rectangular airlift reactors.     

A Simple Approach to Measuring the Gas Phase Heat and Mass Transfer Coefficients in a Bubble Column

A simple experimental approach was developed to measure the gas phase volumetric heat and mass transfer coefficients in a bubble column and a slurry bubble column employing a single gas nozzle. The experimental technique was based on a transfer model that simulates humidification and direct contact evaporation models in the case of a gas bubble rising in a liquid of uniform temperature. The temperature and relative humidity of the inlet and outlet gas in the column are the only measurements required in this technique. Experiments were carried out in a 0.15 m inner diameter column using water as the liquid phase, air as the gas phase, and cation resins of 0.1 mm diameter and a specific gravity of 1.2, as the solid phase. The results showed that, when using solid concentrations in the range of 7–10 wt %, both the volumetric gas‐phase heat and mass transfer coefficients increased with an increase in the gas superficial velocity and were further enhanced by increasing the solid load after a certain minimum superficial velocity had been reached in the column (0.044 m/s in the system used). Increasing the solid load beyond 10 wt %, did not contribute to a further increase in these coefficients. Furthermore, the gas holdup in the column increased with the superficial gas velocity and was further enhanced when the solid‐phase load was in the range of 7–10 wt %. These observations agree well with previously reported findings by other investigators.