Polymerization of norbornene using bis(β‐ketoamino)nickel(II)/MAO catalytic systems

The polymerizations of norbornene were investigated using a series of bis(β‐ketoamino)nickel(II) complexes( 1–6 ) in combination with methylaluminoxane (MAO) in toluene solution. The effects of catalyst structure, Al/Ni molar ratio, reaction temperature, and reaction time on catalytic activity and molecular weight of the polynorbornene were examined in detail. The electronic effect of the substituent around the imino group in the ligand is stronger than the steric bulk one on the polymerization activities, and the activities are in the order of 1 > 2 > 4 > 5 > 6 > 3 . The obtained polynorbornenes were characterized by means of ¹H‐NMR, ¹³C‐NMR, FTIR, TG, and WAXD techniques. The analyses results of polymers' structures and properties indicate that the polymerization reaction of norbornene runs in vinyl‐addition polymerization mode. The obtained polynorbornene was confirmed to be vinyl‐type and atactic polymers and showed good thermostability (T_dec > 458°C) and were noncrystalline but had short‐range order. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4172–4180, 2006     

Polymerization of styrene using pyrazolylimine nickel (II)/methylaluminoxane catalytic systems

The polymerization of styrene with two pyrazolylimine nickel (II) complexes of (2-(C₃HN₂Me₂-3, 5)(C(Ph) = N(4-R₂C₆H₂(R₁)₂-2, 6)NiBr₂ (Complex 1 , R₁ = ⁱPr, R₂ = H; Complex 2 , R₁ = H, R₂ = NO₂)) activated by methylaluminoxane was studied. The influences of polymerization parameters such as polymerization temperature, Al/Ni molar ratio, and reaction time on catalytic activity and molecular weight of the polystyrene (PS) were investigated in detail. The electron-withdrawing of nitro group in Complex 2 could not enhance the catalytic activity for styrene polymerization; however, the molecular weights of polymers were increased. Both of the two catalytic systems exhibited high activity [up to 8.45 × 10⁵ gPS/(mol Ni h)] for styrene polymerization and provide PS with moderate to low-molecular weights (M_w = 2.21 × 10⁴∼ 5.71 × 10³ g/mol) and narrower molecular weight distributions about 2.0. The obtained PS were characterized by means of IR, ¹H NMR, and ¹³C NMR techniques. The results indicated that the PS was atactic polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Polymerization of styrene using novel bispyrazolylimine dinickel (II)/methylaluminoxane catalytic systems

The polymerization of styrene with a series of bispyrazolylimine dinickel (II) complexes of bis‐2‐(C₃HN₂(R₁)₂‐3,5)(C(R₂) = N(C₆H₃(CH₃)₂‐2,6)Ni₂Br₄ (complex 1 : R₁ = CH₃, R₂ = Ph; complex 2 : R₁ = CH₃, R₂ = 2,4,6‐trimethylphenyl; complex 3 : R₁ = R₂ = Ph; complex 4 : R₁ = Ph, R₂ = 2,4,6‐trimethylphenyl) in the presence of methylaluminoxane (MAO) was studied. The influences of polymerization parameters such as polymerization temperature, Al/Ni molar ratio, reaction time, and catalyst concentration on catalytic activity and molecular weight of the polystyrene were investigated in detail. The influence of the bulkiness of the substituents on polymerization activity was also studied. All of the four catalytic systems exhibited high activity (up to 10.50 × 10⁵ gPS/(mol Ni h)) for styrene polymerization and provide polystyrene with moderate to low molecular weights (M_w = 4.76 × 10⁴–0.71 × 10⁴ g/mol) and narrower molecular weight distributions about 2. The obtained polystyrene was characterized by means of FTIR, ¹H‐NMR, and ¹³C‐NMR techniques. The results indicated that the polystyrene was atactic polymer. The analysis of the end groups of polystyrene indicated that styrene polymerization with bispyrazolylimine dinickel complexes/MAO catalytic systems proceeded through a coordination mechanism. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Vinyl‐addition copolymerization of norbornene and polar norbornene derivatives using novel bis(β‐ketoamino)Ni(II)/B(C6F5)3/AlEt3 catalytic systems

Copolymerization of norbornene (NBE) and polar norbornene derivatives undergoes vinyl polymerization by using novel catalyst systems formed in situ by combining bis(β‐ketoamino)Ni(II) complexes {Ni[R₁C(O)CHC(NR₃)R₂]₂ (R_l = R₂ = CH₃, R₃ = naphthyl, 1 ; R₁ = R₂ = CH₃, R₃ = C₆H₅, 2 ; R₁ = C₆H₅, R₂ = CH₃, R₃ = naphthyl, 3 ; R_l = R₂ = CH₃, R₃ = 2, 6‐(CH₃)₂C₆H₃, 4 ; R₁ = R₂ = CH₃, R₃ = 2, 6‐′Pr₂C₆H₃ 5 ; R₁ = C₆H₅, R₂ = CH₃, R₃ = 2, 6‐′Pr₂C₆H₃, 6 )} and B(C₆F₅)₃/AlEt₃ in toluene. The 1 /B(C₆F₅)₃/AlEt₃ catalytic system is effective for copolymerization of NBE with NBE OCOCH₃ and NBE CH₂OH, respectively, and copolymerization activity is followed in the order of NBE CH₂OH > NBE OCOCH₃ > NBE CN. The molecular weights of the obtained poly(NBE/NBE CH₂OH) reached 5.97 × 10⁴ to 2.07 × 10⁵ g/mol and the NBE CH₂OH incorporation ratios reached 7.0–55.4 mol % by adjusting the comonomer feedstock composition. The copolymerization of NBE and NBE CH₂OH also depend on catalyst structures and activity of catalyst followed in the order of 2 > 1 > 3 > 5 > 4 > 6 . The molecular weights and NBE CH₂OH incorporation ratios of poly(NBE/NBE CH₂OH) were adjustable to be 1.91–5.37 × 10⁵ g/mol and 9.5–41.1 mol %  OH units by using catalysts 1 – 6 . The achieved copolymers were confirmed to be vinyl‐addition type, noncrystalline and have good thermal stability (T_d = 380–410°C). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Styrene–substituted‐styrene copolymerization using diphenylzinc–metallocene–methylaluminoxane systems

Homopolymerization of disubstituted styrenes (2,4‐ and 2,5‐dimethylstyrene) and trisubstituted styrene (2,4,6‐trimethylstyrene) and their copolymerization with styrene were carried out using diphenylzinc–metallocene–methylaluminoxane initiator systems for metallocene (n‐BuCp)₂TiCl₂ and for half‐metallocene CpTiCl₃. The studied comonomers were found to be less reactive than p‐tertbutylstyrene, p‐methylstyrene and styrene. The results indicate that, even though the methyl group has I+ inductive effect, di‐ and tri‐methylstyrenes are reluctant to undergo either homopolymerization or copolymerization. This behavior suggests that the reactivity is regulated not only by the inductive effect of the alkyl group but also by the steric impediment caused by the crowding of the substituents on the benzene ring. Copyright © 2006 Society of Chemical Industry     

Polymerization of methyl methacrylate catalyzed by mono-/bis-salicylaldiminato nickel(II) complexes and methylaluminoxane

Two types of salicylaldiminato-based nickel complexes, mono-ligated Ni(II) complexes ([O-C₆H₄-o- C(H)=N-Ar]Ni(PPh₃)(Ph) (5), [O-(3,5-Br₂)C₆H₂-o-C(H)=N-Ar]Ni(PPh₃)(Ph) (6), [O-(3-t-Bu)C₆H₃-o-C(H)=N-Ar]Ni(PPh₃)(Ph) (7)) and bis-ligated Ni(II) complexes ([O-(3,5-Br₂)C₆H₂-o-C(H)=N-Ar]₂Ni (8), [O-(3,5-Br₂)C₆H₂-o-C(H)=N-2-C₆H₄(PhO)]₂Ni (9), Ar=2,6-C₆H₃(i-Pr)₂) were synthesized and characterized by Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance (NMR), mass spectrography (MS) and elemental analysis (EA). In the presence of methylaluminoxane (MAO) as cocatalyst, all the nickel complexes exhibited high activities for the polymerization of methyl methacrylate (MMA) and syndiotactic-rich poly(methyl methacrylate) (PMMA) was obtained. The complexes with less bulky substituents on salicylaldiminato framework possessed higher activities, while with the same salicylaldiminato, the mono-ligated nickel complexes showed higher catalytic activity than bis-ligated ones.     

Synthesis of branched polyethylene by ethylene homopolymerization with a novel (α‐diimine)nickel complex in the presence of methylaluminoxane

Branched polyethylene (PE) was prepared with a novel (α‐diimine)nickel(II) complex of 2,3‐bis(2,6‐dimethylphenyl)‐butanediimine nickel dichloride {[2,6‐(CH₃)₂C₆H₃? N?C(CH₃)C(CH₃)?N? 2,6‐(CH₃)₂C₆H₃]NiCl₂} activated by methylaluminoxane in the presence of a single ethylene monomer. The influences of various polymerization conditions, including the temperature, Al/Ni molar ratio, Ni catalyst concentration, and time, on the catalytic activity, molecular weight, degree of branching, and branch length of PE were investigated. According to gel permeation chromatography, the weight‐average molecular weights of the polymers obtained ranged from 1.7 × 10⁵ to 6.0 × 10⁵, with narrow molecular weight distributions of 2.0–3.5. The degree of branching in the polymers rapidly increased with the polymerization temperature increasing; this led to highly crystalline to totally amorphous polymers, but it was independent of the Al/Ni molar ratio and catalyst concentration. At polymerization temperatures greater than 20°C, the resultant PE was confirmed by ¹³C‐NMR to contain significant amounts of not only methyl but also ethyl, propyl, butyl, amyl, and long branches (longer than six carbons). The formation of the branches could be illustrated by the chain walking mechanism, which controlled their specific spacing and conformational arrangements with one another. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1123–1132, 2002; DOI 10.1002/app.10398     

Homopolymerization of n‐butyl methacrylate using bis(salicylaldiminate)copper(II)/ methylaluminoxane catalysts

Polymerization catalysts based on copper precursors appear particularly interesting due to the low metal cost, limited toxicity and modest sensitivity to deactivation by polar species. To date, α‐olefin and polar monomer coordination polymerization catalysed using copper catalysts has been scarcely investigated, and a good part of the literature is represented by patents. Here this research has been expanded to the study of the performances of bis(salicylaldiminate)copper(II)/methylaluminoxane (MAO) catalysts in the polymerization of n‐butyl methacrylate. The study of the catalytic activity of bis(salicylaldiminate)copper(II)/MAO systems in n‐butyl methacrylate polymerization was focused on the relationship between the catalytic behaviour and the main reaction conditions and ligand structures. The electronic and steric characteristics of the chelate ligands play an important role in the catalytic performances. The presence of electron‐withdrawing nitro groups on the chelate ligands increased the catalytic activity which reached 36 kg_polymer mol^?1 h^?1, the highest value up to now reported for copper systems in methacrylic or acrylic monomer polymerization. These performances were ascribed to copper catalysts activated by MAO: without copper precursor, working in the presence of MAO and free salicylaldimine ligand, complete inactivity was ascertained. Copyright © 2010 Society of Chemical Industry     

Effect of N‐methylimidazole and 3,5‐dimethylpyrazole ligands on the polymerization of di(2,6‐dichlorophenolato) Cu(II)/Co(II) complexes in the solid state

The polymerization of 2,6‐dichlorophenol (DCPH) was achieved through the thermal decomposition of copper complexes of DCPH with N‐methylimidazole (NMIz) and 3,5‐dimethylpyrazole (DMPz) ligands. Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), mass spectrometry, ultraviolet–visible spectroscopy, diffuse reflectance spectroscopy, magnetic susceptibility balance, electron spin resonance, X‐ray analysis, and elemental analysis were used to characterize the complexes. The polymerization was achieved either in the solid state or in the melt. The structural analyses were performed with FTIR and NMR spectroscopy analyses. The glass‐transition temperatures were determined by DSC, and the intrinsic viscosities were determined by viscosimetry. The effects of the temperature and time on the conversion percentage and viscosity of the polymers were examined. Varying the decomposition temperature during a 3‐h scan showed that the DMPz complex of Cu decomposed at lower temperatures than the NMIz complex, whereas the NMIz complex yielded a higher conversion to the polymer. Complexes of DCPH with NMIz and DMPz ligands produced 1,2‐ and 1,4‐addition products, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3797–3805, 2004     

Polymerization of methyl methacrylate with Ni(acac)2–methylaluminoxane catalyst

Polymerization of methyl methacrylate (MMA) with nickel(II) acetylacetonate [Ni(acac)₂] in combination with methylaluminoxane (MAO) was investigated. Ni(acac)₂ was found to be an effective catalyst for the polymerization of MMA. From a kinetic study of the polymerization of MMA with the Ni(acac)₂–MAO catalyst, the overall activation energy was estimated to be 15 kJmol⁻¹. The polymerization rate (R_p) was expressed as follows: R_p = k [MMA]^1.0[Ni(acac)₂–MAO]^0.6 (the MAO/Ni mole ratio was kept constant). The mechanism for the polymerization of vinyl monomers with the Ni(acac)₂–MAO catalyst is discussed. © 2000 Society of Chemical Industry     

Influence of imine‐carbon substituent in 6‐bromo‐2‐iminopyridine‐based cobalt(II) complexes on 1,3‐butadiene polymerization

6‐Bromo‐2‐iminopyridine cobalt(II) complexes bearing different imine‐carbon substituents ( Co1 – Co7 ) were synthesized and subsequently employed for 1,3‐butadiene polymerization. All the complexes were identified using Fourier transform infrared spectra and elemental analysis, and complexes Co1 and Co3 were further characterized using single‐crystal X‐ray diffraction analysis, demonstrating they adopted distorted trigonal bipyramidal and tetrahedral geometries, respectively. Activated by methylaluminoxane, these complexes exhibited high cis‐1,4 selectivity, and the activity was highly dependent on the substituent at the imine‐carbon position of the ligand. Addition of PPh₃ to the polymerization systems could enhance the catalytic activity and simultaneously switched the selectivity from cis‐1,4 to cis‐1,2 manner. On the basis of the obtained results, a plausible mechanism involving the regulation of selectivity and activity is proposed. © 2019 Society of Chemical Industry     

Nickel(II) complexes bearing the bis(β‐ketoamino) ligand for the copolymerization of norbornene with a higher 1‐alkene

A novel bis(β‐ketoamino)Ni(II) complex catalyst, Ni{CF₃C(O)CHC[N(naphthyl)]CH₃}₂, was synthesized, and the structure was solved by a single‐crystal X‐ray refraction technique. The copolymerization of norbornene with higher 1‐alkene was carried out in toluene with catalytic systems based on nickel(II) complexes, Ni{RC(O)CHC[N(naphthyl)]CH₃}₂(R?CH₃, CF₃) and B(C₆F₅)₃, and high activity was exhibited by both catalytic systems. The effects of the catalyst structure and comonomer feed content on the polymerization activity and the incorporation rates were investigated. The reactivity ratios were determined to be r_1‐octene = 0.009 and r_norbornene = 13.461 by the Kelen–Tüdõs method for the Ni{CH₃C(O)CHC[N(naphthyl)]CH₃}₂/B(C₆F₅)₃ system. The achieved copolymers were confirmed to be vinyl‐addition copolymers through the analysis of ¹H‐NMR and ¹³C‐NMR. The thermogravimetric analysis results showed that the copolymers exhibited good thermal stability (decomposition temperature, T_dec > 400°C), and the glass‐transition temperature of the copolymers were observed between 215 and 275°C. The copolymers were confirmed to be noncrystalline by wide‐angle X‐ray diffraction analysis and showed good solubility in common organic solvents. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Stereospecific polymerization of styrene with novel half‐sandwich titanium complexes—RCpTi(o‐MeOPhCPh2O)Cl2/methylaluminoxane

Two new half‐sandwich titanocene catalysts for the stereospecific polymerization of styrene, RCpTi(o‐MeOPhCPh₂O)Cl₂ (R = H (1); R = Me (2)), were prepared by reaction of the corresponding RCpTiCl₃ complexes with o‐methoxyphenyldiphenylmethanol (o‐MeOPhCPh₂OH) in the presence of triethylamine. Upon activation with excess methylaluminoxane (MAO), they showed high activities and high thermal stabilities for the stereospecific polymerization of styrene. The influences of polymerization temperature, Al/Ti molar ratio, solvent (aliphatic or aromatic) and time on the activity and syndiotacticity of the styrene polymerization were investigated. Copyright © 2006 Society of Chemical Industry     

The reaction mechanism of diethyl‐2,3‐dicyano‐2,3‐di(p,m‐dimethoxylphenyl) succinate with styrene

The radical polymerization of styrene (ST) can be initiated by diethyl‐2,3‐dicyano‐2,3‐di(dimethoxyphenyl) succinate (ECPS). The reaction mechanism has been studied by means of UV, H¹‐NMR, product analysis, gel permeation chromatography, electronic spin resonance (ESR), and the conversion of monomer via time. These experimental results indicate that ECPS probably takes the place of complex with ST, and the complex interaction between ECPS and ST can take advantage of the dissociation of the C C bond. The complex interaction and thermal effect are the important factors causing the dissociation of C C bond. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1140–1145, 1999     

High cis‐1,4 polyisoprene or cis‐1,4/3,4 binary polyisoprene synthesized using 2‐(benzimidazolyl)‐6‐(1‐(arylimino)ethyl)pyridine cobalt(II) dichlorides

Polyisoprene (PI) with a high content of cis‐1,4 (up to 95%) or cis‐1,4/3,4 binary structures was synthesized using a cobalt system in toluene. The cobalt system, which exhibited high activities (up to 3.50 × 10⁶ g PI (mol Co)^?1 h^?1), contained a series of 2‐(benzimidazolyl)‐6‐(1‐(arylimino)ethyl)pyridine cobalt(II) dichlorides activated with ethylaluminium sesquichloride. The nature of the ligands and the reaction conditions significantly affected both the catalytic performance of the cobalt complexes as well as the structures of the resultant PI. The stereospecific polymerization of isoprene could be tuned via changing either the co‐catalyst or solvent: for example, increased content of 3,4 PI (up to 36.6%) was achievable in heptane in the presence of diethylaluminium chloride. Sequence distribution analysis by ¹³C NMR spectroscopy indicated that most 3,4 units occurred randomly in the PI chains. © 2013 Society of Chemical Industry     

Neutral Pd(II) and Ni(II) Acetylide Catalysts for the Polymerization of Methyl Methacrylate

Homogenous polymerization of methyl methacrylate using Pd(II)- and Ni(II)-based acetylide complexes as initiators has been investigated. M(PR'₃)₂(CCR)₂ (M=Pd, Ni; R'=PPh₃, Pn-Bu₃; R=Ph, CH₂OH, CH₂OOCCH₃, CH₂OOCPh, CH₂OOCPhOH-o) were found to be a novel type of effective initiators for the polymerization of methyl methacrylate. Among them, Pd(C CPh)₂(PPh₃)₂ (PPP) shows the highest activity in the MMA polymerization and the PMMA obtained is a syndiotactic polymer with high number-average molecular weight (M _n) of 14.1 × 10⁴. Some features and kinetic behavior of MMA polymerization initiated by PPP were studied in detail. The polymerization reaction is first-order with respect to both [PPP] and [MMA]. Radical polymerization mechanism is proposed.     

Polymerization of 1,3‐butadiene with VO(P204)2 activated by methylaluminoxane,purified methylaluminoxane,and trimethylaluminum

The effect of different aluminum‐based cocatalysts (MAO, pMAO, and TMA) on butadiene (Bd) polymerization catalyzed by VO(P204)2 was investigated. The bimodal dependence of the polymer yield on the [MAO]/[V] molar ratio was revealed, and an highest polymer yield was achieved at a rather low [MAO]/[V] molar ratio ([MAO]/[V] = 13). The microstructures of the resulting poly(Bd)s were also significantly influenced by the ratio. In the TMA or pMAO system, the polymer yields were also very sensitive to the [Al]/[V] molar ratio. However, the microstructures of the resulting poly(Bd)s were almost independent of the ratio. In relation to the microstructures of poly(Bd)s obtained by the MAO and TMA systems at various temperatures, the 1,2‐unit contents were found to be the most abundant microstructure for both systems. In the pMAO system, the trans‐1,4‐units were the most abundant. The results of the additions of Lewis bases (THF and TPP) into Bd polyerization system comfirmed the existing of the two types of the reactions of VO(P₂₀₄)₂‐MAO catalyst and had the polymerization process controlled to some extent. The different thermal behaviors of these catalytic systems also show that multiple types of active centers were formed during the reaction between VO(P₂₀₄)₂ and MAO. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Styrene/substituted styrene copolymerization by Ph2Zn–metallocene–MAO systems: homo‐ and copolymerization of p‐methoxystyrene with styrene

BACKGROUND: The present work is part of a general study regarding the homo‐ and copolymerization of styrene using diphenylzinc–additive initiator systems, with the aim of improving the properties of commercial atactic polystyrene. The study is focused on syndiotactic polystyrene and/or copolymers of styrene (S) with substituted styrene, styrene derivatives or various α‐olefins. This research has been ongoing over the last 15 years. RESULTS: The reported experiments show that binary metallocene–methylaluminoxane (MAO) and ternary Ph₂Zn–metallocene–MAO, depending on the metallocene employed, are capable of inducing both homo‐ and copolymerization of styrene and p‐methoxystyrene (p‐MeOS). The results indicate that for a styrene/p‐MeOS mole ratio with p‐MeOS > 25% the product obtained has only a minor incorporation of styrene units. The efficiency of the metallocenes studied follows the order bis(n‐butylcyclopentadienyl)titanium dichloride ((n‐BuCp)₂TiCl₂) > indenyltitanium trichloride (IndTiCl₃) > Cp₂TiCl₂. CONCLUSION: Metallocenes (n‐BuCp)₂TiCl₂, Cp₂TiCl₂ and IndTiCl₃ in binary systems combined with MAO, as well as in ternary systems combined with Ph₂Zn and MAO, induce the homopolymerization of p‐MeOS and its copolymerization with styrene. The styrene/p‐MeOS copolymer obtained was enriched in p‐MeOS with respect to the initial feed, in agreement with the I+ inductive effect of the methoxy group in the para position of styrene. As already reported, the role of Ph₂Zn was nullified by its complexation with the p‐MeOS comonomer. Copyright © 2008 Society of Chemical Industry     

Neutral Pd(II) and Ni(II) Acetylide Initiators for Polymerization of (Dimethylamino)ethyl Methacrylate

A series of air-stable, late transition, metal-based initiators with the structures ML₂(CCR)₂ (M=Pd and Ni; L=PPh₃ and Pn-Bu₃; R=Ph and CH₂OH) for the polymerization of (dimethylamino)ethyl methylate (DMAEMA) were developed. Transition metal, phosphine, alkynyl, as well as solvents exhibited significant influence on the polymerization. Among them, Pd(CCPh)₂(PPh₃)₂ (PPP) shows the highest activity in CHCl₃ for DMAEMA polymerization. The PDMAEMA obtained is a syndiotactic polymer with high number-average molecular weight (M_n) of 20.2 × 10⁴. A free radical polymerization mechanism with some ATRP characteristics was proposed for the present polymerization.     

Polymerisation of ethylene catalysed by mono‐imine‐2,6‐diacetylpyridine iron/methylaluminoxane (MAO) catalyst system: effect of the ligand on polymer microstructure

The complex, {1‐{6‐[(2,6‐diisopropylphenyl)‐ethaneimidoyl]‐2‐pyridinyl}‐1‐ethanone}iron(II) dichloride ( 2 ), has been synthesised and characterised. Treatment of complex 2 with methylaluminoxane resulted in a very active catalytic system for the preparation of polyethylene (PE). The system shows activities in the order of magnitude 10⁷ g (PE) mol^?1(Fe) h^?1 bar^?1. Characterisation by ¹³C NMR indicated that branched PE was obtained and that experimental conditions affect polymer microstructure. PE produced contained six to eight branches per 100 carbons. © 2002 Society of Chemical Industry