Fracture behavior of thermoplastic polyolefin/clay nanocomposites

A thermoplastic polyolefin (TPO) containing 70 wt % styrene–ethylene–butadiene‐styrene‐g‐maleic anhydride and 30 wt % polypropylene and its nanocomposites reinforced with 0.3–1.5 wt % organoclay were prepared by melt mixing followed by injection molding. The mechanical and fracture behaviors of the TPO/clay nanocomposites were investigated. The essential work of fracture (EWF) approach was used to evaluate the tensile fracture behavior of the nanocomposites toughened with elastomer. Tensile tests showed that the stiffness and tensile strength of TPO was enhanced by the addition of low loading levels of organically modified montmorillonite. EWF measurements revealed that the fracture toughness of the TPO/clay nanocomposites increased with increasing clay content. The organoclay toughened the TPO matrix of the nanocomposites effectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical and oxygen barrier properties of organoclay-polyethylene nanocomposite films

An organically modified montmorillonite was compounded with ethylene vinyl acetate copolymer (EVA), low density polyethylene (LDPE), and high density polyethylene (HDPE) in a twin-screw extruder. The resulting organoclay-polyethylene nanocomposites were then blown into films. Tensile properties and oxygen permeability of these nanocomposite films were investigated to understand the effects of organoclay on different types of polyethylene. It was found that the clay enhancing effects are function of the matrix. The mechanical and oxygen barrier properties of clay/EVA systems increased with clay loading. Both the tensile modulus and oxygen barrier of EVA doubled at 5 wt% clay. Maleic anhydride grafted polyethylene (MAPE) usually is used as a compatibilizer for LDPE and HDPE-based nanocomposites. However, the MAPEs were found to weaken the oxygen barrier of the PEs, especially for HDPE. This is believed to be a result of less compactness caused by the large side groups and the increase in polarity of the MAPEs. Incorporating 5 wt% clay improves the oxygen barrier by 30% and the tensile modulus by 37% for the LDPE/MAPE system. Incorporation of clay does not enhance the properties of the HDPE-based systems, likely due to large domain structure and poor bonding. Halpin–Tsai equation and the tortuous path equation were used to model the tensile modulus and oxygen permeability of the clay/EVA nanocomposite films. POLYM. ENG. SCI., 47:1101–1107, 2007. © 2007 Society of Plastics Engineers     

Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal,mechanical, and barrier properties of polyethylene/surlyn/organoclay nanocomposites blown films prepared by different mixing methods

(Low‐density polyethylene) (LDPE)/clay nanocomposites were prepared by melt blending in a twin‐screw extruder by using different mixing methods. Zinc‐neutralized carboxylate ionomer was used as a compatibilizer. Blown films of the nanocomposites were then prepared. The effect of mixing method on the clay dispersion and properties of the nanocomposites was evaluated by wide‐angle X‐ray diffraction analysis, mechanical properties, thermal properties, and barrier properties. The structure and properties of nanocomposites containing different amounts of nanoclay prepared by selected mixing techniques were also investigated. It was found that melt compounding of Surlyn/clay masterbatch with pure LDPE and Surlyn (two‐step‐a method) results in better dispersion and intercalation of the nanofillers than melt mixing of LDPE/Surlyn/clay masterbatch with pure LDPE and surlyn (two‐step‐b method) and direct mixing of LDPE with clay. The films containing ionomer have good barrier properties. A wide‐angle X‐ray diffraction pattern indicates that intercalation of polymer chains into the clay galleries decreases by increasing the clay content. Barrier properties and tensile modulus of the films were improved by increasing the clay content. In addition, tensile strength increased in the machine direction, but it decreased in the transverse direction by increasing the clay content. DSC results showed that increasing the clay content does not show significant change in the melting and crystallization temperatures. The results of thermogravimetric analysis showed that the thermal stability of the nanocomposites decreased by increasing the clay content more than 1 wt%. J. VINYL ADDIT. TECHNOL., 21:60–69, 2015. © 2014 Society of Plastics Engineers     

Preparation of PE nanocomposites using pristine nano clay via alkyl ammonium solution injection in a twin‐screw extruder

In this study, saline water was used as a preintercalating agent for pristine clay surface to assist clay dispersion in one‐step melt state process. The solution contains dodecyl trimethyl ammonium chloride salt in distilled water and was injected into the twin‐screw extruder using a high pressure dosing pump. To investigate the effect of dissolution of alkyl salt on clay dispersion, two samples with the same compositions were prepared through both salt solution and pure water injection which was compared with organo‐modified prepared sample. The resultant compounds were characterized using x‐ray diffraction (XRD), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and dynamic rheological measurements (RMS). Tensile and notched‐Izod impact properties of the samples were measured as well. The XRD results showed no peak for the sample containing 2 wt % pristine clay, prepared via injection of salt solution representing exfoliated microstructure. In addition, TEM images showed proper dispersion and distribution of clay platelets in the matrix. Furthermore, RMS results showed that the slop of the storage modulus has been declined and for the sample using saline, the variation was prominent as a result of network structure formation. Tensile results also showed an increase of tensile modulus in the range of about 22% for the sample containing 2 wt % clay. Izod impact strength in the sample prepared via injection of salt solution showed fracture energy comparable to neat polyethylene. Additionally, the crystallization data in terms of degree of crystallinity, melting, and crystallization temperatures of samples represented no noticeable change compared to neat polyethylene. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of carbon nanofibers on crystalline structures and properties of ultrahigh molecular weight polyethylene blend fabricated using twin‐screw extrusion

Melt mixing in an extruder with polymers is an effective approach for forming nanocomposites, allowing mass production applications. The intent of this study is to investigate carbon nanofiber composites with ultrahigh molecular weight polyethylene (UHMWPE) matrix using the twin‐screw extruder. To decrease the high viscosity of UHMWPE, a low density polyethylene (LDPE) was added into the UHMWPE. The effects of carbon nanofibers (CNFs) on the crystalline structures and properties of the nanocomposites were analyzed. The differential scanning calorimetry (DSC) and X‐ray diffraction (XRD) measurements showed the addition of CNFs decreases the degree of crystallinity, but does not impart significant effects on the crystalline structure of the UHMWPE/LDPE blend. Tensile test results showed that the nanocomposite with loading of 3 wt % CNFs had an increase of 38% in tensile strength and 15% in modulus. The thermal stability and thermal conductivity of UHMWPE/LDPE blends were also enhanced by the addition of CNFs. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of polypropylene/clay nanocomposites

Polypropylene/clay (PP/clay) nanocomposites were synthesized via intercalative polymerization. The nanostructure of the composites was investigated by wide‐angle X‐ray diffractometry (WAXD) and transmission electron microscopy (TEM). The WAXD patterns of the PP/clay nanocomposites indicated that the characteristic diffraction peak of the clay disappeared. The TEM image showed the clay was exfoliated into nanometer size and dispersed uniformly in the PP matrix. The composites exhibited much higher storage modulus compared to that of pure PP. At temperatures higher than T_g, the storage modulus of the PP/clay nanocomposites with 8.1 wt % clay content increased three times that of the pure PP. Additionally, the thermal stability of the nanocomposites significantly increased. The maximum decomposition temperature was increased by 44°C with the introduction of about 10 wt % clay. The heat‐distortion temperatures (HDTs) of the nanocomposites also increased. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3611–3617, 2001     

Thermal and mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites over a wide range of filler loading

BACKGROUND: Poly(methyl methacrylate) (PMMA)–organoclay nanocomposites with octadecylammonium ion‐modified montmorillonite, prepared via melt processing, over a wide range of filler loading (2–16 wt%) were investigated in detail. These hybrids were characterized for their dispersion structure, and thermal and mechanical properties, such as tensile modulus (E), break stress (σ_brk), percent break strain (ε_brk) and ductility (J), using wide‐angle X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and tensile and impact tests. RESULTS: Intercalated nanocomposites were formed even in the presence of 16 wt% clay (high loading) in PMMA matrix. PMMA intercalated into the galleries of the organically modified clay, with a change in d‐spacing in the range 11–16 Å. TGA results showed improved thermal stability of the nanocomposites. The glass transition temperature (T_g) of the nanocomposites, from DSC measurements, was 2–3 °C higher than that of PMMA. The ultimate tensile strength and impact strength decreased with increasing clay fraction. Tensile modulus for the nanocomposites increased by a significant amount (113%) at the highest level of clay fraction (16 wt%) studied. CONCLUSION: We show for the first time the formation of intercalated PMMA nanocomposites with alkylammonium‐modified clays at high clay loadings (>15 wt%). Tensile modulus increases linearly with clay fraction, and the enhancement in modulus is significant. A linear correlation between tensile strength and strain‐at‐break is shown. Thermal properties are not affected appreciably. Organoclay can be dispersed well even at high clay fractions to form nanocomposites with superior bulk properties of practical interest. Copyright © 2007 Society of Chemical Industry     

Synthesis and characterization of polyethylene‐octene elastomer/clay/biodegradable starch nanocomposites

The aim of this work is the production of new nanocomposites from metallocene polyethylene‐octene elastomer (POE), montmorillonite and biodegradable starch by means of a melt blending method. Characterizations of clay, modified clay, POE, POE‐g‐AA, and the hybrids produced from polymer, clay, and/or starch were performed by X‐ray diffraction (XRD) spectroscopy, Fourier transform infrared (FTIR) spectrophotometer, differential scanning calorimetry (DSC), thermogravimetry analyzer (TGA), scanning electron microscope (SEM), and Instron mechanical tester. As to the results, organophilic clay can be well dispersed into acrylic acid grafted polyethylene‐octene elastomer (POE‐g‐AA) in nanoscale sizes since cetyl pyridium chloride is partially compatible with POE‐g‐AA and allows POE‐g‐AA chains to intercalate into clay layers. Based on consideration of thermal and mechanical properties, it is also found that 12 wt % of clay content is optimal for preparation of POE‐g‐AA/clay nanocomposites. The new partly biodegradable POE‐g‐AA/clay/starch hybrid could obviously improve the elongation and the tensile strength at break of the POE‐g‐AA/starch hybrid since the former can give the smaller starch phase size and nanoscale dispersion of silicate layers in the polymer matrix. The nanocomposites produced from our laboratory can provide a stable tensile strength at break when the starch content is up to 40 wt %. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 397–404, 2005     

Structure and dynamics of polyethylene/clay films

The relationships between structure and rheology of polyethylene/clay hybrid composite blown films were investigated through rheological tests both in shear and elongational flow. Two polymer matrices (low density polyethylene, LDPE and linear low density polyethylene, LLDPE) with different relaxation kinetics were used. Independently from the matrix, morphological analyses (TEM, XRD, and SEM) indicate that the hybrid structures are similarly constituted of delaminated platelets or tactoids having a relevant degree of orientation along the draw direction. This strongly affects the rheological behavior of materials. However, despite the similarities emerged from morphological analyses, both shear (steady shear and oscillatory) and elongation measurements show a negligible effect upon the rheology of LDPE‐based nanohybrids. Conversely, relevant increases of shear viscosity, dynamic moduli and melt strength of LLDPE‐based nanohybrids have been detected. The effects of homopolymer relaxation kinetics have been investigated by means of stress relaxation tests. The results obtained seem to be consistent with the existence of a roughly bimodal population of dynamical species: a matrix component behaving like the homopolymer, and a fraction interacting with the filler, whose rheological behavior is controlled by the particles and their interactions with the polymer. Mechanical properties of hybrid films were also investigated. Differently from what happens in the melt state, the solid‐state properties mainly depend on the filler amount. The relative increases of tensile modulus and melt strength are of the same order of magnitude for both the matrices used, indirectly confirming the similarities in hybrids structures. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4749–4758, 2006     

Enhancement of the thermal stability,mechanical properties and morphologies of recycled PVC/clay nanocomposites

Summary Recycled PVC/clay nanocomposites were prepared by melt mixing of recycled PVCs and modified clays. Characterization of the nanostructure of the nanocomposites was carried out using wide angle X-ray diffraction (WAXD) and transmission electron microscopy(TEM). In case of 10wt.%, the characteristic peak of modified clay was perfectly disappeared, because of aids of plasticizers as co-intercalator. Thermal stability was evaluated from the thermal decomposition behaviors and linear dimension changes by TGA and TMA system. Coefficients of thermal expansion of the nanocomposites were also observed from TMA analysis. Dynamic mechanical properties were evaluated using DMA system. The thermal and mechanical properties of the nanocomposites were improved simultaneously for varied clay loadings, 1,3,5,10wt.%, compared to recycled PVC. Especially, the storage modulus of the nanocomposites with 10wt.% clay loading was increased 11 times compared to that of recycled PVC.     

Effects of clay dispersion on the foam morphology of LDPE/clay nanocomposites

Intercalated and exfoliated low‐density polyethylene (LDPE)/clay nanocomposites were prepared by melt blending with and without a maleated polyethylene (PE‐g‐MAn) as the coupling agent. Their morphology was examined and confirmed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of clay content and dispersion on the cell morphology of nanocomposite foams during extrusion foaming process were also thoroughly investigated, especially with a small amount of clay of 0.05–1.0 wt%. This research shows the optimum clay content for achieving microcellular PE/clay nanocomposite foams blown with supercritical CO₂. It is found that < 0.1 wt% of clay addition can produce the microcellular foam structure with a cell density of > 10⁹ cells/cm³ and a cell size of ～ 5 μm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2129–2134, 2007     

New poly(phenylene oxide)/polystyrene blend nanocomposites with clay: Intercalation,thermal and mechanical properties

We present the first study and results on the preparation and characterization of montmorillonite clay filler based polymer blend nanocomposites of the miscible poly(phenylene oxide)/polystyrene blend. Intercalated nanocomposites, prepared by a melt‐processing method with 2–6 wt % commercially available organically modified sodium montmorillonite, have been characterized with wide‐angle X‐ray diffraction, transmission electron microscopy analysis, thermal analysis (thermogravimetric analysis and differential scanning calorimetry), and mechanical tensile tests. We show that nanocomposites can be successfully prepared in a batch mixer at temperatures much below the conditions conventionally used for this blend without organic degradation. Thermal stability is enhanced by nanoscale hybrid formation. The level of intercalation (change in the d‐spacing) does not change with the clay loading. Better dispersion of clay in the blend matrix has been observed at a low level of clay content. The nanocomposites show improved tensile modulus (by 31%) in comparison to the blend, whereas the tensile strength (stress at break) and elongation decrease in the presence of the filler with an increase in the clay loading. The Halpin–Tsai model is able to predict the modulus of the nanocomposites in very good agreement with the experimental data. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Oxidative degradations of oxodegradable LDPE enhanced with thermoplastic pea starch: Thermo‐mechanical properties,morphology, and UV‐ageing studies

The abiotic UV‐degradation behavior of oxodegradable LDPE was investigated in the presence of thermoplastic pea starch (TPPS) in this study. Oxodegradable LDPE was first melt‐blended with thermoplastic pea starch (TPPS) using an internal mixing chamber to enhance the abiotic oxidative degradation of oxodegradable LDPE. Because of their different affinity, maleated polyethylene was added as compatibilizer. Tensile properties, thermal properties, and morphology of resulting melt‐blends were determined at different content in TPPS. High content in TPPS (40 wt %) could be readily added to oxodegradable LDPE without affecting the tensile properties of resulting melt‐blends. UV‐ageing studies on compatibilized TPPS/oxodegradable LDPE melt‐blends were carried out by Attenuated Total Reflectance infrared spectroscopy (ATR‐FTIR), Dynamic Thermomechanical Analyses (DMTA) and Differential Scanning Calorimetry (DSC) under abiotic conditions. These results suggested a synergistic effect on the UV‐ageing of TPPS‐based melt‐blends provided by both components during the first stage of UV‐irradiation. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Supercritical carbon dioxide (scCO2) dispersion of poly(ethylene terephthalate)/clay nanocomposites: Structural,mechanical, thermal,and barrier properties

Dispersed poly(ethylene terephthalate) (PET)/clay nanocomposites can lead to materials with superior barrier and mechanical properties. PET/clay nanocomposites were prepared by melting extrusion of PET with as‐received or supercritical carbon dioxide (scCO₂) predispersed Cloisite^® 30B (30B). The predispersion of 30B was assessed by WAXD, SEM, and TGA, and results indicated that scCO₂ processing could predisperse 30B and the surface modification of the clay was preserved after processing. The structure of PET/30B nanocomposites was investigated by WAXD and TEM confirming that PET has penetrated into the clays inter‐galleries and the predispersed clays lead to improved interfacial interaction and homogenous clay dispersion. Both tensile strength and Young's modulus were improved by 12.1% and 24.9% respectively, as incorporating of 3 wt % of scCO₂ processed clay. Differential scanning calorimetry (DSC) results indicated that clay particles served as nucleation agent could increase the crystallinity whereas had no impact on melting process. In addition, with the addition of 1 wt % of predispersed clay, a significant reduction of oxygen permeation (～33%) was achieved at 23 °C and the maximum reduction (44%) was achieved by adding 3 wt % processed clay. Moreover, we confirmed the effect of temperature on the permeation of PET/30B nanocomposites depended both on the Arrhenius behavior of the organic phases and tortuous path effects, where improved clay dispersion resulted in a higher effective activation energy. Moreover, the transparency of PET matrix was preserved for all nanocomposites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44779.     

Effect of PEgMA/amine silane compatibilizer on clay dispersion of polyethylene-clay nanocomposites

The compatibilization effects provided by an amine silane modified polyethylene (PEgAS) versus those by a maleated polyethylene (PEgMA), for forming PE–clay based nanocomposites, were studied. PEgAS was prepared by condensation reaction between PEgMA and g-(aminopropyl) triethoxy silane (APTS). It had the triethoxy-silane functionality on one end and was solution mixed with an organomodified clay (Cloisite 20A) to promote the reaction of the silane groups with the hydroxyl groups on the surface of the clay. The obtained masterbatches were then compounded with PE to obtain PE–clay nanocomposites by melt blending in a twin screw extruder, using different compatibilizers and clay contents. FTIR, XRD, STEM, and Instron were used to characterize the structural, morphological, and mechanical properties of the nanocomposites. Results showed that the PEgAS formed more exfoliated–intercalated morphology and better mechanical properties, especially in modulus and tensile strength as compared with PEgMA composites and neat PE. The Young modulus was 35% higher, and the tensile strength was 18% higher with PEgAS composites.     

The influence of processing route on the structuring and properties of high‐density polyethylene (HDPE)/clay nanocomposites

The effect of different processing routes on structure and properties of high‐density polyethylene (HDPE)‐clay nanocomposites was assessed. Different compatibilizer/clay ratios (α) were also studied to determine if interactions exist between processing route and polymer‐clay compatibility. HDPE/HDPE‐g‐MA/clay with α values of 1 to 4 were melt compounded (twin screw extrusion), and then processed via three routes: compression moulding, compression moulding followed by biaxial stretching or blown film extrusion. The structure was examined using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and oxygen barrier properties were determined. It was found that biaxial extensional forming produced the best enhancement in properties. An interaction between processing route and polymer‐clay compatibility is evident. Halpin‐Tsai (H‐T) model was employed to predict relative modulus values. It showed good agreement with the experimental data. For biaxial extension at α = 4.0, the experimental relative modulus is greater than the predicted value. This may indicate the existence of a “nano” effect at the polymer‐clay interface. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Morphology and properties of PVC/clay nanocomposites via in situ emulsion polymerization

PVC/Na⁺–montmorillonite (MMT) nanocomposites were prepared via a simple technique of emulsion polymerization at several different MMT clay concentrations. X‐ray diffraction and transmission electron microscopy studies revealed the formation of a mixture of intercalated and exfoliated nanostructure. Tensile testing results showed that the tensile modulus of the nanocomposites increased with the addition of clay, while the tensile strength decreased little. The notched impact strength of the nanocomposites was also improved. For systems containing clay in the range of 2.1 to 3.5 wt %, the impact strength was almost two times as large as that of pure PVC. However, those mechanical properties began to decrease with the continuously increasing amount of clay. The fracture surface of pure PVC and the nanocomposites was observed by scanning electron microscope. Thermal properties of the nanocomposites were found to increase as a result of clay incorporation. The glass transition temperatures of the PVC/clay nanocomposites were nearly identical to that of pure PVC. The Vicat softening points exhibited a progressively increasing trend with the clay content added. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 277–286, 2004     

Preparation and characterization of polymer/organosilicate nanocomposites based on unmodified LDPE

Low‐density polyethylene (LDPE)/silicate nanocomposites were prepared by the melt compounding and solution blend methods using unmodified LDPE polymer and layered silicates with different aspect ratio. X‐ray diffraction (XRD) analysis performed on composites obtained by dispersing the organosilicates in molten LDPE evidenced an exfoliated or partially exfoliated structure for the low aspect ratio silicate (laponite) in contrast to the high aspect ratio silicate (montmorillonite), which led to the formation of intercalated nanocomposites. With regard to the preparation method, the melt compounding method was more effective in forming exfoliated/highly intercalated LDPE nanocomposites compared with the solution blend method (using CCl₄ as a solvent). A gradual increase in crystallization temperatures (T_c) with increasing laponite content for LDPE‐organolaponite nanocomposites was revealed by differential scanning calorimetry (DSC) measurements. Thermogravimetric analysis and tensile measurements results indicated that thermal stability and elastic modulus increment were more prevalent for nanocomposites prepared using organomontmorillonite as filler. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of clay dispersion and content on the rheological,mechanical properties,and flame retardance of HDPE/clay nanocomposites

Full exfoliation of clay/high density polyethylene (HDPE) nanocomposites was successfully achieved with the aid of maleated HDPE (PE‐g‐MAn), by melt blending in a twin‐screw extruder employing a long residence time configuration. The morphology of the composites was determined using wide‐angle X‐ray diffraction and transmission electron microscopy. The effects of clay content and state of clay dispersion on the rheological, tensile properties, and flame retardancy of nanocomposites containing very small amounts of clay, in the range of 0.05–1.0 wt %, were investigated in this study. It was demonstrated that achieving a higher degree of exfoliation for nanosized clay particles is key to enhancing the rheological, mechanical, and flame retarding properties even when small amounts of clay (less than 1%) are used. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007