Synthesis and characterization of α‐methylstilbene‐ and azobenzene‐based thermotropic liquid crystalline polymers

A series of combined liquid crystalline poly(bis‐4,4′‐oxy‐α‐methylstilbene‐4‐substituted (X) phenylazo‐4′‐phenyloxydecylphosphate ester)s bearing photoreactive mesogenic units were synthesized. FTIR and ¹H NMR spectroscopy confirmed the structures of these polymers. The inherent viscosities of the polymers were found to be in the range 0.45–0.65 dL g^?1. Polarizing optical microscopy (POM) exhibited birefringent liquid crystalline melt properties. The thermal properties of all of the polymers were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The photochemical properties of these polymers were studied by UV‐visible and fluorescence spectroscopy. The influence of the photoinduced E–Z (trans–cis) isomerization of the various terminal substituents of the side‐chain azobenzenes was investigated. The kinetics of the photoisomerization process reveal the switching times for the conversion between the trans‐ and cis‐ forms of the azobenzene units. The photo‐optical properties of these polymers exhibited layered smectic phases and showed good photoinduced properties in their mesomorphic states. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of a new family of photoactive liquid crystalline polyesters based on α‐methylstilbene

A liquid crystal polyester and two liquid crystal copolyesters containing α‐methylstilbene moieties and aliphatic or aromatic spacers in the backbone were synthesized in good yields, with the aim of using them for photosensitive microcapsule preparation. The synthesized polymers were fully characterized with respect to thermal stability, type of mesophase, molecular weight and E–Z photoisomerization. Combination of monomers with different structures allowed adjustment of the polymer characteristics such as degree of crystallinity and glass transition temperature, as verified using X‐ray diffraction, polarized optical microscopy and differential scanning calorimetry. Quantitative ¹H NMR and UV‐visible experiments were performed in order to investigate E–Z photoisomerization after photoirradiation at 364 nm. Finally, a membrane based on one of these polymers was prepared and it was found that its wettability increased on photoirradiation. © 2013 Society of Chemical Industry     

Silicone‐based cholesteric liquid crystalline polymers: Effect of crosslinking agent on phase transition behavior

Silicone‐based cholesteric liquid crystalline polymers (ChLCP) were fabricated with variable clearing temperatures as controlled by their chemical compositions. The chemical structures of the mesogenic monomers and ChLCP were confirmed by FTIR and ¹H‐NMR spectroscopy. The mesogenic properties and phase behavior were investigated by differential scanning calorimetry, polarizing optical microscopy, and X‐ray diffraction measurements. The experimental results demonstrated that the glass transition temperatures and the clearing points of the liquid crystalline polymers decreased with increasing proportion of mesogenic crosslinking agent up to 12.50 mol % (LCP‐3), and at higher proportion of crosslinking agent, the clearing points disappeared, indicating that the network chains have less chance to orient themselves. Thermogravimetric analysis showed that the LCP‐3 was the most stable up to 230°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of a novel liquid crystalline star‐shaped polymer based on α‐CD core via ATRP

Well‐defined side‐chain liquid crystalline star‐shaped polymers were synthesized with a combination of the “core‐first” method and atom transfer radical polymerization (ATRP). Firstly, the functionalized macroinitiator based on the α‐Cyclodextrins (α‐CD) bearing functional bromide groups was synthesized, confirmed by ¹H‐NMR, MALDI‐TOF, and FTIR analysis. Secondly, the side‐chain liquid crystalline arms poly[6‐(4‐methoxy‐4‐oxy‐azobenzene) hexyl methacrylate] (PMMAzo) were prepared by ATRP. The characterization of the star polymers were performed with ¹H‐NMR, gel permeation chromatography (GPC), differential scanning calorimetry (DSC) and thermal polarized optical microscopy (POM). It was found that the liquid crystalline behavior of the star polymer α‐CD‐PMMAzo_n was similar to that of the linear homopolymer. The phase‐transition temperatures from the smectic to nematic phase and from the nematic to isotropic phase increased as the molecular weight increased for most of these samples. All star‐shaped polymers show photoresponsive isomerization under the irradiation with Ultraviolet light. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of novel acrylate‐based liquid crystalline polymers and the photoinduced alignment behavior of their films

Two acrylate monomers containing both mesogenic biphenyl group and photoreactive cinnamoyl group as well as different length of flexible spacers (i.e., n‐[4′‐(n‐cinnamoyloxyalkoxy)biphenyl‐4‐yloxy]alkyl acrylate, n = 4 (A4OO4C) and 6 (A6OO6C)) were synthesized for the first time. Their corresponding polymers (i.e., PA4OO4C and PA6OO6C) were obtained by free radical polymerization using AIBN as an initiator. The monomer A4OO4C showed smectic liquid crystalline phase and a clear fan texture was observed under optical polarizing microscope. However, no liquid crystalline phase was found for A6OO6C. In contrast, PA4OO4C showed no liquid crystalline phase while PA6OO6C showed a clear nematic schlieren texture during the cooling process. The optical polarized microscope of E5 cast on the top of the polymer film also showed the alignment. Furthermore, the irradiation of the polymer films by LP‐UV light led to the cycloaddition of the cinnamoyl groups, resulting in the simultaneous alignment of the biphenyl groups. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4565–4572, 2006     

Photoisomerization behavior of bisbenzylidene and 1,3,4‐oxadiazole‐based liquid crystalline polyesters

Photoisomerization behavior of bisbenzylideneacetone/cycloheptanone and 1,3,4‐oxadiazole containing nematic liquid crystalline polyesters under UV irradiation was investigated. Solubility, carbonyl group absorption band in FTIR, optical microscopy observation, as well as DSC analysis through existence of liquid crystallinity after irradiation were proved this phenomenon. Fluorescence spectra revealed blue‐emission maxima with Stokes shift in the range of 46–49 nm. Band gap energy calculated from absorption spectra are in the range of 3.18–3.41 eV. Structure–property relationships were probed by correlating the spacer length with development of mesophase formation, thermal, and optical properties. Optical property of polymers disclosed photoisomerization processes. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and thermal properties of polythioether‐based liquid‐crystalline polymers containing azobenzene in the side chain

BACKGROUND: Owing to the unusual structural rearrangement of polychloromethylthiirane (PCMT) at room temperature, it has not been used as the main‐chain backbone of side‐chain liquid‐crystalline polymers (SLCPs). However, it has been observed that PCMT has a relatively stable and clear structure under special conditions. Therefore, we attempted to synthesize SLCPs using PCMT as main‐chain backbone and investigated their thermal behavior. RESULTS: New polymers, poly[1‐({(4‐methoxyazobenzene‐4′‐oxy)alkyl}thio)‐2,3‐epithiopropane], in which the number of methylene units in the alkyl group is 4, 5 or 6, were prepared by means of reactions of corresponding (4‐methoxyazobenzene‐4′‐oxy)alkylthiols with PCMT. The structures of these compounds were confirmed using elemental analysis and ¹H NMR spectroscopy. The substitution ratios of the copolymers with 4, 5 and 6 methylene units in the alkyl group were 56, 75 and 80%, respectively. Differential scanning calorimetry measurements and polarized optical microscopy observations showed that the resulting copolymers exhibited thermotropic liquid‐crystalline mesomorphism with nematic phase except for the copolymer with a 56% substitution ratio. The decomposition temperature of all the synthesized copolymers was near 195 °C. CONCLUSION: This investigation has demonstrated that PCMT polymerized for 8 h has the ability to act as a suitable main‐chain backbone for SLCPs. Moreover, SLCPs could be obtained only by the reaction of PCMT with thiolate salt containing mesogenic groups. The substitution ratios increased with increasing number of methylene groups in the spacer. Copyright © 2009 Society of Chemical Industry     

Preparation and properties of Mahua oil‐based liquid crystalline pentalkyds

Medium oil length Mahua oil‐based pentalkyds are prepared with varying degree of excess hydroxyl. These alkyds are subsequently converted into liquid crystalline form by copolymerizing with p‐hydroxy benzoic acid (p‐HBA). Esterification is facilitated by dicyclohexyl carbodiimide (DCC). Graft efficiencies of copolymers are calculated and reported. Characterization of grafted alkyds is carried out using IR, DSC, and polarizing microscope techniques. A sharp melting point indicates liquid crystalline characteristic of p‐HBA grafted alkyds. DSC and polarizing microscope study results further substantiated the observation. Mechanical film properties of LC resins viz., hardness, impact resistance, and adhesion are also reported and compared with the amorphous counterparts. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies on the mesomorphic properties of ferrocenylene‐based organophosphorous liquid‐crystalline polymers containing phenyl and biphenyl pendant units

The synthesis, mesomorphic character, and effect of spacers in ferrocene‐containing main‐chain liquid‐crystalline polymers are reported in this article. Two different monomers containing ferrocene and phenyl/biphenyl phosphate groups possessing even numbers of spacers from 2 to 10 were prepared and polymerized by polycondensation at room temperature. All the polymers gave birefringent melt except one. The identification of the mesophase was transparent with an increase in spacers. The effect of substitution in the side chain with regard to bulkiness and spacers were studied with thermogravimetric analysis and differential scanning calorimetry. The results reveal that the thermal stability of the polymers increased with the increasing bulkiness of the side chain and decreased with increasing spacer length. The incorporation of the phosphorous moiety also had a considerable effect on the glass‐transition temperature. Char yield of the polymer decreased with increasing methylene chain length, and it did not vary much with the size of the pendent groups. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 831–841, 2002     

Synthesis and mesomorphic properties of side‐chain cholesteric liquid‐crystalline polymers containing menthyl groups

A series of new cholesteric liquid‐crystalline polysiloxanes ( P₁ – P₅ ) derived from menthyl groups were synthesized. The chemical structures of the monomers and polymers were characterized with Fourier transform infrared, ¹H‐NMR, ¹³C‐NMR, and elemental analyses. The mesomorphic properties and thermal behavior were investigated with differential scanning calorimetry, polarizing optical microscopy, thermogravimetric analysis, and X‐ray diffraction measurements. The influence of the polymer structure on the thermal behavior was discussed. The monomer diosgeninyl 4‐allyloxybenzoate exhibited a typical cholesteric oily‐streak texture and a focal‐conic texture. Polymers P₁ – P₅ showed thermotropic liquid‐crystalline properties. P₁ displayed a smectic fan‐shaped texture, P₂ – P₅ showed a cholesteric Grandjean texture, and P₆ and P₇ did not show mesomorphic properties. The experimental results demonstrated that the glass‐transition temperature and the clearing temperature decreased, and the mesomorphic properties weakened with an increasing concentration of menthyl units. Moreover, P₁ – P₅ exhibited wide mesophase temperature ranges and high thermal stability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5559–5565, 2006     

Mesomorphic properties of cholesteric side‐chain liquid crystalline polysiloxanes and elastomers

A series of crosslinked liquid crystalline polymers and corresponding uncrosslinked liquid crystalline polymers were prepared by graft copolymerization. Their liquid crystalline properties were characterized by differential scanning calorimetry, polarizing optical microscopy, and X‐ray diffraction measurements. The results showed that the crosslinking obtained in the isotropic state and the introduction of nonmesogenic crosslinking units into a polymeric structure could cause additional reduction of the clearing point (T_i) of the crosslinked polymers, compared with the corresponding uncrosslinked polymers. The crosslinked polymers (P‐2–P‐4) with a low crosslinking density exhibited cholesteric phases as did the uncrosslinked polymers. In contrast, a high crosslinking density made the crosslinked polymer P‐5 lose its thermotropic liquid crystalline property. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 773–778, 2004     

Synthesis and characterization of side‐chain cholesteric liquid‐crystalline polymers derived from steroid substituents

A series of new cholesteric liquid‐crystalline polysiloxanes derived from steroid substituents were synthesized. The chemical structures of the monomers or polymers obtained were characterized by FTIR, element analyses, ¹H NMR, and ¹³C NMR. Their mesogenic properties and thermal stability were investigated by differential scanning calorimetry, thermogravimetric analysis, polarizing optical microscopy, and X‐ray diffraction measurements. Monomers exhibited typical cholesteric focal‐conic or spiral texture. The polymers P ₁? P ₆ showed cholesteric phase and P ₇ displayed smectic phase. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Toughening liquid‐crystalline polymers with polyethylenes containing epoxy functionality

To improve toughness, a liquid‐crystalline polymer (LCPs) was blended with polyethylenes containing epoxy functionality in concentrations of 2, 6, and 15 wt %. The blends were prepared with a corotating twin‐screw extruder and were injection‐molded into specimens for mechanical testing. The effect of the amount of the epoxy‐functionalized polyethylenes on the morphology and mechanical and thermal properties was studied. The toughness improved with increasing amount of functionalized polyethylene, and the blend containing 15 wt % epoxy‐functionalized polyethylene had the best toughness properties. Impact strength values up to three times higher than those of the neat LCP were achieved. However, the stiffness of the LCP concurrently decreased substantially. The morphology became much more uniform, and the melting behavior changed. The results show that considerable improvements in the toughness properties of LCPs can be achieved with epoxy‐functionalized polyethylenes. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1886–1891, 2002     

The preparation and properties of segmented‐chain liquid crystalline polyesters based on 4,4′‐dihydroxybiphenyl by interfacial polycondensation

Thermotropic homopolyesters were prepared through interfacial polycondensation of 4,4′‐dihydroxybiphenyl with sebacoyl chloride. The optimal conditions of the process, in terms of the best yield, were studied through investigating the type of organic phase, amount of phase transfer agent, time and temperature of reaction, and volume ratio of aqueous to organic phase. The structure of the sample that had the best yield (53.235% ± 5%) was determined by means of elemental analysis, infrared spectra, and X‐ray. The effect of the molar ratio of the monomers on the yield and inherent viscosity was investigated. The inherent viscosity of the samples varied between 0.095 and 0.25 dL/g. The mesophase formed at elevated temperatures was studied by differential scanning calorimetry, polarized light microscopy, and depolarizing transmittance measurements. Our observations revealed that poly(4, 4′‐diphenyl sebacate), in contrast to previous reports that suggest this polymer is smectgenic, could produce nematic phase. It could be concluded that the chemical structure ordering of the poly(4, 4′‐diphenyl sebacate) plays a significant role in its liquid crystalline behavior. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1594–1606, 2005     

Synthesis and characterization of fluorine‐containing liquid crystalline polysiloxanes bearing cholesteryl cinnamate mesogens and trifluoromethyl‐substituted mesogens

Several novel side‐chain liquid crystalline (LC) polysiloxanes bearing cholesteryl cinnamate mesogens and trifluoromethyl‐substituted mesogens were synthesized by a one‐step hydrosilylation reaction with poly(methylhydrogeno)siloxane, a cholesteric LC monomer cholesteryl 3‐(4‐allyloxy‐phenyl)‐acryloate and a fluoro‐containing LC monomer 4‐[2‐(3‐trifluoromethyl‐phenoxy)‐acetoxy]‐phenyl 4‐allyloxy‐benzoate. The chemical structures and LC properties of the monomers and polymers were characterized by use of various experimental techniques, such as FTIR, ¹H‐NMR, ¹³C‐NMR, TGA, DSC, POM, and XRD. The temperatures at which 5% weight loss occurred were greater than 300°C for all the polymers, and the residue weight near 600°C increased slightly with increase of the trifluoromethyl‐substituted mesogens in the fluorinated polymer systems. The samples containing mainly cholesteryl cinnamate mesogens showed chiral nematic phase when they were heated and cooled, but the samples containing more trifluoromethyl‐substituted mesogens exhibited chiral smectic A mesophase. The glass transition temperature of the series of polymers increased slightly with increase of trifluoromethyl‐substituted mesogens in the polymer systems, but mesophase–isotropic phase transition temperature did not change greatly. In XRD curves, the intensity of sharp reflections at low angle increased with increase of trifluoromethyl‐substituted mesogens in the fluorinated polymers systems, indicating that the smectic order derived from trifluoromethyl‐substituted mesogens should be strengthened. These results should be due to the fluorophobic effect between trifluoromethyl‐substituted mesogens and the polymer matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis of liquid crystalline polymers from polyethylene terephthalate and 4‐acetoxybenzoic acid: A kinetic study

Liquid crystalline polymers (LCPs) have been synthesized from polyethylene terephthalate (PET) and 4‐acetoxybenzoic acid (OB) through melt step‐growth polymerization. The presence of liquid crystalline texture is first examined using optical polarizing microscopy. The thermal durability of the developed systems is studied through thermogravimetric analysis. The kinetics of the polymerization processes is analyzed. The effectiveness of three catalysts commonly used in polyesterification is investigated. The effect of reaction temperature is also examined. The progress of polycondensation reactions over time takes a nonlinear behavior of slight sigmoidal shape, irrespective of whether or not the reaction is catalyzed. Simple second and third order equations, along with a nonlinear model, are used to determine the kinetic parameters characterizing these reactions. The rate of reaction is enhanced when the reaction temperature is increased. Overall, second‐order kinetics well describes the polymerization reactions when the data set is divided into two regions. Antimony trioxide induces a more visible enhancement to the rate of reaction, compared to zinc acetate and sodium acetate. The presence of a catalyst generally increases the reaction activation energy. This indicates that entropy factors outweigh the increase in activation energy and drive the catalyzed reactions to completion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Side‐chain liquid‐crystalline polymers with a limonene‐co‐methyl methacrylate main chain: Synthesis and characterization of polymers with phenyl benzoate mesogenic groups

A new series of liquid‐crystalline polymers with a polymer backbone of limonene‐co‐methyl methacrylate were synthesized and characterized, and the spacer length was taken to be nine methylene units. The chemical structures of the obtained olefinic compound and polymers were confirmed with elemental analysis and proton nuclear magnetic resonance spectroscopy. The thermal behavior and liquid crystallinity of the polymers were characterized with differential scanning calorimetry and polarized optical microscopy. The polymers exhibited thermotropic liquid‐crystalline behavior and displayed a glass‐transition temperature at 48°C. The appearance of the characteristic schlieren texture confirmed the presence of a nematic phase, which was observed under polarized optical microscopy. These liquid‐crystalline polymers exhibited optical activity. A comparison was also made with polyacrylates and polymethacrylate‐based materials. This revealed that the nature of the polymer backbone had a major effect on the liquid‐crystalline properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4595–4600, 2006     

Synthesis and thermotropic liquid‐crystalline behavior of novel main‐chain poly(aryl ether ketones)

Novel aromatic poly(ether ketones) containing bulky lateral groups were synthesized via nucleophilic substitution reactions of 4,4′‐biphenol and (4‐chloro‐3‐trifluoromethyl)phenylhydroquinone (CF‐PH) with 1,4‐bis(p‐fluorobenzoyl)benzene. The copolymers were characterized by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, and polarized light microscopy observation. Thermotropic liquid‐crystalline behavior was observed in the copolymers containing 40, 50, 60, and 70 mol % CF‐PH. The crystalline–liquid‐crystalline transition [melting temperature (T_m)] and the liquid‐crystalline–isotropic phase transition appeared in the DSC thermograms, whereas the biphenol‐based homopolymer had only a melting transition. The novel poly(aryl ether ketones) had glass‐transition temperatures that ranged from 143 to 151°C and lower T_m's that ranged from 279 to 291°C, due to the copolymerization. The polymers showed high thermal stability, and some exhibited a large range in mesophase stability. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1347–1350, 2003     

Main‐chain liquid‐crystalline ionomers bearing potassium sulfonate groups

A series of thermotropic main‐chain liquid‐crystalline (LC) ionomers were prepared, which contained potassium sulfonate groups pendent to the chains. The polymers were prepared in an esterifying reaction with potassium ion contents ranging between 0 and 3.9 wt %. The content of potassium ion was characterized by spectrophotometric analysis with sodium tetraphenylboron as the titrant. Chemical structures were determined by various experimental techniques including Fourier transform IR spectroscopy and ¹H‐NMR. LC properties were characterized by differential scanning calorimetry, polarizing optical microscopy, and X‐rays. All of the polymers displayed nematic or smectic mesophases. With increasing potassium sulfonate ionic concentration in the polymers, the melting temperatures and isotropic transition temperatures changed little, whereas the temperature of the smectic A–nematic phase transition increased. The ionic aggregation was tangled with the rigid mesogenic groups of LC segments to form multiple block domains, leading the soft main chains to fold and form a lamellar structure due to their electrostatic interactions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2021–2026, 2005